Burr-Brown OPA2340PAG4 Single-supply, rail-to-rail operational amplifiers microamplifier tm sery Datasheet

®
OPA
OPA340
OPA2340
OPA4340
434
0
OPA
340
OPA
2340
OPA
434
0
SINGLE-SUPPLY, RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
MicroAmplifier ™ Series
FEATURES
APPLICATIONS
●
●
●
●
●
●
●
●
● DRIVING A/D CONVERTERS
● PCMCIA CARDS
● DATA ACQUISITION
● PROCESS CONTROL
● AUDIO PROCESSING
● COMMUNICATIONS
● ACTIVE FILTERS
● TEST EQUIPMENT
RAIL-TO-RAIL INPUT
RAIL-TO-RAIL OUTPUT (within 1mV)
MicroSIZE PACKAGES
WIDE BANDWIDTH: 5.5MHz
HIGH SLEW RATE: 6V/µs
LOW THD+NOISE: 0.0007% (f = 1kHz)
LOW QUIESCENT CURRENT: 750µA/channel
SINGLE, DUAL, AND QUAD
of the supply rails with a 100kΩ load. They offer excellent dynamic response (BW = 5.5MHz, SR = 6V/µs), yet
quiescent current is only 750µA. Dual and quad designs
feature completely independent circuitry for lowest
crosstalk and freedom from interaction.
The single (OPA340) packages are the tiny 5-lead
SOT-23-5 surface mount, SO-8 surface mount, and
8-pin DIP. The dual (OPA2340) comes in the miniature MSOP-8 surface mount, SO-8 surface mount,
and 8-pin DIP packages. The quad (OPA4340) packages are the space-saving SSOP-16 surface mount,
SO-14 surface mount, and the 14-pin DIP. All are
specified from –40°C to +85°C and operate from
–55°C to +125°C. A SPICE macromodel is available
for design analysis.
DESCRIPTION
OPA340 series rail-to-rail CMOS operational amplifiers are optimized for low voltage, single supply operation. Rail-to-rail input/output and high speed operation
make them ideal for driving sampling analog-to-digital
converters. They are also well suited for general purpose and audio applications as well as providing I/V
conversion at the output of D/A converters. Single,
dual, and quad versions have identical specifications
for design flexibility.
The OPA340 series operates on a single supply as low as
2.5V with an input common-mode voltage range that
extends 500mV below ground and 500mV above the
positive supply. Output voltage swing is to within 1mV
OPA340
OPA4340
NC
1
8
NC
–In
2
7
V+
+In
3
6
V–
4
5
OPA340
Out 1
8-Pin DIP, SO-8
5
V+
V– 2
+In 3
4
–In
SOT-23-5
16
Out D
15
–In D
14
+In D
4
13
–V
+In B
5
12
+In C
–In B
6
11
–In C
Out B
7
10
Out C
NC
8
9
NC
Out A
1
Output
–In A
2
NC
+In A
3
+V
A
OPA2340
Out A
1
–In A
2
+In A
3
V–
4
A
B
8
V+
7
Out B
6
–In B
5
+In B
8-Pin DIP, SO-8, MSOP-8
D
B
C
SSOP-16
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111
Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
®
© 1997 Burr-Brown Corporation
SBOS073
PDS-1404C
1
Printed in U.S.A. December, 1997
OPA340/2340/4340
SPECIFICATIONS: VS = 2.7V to 5V
At TA = +25°C, RL = 10kΩ connected to VS/2 and VOUT = VS/2, unless otherwise noted.
Boldface limits apply over the specified temperature range, TA = –40°C to +85°C. VS = 5V.
OPA340NA, PA, UA
OPA2340EA, PA, UA
OPA4340EA, PA, UA
PARAMETER
CONDITION
OFFSET VOLTAGE
Input Offset Voltage
vs Temperature
vs Power Supply
T A = –40°C to +85°C
Channel Separation, dc
INPUT BIAS CURRENT
Input Bias Current
TA = –40°C to +85°C
Input Offset Current
NOISE
Input Voltage Noise, f = 0.1 to 50kHz
Input Voltage Noise Density, f = 1kHz
Current Noise Density, f = 1kHz
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-Mode Rejection Ratio
VOS
dVOS/dT
PSRR
MIN
VS = 5V
VS = 2.7V to 5.5V, VCM = 0V
VS = 2.7V to 5.5V, VCM = 0V
µV
µV/°C
µV/V
µV/V
µV/V
±0.2
en
in
8
25
3
VCM
CMRR
AOL
GBW
SR
THD+N
TA = –40°C to +85°C
TEMPERATURE RANGE
Specified Range
Operating Range
Storage Range
Thermal Resistance
SOT-23-5 Surface Mount
MSOP-8 Surface Mount
SO-8 Surface Mount
8-Pin DIP
SSOP-16 Surface Mount
SO-14 Surface Mount
14-Pin DIP
±500
IOS
OUTPUT
Voltage Output Swing from Rail(3)
TA = –40°C to +85°C
POWER SUPPLY
Specified Voltage Range
Operating Voltage Range
Quiescent Current (per amplifier)
TA = –40°C to +85°C
±150
±2.5
30
±0.2
TA = –40°C to +85°C
TA = –40°C to +85°C
Short-Circuit Current
Capacitive Load Drive
UNITS
IB
TA = –40°C to +85°C
FREQUENCY RESPONSE
Gain-Bandwidth Product
Slew Rate
Settling Time, 0.1%
0.01%
Overload Recovery Time
Total Harmonic Distortion + Noise
MAX
120
120
0.2
–0.3V < VCM < (V+) –1.8V
VS = 5V, –0.3V < VCM < 5.3V
VS = 2.7V, –0.3V < VCM < 3V
–0.3
80
70
66
INPUT IMPEDANCE
Differential
Common-Mode
OPEN-LOOP GAIN
Open-Loop Voltage Gain
TA = –40°C to +85°C
TYP(1)
RL = 100kΩ, 5mV < VO < (V+) –5mV
RL = 100kΩ, 5mV < VO < (V+) –5mV
RL = 10kΩ, 50mV < VO < (V+) –50mV
RL = 10kΩ, 50mV < VO < (V+) –50mV
RL = 2kΩ, 200mV < VO < (V+) –200mV
RL = 2kΩ, 200mV < VO < (V+) –200mV
106
106
100
100
94
94
IQ
µVrms
nV/√Hz
fA/√Hz
(V+) +0.3
V
dB
dB
dB
1013 || 3
1013 || 6
Ω || pF
Ω || pF
124
dB
dB
dB
dB
dB
dB
120
114
5.5
6
1
1.6
0.2
0.0007
RL = 100kΩ, AOL ≥ 106dB
RL = 100kΩ, AOL ≥ 106dB
RL = 10kΩ, AOL ≥ 100dB
RL = 10kΩ, AOL ≥ 100dB
RL = 2kΩ, AOL ≥ 94dB
RL = 2kΩ, AOL ≥ 94dB
1
10
40
MHz
V/µs
µs
µs
µs
%
5
5
50
50
200
200
mV
mV
mV
mV
mV
mV
mA
5
950
1100
V
V
µA
µA
+85
+125
+125
°C
°C
°C
±50
See Typical Curve
ISC
CLOAD
2.7
2.5 to 5.5
750
IO = 0, VS = +5V
IO = 0, VS = +5V
–40
–55
–55
θJA
200
150
150
100
100
100
80
NOTES: (1) VS = +5V. (2) V OUT = 0.25V to 3.25V. (3) Output voltage swings are measured between the output and power supply rails.
®
OPA340/2340/4340
2
pA
pA
pA
92
84
80
G=1
VS = 5V, G = 1, CL = 100pF
VS = 5V, 2V Step, CL = 100pF
VS = 5V, 2V Step, CL = 100pF
VIN • G = VS
VS = 5V, VO = 3Vp-p(2), G = 1, f = 1kHz
VS
±10
±60
±10
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
ELECTROSTATIC
DISCHARGE SENSITIVITY
PIN CONFIGURATIONS
Top View
SOIC/DIP
OPA4340
Out A
1
–In A
2
A
14
Out D
13
–In D
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
D
+In A
3
12
+In D
V+
4
11
V–
+In B
5
10
+In C
–In B
6
9
–In C
Out B
7
8
Out C
B
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
C
ABSOLUTE MAXIMUM RATINGS(1)
Supply Voltage ................................................................................... 5.5V
Signal Input Terminals, Voltage (2) .................... (V–) –0.5V to (V+) +0.5V
Current(2) .................................................... 10mA
Output Short-Circuit(3) .............................................................. Continuous
Operating Temperature ................................................. –55°C to +125°C
Storage Temperature ..................................................... –55°C to +125°C
Junction Temperature ...................................................................... 150°C
Lead Temperature (soldering, 10s) ................................................. 300°C
NOTES: (1) Stresses above these ratings may cause permanent damage.
(2) Input terminals are diode-clamped to the power supply rails. Input signals
that can swing more than 0.5V beyond the supply rails should be currentlimited to 10mA or less. (3) Short-circuit to ground, one amplifier per
package.
PACKAGE/ORDERING INFORMATION
PRODUCT
PACKAGE
PACKAGE
DRAWING
NUMBER(1)
Single
OPA340NA
5-Lead SOT-23-5
331
–40°C to +85°C
A40
"
"
"
"
OPA340PA
OPA340UA
8-Pin DIP
SO-8 Surface-Mount
006
182
–40°C to +85°C
–40°C to +85°C
OPA340PA
OPA340UA
OPA340NA-250
OPA340NA-3K
OPA340PA
OPA340UA
Dual
OPA2340EA
"
OPA2340PA
OPA2340UA
MSOP-8 Surface-Mount
"
8-Pin DIP
SO-8 Surface-Mount
337
"
006
182
–40°C to +85°C
"
–40°C to +85°C
–40°C to +85°C
A40A
"
OPA2340PA
OPA2340UA
OPA2340EA-250
OPA2340EA-2500
OPA2340PA
OPA2340UA
Tape and Reel
Tape and Reel
Rails
Rails (3)
Quad
OPA4340EA
"
OPA4340PA
OPA4340UA
SSOP-16 Surface-Mount
"
14-Pin DIP
SO-14 Surface Mount
322
"
010
235
–40°C to +85°C
"
–40°C to +85°C
–40°C to +85°C
OPA4340EA
"
OPA4340PA
OPA4340UA
OPA4340EA-250
OPA4340EA-2500
OPA4340PA
OPA4340UA
Tape and Reel
Tape and Reel
Rails
Rails (3)
"
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER(2)
TRANSPORT
MEDIA
Tape and Reel
Tape and Reel
Rails
Rails (3)
NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) Models with -250, -2500, and
-3K are available only in Tape and Reel in the quantities indicated (e.g., -250 indicates 250 devices per reel). Ordering 3000 pieces of “OPA340NA-3K” will get
a single 3000 piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book. (3) SO-8 and SO-14
models also available in Tape and Reel.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility
for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or
licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support
devices and/or systems.
®
3
OPA340/2340/4340
TYPICAL PERFORMANCE CURVES
At TA = +25°C, VS = +5V, and RL = 10kΩ connected to VS/2, unless otherwise noted.
POWER SUPPLY and COMMON-MODE
REJECTION vs FREQUENCY
OPEN-LOOP GAIN/PHASE vs FREQUENCY
160
0
100
PSRR
140
80
–45
80
–90
60
40
Phase (°)
100
–135
20
PSRR, CMRR (dB)
Voltage Gain (dB)
120
60
40
CMRR
20
0
–180
–20
0
0.1
10
1
100
1k
10k
100k
1M
10M
1
10
100
Frequency (Hz)
1k
10k
100k
1M
Frequency (Hz)
INPUT VOLTAGE AND CURRENT NOISE
SPECTRAL DENSITY vs FREQUENCY
CHANNEL SEPARATION vs FREQUENCY
1k
10k
140
100
10
10
1
Channel Separation (dB)
100
Voltage Noise
Current Noise (fA√Hz)
Voltage Noise (nV√Hz)
Current Noise
1k
130
120
110
G = 1, All Channels
0.1
1
1
10
100
1k
10k
100k
100
1M
10
100
1k
100k
Frequency (Hz)
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
CLOSED-LOOP OUTPUT IMPEDANCE
vs FREQUENCY
0.1
5k
G = 100
RL = 600
4k
0.01
Output Resistance (Ω)
RL = 2k
THD+N (%)
10k
Frequency (Hz)
G = 10
RL = 10k
RL = 600
0.001
RL = 2k
G=1
RL = 10k
0.0001
G = 10
3k
2k
G=1
1k
0
20
100
1k
10k
10
20k
®
OPA340/2340/4340
100
1k
10k
100k
Frequency (Hz)
Frequency (Hz)
4
1M
10M
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = +5V, and RL = 10kΩ connected to VS/2, unless otherwise noted.
OPEN-LOOP GAIN AND POWER SUPPLY REJECTION
vs TEMPERATURE
130
120
COMMON-MODE REJECTION vs TEMPERATURE
100
RL = 100kΩ
AOL
90
AOL, PSRR (dB)
RL = 10kΩ
CMRR (dB)
80
110
RL = 2kΩ
100
PSRR
90
70
60
VS = 2.7V to 5V, VCM = –0.3V to (V+) –1.8V
VS = 5V, VCM = –0.3V to 5.3V
VS = 2.7V, VCM = –0.3V to 3V
50
80
40
–75
–50
–25
0
25
50
75
100
125
–75
–50
–25
Temperature (°C)
50
75
100
125
800
Per Amplifier
Per Amplifier
Quiescent Current (µA)
900
Quiescent Current (µA)
25
QUIESCENT CURRENT vs SUPPLY VOLTAGE
QUIESCENT CURRENT vs TEMPERATURE
1000
800
700
600
500
750
700
650
600
–75
–50
–25
0
25
50
75
100
125
2.0
2.5
3.0
Temperature (°C)
4.5
5.0
5.5
6.0
60
Short-Circuit Current (mA)
–ISC
80
70
60
50
4.0
SHORT-CIRCUIT CURRENT vs SUPPLY VOLTAGE
SHORT-CIRCUIT CURRENT vs TEMPERATURE
90
3.5
Supply Voltage (V)
100
Short-Circuit Current (mA)
0
Temperature (°C)
+ISC
40
30
20
–ISC
50
+ISC
40
10
0
30
–75
–50
–25
0
25
50
75
100
125
2.0
Temperature (°C)
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
Supply Voltage (V)
®
5
OPA340/2340/4340
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = +5V, and RL = 10kΩ connected to VS/2, unless otherwise noted.
INPUT BIAS CURRENT
vs INPUT COMMON-MODE VOLTAGE
INPUT BIAS CURRENT vs TEMPERATURE
1.0
1k
0.6
100
Input Bias Current (pA)
Input Bias Current (pA)
0.8
10
1
0.4
0.2
0
–0.2
–0.4
–0.6
–0.8
–1.0
0.1
–75
–50
–25
0
25
50
Temperature (°C)
75
100
125
–1
0
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
+25°C
–55°C
Output Voltage (Vp-p)
Output Voltage (V)
3
2
+125°C
–55°C
+25°C
±10 ±20
±30 ±40
±50 ±60
5
6
Maximum output
voltage without
slew rate-induced
distortion.
4
VS = 2.7V
3
2
1M
10M
Output Current (mA)
Frequency (Hz)
OFFSET VOLTAGE
PRODUCTION DISTRIBUTION
OFFSET VOLTAGE DRIFT MAGNITUDE
PRODUCTION DISTRIBUTION
25
Percent of Amplifiers (%)
Typical production
distribution of
packaged units.
12
10
8
6
4
Typical production
distribution of
packaged units.
20
15
10
5
2
0
0
500
400
300
200
100
0
–100
–200
–300
–400
0
–500
Percent of Amplifiers (%)
14
VS = 5.5V
0
100k
±70 ±80 ±90 ±100
18
16
4
1
0
0
3
5
4
1
2
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
6
5
+125°C
1
Common-Mode Voltage (V)
2
3
4
5
6
7
8
9
10 11 12 13 15
Offset Voltage Drift (µV/°C)
Offset Voltage (µV)
®
OPA340/2340/4340
1
6
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = +5V, and RL = 10kΩ connected to VS/2, unless otherwise noted.
LARGE-SIGNAL STEP RESPONSE
CL = 100pF
1V/div
50mV/div
SMALL-SIGNAL STEP RESPONSE
CL = 100pF
1µs/div
1µs/div
SETTLING TIME vs CLOSED-LOOP GAIN
SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE
100
60
G = –1
0.01%
Settling Time (µs)
Overshoot (%)
50
G = +1
40
30
G = –5
20
10
10
0.1%
1
See text for
reducing overshoot.
G = +5
0.1
0
100
1000
10k
1
10
100
1000
Closed-Loop Gain (V/V)
Load Capacitance (pF)
®
7
OPA340/2340/4340
APPLICATIONS INFORMATION
Power supply pins should be bypassed with 0.01µF ceramic
capacitors.
OPA340 series op amps are fabricated on a state-of-the-art
0.6 micron CMOS process. They are unity-gain stable and
suitable for a wide range of general purpose applications.
Rail-to-rail input/output make them ideal for driving sampling A/D converters. In addition, excellent ac performance
makes them well-suited for audio applications. The class AB
output stage is capable of driving 600Ω loads connected to
any point between V+ and ground.
OPERATING VOLTAGE
OPA340 series op amps are fully specified from +2.7V to
+5V. However, supply voltage may range from +2.5V to
+5.5V. Parameters are guaranteed over the specified supply
range—a unique feature of the OPA340 series. In addition,
many specifications apply from –40°C to +85°C. Most
behavior remains virtually unchanged throughout the full
operating voltage range. Parameters which vary significantly with operating voltages or temperature are shown in
the typical performance curves.
Rail-to-rail input and output swing significantly increases
dynamic range, especially in low supply applications.
Figure 1 shows the input and output waveforms for the
OPA340 in unity-gain configuration. Operation is from a
single +5V supply with a 10kΩ load connected to VS /2.
The input is a 5Vp-p sinusoid. Output voltage is approximately 4.98Vp-p.
RAIL-TO-RAIL INPUT
The input common-mode voltage range of the OPA340
series extends 500mV beyond the supply rails. This is
achieved with a complementary input stage—an N-channel
input differential pair in parallel with a P-channel differential pair (see Figure 2). The N-channel pair is active for input
voltages close to the positive rail, typically
(V+) –1.3V to 500mV above the positive supply, while the
P-channel pair is on for inputs from 500mV below the
negative supply to approximately (V+) –1.3V. There is a
small transition region, typically (V+) –1.5V to (V+) –1.1V,
in which both pairs are on. This 400mV transition region
can vary ±300mV with process variation. Thus, the transition region (both stages on) can range from (V+) –1.8V to
(V+) –1.4V on the low end, up to (V+) –1.2V to (V+) –0.8V
on the high end.
VS = +5, G = +1, RL = 10kΩ
5
2V/div
VIN
5
VOUT
0
FIGURE 1. Rail-to-Rail Input and Output.
V+
Reference
Current
VIN+
VIN–
VBIAS1
VBIAS2
V–
(Ground)
FIGURE 2. Simplified Schematic.
®
OPA340/2340/4340
8
Class AB
Control
Circuitry
VO
OPA340 series op amps are laser-trimmed to the reduce
offset voltage difference between the N-channel and
P-channel input stages, resulting in improved commonmode rejection and a smooth transition between the
N-channel pair and the P-channel pair. However, within the
400mV transition region PSRR, CMRR, offset voltage,
offset drift, and THD may be degraded compared to operation outside this region.
CAPACITIVE LOAD AND STABILITY
OPA340 series op amps can drive a wide range of capacitive
loads. However, all op amps under certain conditions may
become unstable. Op amp configuration, gain, and load
value are just a few of the factors to consider when determining stability. An op amp in unity gain configuration is the
most susceptible to the effects of capacitive load. The
capacitive load reacts with the op amp’s output resistance,
along with any additional load resistance, to create a pole in
the small-signal response which degrades the phase margin.
In unity gain, OPA340 series op amps perform well, with a
pure capacitive load up to approximately 1000pF. Increasing
gain enhances the amplifier’s ability to drive more capacitance. See the typical performance curve “Small-Signal
Overshoot vs Capacitive Load.”
A double-folded cascode adds the signal from the two input
pairs and presents a differential signal to the class AB output
stage. Normally, input bias current is approximately 200fA,
however, input voltages exceeding the power supplies by
more than 500mV can cause excessive current to flow in or
out of the input pins. Momentary voltages greater than
500mV beyond the power supply can be tolerated if the
current on the input pins is limited to 10mA. This is easily
accomplished with an input resistor as shown in Figure 3.
Many input signals are inherently current-limited to less
than 10mA, therefore, a limiting resistor is not required.
One method of improving capacitive load drive in the unity
gain configuration is to insert a 10Ω to 20Ω resistor in series
with the output, as shown in Figure 4. This significantly
reduces ringing with large capacitive loads. However, if
there is a resistive load in parallel with the capacitive load,
it creates a voltage divider introducing a dc error at the
output and slightly reduces output swing. This error may be
insignificant. For instance, with RL = 10kΩ and RS = 20Ω,
there is only about a 0.2% error at the output.
V+
IOVERLOAD
10mA max
DRIVING A/D CONVERTERS
VOUT
OPAx340
VIN
OPA340 series op amps are optimized for driving medium
speed (up to 100kHz) sampling A/D converters. However,
they also offer excellent performance for higher speed
converters. The OPA340 series provides an effective means
of buffering the A/D’s input capacitance and resulting
charge injection while providing signal gain.
5kΩ
FIGURE 3. Input Current Protection for Voltages Exceeding
the Supply Voltage.
Figures 5 and 6 show the OPA340 driving an ADS7816.
The ADS7816 is a 12-bit, micro-power sampling converter
in the tiny MSOP-8 package. When used with the miniature package options of the OPA340 series, the combination is ideal for space-limited and low power applications.
For further information consult the ADS7816 data sheet.
RAIL-TO-RAIL OUTPUT
A class AB output stage with common-source transistors is
used to achieve rail-to-rail output. For light resistive loads
(>50kΩ), the output voltage is typically a few millivolts
from the supply rails. With moderate resistive loads (2kΩ to
50kΩ), the output can swing to within a few tens of millivolts from the supply rails and maintain high open-loop
gain. See the typical performanc curve “Output Voltage
Swing vs Output Current.”
With the OPA340 in a noninverting configuration, an RC
network at the amplifier’s output can be used to filter high
frequency noise in the signal (Figure 5). In the inverting
configuration, filtering may be accomplished with a capacitor across the feedback resistor (Figure 6).
V+
RS
VOUT
OPAx340
VIN
10Ω to
20Ω
RL
CL
FIGURE 4. Series Resistor in Unity-Gain Configuration Improves Capacitive Load Drive.
®
9
OPA340/2340/4340
+5V
0.1µF
0.1µF
1 VREF
8 V+
500Ω
DCLOCK
+In
OPA340
ADS7816
12-Bit A/D
2
VIN
–In
CS/SHDN
3
3300pF
DOUT
7
6
5
Serial
Interface
GND 4
VIN = 0V to 5V for
0V to 5V output.
NOTE: A/D Input = 0 to VREF
RC network filters high frequency noise.
FIGURE 5. OPA340 in Noninverting Configuration Driving ADS7816.
+5V
330pF
0.1µF
5kΩ
0.1µF
5kΩ
VIN
8 V+
1 VREF
DCLOCK
+In
OPA340
ADS7816
12-Bit A/D
2
–In
DOUT
CS/SHDN
3
7
6
5
Serial
Interface
GND 4
VIN = 0V to –5V for 0V to 5V output.
NOTE: A/D Input = 0 to VREF
FIGURE 6. OPA340 in Inverting Configuration Driving ADS7816.
Filters 160Hz to 2.4kHz
+5V
10MΩ
VIN
200pF
10MΩ
1/2
OPA2340
243kΩ
1.74MΩ
47pF
1/2
OPA2340
RL
220pF
FIGURE 7. Speech Bandpass Filter.
®
OPA340/2340/4340
10
PACKAGE OPTION ADDENDUM
www.ti.com
6-Dec-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
OPA2340EA/250
ACTIVE
MSOP
DGK
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2340EA/250G4
ACTIVE
MSOP
DGK
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2340EA/2K5
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2340EA/2K5G4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2340PA
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA2340PAG4
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA2340UA
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2340UA/2K5
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2340UA/2K5G4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA2340UAG4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA340NA/250
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA340NA/250G4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA340NA/3K
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA340NA/3KG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA340PA
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA340PAG4
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA340UA
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA340UA/2K5
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA340UA/2K5G4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA340UAG4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA4340EA/250
ACTIVE
SSOP/
QSOP
DBQ
16
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA4340EA/250G4
ACTIVE
SSOP/
QSOP
DBQ
16
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA4340EA/2K5
ACTIVE
SSOP/
QSOP
DBQ
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA4340EA/2K5G4
ACTIVE
SSOP/
QSOP
DBQ
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA4340PA
OBSOLETE
PDIP
N
14
Addendum-Page 1
TBD
Lead/Ball Finish
Call TI
MSL Peak Temp (3)
Call TI
PACKAGE OPTION ADDENDUM
www.ti.com
6-Dec-2006
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
OPA4340UA
ACTIVE
SOIC
D
14
OPA4340UA/2K5
ACTIVE
SOIC
D
OPA4340UA/2K5G4
ACTIVE
SOIC
OPA4340UAG4
ACTIVE
SOIC
58
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
D
14
CU NIPDAU
Level-3-260C-168 HR
58
Green (RoHS &
no Sb/Br)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0.430 (10,92)
MAX
0.010 (0,25) M
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power Wireless www.ti.com/lpw
Mailing Address:
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2006, Texas Instruments Incorporated