NCP502, NCV502 80 mA CMOS Low Iq, Low-Dropout Voltage Regulator The NCP502 series of fixed output linear regulators are designed for handheld communication equipment and portable battery powered applications which require low quiescent. The NCP502 series features an ultra−low quiescent current of 40 A. Each device contains a voltage reference unit, an error amplifier, a PMOS power transistor, resistors for setting output voltage, current limit, and temperature limit protection circuits. The NCP502 has been designed to be used with low cost ceramic capacitors. The device is housed in the micro−miniature SC70−5 and TSOP−5 surface mount packages. Standard voltage versions are 1.5 V, 1.8 V, 2.5 V, 2.7 V, 2.8 V, 2.9 V, 3.0 V, 3.1 V, 3.3 V, 3.4 V, 3.5 V, 3.6 V, 3.7 V and 5.0 V. Other voltages are available in 100 mV steps. • • • MARKING DIAGRAM 4 12 Low Quiescent Current of 40 A Typical Excellent Line and Load Regulation Low Output Voltage Option Output Voltage Accuracy of 2.0% Industrial Temperature Range of −40°C to 85°C, NCV502, TA = −40°C to 125°C NCP502: 1.3 V Enable Threshold High, 0.3 V Enable Threshold Low NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable These are Pb−Free Devices 1 5 SC70−5 SQ SUFFIX CASE 419A 5 5 Features • • • • • www.onsemi.com 3 xxx MG G 1 TSOP−5 (SOT23−5, SC59−5) SN SUFFIX CASE 483 5 xxx AYWG G 1 xxx = Specific Device Code A = Assembly Location Y = Year W = Work Week M = Date Code G = Pb−Free Package (Note: Microdot may be in either location) PIN CONNECTIONS Vin 1 GND 2 Enable 3 5 Vout 4 N/C Typical Applications • • • • Cellular Phones Battery Powered Consumer Products Hand−Held Instruments Camcorders and Cameras (Top View) ORDERING INFORMATION Battery or Unregulated Voltage Vout C1 + 1 5 + 2 ON 3 See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. C2 4 OFF This device contains 86 active transistors Figure 1. Typical Application Diagram © Semiconductor Components Industries, LLC, 2016 December, 2016 − Rev. 21 1 Publication Order Number: NCP502/D NCP502, NCV502 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ PIN FUNCTION DESCRIPTION Pin No. Pin Name 1 Vin Description 2 GND 3 Enable 4 N/C No internal connection. 5 Vout Regulated output voltage. Positive power supply input voltage. Power supply ground. This input is used to place the device into low−power standby. When this input is pulled low, the device is disabled. If this function is not used, Enable should be connected to Vin. MAXIMUM RATINGS ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Rating Symbol Value Unit Vin 12 V Enable Voltage Enable −0.3 to Vin +0.3 V Output Voltage Vout −0.3 to Vin +0.3 V Power Dissipation and Thermal Characteristics Power Dissipation PD Internally Limited W Operating Junction Temperature TJ +150 °C TA −40 to +85 −40 to +125 °C Tstg −55 to +150 °C Input Voltage Operating Ambient Temperature NCP502 NCV502 Storage Temperature Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Latchup capability (85°C) ±100 mA DC with trigger voltage. THERMAL CHARACTERISTICS Rating Symbol Thermal Characteristics, TSOP−5 (Note 2) Thermal Resistance, Junction−to−Air (Note 3) RJA Thermal Resistance, Junction−to−Ambient, SC70−5 RJA Test Conditions 1 oz Copper Thickness, 100 mm2 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ NOTE: Value ÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁ 205 400 Single component mounted on a 80 x 80 x 15 mm FR4 PCB with stated copper head spreading area. Using the following boundary conditions as stated in EIA/JESD 51−1, 2, 3, 7, 12. 2. True no connect. Printed circuit board traces are allowable. 3. This device series contains ESD protection and exceeds the following tests: Human Body Model 2000 V per MIL−STD−883, Method 3015. Machine Model Method 200 V.. www.onsemi.com 2 Unit °C/W W °C/W NCP502, NCV502 ELECTRICAL CHARACTERISTICS (Vin = Vout(nom.) + 2.0 V, Venable = Vin, Cin = 1.0 F, Cout = 1.0 F, TJ = 25°C, unless otherwise noted.) Symbol Characteristic Output Voltage (TA = 25°C, Iout = 10 mA) Vin = Vout (nom.) +1.0 V 1.5 V 1.8 V 2.5 V 2.7 V 2.8 V 2.9 V 3.0 V 3.1 V 3.3 V 3.4 V 3.5 V 3.6 V 3.7 V 5.0 V Vout Output Voltage (TA = Tlow to Thigh, Iout = 10 mA) Vin = Vout (nom.) 1.5 V 1.8 V 2.5 V 2.7 V 2.8 V 2.9 V 3.0 V 3.1 V 3.3 V 3.4 V 3.5 V 3.6 V 3.7 V 5.0 V Vout Min Typ Max 1.455 1.746 2.425 2.646 2.744 2.842 2.94 3.038 3.234 3.332 3.43 3.528 3.626 4.900 1.5 1.8 2.5 2.7 2.8 2.9 3.0 3.1 3.3 3.4 3.5 3.6 3.7 5.0 1.545 1.854 2.575 2.754 2.856 2.958 3.06 3.162 3.366 3.468 3.57 3.672 3.774 5.100 1.455 1.746 2.425 2.619 2.716 2.813 2.910 3.007 3.201 3.298 3.43 3.528 3.626 4.900 1.5 1.8 2.5 2.7 2.8 2.9 3.0 3.1 3.3 3.4 3.5 3.6 3.7 5.0 1.545 1.854 2.575 2.781 2.884 2.987 3.09 3.193 3.399 3.502 3.57 3.672 3.774 5.100 Unit V V Line Regulation (Vin = Vout + 1.0 V to 12 V, Iout = 10 mA) Regline − 0.4 3.0 mV/V Load Regulation (Iout = 1.0 mA to 80 mA) Regload − 0.2 0.8 mV/mA Output Current (Vout = (Vout at Iout = 80 mA) −3%) Io(nom.) 80 180 − mA Dropout Voltage (TA = Tlow to Thigh, Iout = 80 mA, Measured at Vout −3.0%) 1.5 V−1.7 V 1.8 V−2.4 V 2.5 V−2.6 V 2.7 V−2.9 V 3.0 V−4.0 V 4.1 V−5.0 V NCV502 − 5.0 V Vin−Vout Quiescent Current (Enable Input = 0 V) (Enable Input = Vin, Iout = 1.0 mA to Io(nom.)) mV − − − − − − − 1500 1300 1000 850 850 600 700 1900 1700 1400 1300 1200 900 1100 − − 0.1 40 1.0 90 A IQ Output Short Circuit Current (Vout = 0 V) Iout(max) 90 200 500 Ripple Rejection (f = 1.0 kHz, 15 mA) RR − 55 − dB Output Voltage Noise (f = 100 Hz to 100 kHz) Vn − 180 − Vrms 1.3 − − − − 0.3 − 100 − Enable Input Threshold Voltage (NCP502) (Voltage Increasing, Output Turns On, Logic High) (Voltage Decreasing, Output Turns Off, Logic Low) Vth(en) Output Voltage Temperature Coefficient TC V 4. Maximum package power dissipation limits must be observed. T *TA PD + J(max) RJA 5. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. www.onsemi.com 3 mA ppm/°C NCP502, NCV502 45 VOUT = 3.0 V 40 IQ, QUIESCENT CURRENT (A) IQ, QUIESCENT CURRENT (A) 45 35 30 25 20 15 10 5 40 37.5 35 32.5 30 −60 0 1 IOUT, OUTPUT CURRENT (mA) 4 3 5 6 7 −40 −20 0 40 20 60 80 100 T, TEMPERATURE (°C) Figure 2. Quiescent Current versus Input Voltage Figure 3. Quiescent Current versus Temperature 6 VIN = 4.0 V to 5.0 V 5 4 60 ENABLE VOLTAGE (V) VIN, INPUT VOLTAGE (V) 10 VIN = 4.0 V VENABLE = 0 to 4.0 V 5 0 COUT = 1.0 F IOUT = 30 mA VOUT, OUTPUT VOLTAGE (V) 40 20 0 −20 −40 0 10 20 30 40 50 60 70 80 90 3.0 2.0 IOUT = 30 mA COUT = 1.0 F 1.0 0 0 100 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 t, TIME (s) t, TIME (ms) Figure 4. Line Transient Response Figure 5. Enable Response 60 0.9 1.0 70 30 0 100 OUTPUT VOLTAGE DEVIATION (mV) 2 RIPPLE REJECTION (dB) OUTPUT VOLTAGE DEVIATION (mV) VIN, INPUT VOLTAGE (V) 0 VIN = 5.0 V VOUT = 3.0 V 42.5 COUT = 1.0 F VOUT = 3.0 V VIN = 4.0 V 50 0 −50 −100 0 50 100 150 200 250 300 350 400 450 60 50 40 30 20 0.01 VIN = 4.5 V + 0.5 VP−P VOUT = 3.0 V IOUT = 30 mA COUT = 1.0 F 0.1 1.0 10 t, TIME (s) FREQUENCY (kHz) Figure 6. Load Transient Response Figure 7. Ripple Rejection/Frequency www.onsemi.com 4 100 NCP502, NCV502 2.995 VIN = 12 V VOUT, OUTPUT VOLTAGE (V) IOUT = 10 mA 2.99 2.985 VIN = 4.0 V 2.98 2.975 2.97 2.965 2.96 −60 −40 0 −20 20 40 80 60 100 T, TEMPERATURE (°C) Figure 8. Output Voltage versus Temperature VOUT, OUTPUT VOLTAGE (V) 3.5 CIN = 1.0 F COUT = 1.0 F VENABLE = VIN 3 2.5 2 1.5 1 0.5 0 0 1 2 3 4 6 5 VIN, INPUT VOLTAGE (V) Figure 9. Output Voltage versus Input Voltage VIN − VOUT, DROPOUT VOLTAGE (mV) 1200 1000 80 mA LOAD 800 600 40 mA LOAD 400 200 10 mA LOAD 0 −50 −25 0 50 25 75 100 125 T, TEMPERATURE (°C) Figure 10. Dropout Voltage versus Temperature www.onsemi.com 5 NCP502, NCV502 DEFINITIONS Load Regulation Line Regulation The change in output voltage for a change in output current at a constant temperature. The change in output voltage for a change in input voltage. The measurement is made under conditions of low dissipation or by using pulse technique such that the average chip temperature is not significantly affected. Dropout Voltage The input/output differential at which the regulator output no longer maintains regulation against further reductions in input voltage. Measured when the output drops 3.0% below its nominal. The junction temperature, load current, and minimum input supply requirements affect the dropout level. Line Transient Response Typical over and undershoot response when input voltage is excited with a given slope. Thermal Protection Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event that the maximum junction temperature is exceeded. When activated at typically 160°C, the regulator turns off. This feature is provided to prevent failures from accidental overheating. Maximum Power Dissipation The maximum total dissipation for which the regulator will operate within its specifications. Quiescent Current The quiescent current is the current which flows through the ground when the LDO operates without a load on its output: internal IC operation, bias, etc. When the LDO becomes loaded, this term is called the Ground current. It is actually the difference between the input current (measured through the LDO input pin) and the output current. Maximum Package Power Dissipation The maximum power package dissipation is the power dissipation level at which the junction temperature reaches its maximum operating value, i.e. 125°C. Depending on the ambient power dissipation and thus the maximum available output current. APPLICATIONS INFORMATION A typical application circuit for the NCP502 series is shown in Figure 1, front page. threshold are covered in the electrical specification section of this data sheet. If the enable is not used then the pin should be connected to Vin. Input Decoupling (C1) A 1.0 F capacitor either ceramic or tantalum is recommended and should be connected close to the NCP502 package. Higher values and lower ESR will improve the overall line transient response. If large line or load transients are not expected, then it is possible to operate the regulator without the use of a capacitor. TDK capacitor: C2012X5R1C105K, or C1608X5R1A105K Hints Please be sure the Vin and GND lines are sufficiently wide. When the impedance of these lines is high, there is a chance to pick up noise or cause the regulator to malfunction. Set external components, especially the output capacitor, as close as possible to the circuit, and make leads as short as possible. Output Decoupling (C2) The NCP502 is a stable regulator and does not require any specific Equivalent Series Resistance (ESR) or a minimum output current. Capacitors exhibiting ESRs ranging from a few m up to 5.0 can thus safely be used. The minimum decoupling value is 1.0 F and can be augmented to fulfill stringent load transient requirements. The regulator accepts ceramic chip capacitors as well as tantalum devices. Larger values improve noise rejection and load regulation transient response. TDK capacitor: C2012X5R1C105K, C1608X5R1A105K, or C3216X7R1C105K Thermal As power across the NCP502 increases, it might become necessary to provide some thermal relief. The maximum power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material and also the ambient temperature effect the rate of temperature rise for the part. This is stating that when the NCP502 has good thermal conductivity through the PCB, the junction temperature will be relatively low with high power dissipation applications. Enable Operation The enable pin will turn on the regulator when pulled high and turn off the regulator when pulled low. These limits of www.onsemi.com 6 NCP502, NCV502 Ptot + ƪVin * Ignd (Iout)ƫ ) [Vin * Vout] * Iout The maximum dissipation the package can handle is given by: or T *TA PD + J(max) RJA P ) Vout * Iout VinMAX + tot Ignd ) Iout If junction temperature is not allowed above the maximum 125°C, then the NCP502 can dissipate up to 250 mW @ 25°C. The power dissipated by the NCP502 can be calculated from the following equation: If an 80 mA output current is needed then the ground current from the data sheet is 40A. For an NCP502 (3.0 V), the maximum input voltage will then be 6.12 V. ORDERING INFORMATION Nominal Output Voltage Marking NCP502SQ15T2G 1.5 LCC NCP502SQ18T2G 1.8 LCD NCP502SQ25T2G 2.5 LCE NCP502SQ27T2G 2.7 LCF NCP502SQ28T2G 2.8 LCG NCP502SQ29T2G 2.9 LJI NCP502SQ30T2G 3.0 LCH NCP502SQ31T2G 3.1 LJJ NCP502SQ33T2G 3.3 LCI NCP502SQ34T2G 3.4 LJK NCP502SQ35T2G 3.5 LGO NCP502SQ36T2G 3.6 LIU NCP502SQ37T2G 3.7 LJQ NCP502SQ50T2G 5.0 LCJ NCP502SN28T1G 2.8 LKD NCP502SN29T1G 2.9 LJN NCP502SN30T1G 3.0 LKE NCP502SN31T1G 3.1 LJO NCP502SN33T1G 3.3 LKF NCV502SN33T1G* 3.3 LKF NCP502SN34T1G 3.4 LJK NCP502SN35T1G 3.5 LJ6 NCP502SN36T1G 3.6 AC4 NCP502SN37T1G 3.7 LKC NCP502SN50T1G 5.0 LKG NCV502SN50T1G* 5.0 LKG Device Package Shipping† SC70−5 (Pb−Free) 3000 / Tape & Reel TSOP−5 (Pb−Free) 3000 / Tape & Reel Additional voltages in 100 mV steps are available upon request by contacting your ON Semiconductor representative. †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable. www.onsemi.com 7 NCP502, NCV502 PACKAGE DIMENSIONS SC−88A (SC−70−5/SOT−353) SQ SUFFIX CASE 419A−02 ISSUE L A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A−01 OBSOLETE. NEW STANDARD 419A−02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. G 5 4 −B− S 1 2 DIM A B C D G H J K N S 3 0.2 (0.008) D 5 PL B M M N J C K H SOLDER FOOTPRINT 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 www.onsemi.com 8 SCALE 20:1 mm Ǔ ǒinches INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 NCP502, NCV502 PACKAGE DIMENSIONS TSOP−5 SN SUFFIX CASE 483−02 ISSUE M NOTE 5 2X D NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIMENSION A. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. 5X 0.20 C A B 0.10 T M 2X 0.20 T B 5 1 4 2 S 3 K B DETAIL Z G A A TOP VIEW DIM A B C D G H J K M S DETAIL Z J C 0.05 H SIDE VIEW C SEATING PLANE END VIEW MILLIMETERS MIN MAX 2.85 3.15 1.35 1.65 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 0_ 10 _ 2.50 3.00 SOLDERING FOOTPRINT* 0.95 0.037 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] ◊ N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 9 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP502/D