LoPro DPDT 400MHz Switch ANALOG PRODUCTS DIVISION Description Features Low On-Resistance: 7.0Ω typical. Vcc Range: 2.7V to 4.2V ±10% Switching Speed 20nS Break-Before-Make Switching Extended Industrial Temperature Range: –40°C to 85°C ™ LoPro Packaging (Pb-free): 10-Lead Micro Package Bandwidth 400MHz @ -3dB roll-off. Compatible with 1.8V systems. Power off protection. rd The bandwidth of 400MHz allows passing of the 2 Harmonic, resulting in minimal edge and phase distortion. Superior channel to channel crosstalk minimizes interference. The PA2070 contains circuitry for Power-Off protection when VCC = 0V. Data pins can tolerate up to 5.5V The PA2070 is compatible with 1.8 and 1.4V Systems. Applications ProTek Analog’s PA2070 is a bidirectional two-port Hi-speed switch. Configured as a double-pole double throw (DPDT), it is optimized for 400MHz switching. Hand Held Devices Cell Phones PDA’s Notebooks LCD Monitors Set Top Box USB2.0 Applications Functional Block Diagram HSD1+ D+ HSD2+ Pin Definitions D- Switch Enable 3 GND 4,5,6,7 HSD1n, HSD2n. Multiplexed DATA I/O D+, D- Common Port / USB DATA 1,2 HSD1- Ground 9 VCC Positive Power Supply 10 SEL Switch Select Logic Function Table OE SEL H X I/O’s = Hi-Z L L D+,D- = HSD1+, HSD1- L H D+,D- = HSD2+,HSD2-. Function HSD2Control SEL OE Pin Configuration (Top through View) OE 8 VCC 9 SEL 10 Temperature Range -40 to 85 °C HSD2- OE Description 7 6 1 2 D- 8 Name HSD2+ Pin No. D+ 95222 PA2070 ™ 5 HSD1+ 4 HSD1- 3 GND Package Part Number 10 Lead LoPro PA2070-T7 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480) 632-1715 www.protekanalog.com 95222 Rev.0. 06/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS PA2070 ™ LoPro DPDT 400MHz Switch ANALOG PRODUCTS DIVISION Absolute Maximum Ratings(1) Storage Temperature Range ……………….–65°C to +150°C Supply Voltage……………………...................... –0.5V to 4.6V DC Input Voltage…………………………………………...–0.5V to VCC +0.5V DC Output Current......................................................±120mA Power Dissipation (PD) @ +85°C…........................…500mW Notes:1. "Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. 2. The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. 3. Control input must be held HIGH or LOW; it must not float Recommended operating Conditions SYMBOL PARAMETER MIN MAX UNIT VCC Supply Voltage 2.7 4.2 V VCNTRL Control Input Voltage 0 VCC V VSW Switch I/O Voltage -0.5 4.5 V TA Operating Temperature °C DC Electrical Characteristics SYMBOL VIK PARAMETER CONDITIONS Clamp Diode Voltage IIN = 18mA VIH Input Voltage High VIL Input Voltage Low IIN Control Input Leakage IOZ Off State Leakage IOFF Power Off Leakage Current RON Switch On Resistance(1) VSW = 0 to VCC 0 ≤ Dn, HSD1n, HSD2n ≤ 3.6V VSW = 0V to 4.3V, VCC = 0V VCC (V) 3.0 TA = 40 °C to +85 °C MIN TYP MAX -1.2 UNITS V 3.0 to 3.6 1.3 V 4.2 1.7 V 3.0 to 3.6 0.5 V 4.2 0.7 V 4.2 -1 1 µA 4.2 -2 2 µA 0 -2 2 µA See Figure 4. VSW = 0V to 4.3V, ION = 8mA 3.0 7 Ω 3.0 0.6 Ω See Figure 3. Delta RON (2) VSW = 0.4V, ION = -8mA ICC Quiescent Supply Current VCNTRL = 0 or VCC, IOUT = 0 4.2 1.0 µA ICCT Increase in ICC per Control Voltage and VCC VCNTRL = 2.6V, VCC = 4.3V 4.2 10.0 µA VCNTRL = 1.8V, VCC = 4.3V 4.2 15.0 µA ∆RON Notes: 1. Measured by voltage drop between HSDn and Dn pins at the indicated current through the switch. 2. Guaranteed by characterization 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480) 632-1715 www.protekanalog.com 95222 Rev.0. 06/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS PA2070 ™ LoPro DPDT 400MHz Switch ANALOG PRODUCTS DIVISION AC Electrical Characteristics SYMBOL tON PARAMETER CONDITIONS Turn-On Time S, OE to Output RL = 50Ω, CL = 5pF VSW = 0.8V VCC (V) TA = 40 °C to +85 °C MIN TYP MAX UNITS 3.0 to 3.6 13 30 nS 3.0 to 3.6 12 25 nS 0.25 See Figure 5, Figure 6. Turn-Off Time S, OE to Output tOFF RL = 50Ω, CL = 5pF VSW = 0.8V See Figure 5, Figure 6 tPD tBBM Propagation Delay(3) RL = 50Ω, CL = 5pF 3.3 Break-Before-Make RL = 50Ω, CL = 5pF VSW = 0.8V 3.0 to 3.6 2.0 nS 6.0 nS See Figure 7. OIRR Off Isolation XTALK Non-Adjacent Channel Crosstalk RL = 50Ω, f = 240MHz See Figure 9. RL = 50Ω, f = 240MHz See Figure 10. RL = 50Ω, CL = 0pF BW -3dB Bandwidth See Figure 8. RL = 50Ω, CL = 5pF See Figure 8. 3.0 to 3.6 -30 dB 3.0 to 3.6 -45 dB 3.0 to 3.6 420 MHz 3.0 to 3.6 400 MHz VCC (V) TA = 40 °C to +85 °C MIN TYP MAX UNITS Notes: 3. Guaranteed by characterization USB High Speed Related AC Electrical Characteristics SYMBOL tSK(P) tJ PARAMETER CONDITIONS Skew of Opposite Transitions of the same Output RL = 50Ω, CL = 5pF. 3.0 to 3.6 20 pS RL = 50Ω, CL = 5pF tR=tF=500pS (10 to 90%) at 480Mbps (PRBS=215 1) 3.0 to 3.6 200 pS Total Jitter (4) Notes: 4. Guaranteed by characterization Capacitance TA = 40 °C to +85 °C MIN TYP MAX PARAMETER CONDITIONS CIN Control Pin Input Capacitance VCC = 0V 1.5 CON D+ / D- On Capacitance VCC = 3.3V, OE = 0V, f=240MHz 3.7 SYMBOL See Figure 12 COFF D1n, D2n Off Capacitance VCC = 3.3V, OE = 3.3V See Figure 11 2.0 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480) 632-1715 www.protekanalog.com 95222 Rev.0. 06/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS UNITS pF PA2070 ™ LoPro DPDT 400MHz Switch ANALOG PRODUCTS DIVISION Test Diagrams. VON HSDn VSW NC IDn (OFF) Dn A VSW ION SEL 0V or VCC SEL 0V or VCC GND **Each switch port tested separately GND Fig.3 On Resistance Dn HSDn VIN Fig.4 Off Leakage. VIH Logic Input VOUT Off 50% tr < 5nS On Off tf < 5nS VIL tOFF SEL RL 50Ω CL 5pF GND Logic Input Switch Output 90% 90% 0V tON RL , CL Are functions of the application Fig.5 AC Test Circuit VSW1 HSDn VSW2 HSDn Fig.6 Turn-On / Turn-Off Waveforms Dn VOUT SEL Logic Input RL 50Ω GND VCC Logic Input 0V CL 50% 5pF VOUT 0.9*VOUT 0.9*VOUT RL , CL Are functions of the application tBBM Fig.7 Break-Before-Make interval Timing 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480) 632-1715 www.protekanalog.com 95222 Rev.0. 06/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS PA2070 ™ LoPro DPDT 400MHz Switch ANALOG PRODUCTS DIVISION Test Diagrams. VCC VCC 10nF RS 50Ω 10nF RS 50Ω HSDn SEL Dn Signal Generator Network Analyzer SEL Logic Input 0V or VIH Dn Signal Generator Logic Input 0V or VIH HSDn RL 50Ω GND GND Analyzer CL 5pF RL , CL Are functions of the application Fig.8 Bandwidth RL 50Ω RL , CL Are functions of the application Fig.9 Channel Off Isolation VCC 10nF 50Ω HSDn Dn Signal Generator HSDn 50Ω SEL Analyzer GND CL 5pF RL 50Ω Fig.10 Non-Adjacent Channel-to-Channel Crosstalk VCC VCC 10nF 10nF Dn Capacitance Meter Dn SEL SEL Capacitance Meter Logic Input 0V or VIH f = 1MHz f = 1MHz Logic Input 0V or VIH HSDn HSDn GND Fig.11 Channel Off Capacitance. GND Fig.12 Channel On Capacitance. 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480) 632-1715 www.protekanalog.com 95222 Rev.0. 06/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS PA2070 ™ LoPro DPDT 400MHz Switch ANALOG PRODUCTS DIVISION Package Layout and Dimensions Bottom View Top View D E 6 A Pin 1 G 3 Pin 1 Area g B F 10 f Side View Recommended Land Pattern C 0.25 0.75 0.70 DIM A B C D E F G c c1 f g MIN 1.25 1.55 0.50 TYP 1.30 1.60 0.55 0.40 0.30 0.50 0.80 REF 0.00 - 0.05 0.10 REF 0.20 0.60 0.29 0.49 0.15 0.59 Max 1.35 1.65 0.60 PAD 1 c1 3 0.50 10 1.60 6 0.40 0.31 0.51 1.90 0.25 0.61 Note: Dimensions in millimeters Tape and Reel Specifications Reel Dia A0 B0 K0 D E F W P0 P2 P t-max 178 (7”) 1.47±0.05 1.73±0.05 0.65±0.05 1.50±0.10 1.75±0.10 3.50±0.05 12.00±0.30 4.00±0.10 2.00±0.05 4.00±0.10 0.25 P0 P2 D t 10 Pitches Cumulative Tolerance on Tape± 0.2 E Pin 1 indicated by Dot Top cover tape A0 B0 W 207 207 207 K0 F P 561 E. Elliot Road #175 Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480) 632-1715 www.protekanalog.com 95222 Rev.0. 06/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS