INTEGRATED CIRCUITS NE/SA/SE532 LM258/358/A/2904 Low power dual operational amplifiers Product data Supersedes data of 2002 Jan 22 2002 Jul 12 Philips Semiconductors Product data NE/SA/SE532/ LM258/358/A/2904 Low power dual operational amplifiers DESCRIPTION PIN CONFIGURATION The 532/358/LM2904 consists of two independent, high gain, internally frequency-compensated operational amplifiers internally frequency-compensated operational amplifiers designed specifically to operate from a single power supply over a wide range of voltages. Operation from dual power supplies is also possible, and the low power supply current drain is independent of the magnitude of the power supply voltage. D, DP, and N Packages OUTPUT A 1 INVERTING INPUT A 2 NON INVERTING INPUT A 3 V– 4 A –+ B +– 8 V+ 7 OUTPUT B 6 INVERTING INPUT B 5 NON INVERTING INPUT B UNIQUE FEATURES In the linear mode the input common-mode voltage range includes ground and the output voltage can also swing to includes ground and the output voltage can also swing to ground, even though operated from only a single power supply voltage. The unity gain cross frequency is temperature-compensated. The input bias current is also temperature-compensated. SL00282 Figure 1. Pin configuration. FEATURES • Internally frequency-compensated for unity gain • Large DC voltage gain: 100 dB • Wide bandwidth (unity gain): 1 MHz (temperature-compensated) • Wide power supply range single supply: 3 VDC to 30 VDC, or dual supplies: ±1.5 VDC to ±15 VDC • Very low supply current drain (400 µA)—essentially independent of supply voltage (1 mW/op amp at +5 VDC) • Low input biasing current: 45 nADC temperature-compensated • Low input offset voltage: 2 mVDC, and offset current: 5nADC • Differential input voltage range equal to the power supply voltage • Large output voltage: 0 VDC to V+ 1.5 VDC swing EQUIVALENT CIRCUIT V+ 6 µA 6 µA 100 µA Q5 Q6 CC Q7 Q2 RSC Q3 OUTPUT – Q1 Q4 INPUTS Q11 Q13 + Q10 Q12 50 µA Q8 Q9 SL00283 Figure 2. Equivalent circuit. 2002 Jul 12 2 853-1241 28616 Philips Semiconductors Product data NE/SA/SE532/ LM258/358/A/2904 Low power dual operational amplifiers ORDERING INFORMATION DESCRIPTION TEMPERATURE RANGE ORDER CODE DWG # 8-Pin Plastic Small Outline (SO) Package 0 °C to +70 °C NE532D SOT96-1 8-Pin Plastic Dual In-Line Package (DIP) 0 °C to +70 °C NE532N SOT97-1 8-Pin Plastic Small Outline (SO) Package –40 °C to +85 °C SA532D SOT96-1 8-Pin Plastic Small Outline (SO) Package –40 °C to +125 °C LM2904D SOT96-1 8-Pin Plastic Thin Shrink Small Outline Package (TSSOP) –40 °C to +125 °C LM2904DP SOT505-1 8-Pin Plastic Dual In-Line Package (DIP) –40 °C to +125 °C LM2904N SOT97-1 8-Pin Plastic Small Outline (SO) Package –25 °C to +125 °C LM258D SOT96-1 8-Pin Plastic Dual In-Line Package (DIP) –25 °C to +125 °C LM258N SOT97-1 8-Pin Plastic Small Outline (SO) Package 0 °C to +70 °C LM358D SOT96-1 8-Pin Plastic Thin Shrink Small Outline Package (TSSOP) 0 °C to +70 °C LM358DP SOT505-1 8-Pin Plastic Dual In-Line Package (DIP) 0 °C to +70 °C LM358N SOT97-1 8-Pin Plastic Small Outline (SO) Package 0 °C to +70 °C LM358AD SOT96-1 8-Pin Plastic Dual In-Line Package (DIP) 0 °C to +70 °C LM358AN SOT97-1 8-Pin Plastic Dual In-Line Package (DIP) –55 °C to +125 °C SE532N SOT97-1 ABSOLUTE MAXIMUM RATINGS SYMBOL VS PARAMETER Supply voltage, V+ Differential input voltage VIN Input voltage PD Maximum power dissipation Tamb = 25 °C (Still air)1 N package D package DP package RATING UNIT 32 or ±16 VDC 32 VDC –0.3 to +32 VDC 1160 780 714 mW mW mW Output short-circuit to GND2 V+ < 15 VDC and Tamb = 25 °C Continuous Tamb Operating ambient temperature range NE532/LM358/LM358A LM258 LM2904 SA532 SE532 0 to +70 –25 to +85 –40 to +125 –40 to +85 –55 to +125 °C °C °C °C °C Tstg Storage temperature range –65 to +150 °C Tsld Lead soldering temperature (10 sec max) 230 °C NOTE: 1. Derate above 25 °C, at the following rates: N package at 9.3 mW/°C D package at 6.2 mW/°C DP package at 5.72 mW/°C 2. Short-circuits from the output to V+ can cause excessive heating and eventual destruction. The maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15 VDC, continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. 2002 Jul 12 3 Philips Semiconductors Product data NE/SA/SE532/ LM258/358/A/2904 Low power dual operational amplifiers DC ELECTRICAL CHARACTERISTICS Tamb = 25 °C; V+ = +5 V, unless otherwise specified. PARAMETER SYMBOL Min VOS Offset voltage1 VOS Drift IOS Offset current IOS Drift NE/SA532/ LM358/LM2904 SE532, LM258 TEST CONDITIONS RS = 0 Ω Typ Max ±2 ±5 RS = 0 Ω; over temp. Min Max ±2 ±7 mV ±9 mV ±7 RS = 0 Ω; over temp. 7 IIN(+) – IIN(–) ±3 ±5 ±100 Over temp. µV/°C 7 ±30 UNIT Typ ±50 nA ±150 nA Over temp. 10 IIN(+) or IIN(–) 45 150 10 45 250 pA/°C 300 40 500 nA IBIAS S Input current2 IIN(+) or IIN(–); Over temp. 40 IB Drift Over temp. 50 VCM C Common-mode voltage g range3 V+ = 30 V 0 V+–1.5 0 V+–1.5 V V+ = 30 V; Over temp. 0 V+–2.0 0 V+–2.0 V CMRR Common-mode rejection ratio V+ = 30 V 70 VOH O Output voltage swing RL ≥ 2 kΩ; V+ = 30 V; over temp. 26 RL ≥ 10 kΩ; V+ = 30 V; over temp. 27 VOL Output voltage swing 26 28 27 V 28 V 20 5 20 mV 1.0 0.5 1.0 mA RL=∞ on all amplifiers; V+ = 30 V; over temp. 0.6 1.2 0.6 1.2 mA RL ≥ 2 kΩ; VOUT ±10 V 50 V+=15V (for large VO swing); over temp. 25 PSRR Supply voltage rejection ratio RS = 0 Ω 65 ISC dB 5 Large-signal voltage gain Output current (Sink) 70 0.5 AVOL IOUT 65 RL = ∞; V+ = 30 V Supply current Output current (Source) 85 nA pA/°C RL ≥ 10 kΩ; over temp. ICC Amplifier-to-amplifier coupling4 50 f = 1 kHz to 20 kHz (input referred) 100 25 100 V/mV 15 100 65 –120 V/mV 100 dB –120 dB VIN+ = +1 VDC; VIN– = 0 VDC; V+ = 15 VDC 20 40 20 40 mA VIN+ = +1 VDC; VIN– = 0 VDC; V+ = 15 VDC; over temp. 10 20 10 20 mA VIN– = +1 VDC; VIN+ = 0 VDC; V+ = 15 VDC 10 20 10 20 mA VIN– = +1 VDC; VIN+ = 0 VDC; V+ = 15 VDC; over temp. 5 8 5 8 mA VIN+ = 0 V; VIN– = +1 VDC; VO = 200 mV 12 50 12 50 µA Short circuit current5 40 Differential input voltage6 60 40 V+ 60 mA V+ V GBW Unity gain bandwidth Tamb = 25 °C 1 1 MHz SR Slew rate Tamb = 25 °C 0.3 0.3 V/µs VNOISE Input noise voltage Tamb = 25 °C; f = 1 kHz 40 40 nV/√Hz (Notes on next page). 2002 Jul 12 4 Philips Semiconductors Product data NE/SA/SE532/ LM258/358/A/2904 Low power dual operational amplifiers DC ELECTRICAL CHARACTERISTICS (continued) Tamb = 25 °C; V+ = +5 V; unless otherwise specified. SYMBOL PARAMETER VOS Offset voltage1 VOS Drift IOS Offset current IOS Drift IBIAS S Input current2 IB Drift VCM C Common mode voltage range3 Common-mode CMRR Common-mode rejection ratio VOH O Output voltage swing VOL Output voltage swing ICC Supply current AVOL O Large signal voltage gain Large-signal PSRR Supply voltage rejection ratio Amplifier-to-amplifier coupling4 Output current (Source) IOUT Output current (Sink) ISC TEST CONDITIONS LM358A Min RS = 0 Ω Typ Max ±2 ±3 RS = 0 Ω; over temp. UNIT mV ±5 mV RS = 0 Ω; over temp. 7 20 µV/°C IIN(+) – IIN(–) 5 ±30 nA ±75 nA Over temp. 10 300 pA/°C nA Over temp. IIN(+) or IIN(–) 45 100 IIN(+) or IIN(–); Over temp. 40 200 Over temp. 50 nA pA/°C V+ = 30 V 0 V+–1.5 V+ = 30 V; Over temp. 0 V+–2.0 V+ = 30 V 65 RL ≥ 2 kΩ; V+ = 30 V; over temp. 26 RL ≥ 10 kΩ; V+ = 30 V; over temp. 27 85 V V dB V 28 V RL ≥ 10 kΩ; over temp. 5 20 mV RL = ∞, V+ = 30 V 0.5 1.0 mA RL = ∞ on all amplifiers; V+ = 30 V; over temp. 0.6 1.2 mA RL ≥ 2 kΩ; VOUT ±10 V 25 V+ = 15 V (for large VO swing); over temp. 15 RS = 0 Ω 65 f=1kHz to 20kHz (input referred) 100 V/mV V/mV 100 dB –120 dB VIN+ = +1 VDC; VIN– = 0 VDC; V+ = 15 VDC 20 40 mA VIN+ = +1 VDC; VIN– = 0 VDC; V+ = 15 VDC; over temp. 10 20 mA VIN– = +1 VDC,;VIN+ = 0 VDC; V+ = 15 VDC 10 20 mA VIN– = +1 VDC; VIN+ = 0 VDC;V+ = 15 VDC; over temp. 5 8 mA VIN+ = 0 V; VIN– = +1 VDC; VO = 200 mV 12 50 Short circuit current5 40 Differential input voltage6 µA 60 V+ mA V GBW Unity gain bandwidth Tamb = 25 °C 1 MHz SR Slew rate Tamb = 25 °C 0.3 V/µs VNOISE Input noise voltage Tamb = 25 °C; f = 1 kHz 40 nV/√Hz NOTES: 1. VO ≈ 1.4 V, RS = 0 Ω with V+ from 5 V to 30 V; and over the full input common-mode range (0 V to V+ –1.5 V). 2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so no loading change exists on the input lines. 3. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the common-mode voltage range is V+ –1.5 V, but either or both inputs can go to +32 V without damage. 4. Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be detected as this type of capacitance coupling increases at higher frequencies. 5. Short-circuits from the output to V+ can cause excessive heating and eventual destruction. The maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15 VDC, continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. 6. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the common-mode voltage range is V+ –1.5 V, but either or both inputs can go to +32 VDC without damage. 2002 Jul 12 5 Philips Semiconductors Product data NE/SA/SE532/ LM258/358/A/2904 Low power dual operational amplifiers TYPICAL PERFORMANCE CHARACTERISTICS Supply Current Current Limiting 2 Tamb = 0 °C to +125 °C Tamb = 55 °C 10 20 60 50 40 30 20 30 VO 80 V+ = 30 VDC AND –55 °C ≤ Tamb ≤ +125 °C 40 V+ = 10 to 15 VDC AND –55 °C < Tamb < +125 °C 20 0 10 100 1k 10k 85 105 125 0 10 15 100 kΩ +7 VDC 10 100k 1M 10M VO – + VIN 2 kΩ 10k FREQUENCY (Hz) 4 RL < 2 kΩ V+ 15 VDC 3 2 1 100k 1M 3 2 1 0 0 10 20 10 θIN 400 INPUT 350 OUTPUT 300 250 0 2 3 4 5 t — TIME (µs) 6 7 7 +V+ /2 6 V2 + 5 – IO 4 INDEPENDENT OF V+ TAamb= +25 °C 3 2 Tamb = +25 °C V+ = +30 VDC 1 VO – OUTPUT VOLTAGE (VDC ) V∆ – OUTPUT VOLTAGE REFERENCE TO V+ (VDDC ) EO – OUTPUT VOLTAGE (mV) V+ EO 50 pF 8 40 Output Characteristics Current Sinking 8 450 30 TIME (µs) Output Characteristics Current Sourcing 500 40 Voltage-Follower Response FREQUENCY (Hz) Voltage-Follower Pulse Response (Small-Signal) 30 0 5 1k 20 SUPPLY VOLTAGE (VDC) VDC 1K 0 1 45 65 20 V+/2 60 25 Large-Signal Frequency Response – + VIN 100 5 TEMPERATURE (°C) VO — OUTPUT SWING (V p–p ) 120 40 0 55 35 –15 10M 0.1 µf 80 0 40 Open-Loop Frequency Response V+ RL + 2 kΩ 10 SUPPLY VOLTAGE (VDC) 140 RL + 20 kΩ 120 OUTPUT VOLTAGE (V) 0 70 INPOUT VOLTAGE (V) 1 AVOL — VOLTAGE GAIN (dB) 80 3 0 VOLTAGE GAIN (dB) Voltage Gain 160 90 OUTPUT CURRENT (mADC) SUPPLY CURRENT DRAIN (mADC ) 4 V+ = +5 VDC V+ = +15 VDC V+ = +30 VDC 1 V+ V+ /2 – 0.1 + VO IO Tamb = +25 °C 1 0.001 IO+ 0.01 0.1 1 10 100 – OUTPUT SOURCE CURRENT (mADC) 0.01 0.001 0.01 0.1 1 10 100 IO – OUTPUT SINK CURRENT (mADC) SL00284 Figure 3. Typical performance characteristics. 2002 Jul 12 6 Philips Semiconductors Product data NE/SA/SE532/ LM258/358/A/2904 Low power dual operational amplifiers Input Voltage Range Input Current 15 90 VCM = 0 VDC I B – INPUT CURRENT (nA DC ) +V IN — INPUT VOLTAGE ( +VDC) 80 10 NEGATIVE POSITIVE 5 0 5 10 15 70 V+ = +30 VDC 60 50 V+ = +15 VDC 40 30 V+ = +5 VDC 20 10 0 –55 –35 –15 V+ OR V– — POWER SUPPLY VOLTAGE (+ VDC) 5 25 45 65 85 105 125 CMRR — COMMON–MODE REJECTION RATIO (dB) TYPICAL PERFORMANCE CHARACTERISTICS (Continued) Common–Mode Rejection Ratio 120 100 80 +7.5 VDC 100 kΩ 60 100 Ω 40 VO – + 100 Ω + VIN 100 kΩ 20 7.5 VDC 0 1k 100 Tamb — TEMPERATURE (°C) 10k 100k f — FREQUENCY (Hz) 1M SL00285 Figure 4. Typical performance characteristics (continued). TYPICAL APPLICATIONS V+ RF V+ 8 RIN VIN 10 kΩ V+ – VO + 8 V+ 4 VIN 2 RL – + 10 kΩ V+ BLOCKS DC. GAIN 2 R1 VO 4 RF Single Supply Inverting Amplifier V+ Input Biasing Voltage Follower V+ 10 kΩ 8 – VIN VO + 4 10 kΩ Non-Inverting Amplifier SL00286 Figure 5. Typical applications. 2002 Jul 12 7 Philips Semiconductors Product data NE/SA/SE532/ LM258/358/A/2904 Low power dual operational amplifiers SO8: plastic small outline package; 8 leads; body width 3.9 mm 2002 Jul 12 8 SOT96-1 Philips Semiconductors Product data NE/SA/SE532/ LM258/358/A/2904 Low power dual operational amplifiers DIP8: plastic dual in-line package; 8 leads (300 mil) 2002 Jul 12 9 SOT97-1 Philips Semiconductors Product data NE/SA/SE532/ LM258/358/A/2904 Low power dual operational amplifiers TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm 2002 Jul 12 10 SOT505-1 Philips Semiconductors Product data NE/SA/SE532/ LM258/358/A/2904 Low power dual operational amplifiers NOTES 2002 Jul 12 11 Philips Semiconductors Product data NE/SA/SE532/ LM258/358/A/2904 Low power dual operational amplifiers Data sheet status Data sheet status [1] Product status [2] Definitions Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A. [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Koninklijke Philips Electronics N.V. 2002 All rights reserved. Printed in U.S.A. Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 Date of release: 08-02 For sales offices addresses send e-mail to: [email protected]. 2002 Jul 12 Document order number: 12 9397 750 10187