ISO-9001 CERTIFIED BY DSCC M.S.KENNEDY CORP. DUAL RAD TOLERANT +/VOLTAGE REGULATOR 5901RH SERIES 4707 Dey Road Liverpool, N.Y. 13088 (315) 701-6751 FEATURES: MIL-PRF-38534 CERTIFIED 25KRAD(SI) Total Dose Performance Internal Thermal Overload Protection Output Current to 1.5 Amps Output Voltage Internally Trimmed to ±1% Accuracy Available to DSCC SMD #TBD Lead Form Options: Straight and Gull Wing Alternate Voltage Combinations Available MSK590XRH DESCRIPTION: MSK590XRHG The MSK 5901RH series are dual Radiation Tolerant +/- voltage regulators offering low dropout and output accuracy to ±1% maximum. Excellent line and load regulation characteristics ensure highly accurate performance. In radiation environments, a total dose rating of 25KRAD(SI) provides highly reliable performance. The MSK 5901RH series regulators are equipped with internal thermal overload protection. The devices are packaged in a space efficient 20 pin flatpack with two lead form options, straight and gull wing. EQUIVALENT SCHEMATIC TYPICAL APPLICATIONS PIN-OUT INFORMATION 1 2 3 4 5 6 7 8 9 10 Switching Power Supply Post Regulators Constant Voltage/Current Regulators High Efficiency Linear Regulators 1 -VRTN -VOUT -VOUT -VOUT -VOUT +VRTN +VOUT +VOUT +VOUT +VOUT 20 19 18 17 16 15 14 13 12 11 -VIN -VIN -VIN -VIN -Ccomp +Ccomp +VIN +VIN +VIN +VIN Rev. D 7/05 ABSOLUTE MAXIMUM RATINGS +VIN -VIN PD +IOUT -IOUT TJ +Input Voltage (VIN-VOUT) -Input Voltage (VIN-VOUT) Power Dissipation +Output Current -Output Current Junction Temperature ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ +40VDC -40VDC Internally Limited 1.5A 1.5A +150°C ○ ○ ○ 8 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ TST Storage Temperature Range TLD Lead Temperature Range (10 Seconds) TC Case Operating Temperature MSK 5901RH-5909RH MSK 5901RH-5909RH(K/H/E) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ -65°C to +150°C 300°C ○ ○ ○ ○ ○ ○ -40°C to +85°C -55°C to +125°C ○ ELECTRICAL SPECIFICATIONS Parameter Test Conditions Group A MSK 590XRH K/H/E 3 Subgroup Typ. Min. Max. 4 7 MSK 590XRH 2 Units Min. Typ. Max. POSITIVE OUTPUT REGULATORS: 1 - ±0.2 ±1.0 - ±0.2 ±1.5 % 2,3 - ±0.8 ±3.0 - - - % 1 - 1.6 3.0 - 1.6 3.5 V 2,3 - 1.9 3.0 - - - V 1 - ±0.2 ±2.0 - ±0.2 ±2.5 % V IN=VOUT+3V 2,3 - ±0.4 ±2.5 - - - % IOUT=10mA 1 - ±0.6 ±1.5 - ±0.6 ±2.0 % VOUT+3V≤V IN≤35V 2,3 - ±1.0 ±2.5 - - - % JUNCTION TO CASE @ 125°C - - 9.5 10.5 - 9.5 1 - ±0.2 ±1.0 - ±0.2 ±1.5 % 2,3 - ±0.8 ±3.0 - - - % 1 - 1.9 3.0 - 1.9 3.0 V 2,3 - 1.5 3.0 - - - V 10mA≤IOUT≤0.5A 1 - ±0.2 ±2.0 - ±0.2 ±2.5 % VIN=VOUT -3V 2,3 - ±0.4 ±2.5 - - - % IOUT=10mA 1 - ±0.1 ±1.5 - ±0.1 ±2.0 % -30V≤V IN≤VOUT-3V 2,3 - ±0.2 ±2.5 - - - % - - 11.5 12.5 - 11.5 Output Voltage Tolerance IOUT=10mA; VIN=VOUT+3V IOUT=0.5A; ∆V OUT=1% Dropout Voltage 10mA≤IOUT≤0.5A Load Regulation Line Regulation Thermal Resistance 1 11.0 °C/W NEGATIVE OUTPUT REGULATORS: Output Voltage Tolerance Dropout Voltage Load Regulation Line Regulation Thermal Resistance 1 IOUT=10mA; VIN=VOUT -3V IOUT=0.5A; ∆V OUT=1% JUNCTION TO CASE @ 125°C PART 5 NUMBER NOTES: 1 2 3 4 5 6 7 8 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only. Industrial grade and "E" suffix devices shall be tested to subgroup 1 unless otherwise specified. Military grade devices shall be 100% tested to subgroups 1,2 and 3. Subgroup 1 TA=TC=+25°C Subgroup 2 TA=TC=+125°C Subgroup 3 TA=TC=-55°C Please consult the factory if alternate output voltages are required. For positive regulator, output decoupled to ground using 1µF minimum tantalum capacitor unless otherwise specified. For negative regulator, output decoupled to ground using 1µF minimum tantanlum capacitor. For complete radiation test data, consult "MSK 5901RH Total Dose Test Report". Continuous operation at or above absolute maximum ratings may adversly effect the device performance and/or life cycle. 2 13.0 °C/W OUTPUT VOLTAGES POSITIVE NEGATIVE MSK5901 5.0 5.0 MSK5902 5.0 5.2 MSK5903 12.0 5.0 MSK5904 12.0 12.0 MSK5905 15.0 15.0 MSK5906 15.0 5.0 MSK5907 5.0 12.0 MSK5908 5.0 15.0 MSK5909 10.0 10.0 Rev. D 7/05 APPLICATION NOTES TYPICAL APPLICATION CIRCUIT CAPACITOR SELECTION POSITIVE REGULATOR INPUT CAPACITOR: An input bypass capacitor is recommenced when using the MSK 5901 series regulators. This is especially true if the regulator is located farther than 6 inches from the power supply filter capacitors. For most applications a 1µF solid tantalum capacitor will be suitable. LOAD REGULATION OUTPUT CAPACITOR: A minimum of a 1µF solid tantalum capacitor should also be used at the output to insure stability. Any increase of this output capacitor larger than 10µF will only improve output impedance. It is important to keep the output connection between the regulator and the load as short as possible since this directly affects the load regulation. For example, if 20 gauge wire were used which has a resistance of about 0.008 ohms per foot, this would result in a drop of 8mV/ft at 1Amp of load current. It is also important to follow the capacitor selection guidelines to achieve best performance. +CCOMP CAPACITOR: For improved ripple rejection, +Ccomp can be bypassed to ground with a 10µF tantalum capacitor. This bypass capacitor will provide 80dB ripple rejection. Increased capacitance above 10µF does not improve the ripple rejection at frequencies above 120Hz. If the Ccomp bypass capacitor is used, it may be necessary to add a protection diode to protect the regulator from capacitor discharge damage. See Typical Applications Circuit for clarification. If the bypass capacitor is not used, it should be left open since it is internally connected to the regulator. HEAT SINKING To determine if a heat sink is required for your application and if so, what type, refer to the thermal model and governing equation below. Governing Equation: Tj = Pd x (Rθjc + Rθcs + Rθsa) + Ta WHERE Tj = Junction Temperature Pd = Total Power Dissipation Rθjc = Junction to Case Thermal Resistance Rθcs = Case to Heat Sink Thermal Resistance Rθsa = Heat Sink to Ambient Thermal Resistance Tc = Case Temperature Ta = Ambient Temperature Ts = Heat Sink Temperature NEGATIVE REGULATOR INPUT CAPACITOR: Once again, if the regulator will be farther than 6 inches from power supply filter capacitors, then an input capacitor will be required on the negative regulator. It is recommended that a 1µF solid tantalum capacitor be used. EXAMPLE: This example demonstrates an analysis where the output currents are at 0.5 amp each and both inputs are 8V. OUTPUT CAPACITOR: A minimum of a 1µF solid tantalum capacitor should also be used at the output to insure stability. Any increase of this output capacitor larger than 10µF will only improve output impedance. Conditions for MSK 5901RH: +Vin = +8.0V; Iout = 0.5A Positive Regulator 1.) Assume 45° heat spreading model. 2.) Find positive regulator power dissipation: -CCOMP CAPACITOR: For improved ripple rejection, -Ccomp can be bypassed to ground with a 10µF tantalum capacitor. This bypass capacitor will provide 80dB ripple rejection. Increased capacitance above 10µF does not improve the ripple rejection at frequencies above 120Hz. If the Ccomp bypass capacitor is used, it may be necessary to add a protection diode to protect the regulator from capacitor discharge damage. See Typical Applications Circuit for clarification. If the bypass capacitor is not used, it should be left open since it is internally connected to the regulator. Pd = (Vin - Vout)(Iout) Pd = (+8V-5V)(0.5A) Pd = 1.5W 3.) For conservative design, set Tj = +125°C Max. 4.) For this example, worst case Ta = +90°C. 5.) Rθjc = 10.5°C/W from the Electrical Specification Table. 6.) Rθcs = 0.15°C/W for most thermal greases. 7.) Rearrange governing equation to solve for Rθsa: Rθsa= ((Tj - Ta)/Pd) - (Rθjc) - (Rθcs) = (125°C-90°C)/1.5W - 10.5°C/W - 0.15°C/W = 12.7°C/W The same exercise must be performed for the negative regulator. 3 Rev. D 7/05 TYPICAL PERFORMANCE CURVES POSITIVE NEGATIVE 4 Rev. D 7/05 MECHANICAL SPECIFICATIONS MSK590XRH WEIGHT= 3.3 GRAMS TYPICAL NOTE: ALL DIMENSIONS ARE ±0.010 INCHES UNLESS OTHERWISE LABELED. ESD Triangle indicates pin 1. ORDERING INFORMATION Part Number Screening Level MSK590XRH Industrial MSK590XHRH MIL-PRF-38534 CLASS H MSK590XKRH MIL-PRF-38534 CLASS K MSK590XERH EXTENDED RELIABILITY DSCC SMD TBD TBD X - Designates voltage selection (MSK 5901-5909) 5 Rev. D 7/05 MECHANICAL SPECIFICATIONS CONTINUED MSK590XRHG WEIGHT= 3.3 GRAMS TYPICAL NOTE: ALL DIMENSIONS ARE ±0.010 INCHES UNLESS OTHERWISE LABELED. ESD Triangle indicates pin 1. ORDERING INFORMATION Part Number Screening Level MSK590XRHG Industrial MSK590XHRHG MIL-PRF-38534 CLASS H MSK590XKRHG MIL-PRF-38534 CLASS K MSK590XERHG EXTENDED RELIABILITY DSCC SMD TBD TBD X - Designates voltage selection (MSK 5901-5909) M.S. Kennedy Corp. 4707 Dey Road, Liverpool, New York 13088 Phone (315) 701-6751 Fax (315) 701-6752 www.mskennedy.com The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet. Contact MSK for MIL-PRF-38534 Class H, Class K and Appendix G (radiation) status. 6 Rev. D 7/05