NKK MS13LFW01E Miniature slide Datasheet

Miniature Slides
Series MS
Distinctive Characteristics
Bright, LED illumination at top of actuator.
Over-center actuator block and plunger design gives crisp
actuation, diminishes sparking, and increases operating life.
Guide interlocked with actuator block prevents
window locking and maintains correct plunger
alignment to assure contact stability.
Antijamming design protects contacts from
damage due to excessive downward force
on the actuator.
High internal barriers between poles and
insulating sheet between case and actuator
block give added protection to contacts.
Prominent external insulating barriers increase
insulation resistance and dielectric strength.
Epoxy sealed terminals prevent entry of flux, solvents,
and other contaminants.
Clinching of frame to case well above base and terminals provides
1,500V dielectric strength.
Actual Size
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
07-07
Miniature Slides
Series MS
General Specifications
Electrical Capacity (Resistive Load)
Power Level:
Other Ratings
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Contact Timing:
Total Travel:
Materials & Finishes
Actuator:
Frame:
Case:
Movable Contacts:
Stationary Contacts:
Terminals:
Environmental Data
Operating Temp Range:
Humidity:
Vibration:
Shock:
Processing
Soldering Time & Temp:
Cleaning:
Standards & Certifications
Flammability Standards:
6A @ 125V AC or 3A @ 250V AC
10 milliohms maximum
1,000 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
50,000 operations minimum
25,000 operations minimum
Nonshorting (break-before-make)
.087” (2.2mm)
Glass fiber reinforced polyester
Stainless steel
Glass fiber reinforced diallyl phthalate resin (UL94V-0)
Silver alloy
Silver capped copper with silver plating
Copper or brass with silver plating
–10°C through +55°C (+14°F through +131°F)
90 ~ 95% humidity for 240 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Wave Soldering Recommended (PC version): See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Note: Lever must be in center position while soldering.
These devices are not process sealed. Hand clean locally using alcohol based solution.
UL94V-0 rated case
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
07-07
Series MS
Miniature Slides
TYPICAL SWITCH ORDERING EXAMPLE
MS
1
2
POLES
1
L
F
L
01
LED Lighted
MOUNTING
2
ON
NONE
ON
3
ON
OFF
ON
LEDS
Silver; Rated
6A @ 125V AC &
3A @ 250V AC
W
CIRCUITS
C
CONTACT MATERIALS
& RATINGS
ILLUMINATION
SPDT
W
N
For Straight PC
(Terminal 03 only)
F
With 2-screw Flange
(Terminal 01 only)
C
Red
E
Yellow
F
Green
TERMINALS
01
Solder Lug
03
Straight PC
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
MS12LFW01C
Red LED Illumination
2-screw Flange Frame
Silver Contacts with 6-Amp Rating
SPDT ON-NONE-ON Circuit
Solder Lug Terminals
POLES & CIRCUITS
Slide Position
Pole
SP
Connected Terminals
Left
Center
Right
MS12
ON
NONE
ON
MS13
ON
OFF
ON
Left
Center
Throw & Schematics
Right
Model
Note: Terminal numbers are not actually on
the switch. LED circuit is isolated and
requires an external connection.
2 (COM)
2-1
OPEN
2-3
SPDT
L(+)
1
3
4
L(-)
6
CONTACT MATERIALS & RATINGS
W
Silver over Silver
Power Level
6A @ 125V AC & 3A @ 250V AC
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
07-07
Series MS
Miniature Slides
MOUNTING TYPES & TERMINALS
N
F
Straight PC Mount
(Combines with
Straight PC Terminal
03 only)
03
2-screw Flange
(Combines with Solder
Lug Terminal 01 only)
01
Straight PC
(6.35) (4.8)
.250 .189
Epoxy Seal
(1.17) Typ
.046
(4.8)
.189
Thk = (0.8) Typ
.031
(2.0)
.079
(4.0)
.157
Epoxy Seal
Solder Lug
(6.35) (4.8)
.250 .189
(2.0)
.079
(1.1)
.043
(1.17)
.046
(4.8)
.189
Thk = (0.8) Typ
.031
LED COLORS & SPECIFICATIONS
LEDs are supplied as an integral part
of the switch (not available separately). The lamp circuit is independent of
switch operation. Electrical specifications shown are determined at a basic
temperature of 25°C.
If the source voltage exceeds the rated
voltage, a ballast resistor is required.
The resistor value can be calculated
by using the formula given in the
Supplement.
(+)
(-)
C
Color
E
Red
F
Yellow
Green
Forward Peak Current
IFM
30mA
30mA
25mA
Continuous Forward Current
IF
16mA
16mA
16mA
Forward Voltage
VF
1.98V
2.06V
2.16V
Reverse Peak Voltage
VRM
5V
5V
5V
Current Reduction Rate Above 25°C
∆IF
0.40mA/°C
0.42mA/°C
0.33mA/°C
Ambient Temperature Range
–15° ~ +60°C
TYPICAL SWITCH DIMENSIONS
Solder Lug Terminals
(1.2) R Typ
.047
(5.0)
.197
Circuit Mark
This Side
(2.0) Typ
.079
(6.1)
.240
(8.2)
.323
(5.1)
.201
(12.7)
.500
2
(4.7) Typ
.185
(17.53)
.690
(0.5)
.020
(4.8)
.189
(11.9)
.469
(0.4) (4.5)
.016 .177
(7.6) (6.35)
.299
.250
(6.8)
.268
1
4
Direction of Actuation
(3.8)
.150
(2.4)
.094 Dia Typ
3
6
(17.53)
.690
(19.6)
.772
(2.0)
.079
MS12LFW01C
(1.17) Typ
.046
(1.1) x (2.0) Typ
.043 x .079
(0.8) Typ
.031
(9.0)
.354
Maximum Panel Thickness .197” (5.0mm)
Actuator in LEFT Position
Straight PC Terminals
Circuit Mark
This Side
(5.0)
.197
(1.17) Typ
.046
(0.8) Typ
.031
(3.8)
.150
(2.0)
.079
(8.2)
.323
MS12LNW03C
(4.7) Typ
.185
(5.1)
.201
(7.6)
.299
Actuator in LEFT Position
(4.8)
.189
(6.35)
.250
3
3
2
(12.7)
.500
(4.8)
.189
(11.9)
.469
(0.5)
.020
(4.7) Typ
.185
2
1
1
4
6
(6.8)
.268
4
(1.8) Dia Typ
.073
(9.0)
.354
Direction of Actuation
6
(4.8)
.189
Maximum Panel Thickness .197” (5.0mm)
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com
07-07
Similar pages