SURFACE MOUNT GALSS PASSIVATED ZENER DIODE Zener Voltage MZ1.5PB11V-34.1 THRU MZ1.5PB200V-1.9 11 to 200 Volts Steady state Power 1.5 Watts FEATURES • • • • • • • • DO-214AA(SMB) For surface mounted applications in order to Optimize board space Low profile package Built-in strain relief Glass passivated junction Low inductance Typical IR less than 1μA above 11V High temperature soldering: 260℃/10 seconds at terminals Plastic package has Underwriters Laboratory Flammability Classification 94V-O MECHANICAL DATA • • • • • Dimensions in inches and (millimeters) Cass: JEDEC DO-214AA,molded plastic over passivated junction Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes positive end (cathode) Standard Packaging: 12mm tape (EIA-481) Weight: 0.003 ounces, 0.93 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • Ratings at 25℃ ambient temperature unless otherwise specified Symbols DC Power Dissipation @ TL=75℃, Measure at Zero Lead Length (Note 1 Fig.1) Derate above 75℃ Peak forward Surge Current 8.3ms single half sine/square wave Superimposed on rated load (JEDEC Method) (Notes 1.2) Operating junction and Storage Temperature Range PD Value Unit IFSM 1.5 15 10 Watts mw/℃ Amps TJ, TSTG -55to~+150 ℃ Notes : 1. Mounted on 5.0mm2(.013mm thick) land areas 2. Measured on 8.3ms, single half sine-wave or equivalent square wave, duty cycle=4 pulses per minute maximum. E-mail: [email protected] Web Site: www.cnmic.com SURFACE MOUNT GALSS PASSIVATED ZENER DIODE Zener Voltage MZ1.5PB11V-34.1 THRU MZ1.5PB200V-1.9 Type MZ1.0PB11V-34.1 MZ1.0PB12V-31.2 MZ1.0PB13V-28.8 MZ1.0PB15V-25 MZ1.0PB16V-23.4 MZ1.0PB18V-20.8 MZ1.0PB20V-18.7 MZ1.0PB22V-17 MZ1.0PB24V-15.6 MZ1.0PB27V-13.9 MZ1.0PB30V-12.5 MZ1.0PB33V-11.4 MZ1.0PB36V-10.4 MZ1.0PB39V-9.6 MZ1.0PB43V-8.7 MZ1.0PB47V-8.0 MZ1.0PB51V-7.3 MZ1.0PB56V-6.7 MZ1.0PB62V-6.0 MZ1.0PB68V-5.5 MZ1.0PB75V-5.0 MZ1.0PB82V-4.6 MZ1.0PB91V-4.1 MZ1.0PB100V-3.7 MZ1.0PB110V-3.4 MZ1.0PB120V-3.1 MZ1.0PB130V-2.9 MZ1.0PB150V-2.5 MZ1.0PB160V-2.3 MZ1.0PB180V-2.1 MZ1.0PB200V-1.9 Device Marking Code 11V-34.1 12V-31.2 13V-28.8 15V-25 16V-23.4 18V-20.8 20V-18.7 22V-17 24V-15.6 27V-13.9 30V-12.5 33V-11.4 36V-10.4 39V-9.6 43V-8.7 47V-8.0 51V-7.3 56V-6.7 62V-6.0 68V-5.5 75V-5.0 82V-4.6 91V-4.1 100V-3.7 110V-3.4 120V-3.1 130V-2.9 150V-2.5 160V2.3 180V-2.1 200V-1.9 Nominal Zener Voltage Vz@IZT Volts (Note 1) 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 100 110 120 130 150 160 180 200 Test Current IZT mA 34.1 31.2 28.8 25 23.4 20.8 18.7 17 15.6 13.9 12.5 11.4 10.4 9.6 8.7 8 7.3 6.7 6 5.5 5 4.6 4.1 3.7 3.4 3.1 2.9 2.5 2.3 2.1 1.9 Steady state Power Max Zener Impedance (Note 2) ZZT@IZT Ohms 5.5 6.5 7 9 10 12 14 17.5 19 23 26 33 38 45 53 67 70 86 100 120 140 160 200 250 300 380 450 600 700 900 1200 11 to 200 Volts ZZk ZZk Max Reverse Leakage Current IR @ Ohms 550 550 550 600 600 650 650 650 700 700 750 800 850 900 950 1000 1100 1300 1500 1700 2000 2500 3000 3100 4000 4500 5000 6000 6500 7000 8000 1.5 Watts VR @ mA 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 μA 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Notes:TOLERANCE AND VOLTAGE DESIGNATION Tolerance designation-The type numbers listed indicate a tolerance of ±5% E-mail: [email protected] Web Site: www.cnmic.com Volts 8.4 9.1 9.9 11.4 12.2 13.7 15.2 16.7 18.2 20.6 22.8 25.1 27.4 29.7 32.7 35.8 38.8 42.6 47.1 51.7 56 62.2 69.2 76 83.6 91.2 98.8 114 121.6 136.8 152 Maximum DC Zener Current IZM mAdc 136 125 115 100 93 83 75 68 62 55 50 45 41 38 34 31 29 26 24 22 20 18 16 15 13 12 11 10 9 8 7 SURFACE MOUNT GALSS PASSIVATED ZENER DIODE Zener Voltage MZ1.5PB11V-34.1 THRU MZ1.5PB200V-1.9 11 to 200 Volts Steady state Power 1.5 Watts RATING AND CHARACTERISTIC CURVES MZ1.5PB11V-34.1 THRU MZ1.5PB200V-1.9 FIG.1- STEADY STATE POWER DERATING FIG.2- ZENER VOLTAGE-TO 12 VOLTS θVZ,TEMPERATURE COEFICIENT (mV/ ℃) PD, MAXIMUM POWER DISSIPATION (WATTS) 2.5 2 1.5 1 0.5 0 0 20 40 60 80 100 120 140 150 10 8 Vz@IZT 6 4 2 0 -2 -4 180 2 4 TL, LEAD TEMPERATURE(℃) FIG.3- ZENER VOLTAGE-14 TO 200 VOLTS 8 10 12 FIG.4- EFFECT OF ZENER CURRENT 200 Zz, DYNMIC IMPEDANCE ( OHMS) 1K Vz@IZT 100 70 50 30 20 10 10 20 30 50 70 100 200 TJ =25℃ 500 Iz(ms)=0.1 Iz(dc) 200 Vz=150V 100 91V 50 62V 20 10 5 22V 2 12V 1 0.5 1 2 5 FIG.5- EFFECT OF ZENER VOLTAGE 200 IZ(dc)=1mA 100 70 50 0.0 20 10mA 10 7 5 3 2 20mA 5 7 10 20 50 100 IZ, ZENER TEST CURRENT (mA) VZ, ZENER VOLTAGE (VOLTS) Zz, DYNMIC IMPEDANCE ( OHMS) θVZ,TEMPERATURE COEFICIENT (mV/℃) 6 VZ, ZENER VOLTAGE ( VOLTS) 10 IZ(rms)=0.1 IZ(dc) 20 30 50 70 100 VZ, ZENER VOLTAGE (VOLTS) E-mail: [email protected] Web Site: www.cnmic.com 200 6.8V 500 SURFACE MOUNT GALSS PASSIVATED ZENER DIODE Zener Voltage MZ1.5PB11V-34.1 THRU MZ1.5PB200V-1.9 11 to 200 Volts Steady state Power 1.5 Watts RATING AND CHARACTERISTIC CURVES MZ1.5PB11V-34.1 THRU MZ1.5PB200V-1.9 FIG.7- Vz=12 thru 82 Volts 100 1K RECTANGULAR NONREPETITIVE WAVEFORM TJ=25℃ PRIOR TO INTIAL PULSE 500 300 200 50 Iz, ZENER CURRENT(mA) Ppk, PEAKSURGE POW ER(WATTS) FIG.6- Maximum Surge Power 100 50 30 20 10 0.1 0.2 0.3 0.5 1 2 3 5 10 20 30 50 PW, PULSE WIDTH (ms) NOTE 6. ZENER VOLTAGE (Vz) MEASUREMENT Nominal zener voltage is measured with the device function in thermal equilibrium with ambient temperature at 25 ℃ E-mail: [email protected] 100 30 20 10 5 3 2 1 0.5 0.3 0.2 0.1 0 10 20 30 40 50 60 70 80 90 Vz,ZENER VOLTAGE(VOLTS) NOTE 7. ZENER IMPEDANCE (Zz)DERIVATION Zzt anc Zzk are measured by dividing the ac voltage drop across the device by the accurrent applied. The specified limits are for Iz (ac )=0.1 lz, (dc )with the ac freqency = 60Hz Web Site: www.cnmic.com 100