Nel OD-08JS18FS Precision, low power consumption, fast warm-up sc-cut ocxo in 20x20 mm through hole package Datasheet

Data Sheet 0635H
CRYSTAL OSCILLATORS
OD-X8JXXXXX
Precision, Low Power Consumption, Fast Warm-up SC-cut
OCXO in 20x20 mm Through Hole Package
Features
•
•
•
•
SC-cut crystal
Extremely Low Power Consumption (125 mW)
Fast Warm-up Time (30 s)
-8
High Stability (up to ± 1x10 )
•
•
•
•
Low Aging (5x10 /day, 5x10 /year)
Low Phase Noise (-160 dBc/Hz, TYP, floor)
Sine Wave or HCMOS/TTL output
8 MHz to 160 MHz Frequencies Available
-10
-8
Specifications:
Applications
•
•
•
•
0.42 (10,7 mm)
Ø0.018 (0,46 mm)TYP
0.800 SQ. (20,4 mm)
Telecommunication Systems
Data Communications
GPS
Battery Powered Systems and Equipment
3
4
0.600 (15.24 mm)
2
Vcc
1
5
0.600 (15,24 mm)
Vc
1
Vref 2
3
DUT
4
OUTPUT
5
10K
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: [email protected] www.nelfc.com
Data Sheet 0635H
CRYSTAL OSCILLATORS
OD-X8JXXXXX Series
Aging
Allan Variance
SSB Phase Noise
Retrace
G-sensitivity
Input Voltage
Vcc
Min
Max
Unit
-0.5
5.5
V
-40
-1
85
7
°C
V
160
MHz
ppb
ppb/V
8
vs. Temp.
vs. Supply
per day
per year
.1s to 10s
1Hz
10 Hz
100 Hz
1 KHz
10 KHz
After 30 minutes
worst direction
4.75
3.15
Typ
10.000
±50
1
5E-10
1E-7
1E-11
-90
-120
-150
-153
-160
5.0
3.3
0.125
0.35
0.5
-50
2
Note
1*
See chart below
after 30 days
5E-8 available2*
dBc/Hz
±10
±1.0
5.25
3.45
0.15
ppb
ppb/G
V
3*
See chart below to specify
steady state, 25°C
W
Standard Operating
steady state, -30°C
Temperature, for Op
start-up @ -30°C
0.7
Temp. 85 °C ad 20%
Subharmonics
-45
dBc
At Higher Frequencies
Spectral Purity
Spurious
-80
Harmonics/Sine
-35
-30
10KOhm//15pF (HCMOS/TTL), 50 Ohm (Sinewave)
Load
to 0.1ppm accuracy
30
45
s
Warm-up time
τ
3.3V HCMOS/TTL compatible or Sinewave (+7± 3) dBm
Output Waveform
Vc
0
Vref
V
Control voltage
from nominal F
±0.5
±1
ppm
Pull range
Monotonic, posit
0.4
ppm/V
Deviation slope
Vc0
@25°C, Fnom.
Vref/2-1 Vref/2 Vref/2+1
V
Setability
Environmental and Mechanical
-30°C to 70°C Standard, Other options – see chart below
Operating temp. range
Per MIL-STD-202, 30G, 11ms
Mechanical Shock
Per MIL-STD-202, 5G to 2000 Hz
Vibration
260°C for 10s Max leads only
Soldering Conditions
Electrical Connections
Pin #1-Vc ; Pin#2 – Vref; Pin #3 – Vcc; Pin #4- Output ; Pin #5- GND;
Pin Out
Power consumption
P
Condition
All parameters for 10 MHz
Parameter
Symb
Absolute Maximum Ratings
Vcc
Input Break
Down Voltage
Ts
Storage temper.
Vc
Control Voltage
Electrical
F
Frequency
Frequency stability
∆F/F
Notes:
1* Higher frequencies can be achieved either by using higher frequency crystals or by low noise analog harmonic
multiplication. Both methods have advantages and drawbacks. If lowest possible phase noise on the noise floor is most important
– high frequency crystal will be used. If phase noise close to the carrier and aging are more important – multiplication will be
used. Please consult factory for your specific requirement.
2* Aging rate is usually proportional to the operating frequency, unless higher frequency is achieved by multiplication.
Keep it in mind while specifying aging.
3* Phase noise deteriorates with frequencies going higher. If analog multiplication is used to achieve higher frequency
the phase noise roughly follows the formula of additional 20LogN, where N is a multiplication factor across entire frequency
offset range. If higher frequency is achieved by using higher frequency crystal phase noise close to the carrier deteriorates due to
the lower Q of the crystal and is usually worse, compared to multiplied solution. On the noise floor, however it remains more or
less the same. This design usually starts utilizing multiplication techniques in the range of 25 MHz to 35 MHz.
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: [email protected] www.nelfc.com
Data Sheet 0635H
CRYSTAL OSCILLATORS
OD-X8JXXXXX Series
Creating a Part Number
OD - X 8J X
XX X X
Package Code
OD
Aging
5 pin 20x20mm package
Code
L
S
Supply Voltage
Code
0
A
Specification
5V ± 5%
3.3V± 5%
Temperature Range
Output
Code
T
S
Specification
TTL
Sinewave
Specification
1x10-9/Day
5x10-10/Day
Temperature Stability
Code
17
58
28
18
YZ
Specification
1x10-7
5x10-8
2x10-8
1x10-8
Yx10-Z
Code
A
B
C
D
E
F
Specification
0°C to 50°C
-10°C to 60°C
0°C to 70°C
-20°C to 70°C
-30°C to 70°C
-40°C to 80°C
Not all combinations are available. Consult Factory.
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: [email protected] www.nelfc.com
Similar pages