PASSIVE POWER FACTOR CORRECTION INDUCTORS P1900 SERIES • Designed for use in off-line AC-DC pre-regulators circuits for switching power converters applications • Low core loss and high flux density • Insulation class system: B (130°C), F (155°C) or H(180°C) • Dielectric Withstanding Voltage (DWV): 2KVRMS • Operating Temperature: -20°C to +105°C • RoHS Compliant Product • Custom Design Available ELECTRICAL PARAMETERS @ 25°C L (μH MIN)1 Part Number Terminal3 (S-F) DCR (mΩ MAX)1, 2 I @ 80% L (ADC) I @ 65% L (ADC) I @ 50% L (ADC) I @ 30% L (ADC) Pins Dia. (Ø AWG) LxWxH (in. MAX) PCB Mounting Layout P19000 240 1-5, 2-4 28 16.50 37.00 60.00 60.00 14 x 2 2.7x1.0x2.8 V / Fig. 2 P19001 290 1-5, 2-4 53 14.80 33.00 53.50 53.50 14 x 2 2.7x1.0x2.8 V / Fig. 2 P19002 400 1-5, 2-4 120 10.60 24.00 38.50 38.50 15 x 2 2.6x1.0x2.7 V / Fig. 3 P19003 440 1-5, 2-4 55 12.20 27.00 44.00 44.00 15 x 2 2.6x1.0x2.7 V / Fig. 3 P19004 440 1-5, 2-4 55 12.20 27.00 44.00 44.00 15 x 2 2.6x2.6x1.0 H / Fig. 4 P19005 490 1-5, 2-4 118 11.20 25.00 40.50 40.50 15 x 2 2.6x1.0x2.7 V / Fig. 3 P19006 500 1-5, 2-4 90 11.40 26.00 41.50 41.50 15 x 2 2.6x1.0x2.7 V / Fig. 3 P19007 820 2-5 95 7.50 17.00 27.00 27.00 14 2.7x1.0x2.8 V / Fig. 1 P19008 1600 2-5 241 6.40 14.00 23.00 23.00 15 2.7x1.0x2.8 V / Fig. 1 P19009 2000 2-5 286 5.70 13.00 20.50 20.50 15 2.7x1.0x2.8 V / Fig. 1 1. Test conditions: 10KHz, 1VRMS. 2. Combined resistance of the “x2” winding. 3. Only those assigned terminals will have the self-lead pins. DIMENSIONS (mm) SCHEMATICS VERTICAL L W 1.20 [30.48] 0.60 [15.24] H 0.18 [4.57] 1.00 [25.40] P19XXXMPSDC 1 2 Figure 2 Figure 1 0.25 [6.35] 6 5 4 1 2 3 6 5 4 1.00 [25.40] S F 2.00 [50.80] Ø AWG HORIZONTAL Figure 3 Figure 4 1.575 [40.005] L&W P19XXXMPSDC 2 1 H 1.00 [25.40] 0.20 [5.08] 6 5 4 1 2 3 1.375 [34.925] 2.00 [50.80] 0.85 [21.59] ØL 0.984 [25.000] Typ. 2 1 0.20 [5.08] Typ. Product performance is limited to specified parameters. Data is subject to change without prior notice. Tel: 310-325-1043 Fax: 310-325-1044 0.85 [21.59] 1 2 3 2.00 [50.80] 3 0.18 [4.57] 0.85 [21.59] 0.50 [12.70] Dimensions Unless otherwise specified, all tolerances are: inch: .XX : ±0.015 .XXX : ±0.004 mm: X,X : ±0,38 X,XX : ±0,10 www.mpsind.com [email protected]