Hirose NX-25T-F3 I/o card interface connector Datasheet

I/O Card Interface Connectors
NX Series
3. ESD Secure
Thermoplastic molded covers assures insulation
of the connections and shields from ESD.
4. Secure Latching
A built-in latch assures correct and secure
mating of connector.
5. Reliable Conductor Termination
Reliable termination of conductors
accomplished by proven IDC termination.
is
6. Sequential Mating
The 0.8mm pitch contacts are engaging the
corresponding parts in sequence: GroundPower & Signal
7. Rugged Construction
Securely attached to the board with optional
screws.
■Features
1. Low Profile
Protorusion above the PCB board is only 2.9mm, and the
connectors can be mounted to type I and II I/O cards.
2. EMI/RFI protection
Full metal shielding. Shield connects first, ahead of
contacts.
8. Card Frame Kits
Available as a separate part number.
9. Secure Attachment to Frame Kit.
Compliant mounting bracket attaches the
connectore directly to the frame kit.
■Applications
Used with I/O cards, portable personal computers,and the external connections of various small-sized portable
terminals.
■Specifications
Current rating 0.5 A
Ratings
Voltage rating 125 V AC
Item
Operating temperature
-30ç to +70ç (Note 1) Storage temperature range -10ç to +60ç (Note 2)
Operating humidity
95% R.H. or less
(No condensation)
Storage humidity range
Specification
40 to 70% (Note 2)
Conditions
1. Insulation resistance
250 M ohms min.
100 V DC
2. Withstanding voltage
No flashover or insulation breakdown.
300 V AC / 1 minute
3. Contact resistance
40 m ohms max.
100 mA
4. Vibration
No electrical discontinuity of 10µs or
more
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm,
2 hours in each of the 3 directions.
5. Humidity (Steady state) Insulation resistance: 100 M ohms min.
96 hours at temperature of 60ç and humidity of 90% to 95%
6. Temperature cycle
No damage, cracks, or parts looseness.
-55ç, 30 min./15 to 30ç, within 5 min/85ç, 30 min
/15 to 35ç, within 5 min, for 5 cycles
7. Durability
(Insertion/withdrawal)
60 m ohms max.
3000 cycles
8. Resistance to
Soldering heat
No deformation of components affecting Reflow: At the recommended temperature profile
performance.
Manual soldering: 300ç for 3 seconds
Note 1: Includes temperature rise caused by current flow.
Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature
Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during
transportation.
B8
■Materials
BApplicable Cable
Item
Material
Insulator
Receptacle Contacts
Plug unit
Plug cover
Finish
Thermoplastic Compound
Black
UL94V-0
Copper alloy
Selective gold plating
----
Body
Stain less
Solder Plating
----
Insulator
Thermoplastic Compound
Black
----
Contacts
Copper alloy
Selective gold plating UL94V-0
Cover
Thermoplastic Compound
Black
Body
Stainless Steel
Frame
Thermoplastic Compound
I/O cable
AWG # 28(7/0.127)
Conductor size
Jacket outer
diameter
0.58mm
0.62mm
Cable style
UL20276 and
UL2789
UL2990
---UL94V-0
-
Frame ground
Phosphor bronze
terminal
Frame kit
Remarks
Black
----
Gold Plating
----
Spring pin
Stainless steel
-
----
Coil spring
Stainless steel
-
----
Panel
Stainless steel
With thermal
adhesive tape
■Ordering Information
----
Serise name : NX
Termination style
●Receptacle
30 : IDC termination (for fine wire)
NX 60 T A - 15 S AA 9 - SP
1
2
3
5
11
6
7
8
9
60 : SMT type
Lock
T : Inner lock
●Plug
Applicable Conductor
NX 30 T A - 15 P AA
1
2
3
4
5
6
7
Number of contacts : 9, 15, 25, 32
Connector type
P : Plug
●Plug Covers
S : Receptacle
Polarizing
AA : AA type
NX - 15 T A - CV
1
A : AWG #28
5
3
11
Offset
10
9 : 0.9 mm
3 : 0.3 mm
None : On Board Type
(Dimension from connector center line to the surface of the PCB)
●Frame Kits
Variations
NX - 15 T - KT 9 (05)
1
5
3
10
8
12
SP : Compliant mounting bracket(for cards use) SH : Through hole
Types of accessories
CV : Vertical opening cover case
●Panel (For 9, 15, or 25 contacts)
KT : Frame kit
NX T - P (05)
1
3
10
K : Frame
12
P : Panel (For Type2card)
PA : Panel (For Type1card)
(For 32 contacts)
BS : Bushing
NX - 32 T - P (05)
1
5
CV1 : Vertical opening cover case(Thin 5 mm thinclness type)
3
10
12
CSA : Coil spring
CSB : Coil spring
Serial number by type
Panel finish
No symbol : Silver matt finish
(05) : Dull Processing material
B9
BDimensions of Connector Cross Section
●0.9 mm offset type
●0.3 mm offset type
BRecommended Board Dimensions
(Board Thickness: 0.5 mm Maximum)
Unit: mm
B10
Part Number
CL No.
Number of contacts
A
B
C
D
offset
NX-09T-KT9
234-0010-8
09
26.4
25.0
22.4
06.4
0.9
NX-15T-KT9
234-0011-0
15
31.2
29.8
27.2
11.2
0.9
NX-25T-KT9
234-0012-3
25
39.2
37.8
35.2
19.2
0.9
NX-32T-KT9
234-0026-8
32
44.8
43.4
40.8
24.8
0.9
NX-09T-KT3
234-0034-6
09
26.4
25.0
22.4
06.4
0.3
NX-15T-KT3
234-0035-9
15
31.2
29.8
27.2
11.2
0.3
NX-25T-KT3
234-0036-1
25
39.2
37.8
35.2
19.2
0.3
NX-32T-KT3
234-0054-3
32
44.8
43.4
40.8
24.8
0.3
■Receptacle
●0.9 mm offset type
D
P=0.8
Contact No.1
2
•
2
8
1.9
0.3
A
NX60TA-✽ SAA9-SP
B
Ø1
2.9
0.9
C
Unit: mm
Part Number
CL No.
Number of contacts
A
B
C
D
NX60TA-09SAA9-SP
234-0106-5
09
25.2
19.7
17.2
06.4
NX60TB-15SAA9-SP
234-0097-6
15
30.0
24.5
22.0
11.2
NX60TA-25SAA9-SP
234-0107-8
25
38.0
32.5
30.0
19.2
NX60T0-32SAA9-SP
234-0023-0
32
43.6
38.1
35.6
24.8
●0.3 mm offset type
Contact No.1
NX60TA-✽ SAA3-SP
Unit: mm
Part Number
CL No.
Number of contacts
A
B
C
D
NX60TA-09SAA3-SP
234-0031-8
09
25.2
19.7
17.2
06.4
NX60TB-15SAA3-SP
234-0098-9
15
30.0
24.5
22.0
11.2
NX60TA-25SAA3-SP
234-0033-3
25
38.0
32.5
30.0
19.2
NX60TA-32SAA3-SP
234-0053-0
32
43.6
38.1
35.6
24.8
B11
■Plug units
NX30TA-15PAA
CL234-0005-8
Contact No.1
Unit: mm
Part Number
CL No.
Number of contacts
A
B
NX30TA-09PAA
234-0002-0
09
14.6
14.1
NX30TA-15PAA
234-0005-8
15
19.4
18.9
NX30TA-25PAA
234-0008-6
25
27.4
26.9
NX30TA-32PAA
234-0024-2
32
33.0
32.5
■Plug Covers
NX-15T-CV
CL234-0006-0
Unit: mm
Part Number
CL No.
Number of contacts
A
B
C
D
E
F
G
Outer diameter of cable
NX-09T-CV
234-0003-2
09
18.2 21.2 14.0 26 06.0 5.5
6.5
less than Ø 5.5
NX-15T-CV
234-0006-0
15
23.0 26.0 18.8 28 07.0 6.0
7.0
less than Ø 6.0
NX-15T-CV1
234-0017-7
15
23.0 26.0 18.8 28 05.0 4.0
5.0
less than Ø 4.0
NX-25T-CV
234-0009-9
25
31.0 34.0 26.8 30 08.0 6.5
7.5
less than Ø 6.5
NX-25TA-CV1
234-0039-0
25
31.0 34.0 26.8 32 13.0 4.0
5.0
less than Ø 6.5(Note)
NX-32TA-CV1
234-0025-5
32
36.6 40.6 32.4 32 16.2 4.2 5.0
less than Ø 7.5(Note)
Note: Designed for flat cable use. when round cable is used, clamp portion shall be made flat, adjusting exclusive use bushing.
B12
Frame
■Frame kit
■(Frame + 2 X Cover Panels)
Cover
NX-15T-KT9
CL234-0011-0
Unit: mm
Connectors for the card Side(Note 1)
Part Number
CL No.
Number of contacts
NX-09T-KT9
234-0010-8
09
NX-15T-KT9
234-0011-0
15
NX-25T-KT9
234-0012-3
25
NX-32T-KT9
234-0026-8
32
NX60TA-32SAA9-SP
NX-09T-KT3
234-0034-6
09
NX60TA-09SAA3-SP
NX-15T-KT3
234-0035-9
15
NX-25T-KT3
234-0036-1
25
NX-32T-KT3
234-0054-3
32
CL No.
Part Number
Offset
Back Connector
NX60TA-09SAA9-SP
IC1F-68RD-1.27SFA
IC1F-68RD-1.27SFA
640-0040-3
640-0035-3
0.9mm
0.3mm
NX60TB-15SAA9-SP
NX60TA-25SAA9-SP
NX60TB-15SAA3-SP
NX60TA-25SAA3-SP
NX60TA-32SAA3-SP
■Frame only
NX-15T-F9
CL234-0019-2
Unit: mm
Part Number
CL No.
Number of contacts Connectors for the card Side
Back Connector
Panel
NX-09T-F9
234-0018-0
09
NX-15T-F9
234-0019-2
15
NX-25T-F9
234-0020-1
25
NX-32T-F9
234-0063-4
32
NX60TA-32SAA9-SP NX-32T-P
NX-09T-F3
234-0060-6
09
NX60TA-09SAA3-SP
NX-15T-F3
234-0061-9
15
NX-25T-F3
234-0062-1
25
NX-32T-F3
234-0067-5
32
Coil Spring
Offset
NX-CSA
0.9mm
NX60TA-09SAA9-SP
IC1F-68RD-1.27SFA
IC1F-68RD-1.27SFA
NX60TB-15SAA9-SP NXT-P
NX60TA-25SAA9-SP
NX60TB-15SAA3-SP NXT-P
NX60TA-25SAA3-SP
NX60TA-32SAA3-SP NX-32T-P
NX-CSA
&
0.3mm
NX-CSB
B13
2PCMCIA cards)
■Panel (for type2
NXT-P
CL234-0058-4
Unit: mm
Part Number
CL No.
NXT-P
234-0058-4
NXT-P(05)
234-0058-4-05
NX-32T-P
234-0059-7
NX-32T-P(05)
234-0059-7-05
Number of Frame contacts
9, 15, 25
32
Panel Finish
Silver matt finish
Dull processing material
Silver matt finish
Dull processing material
1PCMCIA cards)
■Panel (for type1
NXT-PA
CL234-2011-1
Part Number
CL No.
NXT-PA
234-2011-1
NXT-PA(05)
234-2011-1-05
NX-32T-PA
234-0068-8
Number of Frame contacts
9, 15, 25
32
Panel Finish
Silver matt finish
Dull processing material
Silver matt finish
Dull processing material
NX-32T-PA(05)
234-0068-8-05
✽ Panels are avilable in two types: a 32-contact special type and a common type with 9, 15, or 25 contacts.
✽ Ordering volume for panels is one panel per unit volume.One frame corresponds to 2 panels.
B14
■Ground contact spring
■Bushing
NX-CSA
CL234-0042-4
Part Number
CL No.
NX-32T-BS
CL234-0055-6
Offset: Ordering Volume
Part Number
CL No.
Number of contacts
NX-25T-BS
234-0074-0
25
NX-32T-BS
234-0055-6
32
NX-CSA
234-0042-4
0.3mm: One Pack
0.9mm: Two Packs
NX-CSB
234-0043-7
0.3mm: One Packs
Sold in package of 1000 pcs.
For 1,000 frames of 0.9 offset, please order two packs of NX-CSA.
For 1,000 frames of 0.3 offset, please order one pack of NX-CSA
and one pack of NX-CSB.
Applications for Connections of I/O Card Connectors
■Modular plugs for round cable (AWG #28) connector
No. of contacts
6 Contacts
Modular Plug
Manual Wiring Tool
Part Number
CL No.
Part Number
CL No.
6
TM30P-66P
222-2684-2
TC1-TM30P-66P
250-0145-6
8
TM30P-88P
222-2685-5
TC1-TM30P-88P
250-0146-9
8 Contacts
■8-Contact adapter
Lead Number Reference Table
TM5RL-88-JJ
CL222-3798-7
Connector (a) Contact number TM5RL-88 1
2
3
4
5
6
7
8
Connector (b) Contact number TM5RL-88 1
2
3
4
5
6
7
8
B15
BPlug Termination Tool
●Fixtures
Cable wiring cradle
NX/3230-CAT
CL902-0250-4
Cutting and IDC termination
Fixture main unit
NX/3230-HP
CL902-0252-0
Cutting and IDC termination
attachment fixtures
NX30TA-9GP
CL902-0253-2
NX30TA-15GP
CL902-0254-5
NX30TA-25GP
CL902-0255-8
NX30TA-32GP
CL902-0257-3
●Wiring Procedure
B16
➀
➁
➂
1. Set the wires in the wiring
fixtures.
2. Align holding plates (A) and
(B).
3. Arrange the wires one at a time
through holding plates (A) and
(B).
➅
➄
➃
4. Set holding plates (A) and (B)
onto the guide plate.
5. Insert the guide plate into the
pressure welding and cutting
fixtures.
6. Pull down the handle. The
wiring and cutting of excess
cable length are completed.
B Frame Kit Fixture
Ground spring press fitting fixture
Special blocks
A frame kit thermal fixture and a cooling fixture are also available.
B Wiring Fixture and Accessories List
Plug
Process
Cable
I/O Cable
Discrete cable
Connector
Wiring
Pressurs Welding and Cutting
Press
Guide Plate
Shield Case Caulking
Cover Case
Hand Tool
Hood Fitting
NX-30TA-9HC
NX30TA-09PAA
NX30TA-09GP NX-09T-CV0
NX30TA-32PAA
NX30TA-32GP NX-32T-CV1 Screw Fixing
CL902-0260-8
NX-30TA-15HC
NX-15T-CV0
NX/3230-CAT
CL902-0261-0
NX30TA-15GP
NX30TA-15PAA
NX-30TA-15HC1 Manual Work
(All contacts NX/3230-HP
NX-15T-CV1
CL902-0262-3
common)
NX-30TA-25HC1
NX30TA-25GP NX-25T-CV
NX30TA-25PAA
CL902-0263-6
Note 1: The caulking height of hand tool is defined by follwing cable specifications.
Note 2: Caulking specification change is needed when special cable is used.
Cable Diameter
Strand Termination
NX-9T-CV
Cover Case
Ø 5.1±0.2
Fold the shield and bind 1.5 times with copper tape.
NX-15T-CV
Ø 5.7±0.2
Do,
NX-25T-CV
Ø 6.5±0.2
Do,
NX-15T-CV1
Ø 3.8±0.2
Crimp with cable sheath directly.
Frame Kit
Process
Frame Kit
Spring Pin Press Fitting
Panel Thermal
Press
Caulking
NX-25T-KT(9•3)
NX-32T-KT(9•3)
Panel Cooling
NX-SPT-9
NX-9T-KT(9•3)
NX-15T-KT(9•3)
Unit
CL902-0275-5
NX-SPT-15
NX-SPT
CL902-0276-8
NX-PHT
NX-PCT
CL902-0274-2
NX-SPT-25
CL902-0282-0
CL902-0283-3
CL902-0277-0
NX-SPT-32
CL902-0278-3
B17
Back Connectors for Type II I/O Cards
■NX Series 68
■Features
1. Low profile
Receptacle connectors have a mounting height of 3.5
mm and can be mounted to type II I/O cards.
2. Shielded construction
A metal shell is used for shielding.
3. ESD protection
The use of an over-mold cover offers excellent ESD
protection.
4. More efficient wiring work
Wiring on the plug side uses AWG #30 pressure welding
(discrete type) for more efficient wiring work.
■Applications
■Specifications
Item
I/O card interfaces.
Specification
Conditions
1. Current rating
0.5A
----------
2. Voltage rating
125 V AC
----------
BApplicable
I/O Cable
Conductor size
AWG #30 (7/0.1)
Insulator outer diameter
0.5mm
Cable style
UL20276
Finish
Remarks
3. Insulation resistance 250 M ohms min. 100 V DC
No flashover or insulation
breakdown.
4. Withstanding voltage 300 V AC
40 m ohms min. 100 mA
5. Contact resistance
6. Durability (Insertion/withdrawal) 3000 cycles
Contact resistance : 60 m ohms max.
■Materials
Item
Material
Receptacle
Plug unit
Plug cover
Frame kit
Insulator
Synthetic resin
Color : Black
UL94V-0
Contacts
Copper alloy
Selective gold plating
----------
Body
Stainless steel
Solder plating
----------
Insulator
Synthetic resin
Color : Black
UL94V-0
Contacts
Copper alloy
Selective gold plating
----------
Cover
Synthetic resin
Color : Black
UL94V-0
Body
Stainless steel
----------
----------
Frame
Synthetic resin
Color : Black
UL94V-0
FG terminal
Phosphor bronze
Gold plating
----------
Spring pin
Stainless steel
----------
----------
Coil spring
Stainless steel
----------
----------
Panel
Stainless steel
With thermal adhesive tape
----------
■Ordering Information
●Receptacle
NX 60 H - 68 S 9 - SP
1
2
3
4
5
6
7
●Plug unit
NX 30 H - 68 P
1
2
3
4
3
Wiring style 30: Loose lead pressure welding type (for fine wire)
3
Serial type for form
4
Number of contacts: 68
5
Type of opening S: Receptacle
60: SMT type
P: Plug
NX - 68 H - CV
4
Series name:NX
2
5
●Plug cover
1
1
8
6
Coplanarity: 0.9 (Dimension from connector center to board mounting position)
7
Variations SP: Spring pin (for cards)
8
Type of accessories CV: Vertical opening cover
●Frame kit
NX - 68 H - KT 9 (05)
1
B18
4
3
8
6
9
KT: Frame kit
9
Panel finish (05): Dull processing
■Receptacle
Note 1: The signal pin SMT dimension of this product is 0+0.1
-0.05.
Note 2: Caulking specification change is needed when special cable is used.
Part Number
CL No.
NX60H-68S9-SP
234-0078-1
■Plug Unit
Part Number
CL No.
NX30H-68P
234-0079-4
B19
■Plug Cover
Part Number
CL No.
NX-68H-CV
234-0080-3
■Frame Kit
Main unit
Panel
Note 1: Suitable connectors for portion A are IC1F-68RD-1.27SFA.
Suitable connectors for portion B are NX60H-68S9-SP.
B20
Part Number
CL No.
NX-68H-KT9(05)
234-0081-6-05
BRCB mounting pattern (Applicable Board Thickness: 0.5 mm MAX)
Note 1: Applicable connectors for portion A are IC1F-68RD-1.27SFA.
Applicable connectors for portion B are NX60H-68S9-SP.
BConnector Mounting Dimensions
B21
BTemperature Profile
10s max
● Applicable Conditions
Temperature(ç)
Reflow system
: IR reflow
240
230
Solder
: Paste type 63 Sn/37 Pb
200
Test board Glass epoxy 47mm x 77.3mm x 0.5 mm
180
Metal mask thickness: 0.15 mm
(Flux content 9 wt%)
150
● Recommended temperature profile.
The temperature may be slightly changed according to
the solder paste type and amount.
0
120s max
Preheating Time
40s max
40s max
Soldering time
Time
B22
Similar pages