INTEGRATED CIRCUITS 74F153 Dual 4-line to 1-line multiplexer Product specification IC15 Data Handbook 1996 Jan 05 Philips Semiconductors Product specification Dual 4-line to 1-line multiplexer 74F153 FEATURES PIN CONFIGURATION • Non-inverting outputs • Separate enable for each section • Common select inputs • See 74F253 for 3-State version Ea 1 16 VCC S1 2 15 Eb I3a 3 14 S0 I2a 4 13 I3b I1a 5 12 I2b I0a 6 11 I1b Ya 7 10 I0b GND 8 9 Yb DESCRIPTION The 74F153 is a dual 4-input multiplexer that can select 2 bits of data from up to four sources selected by common Select inputs (S0, S1). The two 4-input multiplexer circuits have individual active-Low Enables (Ea, Eb) which can be used to strobe the outputs independently. Outputs (Ya, Yb) are forced Low when the corresponding Enables (Ea, Eb) are High. SF00146 The 74F153 is the logic implementation of a 2-pole, 4-position switch where the switch is determined by the logic levels supplied to the common select inputs. TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F153 7.0ns 12mA ORDERING INFORMATION DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C PKG. DWG. # 16-pin plastic DIP N74F153N SOT38-4 16-pin plastic SO N74F153D SOT109-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW I0a – I3a PINS Port A data inputs DESCRIPTION 1.0/1.0 20µA/0.6mA I0b – I3b Port B data inputs 1.0/1.0 20µA/0.6mA Common Select inputs 1.0/1.0 20µA/0.6mA Ea Port A Enable input (active Low) 1.0/1.0 20µA/0.6mA Eb Port B Enable input (active Low) 1.0/1.0 20µA/0.6mA Port A, B data outputs 50/33 1.0µA/20mA S0, S1 Ya, Yb NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state. LOGIC SYMBOL IEC/IEEE SYMBOL 14 6 5 4 3 10 11 12 13 2 I0a I1a I2a I3a I0b I1b I2b 1 I3b 6 14 S0 2 S1 1 Ea 15 Eb 5 4 3 0 G 1 EN 0 1 0 3 MUX 7 2 3 15 Ya Yb 10 11 9 12 7 13 9 VCC = Pin 16 GND = Pin 8 SF00148 SF00147 1996 Jan 05 2 853–0100 16187 Philips Semiconductors Product specification Dual 4-line to 1-line multiplexer 74F153 LOGIC DIAGRAM Ea 1 I0a 6 I1a 5 I2a 4 I3a 3 S1 S2 2 I0b 14 10 I0b I2b I3b 11 12 13 7 VCC = Pin 16 GND = Pin 8 Eb 15 9 Ya Yb SF00149A FUNCTION TABLE INPUTS OUTPUT S0 S1 En I0n I1n I2n I3n Yn X X H X X X X L L L L L X X X L L L L H X X X H H L L X L X X L H L L X H X X H L H L X X L X L L H L X X H X H H H L X X X L L H H L X X X H H H = High voltage level L = Low voltage level X = Don’t care 1996 Jan 05 3 Philips Semiconductors Product specification Dual 4-line to 1-line multiplexer 74F153 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state Tamb Operating free-air temperature range Tstg Storage temperature range 40 mA 0 to +70 °C –65 to +150 °C RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL PARAMETER UNIT MIN NOM MAX 5.0 5.5 VCC Supply voltage 4.5 V VIH High-level input voltage 2.0 VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IOH High-level output current –1 mA IOL Low-level output current 20 mA Tamb Operating free-air temperature range +70 °C V 0 DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL TEST CONDITIONS1 PARAMETER LIMITS MIN TYP2 MAX UNIT VCC = MIN, VIL = MAX ±10%VCC 2.5 VIH = MIN, IOH = MAX ±5%VCC 2.7 VCC = MIN, VIL = MAX ±10%VCC 0.30 0.50 VIH = MIN, IOL = MAX ±5%VCC 0.30 0.50 –0.73 –1.2 V 100 µA VOH O High level output voltage High-level VOL O Low level output voltage Low-level VIK Input clamp voltage VCC = MIN, II = IIK II Input current at maximum input voltage VCC = MAX, VI = 7.0V IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V –0.6 mA IOS Short-circuit output current3 VCC = MAX –150 mA 12 20 mA ICC Supplyy current ((total)) 12 20 mA ICCH V 3.4 V –60 En = GND, Sn=In=4.5V VCC = MAX ICCL En=Sn=In=GND NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. 1996 Jan 05 4 Philips Semiconductors Product specification Dual 4-line to 1-line multiplexer 74F153 AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL VCC = +5.0V ± 10% Tamb = 0°C to +70°C CL = 50pF, RL = 500Ω VCC = +5.0V Tamb = +25°C CL = 50pF, RL = 500Ω TEST CONDITION PARAMETER MIN TYP MAX MIN MAX UNIT tPLH tPHL Propagation delay In to Yn Waveform 1 3.0 3.0 4.5 5.0 7.0 7.5 2.5 2.5 8.0 8.0 ns tPLH tPHL Propagation delay Sn to Yn Waveform 2 5.0 5.0 8.0 8.0 10.5 10.5 4.5 4.5 12.0 12.0 ns tPLH tPHL Propagation delay En to Yn Waveform 2 5.0 4.0 7.5 5.5 9.0 7.0 4.5 3.5 10.5 8.0 ns AC WAVEFORMS For all waveforms, VM = 1.5V. In Sn VM VM tPLH VM Yn VM VM En tPHL tPHL VM tPLH VM Yn VM SF00150 SF00151 Waveform 1. Propagation Delay, Data to Output Waveform 2. Propagation Delay, Enable and Select to Output TEST CIRCUIT AND WAVEFORMS VCC NEGATIVE PULSE VIN tw 90% 10% D.U.T. RT CL RL AMP (V) VM VM VOUT PULSE GENERATOR 90% 10% tTHL (tf ) tTLH (tr ) tTLH (tr ) tTHL (tf ) 0V AMP (V) 90% POSITIVE PULSE VM VM 10% Test Circuit for Totem-Pole Outputs DEFINITIONS: RL = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. CL = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. RT = Termination resistance should be equal to ZOUT of pulse generators. 90% 10% tw 0V Input Pulse Definition INPUT PULSE REQUIREMENTS family amplitude VM 74F 3.0V 1.5V rep. rate 1MHz tw tTLH tTHL 500ns 2.5ns 2.5ns SF00006 1996 Jan 05 5 Philips Semiconductors Product specification Dual 4-line to 1-line multiplexer 74F153 DIP16: plastic dual in-line package; 16 leads (300 mil) 1996 Jan 05 6 SOT38-4 Philips Semiconductors Product specification Dual 4-line to 1-line multiplexer 74F153 SO16: plastic small outline package; 16 leads; body width 3.9 mm 1996 Jan 05 7 SOT109-1 Philips Semiconductors Product specification Dual 4-line to 1-line multiplexer 74F153 Data sheet status Data sheet status Product status Definition [1] Objective specification Development This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. Preliminary specification Qualification This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. [1] Please consult the most recently issued datasheet before initiating or completing a design. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 Date of release: 03-98 Document order number: 1996 Jan 05 8 9397-750-05081