NICHIA NCSU034B

NICHIA STS-DA1-2396A <Cat.No.120518>
NICHIA CORPORATION
SPECIFICATIONS FOR UV LED
NCSU034B(T)
● Pb-free Reflow Soldering Application
● Built-in ESD Protection Device
● RoHS Compliant
NICHIA STS-DA1-2396A <Cat.No.120518>
SPECIFICATIONS
(1) Absolute Maximum Ratings
Symbol
Absolute Maximum Rating
Unit
Forward Current
Item
IF
700
mA
Pulse Forward Current
IFP
1000
mA
Allowable Reverse Current
IR
85
mA
Power Dissipation
PD
3.01
W
Operating Temperature
Topr
-10~85
°C
Storage Temperature
Tstg
-40~100
°C
Junction Temperature
TJ
130
°C
* Absolute Maximum Ratings at TS=25°C.
* IFP conditions with pulse width ≤10ms and duty cycle ≤10%.
(2) Initial Electrical/Optical Characteristics
Item
Symbol
Condition
Typ
Unit
VF
IF=500mA
3.7
V
Radiant Flux
Φe
IF=500mA
400
mW
Peak Wavelength
λp
IF=500mA
385
nm
Δλ
IF=500mA
10
nm
Forward Voltage
Spectrum Half Width
* Characteristics at TS=25°C.
* Radiant Flux value as per CIE 127:2007 standard.
* For stabilizing the LED characteristics, it is recommended to operate at greater than 10% nominal current.
1
NICHIA STS-DA1-2396A <Cat.No.120518>
RANKS
Item
Forward Voltage
Radiant Flux
Peak Wavelength
Rank
Min
Max
H
3.9
4.3
M
3.5
3.9
L
3.1
3.5
P11
430
470
P10
390
430
P9
350
390
Uc
380
390
Unit
V
mW
nm
* Ranking at TS=25°C.
* Tolerance of measurements of the Forward Voltage is ±0.05V.
* Tolerance of measurements of the Radiant Flux is ±10%.
* Tolerance of measurements of the Peak Wavelength is ±3nm.
* A shipment shall consist of LEDs in a combination of the above ranks.
The percentage of each rank in the shipment shall be determined by Nichia.
2
NICHIA STS-DA1-2396A <Cat.No.120518>
OUTLINE DIMENSIONS
* 本製品はRoHS指令に適合しております。
This product complies with RoHS Directive.
管理番号 No.
NCSU034B
STS-DA7-2620
6.8
(単位 Unit:±0.2)
mm)
(単位 Unit: mm, 公差 Tolerance:
0.65
4.35
6.8
0.65
2.1
6.6
ダイヒートシンク
Die Heat Sink
Cathode Mark
Cathode
K
2.8
4.2
6.6
Anode
項目 Item
内容 Description
パッケージ材質
Package Materials
セラミックス
Ceramics
ガラス窓材質
Glass Materials
硬質ガラス/コバール
Hard Glass/Kovar
電極材質
Electrodes Materials
金メッキ
Au-plated
ダイヒートシンク材質
Die Heat Sink
Materials
金メッキ
Au-plated
質量
Weight
0.29g(TYP)
A
保護素子
Protection Device
3
NICHIA STS-DA1-2396A <Cat.No.120518>
SOLDERING
• Recommended Reflow Soldering Condition(Lead-free Solder)
1 to 5°C per sec
260°C Max
10sec Max
Pre-heat
180 to 200°C
60sec Max
Above 220°C
120sec Max
● Recommended Soldering Pad Pattern
8.4
4.2
7
8.4
2.8
(単位 Unit: mm)
Die Heat Sink
* This LED is designed to be reflow soldered on to a PCB. If dip soldered or hand soldered,
Nichia cannot guarantee its reliability.
* Reflow soldering must not be performed more than twice.
* Avoid rapid cooling. Ramp down the temperature gradually from the peak temperature.
* Nitrogen reflow soldering is recommended. Air flow soldering conditions can cause optical degradation,
caused by heat and/or atmosphere.
* Repairing should not be done after the LEDs have been soldered.
It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
* The Die Heat Sink should be soldered to customer PCB.
If it is difficult or impossible, use high heat-dissipating adhesive.
* When soldering, do not apply stress to the LED while the LED is hot.
4
NICHIA STS-DA1-2396A <Cat.No.120518>
PACKAGING - BULK
シリカゲルとともにICパックをアルミ防湿袋に入れ、熱シールにより封をします。
Anti-static IC packs are shipped with desiccants
in heat-sealed moisture-proof bags.
ICパック
anti-static IC Pack bag
シリカゲル
Desiccants
管理番号 No.
Nxxxxxxx
STS-DA7-1108A
ラベル Label
UV LED
TYPE Nxxxxxxx
*******
LOT YMxxxx-RRR
QTY.
PCS
RoHS
熱シール
Seal
NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
警告ラベル Warning and Explanatory Labels
アルミ防湿袋
Moisture-proof bag
LE
LED 放射
D
ビームを直接見たり触れたり
UV LED
LED
LED RADIATION
RADIATION
AVOID
EXPOSURE
TO
AVOID
EXPOSURE
TO BEAM
ビームを直接見たり触れたり
しないこと
しないこと
E
クラス3B
クラス3B LLED製品
D 製品
BEAM
3B
T
PRODUC
CLAS 3B LED PRODUCT
LED
CLASS
S
アルミ防湿袋を並べて入れ、間隔にはクッション材を詰めます。
Moisture-proof bags are packed in cardboard boxes
with shock absorbing materials to fill empty spaces.
ラベル Label
UV LED
TYPE Nxxxxxxx
*******
RANK RRR
QTY.
PCS
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Nichia
LED
* 客先型名を*******で示します。
客先型名が設定されていない場合は空白です。
******* is the customer part number.
If not provided, it is not indicated on the label.
* ロット表記方法についてはロット番号の項を
参照して下さい。
For details, see "LOT NUMBERING SCHEME"
in this document.
* 本製品はICパックに入れたのち、輸送の衝撃から保護するためダンボールで梱包します。
Products shipped in anti-static IC packs are packed in a moisture-proof bag.
They are shipped in cardboard boxes to protect them from external forces during transportation.
* 取り扱いに際して、落下させたり、強い衝撃を与えたりしますと、製品を損傷させる原因になりますので注意して下さい。
Do not drop or shock the box. It may damage the products.
* ダンボールには防水加工がされておりませんので、梱包箱が水に濡れないよう注意して下さい。
Do not expose to water, the box is not water-resistant.
* 輸送、運搬に際して弊社よりの梱包状態あるいは同等の梱包を行って下さい。
Using an original packaging material or equivalent in transit is recommended.
5
NICHIA STS-DA1-2396A <Cat.No.120518>
TAPE AND REEL DIMENSIONS
テーピング部 Tape
1.75±0.1
12
Φ1.5+0.1
-0
2±0.054±0.1
Nxxx034x
STS-DA7-2675
管理番号 No.
0.29±0.1
(単位 Unit: mm)
Φ1.5+0.25
-0
7.15±0.1
12+0.3
-0.1
5.5±0.05
Cathode
2.5±0.1
エンボスキャリアテープ
Embossed Carrier Tape
7.15±0.1
トレーラ部/リーダ部 Trailer and Leader
トップカバーテープ
Top Cover Tape
引き出し方向
Feed
Direction
トレーラ部最小160mm(空部)
Trailer 160mm MIN(Empty Pockets)
LED装着部
Loaded Pockets
引き出し部最小100mm(空部)
Leader with Top Cover Tape
100mm MIN(Empty Pocket)
リーダ部最小400mm
Leader without Top Cover Tape 400mm MIN
リール部 Reel
180+0
-3
15.4±1
13+1
-0
* 数量は1リールにつき 500個入りです。
Reel Size: 500pcs
Φ
* JIS C 0806電子部品テーピングに準拠しています。
±
21
ラベル
Label
Φ
13 ±
0
.2
Φ60+1
-0
8
0.
The tape packing method complies with JIS C 0806
(Packaging of Electronic Components on Continuous Tapes).
6
NICHIA STS-DA1-2396A <Cat.No.120518>
PACKAGING - TAPE & REEL
シリカゲルとともにリールをアルミ防湿袋に入れ、熱シールにより封をします。
Reels are shipped with desiccants in heat-sealed moisture-proof bags.
シリカゲル
Desiccants
リール
Reel
管理番号 No.
Nxxxxxxx
STS-DA7-1109A
ラベル Label
UV LED
TYPE Nxxxxxxx
*******
LOT YMxxxx-RRR
QTY.
PCS
RoHS
熱シール
Seal
NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
警告ラベル Warning and Explanatory Labels
アルミ防湿袋
Moisture-proof Bag
LE
LED 放射
D
ビームを直接見たり触れたり
UV LED
LED
LED RADIATION
RADIATION
AVOID
EXPOSURE
TO
AVOID
EXPOSURE
TO BEAM
ビームを直接見たり触れたり
しないこと
しないこと
E
クラス3B
クラス3B LLED製品
D 製品
BEAM
3B
T
PRODUC
CLAS 3B LED PRODUCT
LED
CLASS
S
アルミ防湿袋を並べて入れ、ダンボールで仕切ります。
Moisture-proof bags are packed in cardboard boxes
with corrugated partitions.
ラベル Label
UV LED
TYPE Nxxxxxxx
*******
RANK RRR
QTY.
PCS
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Nichia
LED
* 客先型名を*******で示します。
客先型名が設定されていない場合は空白です。
******* is the customer part number.
If not provided, it is not indicated on the label.
* ロット表記方法についてはロット番号の項を
参照して下さい。
For details, see "LOT NUMBERING SCHEME"
in this document.
* 本製品はテーピングしたのち、輸送の衝撃から保護するためダンボールで梱包します。
Products shipped on tape and reel are packed in a moisture-proof bag.
They are shipped in cardboard boxes to protect them from external forces during transportation.
* 取り扱いに際して、落下させたり、強い衝撃を与えたりしますと、製品を損傷させる原因になりますので注意して下さい。
Do not drop or shock the box. It may damage the products.
* ダンボールには防水加工がされておりませんので、梱包箱が水に濡れないよう注意して下さい。
Do not expose to water, the box is not water-resistant.
* 輸送、運搬に際して弊社よりの梱包状態あるいは同等の梱包を行って下さい。
Using an original packaging material or equivalent in transit is recommended.
7
NICHIA STS-DA1-2396A <Cat.No.120518>
LOT NUMBERING SCHEME
Lot Number is presented by using the following alphanumeric code.
YMxxxx - RRR
Y - Year
Year
Y
2009
9
2010
A
2011
B
2012
C
2013
D
2014
E
M - Month
Month
M
Month
M
1
1
7
7
2
2
8
8
3
3
9
9
4
4
10
A
5
5
11
B
6
6
12
C
xxxx-Nichia's Product Number
RRR-Ranking by Wavelength, Ranking by Radiant Flux, Ranking by Forward Voltage
8
NICHIA STS-DA1-2396A <Cat.No.120518>
DERATING CHARACTERISTICS
管理番号 No.
周囲温度-許容順電流特性
Ambient Temperature vs
Allowable Forward Current
Derating1
カソード側はんだ接合部温度-許容順電流特性
Solder Temperature(Cathode Side) vs
Allowable Forward Cu rrent
RθJA =35°C/W
Derating2
1000
800
(25, 700)
許容順電流
600
400
(85, 300)
200
Allowable Forward Current(mA)
許容順電流
1000
Allowable Forward Current(mA)
NCSU034B
STS-DA7-2592
800
(85, 700)
600
400
200
0
0
0
20
40
60
80
100
120
0
20
40
60
80
100
周囲温度
カソード側はんだ接合部温度
Ambient Temperature(°C)
Solder Temperature(Cathode Side)(°C)
デューティー比-許容順電流特性
Duty Ratio vs
Allowable Forward Current
Duty
120
TA=25°C
許容順電流
Allowable Forward Current(mA)
10000
1000
700
100
1
10
100
デューティー比
Duty Ratio(%)
9
NICHIA STS-DA1-2396A <Cat.No.120518>
OPTICAL CHARACTERISTICS
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
管理番号 No.
発光スペクトル
Spectrum
NCSU034B
STS-DA7-2593
T A=25°C
IFP=500mA
Spectrum
1.0
相対発光強度
Relative Emission Intensity(a.u.)
0.8
0.6
0.4
0.2
0.0
300
350
400
450
500
550
600
波長
Wavelength(nm)
Directivity1
指向特性
Directivity
T A=25°C
IFP=500mA
-10°
0°
-20°
10°
20°
30°
-30°
40°
放射角度
Radiation Angle
-40°
50°
-50°
-60°
60°
-70°
70°
80°
-80°
-90°
90°
1
0.5
0
0.5
1
相対放射強度
Relative Radiant Intensity(a.u.)
10
NICHIA STS-DA1-2396A <Cat.No.120518>
FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
順電圧-順電流特性
Forward Voltage vs
Forward Current
周囲温度-順電圧特性
Ambient Temperature vs
Forward Voltage
VfIf
T A=25°C
1000
NCSU034B
STS-DA7-2594
TaVf
IFP=500mA
5.0
500
4.5
順電圧
Forward Voltage(V)
順電流
Forward Current(mA)
管理番号 No.
100
4.0
3.5
3.0
10
2.5
2.5
3.0
3.5
4.0
4.5
5.0
-60 -40 -20
順電圧
Forward Voltage(V)
20
40
60
80
100 120
周囲温度
Ambient Temperature(°C)
周囲温度-相対放射束特性
順電流-相対放射束特性
Forward Current vs
Relative Radiant Flu x
Ambient Temperature vs
Relative Radiant Flux
IfIv
T A=25°C
2.5
TaIv
IFP= 500mA
1.4
2.0
相対放射束
Relative Radiant Flux(a.u.)
相対放射束
Relative Radiant Flux(a.u.)
0
1.5
1.0
1.2
1.0
0.8
0.5
0.6
0.0
0
200
400
600
800
順電流
Forward Current(mA)
1000
1200
-60 -40 -20
0
20
40
60
80
100 120
周囲温度
Ambient Temperature(°C)
11
NICHIA STS-DA1-2396A <Cat.No.120518>
FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
順電流-ピーク波長特性
Forward Current vs
Peak Wavelength
管理番号 No.
NCSU034B
STS-DA7-2595
T A=25°C
IfλD
391
ピーク波長
Peak Wavelength(nm)
389
387
385
383
381
379
10
100
1000
順電流
Forward Current(mA)
周囲温度-ピーク波長特性
Ambient Temperature vs
Peak Wavelength
IFP= 500mA
TaλD
391
ピーク波長
Peak Wavelength(nm)
389
387
385
383
381
379
-60 -40 -20
0
20
40
60
80
100 120
周囲温度
Ambient Temperature(°C)
12
NICHIA STS-DA1-2396A <Cat.No.120518>
RELIABILITY
(1) Tests and Results
Reference
Test
Test
Test Conditions
Standard
Duration
Failure
Criteria
#
Units
Failed/Tested
Resistance to
Tsld=260°C, 10sec, 2reflows
Soldering Heat
#1
0/10
100cycles
#1
0/10
TA=100°C
1000hours
#1
0/10
TA=-40°C
1000hours
#1
0/10
TA=25°C, IF=500mA
1000hours
#1
0/10
TA=25°C, IF=700mA
1000hours
#1
0/10
TA=85°C, IF=300mA
1000hours
#1
0/10
60°C, RH=90%, IF=450mA
500hours
#1
0/10
TA=-10°C, IF=500mA
1000hours
#1
0/10
48minutes
#1
0/10
#1
0/10
(Reflow Soldering)
Temperature Cycle
JEITA ED-4701
-40°C(30min)~25°C(5min)~
100 105
100°C(30min)~25°C(5min)
High Temperature
JEITA ED-4701
Storage
200 201
Low Temperature
JEITA ED-4701
Storage
200 202
Room Temperature
Operating Life
Condition 1
Room Temperature
Operating Life
Condition 2
High Temperature
Operating Life
Temperature Humidity
Operating Life
Low Temperature
Operating Life
Vibration
Electrostatic Discharges
JEITA ED-4701
200m/s2, 100~2000~100Hz,
400 403
4cycles, 4min, each X, Y, Z
JEITA ED-4701
HBM, 2kV, 1.5kΩ, 100pF, 3pulses,
300 304
alternately positive or negative
NOTES:
1) RθJA≈35°C/W
2) Measurements are performed after allowing the LEDs to return to room temperature.
(2) Failure Criteria
Criteria #
#1
Items
Conditions
Failure Criteria
Forward Voltage(VF)
IF=500mA
>Initial value×1.1
Radiant Flux(ΦE)
IF=500mA
<Initial value×0.7
13
NICHIA STS-DA1-2396A <Cat.No.120518>
CAUTIONS
(1) Storage
Conditions
Storage
Temperature
Before Opening Aluminum Bag
≤30°C
Humidity
≤90%RH
Time
Within 1 Year from Delivery Date
● Absorbed moisture in LED packages can vaporize and expand during soldering, which can cause interface delamination
and result in optical performance degradation. Products are packed in moisture-proof aluminum bags
to minimize moisture absorption during transportation and storage.
Included silica gel desiccants change from blue to red if moisture had penetrated bags.
● Although the leads or electrode pads (anode and cathode) of the product are plated with gold,
prolonged exposure to a corrosive environment might cause the gold plated the leads or electrode pads to tarnish,
and thus leading to difficulties in soldering. If unused LEDs remain, they must be stored in a hermetically sealed container.
Nichia recommends using the original moisture-proof bag for storage.
● Do not use sulfur-containing materials in commercial products. Some materials, such as seals and adhesives, may contain sulfur.
The contaminated plating of LEDs might cause an open circuit. Silicone rubber is recommended as a material for seals.
Bear in mind, the use of silicones may lead to silicone contamination of electrical contacts inside the products,
caused by low molecular weight volatile siloxane.
● To prevent water condensation, please avoid large temperature and humidity fluctuations for the storage conditions.
(2) Directions for Use
● When designing a circuit, the current through each LED must not exceed the Absolute Maximum Rating.
Operating at a constant current per LED is recommended. In case of operating at a constant voltage, Circuit B is recommended.
If the LEDs are operated with constant voltage using Circuit A, the current through the LEDs may vary due to the variation
in Forward Voltage characteristics of the LEDs.
(A)
(B)
...
...
● LEDs should be operated in forward bias. Driving circuits must not subject LEDs to either forward or reverse voltage while off.
Continuous reverse voltage can cause migration and LED damage.
● For stabilizing the LED characteristics, it is recommended to operate at greater than 10% nominal current.
● For outdoor use, necessary measures should be taken to prevent water, moisture and salt air damage.
● This LED also emits visible light. Please take notice of visible light spectrum,
in case you use this LED as light source of sensors etc.
(3) Handling Precautions
● Do not handle LEDs with bare hands, it may contaminate the LED surface and affect optical characteristics.
In the worst case, catastrophic failure from excess pressure through wire-bond breaks and package damage may result.
● When handling the product with tweezers, be careful not to apply excessive force to the resin.
Otherwise, The resin can be cut, chipped, delaminate or deformed, causing wire-bond breaks and catastrophic failures.
● Dropping the product may cause damage.
● Do not stack assembled PCBs together. Failure to comply can cause the resin portion of the product to be cut, chipped,
delaminated and/or deformed. It may cause wire to break, leading to catastrophic failures.
14
NICHIA STS-DA1-2396A <Cat.No.120518>
(4) Design Consideration
● Although Nichia recommends using a copper PCB for this product, customer is advised to verify the PCB with the products
before use. Stress during soldering can cause the glass lens to break and/or the solder joints to crack.
● PCB warpage after mounting the products onto a PCB can cause the package to break.
The LED should be placed in a way to minimize the stress on the LEDs due to PCB bow and twist.
● The position and orientation of the LEDs affect how much mechanical stress is exerted on the LEDs placed near the score lines.
The LED should be placed in a way to minimize the stress on the LEDs due to board flexing.
● Board separation must be performed using special jigs, not using hands.
● If an aluminum PCB is used, customer is advised to verity the PCB with the products before use.
Thermal stress during use can cause the solder joints to crack.
(5) Electrostatic Discharge (ESD)
● The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability.
When handling the products, the following measures against electrostatic discharge are strongly recommended:
Eliminating the charge
Grounded wriststrap, ESD footwear, clothes, and floors
Grounded workstation equipment and tools
ESD table/shelf mat made of conductive materials
● Proper grounding is required for all devices, equipment, and machinery used in product assembly.
Surge protection should be considered when designing of commercial products.
● If tools or equipment contain insulating materials such as glass or plastic,
the following measures against electrostatic discharge are strongly recommended:
Dissipating static charge with conductive materials
Preventing charge generation with moisture
Neutralizing the charge with ionizers
● The customer is advised to check if the LEDs are damaged by ESD
when performing the characteristics inspection of the LEDs in the application.
Damage can be detected with a forward voltage measurement at low current (≤1mA).
● ESD damaged LEDs may have current flow at a low voltage.
Failure Criteria: VF<2.0V at IF=0.5mA
(6) Thermal Management
● Proper thermal management is an important when designing products with LEDs. LED die temperature is affected
by PCB thermal resistance and LED spacing on the board. Please design products in a way that the LED die temperature
does not exceed the maximum Junction Temperature (TJ).
● Drive current should be determined for the surrounding ambient temperature (TA) to dissipate the heat from the product.
● The following equations can be used to calculate the junction temperature of the products.
1) TJ=TA+RθJA・W
2) TJ=TS+RθJS・W
*TJ=LED junction temperature: °C
TA=Ambient temperature: °C
TS=Soldering temperature (cathode side): °C
RθJA=Thermal resistance from junction to ambient: °C/W
RθJS=Thermal resistance from junction to TS measuring point≈7°C/W
W=Input power(IF×VF): W
Ts Point
15
NICHIA STS-DA1-2396A <Cat.No.120518>
(7) Cleaning
● The LEDs should not be cleaned. Other cleaning agents except for Freon solvent should be tested prior
to use whether they will not affect the package and the glass. Please note that Freon solvent is prohibited worldwide.
● Ultrasonic cleaning is not recommended since it may have adverse effects on the LEDs
depending on the ultrasonic power and how LED is assembled.
If ultrasonic cleaning must be used, the customer is advised to make sure the LEDs will not be damaged prior to cleaning.
(8) Eye Safety
● In 2006, the International Electrical Commission (IEC) published IEC 62471:2006 Photobiological safety of lamps
and lamp systems, which added LEDs in its scope.
On the other hand, the IEC 60825-1:2007 laser safety standard removed LEDs from its scope.
However, please be advised that some countries and regions have adopted standards
based on the IEC laser safety standard IEC 60825-1:20112001, which still includes LEDs in its scope.
Most of Nichia's LEDs can be classified as belonging into either the Exempt Group or Risk Group 1.
High-power LEDs, that emit light containing blue wavelengths, may be classified as Risk Group 2.
Please proceed with caution when viewing directly any LEDs driven at high current, or viewing LEDs
with optical instruments which may greatly increase the damages to your eyes.
● Viewing a flashing light may cause eye discomfort. When incorporating the LED into your product,
please be careful to avoid adverse effects on the human body caused by light stimulation.
● The products are UV light LEDs, and radiate intense UV light during operation. Since UV light can be harmful to eyes,
do NOT look directly into the UV light, even through an optical instrument. In case of the light reflection,
UV protective glasses are required to use in order to avoid damage by the light.
(9) Others
● The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment,
communications equipment, measurement instruments and household appliances).
Consult Nichia's sales staff in advance for information on the applications in which exceptional quality
and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or
health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control system, automobiles,
traffic control equipment, life support systems and safety devices).
● The customer shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent
from Nichia. When defective LEDs are found, the customer shall inform Nichia directly before disassembling or analysis.
● Both the customers and Nichia will agree on official specifications of supplied products before a customer's volume production.
● Specifications and appearance subject to change for improvement without notice.
16