MTL6400U SINGLE CHANNEL OPTOCOUPLER (Electrically similar to 6N140) Features: Applications: • • • • • • • • • • High Reliability High Current Ration: 300% Typical Rugged surface mount package Low Input current requirement: 0.5mA +1.5kV electrical isolation Military and Space Level shifting Line receiver Switching power supplies Communication Systems DESCRIPTION The MTL6400U contains a gallium aluminum arsenide LED optically coupled to a silicon photodarlington detector. The optocoupler is built in a 6-pin leadless chip carrier. This optocoupler is capable of transmitting signals between two galvanic sources. The potential difference between transmitter and receiver should not go over the maximum isolation voltage. Also available screened to MIL-STD-883. ABSOLUTE MAXIMUM RATINGS Input Diode Peak Forward Input Current (Value applies for tw < 1ms, 500 pps) ..............................................................................................................20mA Average Input Current, I F (Note 1)……………………………………………...….…………………………………………..10mA Reverse Input Voltage, VR………………………………………………………………………………………………………….5V Output Photodetector Output Current, I O …………………………………………………………………………………………………………….….40mA Output Voltage, VO ……………………………………………………………………………………………..………..-0.5V to 18V Supply Voltage, VCC……………………………………………………………………………………….…………….-0.5V to 20V Output Power Dissipation (Note 2)…………………………………………………………………………………...……….75mW Storage Temperature.................................................................................................................................................................................. -65°C to +150°C Operating Free-Air Temperature Range.................................................................................................................................................-55°C to +125°C Lead Solder Temperature (vapor phase reflow for 30 sec.) ............................................................................................................................215°C Notes: 1. Derate I F at 0.66mA/°C above 110°C 2. Output power is collector output power plus one half of the total supply power. Derate at 5mW/°C above 110°C. RECOMMENDED OPERATING CONDITIONS: SYMBOL MIN MAX I FL 0 1 I FH 0.5 5 VCE 5 18 TA -55 125 SELECTION GUIDE PART DESCRIPTION Single Channel optocoupler, commercial (0° to+70°C operating temperature range) Single Channel optocoupler, commercial (-40° to +85°C operating temperature range) Single Channel optocoupler, commercial (-55° to +125 operating temperature range) PARAMETER Input Current, Low Level Input Current, High Level Supply Voltage Operating Temperature PART NUMBER MTL64X0U.001.X MTL64XOU.002.X MTL64X0U.003.X MTL64X0U.004.X NOTE: UNITS µA mA V °C Single Channel optocoupler, w/100% device screening -55° to +125°Coperating temperature range) Replace first X with 0 or 2 to indicate type of part required. X at end of part number represents lead finish. Replace with A for gold or S for solder. MINCO TECNHOLOGY LABS, INC. ♦ 1805 Rutherford Lane, Austin, TX 78754 ♦ TEL: 512.834.2022 ♦ FAX: 512.837.6285 MTL6400U SINGLE CHANNEL OPTOCOUPLER (Electrically similar to 6N140) ELECTRICAL CHARACTERISTICS INPUT DIODE TA = 25°C unless otherwise specified. SYMBOL MIN Input Reverse Breakdown Voltage PARAMETER BV R 5 Input Diode Static Forward Voltage VF TYP MAX UNITS TEST CONDITIONS V IR = 10µA 1.8 V IF = 1.6mA Input Diode Static Forward Voltage -55°C VF 1.5 1.8 V IF = 1.6mA Input Diode Static Forward Voltage +100°C VF 1.2 1.8 V IF = 1.6mA MAX UNITS TEST CONDITIONS % IF = 0.5mA, V O = 0.4V, V CC = 4.5V IF = 1.6mA, V O = 0.4V, V CC = 4.5V COUPLED CHARACTERISTICS TA = 25°C unless otherwise specified. PARAMETER Current Transfer Ration SYMBOL MIN TYP CTR 300 1500 300 1000 % 200 500 % IF = 5.0mA, V O = 0.4V, V CC = 4.5V V IF = 0.5mA, IOL = 1.5mA, V CC = 4.5V IF = 0.5mA, IOL = 10mA, V CC = 4.5V Logic Low Output Voltage VOL Logic Low Output Voltage 0.1 0.4 VOL 0.2 0.4 V Logic High Output Current IOH 0.01 250 µA VO = VCC = 18V Logic Low Supply Current ICCL 0.4 1.0 mA IF = 1.6mA, V CC = 18V Logic High Supply Current ICCH 0.01 10 µA 1.0 µA IF = 0mA, V CC = 18V 45% Relative Humidity, TA = 25°C t = 5 sec, V I-O = 1500Vdc Input-Output Insulation Leakage Current II-O Resistance (Input-Output) RI-O 10 Ω 12 pF V IN-OUT = 500V f = 1MHz, TA = 25°C 60 µs VCC = 5V, IF = 0.5mA, RL = 4.7kΩ 20 µs VCC = 5V, IF = 5mA, RL = 680Ω 30 100 µs VCC = 5V, IF = 0.5mA, RL = 4.7kΩ 2.0 5.0 µs VCC = 5V, IF = 5mA, RL = 680Ω VCM = 50VP-P, VCC = 5.0V RL = 1.5KΩ, IF = 0mA VCM = 50VP-P, VCC = 5.0V RL = 1.5KΩ, IF = 1.69mA Input to Output Capacitance C IO 1.5 Propagation Delay Time to High Output Level tPLH 6.0 4.0 Propagation Delay Time to Low Output Level tPHL Common Mode Transient Immunity At High Output Level Common Mode Transient Immunity At Low Output Level CMH 500 1000 V/µs CML 500 1000 V/µs Package Dimensions Schematic Diagram MINCO TECNHOLOGY LABS, INC. ♦ 1805 Rutherford Lane, Austin, TX 78754 ♦ TEL: 512.834.2022 ♦ FAX: 512.837.6285