FREESCALE PCF5271CVM100

Freescale Semiconductor
Hardware Specification
MCF5271EC
Rev. 1.2, 12/2004
MCF5271 Integrated
Microprocessor
Hardware Specification
32-bit Embedded Controller Division
The MCF5271 family is a highly integrated
implementation of the ColdFire® family of reduced
instruction set computing (RISC) microprocessors. This
document describes pertinent features and functions of
the MCF5271 family. The MCF5271 family includes the
MCF5271 and MCF5270 microprocessors. The
differences between these parts are summarized below in
Table 1. This document is written from the perspective of
the MCF5271 and unless otherwise noted, the
information applies also to the MCF5270.
The MCF5271 family combines low cost with high
integration on the popular version 2 ColdFire core with
over 96 (Dhrystone 2.1) MIPS at 100MHz. Positioned
for applications requiring a cost-sensitive 32-bit
solution, the MCF5271 family features a 10/100 Ethernet
MAC and optional hardware encryption to ensure the
application can be connected and protected. In addition,
the MCF5271 family features an enhanced Multiply
Accumulate Unit (eMAC), large on-chip memory (64
Kbytes SRAM, 8 Kbytes configurable cache), and a
32-bit SDR SDRAM memory controller.
Technical Data
© Freescale Semiconductor, Inc., 2004. All rights reserved.
Table of Contents
1
2
3
4
5
6
7
8
9
MCF5271 Family Configurations ..................... 2
Block Diagram ................................................. 2
Features .......................................................... 4
Signal Descriptions........................................ 12
Modes of Operation....................................... 16
Design Recommendations ............................ 19
Mechanicals/Pinouts and Part Numbers ....... 27
Preliminary Electrical Characteristics............ 32
Documentation .............................................. 55
MCF5271 Family Configurations
1
MCF5271 Family Configurations
Table 1. MCF5271 Family Configurations
Module
ColdFire V2 Core with EMAC and
Hardware Divide
5270
5271
x
x
System Clock
100 MHz
Performance (Dhrystone/2.1 MIPS)
Instruction/Data Cache
8 Kbytes
Static RAM (SRAM)
64 Kbytes
Interrupt Controllers (INTC)
2
2
Edge Port Module (EPORT)
x
x
External Interface Module (EIM)
x
x
4-channel Direct-Memory Access (DMA)
x
x
SDRAM Controller
x
x
Fast Ethernet Controller (FEC)
x
x
Hardware Encryption
—
x
Watchdog Timer (WDT)
x
x
Four Periodic Interrupt Timers (PIT)
x
x
32-bit DMA Timers
4
4
QSPI
x
x
UART(s)
3
3
I2C
x
x
General Purpose I/O Module (GPIO)
x
x
JTAG - IEEE 1149.1 Test Access Port
x
x
Package
2
96
160 QFP,
160 QFP,
196 MAPBGA 196 MAPBGA
Block Diagram
The superset device in the MCF5271 family comes in a 196 mold array plastic ball grid array (MAPBGA)
package. Figure 1 shows a top-level block diagram of the MCF5271.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
2
Freescale Semiconductor
Block Diagram
SDRAMC
QSPI
EIM
I2C_SDA
I2C_SCL
CHIP
SELECTS
(To/From SRAM backdoor)
UnTXD
UnRXD
UnRTS
EBI
INTC0
Arbiter
UnCTS
INTC1
TnOUT
UART
0
UART
1
UART
2
I2 C
QSPI
SDRAMC
PADI – Pin Muxing
(To/From PADI)
FAST
ETHERNET
CONTROLLER
(FEC)
TnIN
FEC
D[31:0]
(To/From PADI)
4 CH DMA
DTIM
0
DTIM
1
DTIM
2
A[23:0]
DTIM
3
R/W
CS[3:0]
(To/From
PADI)
TA
TSIZ[1:0]
JTAG_EN
BDM
MUX
DREQ[2:0] DACK[2:0]
TEA
V2 ColdFire CPU
DIV
BS[3:0]
EMAC
JTAG
TAP
64 Kbytes
SRAM
(8Kx16)x4
Watchdog
Timer
MDHA
PORTS
(GPIO)
CIM
(To/From Arbiter)
SKHA
RNGA
8 Kbytes
CACHE
(1Kx32)x2
PLL
CLKGEN
PIT0
PIT1
PIT2
PIT3
(To/From INTC)
Edge
Port
Cryptography
Modules
Figure 1. MCF5271 Block Diagram
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
3
Features
3
Features
This document contains information on a new product. Specifications and information herein are subject
to change without notice.
3.1
•
•
•
•
•
Feature Overview
Version 2 ColdFire variable-length RISC processor core
— Static operation
— 32-bit address and data path on-chip
— Processor core runs at twice the bus frequency
— Sixteen general-purpose 32-bit data and address registers
— Implements the ColdFire Instruction Set Architecture, ISA_A, with extensions to support the
user stack pointer register, and 4 new instructions for improved bit processing
— Enhanced Multiply-Accumulate (EMAC) unit with four 48-bit accumulators to support 32-bit
signal processing algorithms
— Illegal instruction decode that allows for 68K emulation support
System debug support
— Real time trace for determining dynamic execution path
— Background debug mode (BDM) for in-circuit debugging
— Real time debug support, with two user-visible hardware breakpoint registers (PC and address
with optional data) that can be configured into a 1- or 2-level trigger
On-chip memories
— 8-Kbyte cache, configurable as instruction-only, data-only, or split I-/D-cache
— 64-Kbyte dual-ported SRAM on CPU internal bus, accessible by core and non-core bus
masters (e.g., DMA, FEC)
Fast Ethernet Controller (FEC)
— 10 BaseT capability, half duplex or full duplex
— 100 BaseT capability, half duplex or full duplex
— On-chip transmit and receive FIFOs
— Built-in dedicated DMA controller
— Memory-based flexible descriptor rings
— Media independent interface (MII) to external transceiver (PHY)
Three Universal Asynchronous Receiver Transmitters (UARTs)
— 16-bit divider for clock generation
— Interrupt control logic
— Maskable interrupts
— DMA support
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
4
Freescale Semiconductor
Features
—
—
—
—
•
•
•
•
•
•
Data formats can be 5, 6, 7 or 8 bits with even, odd or no parity
Up to 2 stop bits in 1/16 increments
Error-detection capabilities
Modem support includes request-to-send (URTS) and clear-to-send (UCTS) lines for two
UARTs
— Transmit and receive FIFO buffers
I2C Module
— Interchip bus interface for EEPROMs, LCD controllers, A/D converters, and keypads
— Fully compatible with industry-standard I2C bus
— Master or slave modes support multiple masters
— Automatic interrupt generation with programmable level
Queued Serial Peripheral Interface (QSPI)
— Full-duplex, three-wire synchronous transfers
— Up to four chip selects available
— Master mode operation only
— Programmable master bit rates
— Up to 16 pre-programmed transfers
Four 32-bit DMA Timers
— 20-ns resolution at 50 MHz
— Programmable sources for clock input, including an external clock option
— Programmable prescaler
— Input-capture capability with programmable trigger edge on input pin
— Output-compare with programmable mode for the output pin
— Free run and restart modes
— Maskable interrupts on input capture or reference-compare
— DMA trigger capability on input capture or reference-compare
Four Periodic Interrupt Timers (PITs)
— 16-bit counter
— Selectable as free running or count down
Software Watchdog Timer
— 16-bit counter
— Low power mode support
Frequency Modulated Phase Locked Loop (PLL)
— Crystal or external oscillator reference
— 8 to 25 MHz reference frequency for normal PLL mode
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
5
Features
— 24 to 50 MHz oscillator reference frequency for 1:1 mode
— Separate clock output pin
— Interrupt Controllers (x2)
– Support for up to 41 interrupt sources organized as follows: 34 fully-programmable
interrupt sources and 7 fixed-level external interrupt sources
•
•
•
— Unique vector number for each interrupt source
— Ability to mask any individual interrupt source or all interrupt sources (global mask-all)
— Support for hardware and software interrupt acknowledge (IACK) cycles
— Combinatorial path to provide wake-up from low power modes
DMA Controller
— Four fully programmable channels
— Dual-address and single-address transfer support with 8-, 16- and 32-bit data capability along
with support for 16-byte (4 x 32-bit) burst transfers
— Source/destination address pointers that can increment or remain constant
— 24-bit byte transfer counter per channel
— Auto-alignment transfers supported for efficient block movement
— Bursting and cycle steal support
— Software-programmable connections between the 12 DMA requesters in the UARTs (3),
32-bit timers (4), plus external logic (4), and the four DMA channels (4)
External Bus Interface
— Glueless connections to external memory devices (e.g., SRAM, Flash, ROM, etc.)
— SDRAM controller supports 8-, 16-, and 32-bit wide memory devices
— Support for n-1-1-1 burst fetches from page mode Flash
— Glueless interface to SRAM devices with or without byte strobe inputs
— Programmable wait state generator
— 32-bit bidirectional data bus
— 24-bit address bus
— Up to eight chip selects available
— Byte/write enables (byte strobes)
— Ability to boot from external memories that are 8, 16, or 32 bits wide
Chip Configuration Module (CCM)
— System configuration during reset
— Selects one of four clock modes
— Sets boot device and its data port width
— Configures output pad drive strength
— Unique part identification number and part revision number
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
6
Freescale Semiconductor
Features
— Reset
– Separate reset in and reset out signals
– Six sources of reset: Power-on reset (POR), External, Software, Watchdog, PLL loss of
clock, PLL loss of lock
– Status flag indication of source of last reset
•
•
3.2
General Purpose I/O interface
— Up to 61 bits of general purpose I/O
— Bit manipulation supported via set/clear functions
— Unused peripheral pins may be used as extra GPIO
JTAG support for system level board testing
V2 Core Overview
The processor core is comprised of two separate pipelines that are decoupled by an instruction buffer. The
two-stage Instruction Fetch Pipeline (IFP) is responsible for instruction-address generation and instruction
fetch. The instruction buffer is a first-in-first-out (FIFO) buffer that holds prefetched instructions awaiting
execution in the Operand Execution Pipeline (OEP). The OEP includes two pipeline stages. The first stage
decodes instructions and selects operands (DSOC); the second stage (AGEX) performs instruction
execution and calculates operand effective addresses, if needed.
The V2 core implements the ColdFire Instruction Set Architecture Revision A with added support for a
separate user stack pointer register and four new instructions to assist in bit processing. Additionally, the
MCF5271 core includes the enhanced multiply-accumulate unit (EMAC) for improved signal processing
capabilities. The EMAC implements a 4-stage execution pipeline, optimized for 32 x 32 bit operations,
with support for four 48-bit accumulators. Supported operands include 16- and 32-bit signed and unsigned
integers as well as signed fractional operands as well as a complete set of instructions to process these data
types. The EMAC provides superb support for execution of DSP operations within the context of a single
processor at a minimal hardware cost.
3.3
Debug Module
The ColdFire processor core debug interface is provided to support system debugging in conjunction with
low-cost debug and emulator development tools. Through a standard debug interface, users can access
real-time trace and debug information. This allows the processor and system to be debugged at full speed
without the need for costly in-circuit emulators. The debug interface is a superset of the BDM interface
provided on Freescale’s 683xx family of parts.
The on-chip breakpoint resources include a total of 6 programmable registers—a set of address registers
(with two 32-bit registers), a set of data registers (with a 32-bit data register plus a 32-bit data mask
register), and one 32-bit PC register plus a 32-bit PC mask register. These registers can be accessed through
the dedicated debug serial communication channel or from the processor’s supervisor mode programming
model. The breakpoint registers can be configured to generate triggers by combining the address, data, and
PC conditions in a variety of single or dual-level definitions. The trigger event can be programmed to
generate a processor halt or initiate a debug interrupt exception.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
7
Features
To support program trace, the Version 2 debug module provides processor status (PST[3:0]) and debug
data (DDATA[3:0]) ports. These buses and the PSTCLK output provide execution status, captured operand
data, and branch target addresses defining processor activity at the CPU’s clock rate.
3.4
JTAG
The MCF5271 supports circuit board test strategies based on the Test Technology Committee of IEEE and
the Joint Test Action Group (JTAG). The test logic includes a test access port (TAP) consisting of a 16-state
controller, an instruction register, and three test registers (a 1-bit bypass register, a 330-bit boundary-scan
register, and a 32-bit ID register). The boundary scan register links the device’s pins into one shift register.
Test logic, implemented using static logic design, is independent of the device system logic.
The MCF5271 implementation can do the following:
• Perform boundary-scan operations to test circuit board electrical continuity
• Sample MCF5271 system pins during operation and transparently shift out the result in the
boundary scan register
• Bypass the MCF5271 for a given circuit board test by effectively reducing the boundary-scan
register to a single bit
• Disable the output drive to pins during circuit-board testing
• Drive output pins to stable levels
3.5
3.5.1
On-chip Memories
Cache
The 8-Kbyte cache can be configured into one of three possible organizations: an 8-Kbyte instruction
cache, an 8-Kbyte data cache or a split 4-Kbyte instruction/4-Kbyte data cache. The configuration is
software-programmable by control bits within the privileged Cache Configuration Register (CACR). In all
configurations, the cache is a direct-mapped single-cycle memory, organized as 512 lines, each containing
16 bytes of data. The memories consist of a 512-entry tag array (containing addresses and control bits) and
a 8-Kbyte data array, organized as 2048 x 32 bits.
If the desired address is mapped into the cache memory, the output of the data array is driven onto the
ColdFire core's local data bus, completing the access in a single cycle. If the data is not mapped into the
tag memory, a cache miss occurs and the processor core initiates a 16-byte line-sized fetch. The cache
module includes a 16-byte line fill buffer used as temporary storage during miss processing. For all data
cache configurations, the memory operates in write-through mode and all operand writes generate an
external bus cycle.
3.5.2
SRAM
The SRAM module provides a general-purpose 64-Kbyte memory block that the ColdFire core can access
in a single cycle. The location of the memory block can be set to any 64-Kbyte boundary within the
4-Gbyte address space. The memory is ideal for storing critical code or data structures, for use as the
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
8
Freescale Semiconductor
Features
system stack, or for storing FEC data buffers. Because the SRAM module is physically connected to the
processor's high-speed local bus, it can quickly service core-initiated accesses or memory-referencing
commands from the debug module.
The SRAM module is also accessible by the DMA and FEC non-core bus masters. The dual-ported nature
of the SRAM makes it ideal for implementing applications with double-buffer schemes, where the
processor and a DMA device operate in alternate regions of the SRAM to maximize system performance.
As an example, system performance can be increased significantly if Ethernet packets are moved from the
FEC into the SRAM (rather than external memory) prior to any processing.
3.6
Fast Ethernet Controller (FEC)
The MCF5271’s integrated Fast Ethernet Controller (FEC) performs the full set of IEEE 802.3/Ethernet
CSMA/CD media access control and channel interface functions. The FEC supports connection and
functionality for the 10/100 Mbps 802.3 media independent interface (MII). It requires an external
transceiver (PHY) to complete the interface to the media.
3.7
UARTs
The MCF5271 contains three full-duplex UARTs that function independently. The three UARTs can be
clocked by the system bus clock, eliminating the need for an externally supplied clock. They can use DMA
requests on transmit-ready and receive-ready as well as interrupt requests for servicing. Flow control is
only available on two of the UARTs.
3.8
I2C Bus
The I2C bus is a two-wire, bidirectional serial bus that provides a simple, efficient method of data
exchange, minimizing the interconnection between devices. This bus is suitable for applications requiring
occasional communications over a short distance between many devices.
3.9
QSPI
The queued serial peripheral interface module provides a high-speed synchronous serial peripheral
interface with queued transfer capability. It allows up to 16 transfers to be queued at once, eliminating CPU
intervention between transfers.
3.10 Cryptography
The superset device, MCF5271, incorporates small, fast, dedicated hardware accelerators for random
number generation, message digest and hashing, and the DES, 3DES, and AES block cipher functions
allowing for the implementation of common Internet security protocol cryptography operations with
performance well in excess of software-only algorithms.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
9
Features
3.11 DMA Timers (DTIM0-DTIM3)
There are four independent, DMA-transfer-generating 32-bit timers (DTIM[3:0]) on the MCF5271. Each
timer module incorporates a 32-bit timer with a separate register set for configuration and control. The
timers can be configured to operate from the system clock or from an external clock source using one of
the DTINn signals. If the system clock is selected, it can be divided by 16 or 1. The input clock is further
divided by a user-programmable 8-bit prescaler which clocks the actual timer counter register (TCRn).
Each of these timers can be configured for input capture or reference compare mode. By configuring the
internal registers, each timer may be configured to assert an external signal, generate an interrupt on a
particular event or cause a DMA transfer.
3.12 Periodic Interrupt Timers (PIT0-PIT3)
The four periodic interrupt timers (PIT[3:0]) are 16-bit timers that provide precise interrupts at regular
intervals with minimal processor intervention. Each timer can either count down from the value written in
its PIT modulus register, or it can be a free-running down-counter.
3.13 Software Watchdog Timer
The watchdog timer is a 16-bit timer that facilitates recovery from runaway code. The watchdog counter
is a free-running down-counter that generates a reset on underflow. To prevent a reset, software must
periodically restart the countdown.
3.14 Clock Module and Phase Locked Loop (PLL)
The clock module contains a crystal oscillator (OSC), frequency modulated phase-locked loop (PLL),
reduced frequency divider (RFD), status/control registers, and control logic. To improve noise immunity,
the PLL and OSC have their own power supply inputs, VDDPLL and VSSPLL. All other circuits are
powered by the normal supply pins, VDD and VSS.
3.15 Interrupt Controllers (INTC0/INTC1)
There are two interrupt controllers on the MCF5271, each of which can support up to 63 interrupt sources
each for a total of 126. Each interrupt controller is organized as 7 levels with 9 interrupt sources per level.
Each interrupt source has a unique interrupt vector, and 56 of the 63 sources of a given controller provide
a programmable level [1-7] and priority within the level.
3.16 DMA Controller
The Direct Memory Access (DMA) Controller Module provides an efficient way to move blocks of data
with minimal processor interaction. The DMA module provides four channels (DMA0-DMA3) that allow
byte, word, longword or 16-byte burst line transfers. These transfers are triggered by software explicitly
setting a DCRn[START] bit. Other sources include the DMA timer, external sources via the DREQ signal,
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
10
Freescale Semiconductor
Features
and UARTs. The DMA controller supports single or dual address to off-chip devices or dual address to
on-chip devices.
3.17 External Interface Module (EIM)
The external bus interface handles the transfer of information between the core and memory, peripherals,
or other processing elements in the external address space. Features have been added to support external
Flash modules, for secondary wait states on reads and writes, and a signal to support Active-Low Address
Valid (a signal on most Flash memories).
Programmable chip-select outputs provide signals to enable external memory and peripheral circuits,
providing all handshaking and timing signals for automatic wait-state insertion and data bus sizing.
Base memory address and block size are programmable, with some restrictions. For example, the starting
address must be on a boundary that is a multiple of the block size. Each chip select can be configured to
provide read and write enable signals suitable for use with most popular static RAMs and peripherals. Data
bus width (8-bit, 16-bit, or 32-bit) is programmable on all chip selects, and further decoding is available
for protection from user mode access or read-only access.
3.18 SDRAM Controller
The SDRAM controller provides all required signals for glueless interfacing to a variety of
JEDEC-compliant SDRAM devices. SD_SRAS/SD_SCAS address multiplexing is software configurable
for different page sizes. To maintain refresh capability without conflicting with concurrent accesses on the
address and data buses, SD_RAS, SD_SCAS, SD_WE, SD_CS[1:0] and SD_CKE are dedicated SDRAM
signals.
3.19 Reset
The reset controller is provided to determine the cause of reset, assert the appropriate reset signals to the
system, and keep track of what caused the last reset. The power management registers for the internal
low-voltage detect (LVD) circuit are implemented in the reset module. There are six sources of reset:
• External
• Power-on reset (POR)
• Watchdog timer
• Phase locked-loop (PLL) loss of lock
• PLL loss of clock
• Software
External reset on the RSTOUT pin is software-assertable independent of chip reset state. There are also
software-readable status flags indicating the cause of the last reset.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
11
Signal Descriptions
3.20 GPIO
Unused bus interface and peripheral pins on the MCF5271 can be used as discrete general-purpose inputs
and outputs. These are managed by a dedicated GPIO module that logically groups all pins into ports
located within a contiguous block of memory-mapped control registers.
All of the pins associated with the external bus interface may be used for several different functions. Their
primary function is to provide an external memory interface to access off-chip resources. When not used
for this, all of the pins may be used as general-purpose digital I/O pins. In some cases, the pin function is
set by the operating mode, and the alternate pin functions are not supported.
The digital I/O pins on the MCF5271 are grouped into 8-bit ports. Some ports do not use all eight bits.
Each port has registers that configure, monitor, and control the port pins.
4
Signal Descriptions
This section describes signals that connect off chip, including a table of signal properties. For a more
detailed discussion of the MCF5271 signals, consult the MCF5235 Reference Manual (MCF5235RM).
4.1
Signal Properties
Table 2 lists all of the signals grouped by function. The “Dir” column is the direction for the primary
function of the pin. Refer to Section 7, “Mechanicals/Pinouts and Part Numbers,” for package diagrams.
NOTE
In this table and throughout this document a single signal within a group is
designated without square brackets (i.e., A24), while designations for
multiple signals within a group use brackets (i.e., A[23:21]) and is meant to
include all signals within the two bracketed numbers when these numbers
are separated by a colon.
NOTE
The primary functionality of a pin is not necessarily its default functionality.
Pins that are muxed with GPIO will default to their GPIO functionality.
Table 2. MCF5270 and MCF5271 Signal Information and Muxing
Signal Name
GPIO
Alternate 1 Alternate 2 Dir.1
MCF5270
MCF5271
160 QFP
MCF5270
MCF5271
196 MAPBGA
Reset
RESET
—
—
—
I
83
N13
RSTOUT
—
—
—
O
82
P13
Clock
EXTAL
—
—
—
I
86
M14
XTAL
—
—
—
O
85
N14
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
12
Freescale Semiconductor
Signal Descriptions
Table 2. MCF5270 and MCF5271 Signal Information and Muxing (continued)
Signal Name
GPIO
CLKOUT
—
MCF5270
MCF5271
160 QFP
MCF5270
MCF5271
196 MAPBGA
O
89
K14
Alternate 1 Alternate 2 Dir.1
—
—
Mode Selection
CLKMOD[1:0]
—
—
—
I
20,21
G5,H5
RCON
—
—
—
I
79
K10
126, 125, 124
B11, C11, D11
External Memory Interface and Ports
A[23:21]
PADDR[7:5]
CS[6:4]
—
O
A[20:0]
—
—
—
O
D[31:16]
—
—
—
O
22:30, 33:39
G1, G2, H1, H2,
H3, H4, J1, J2,
J3, J4, K1, K2,
K3, K4, L1, L2
D[15:8]
PDATAH[7:0]
—
—
O
42:49
M1, N1, M2, N2,
P2, L3, M3, N3
D[7:0]
PDATAL[7:0]
—
—
O
50:52, 56:60
P3, M4, N4, P4,
L5, M5, N5, P5
BS[3:0]
PBS[7:4]
CAS[3:0]
—
O
143:140
B6, C6, D7, C7
OE
PBUSCTL7
—
—
O
62
N6
TA
PBUSCTL6
—
—
I
96
H11
TEA
PBUSCTL5
DREQ1
—
I
—
J14
R/W
PBUSCTL4
—
—
O
95
J13
TSIZ1
PBUSCTL3
DACK1
—
O
—
P6
TSIZ0
PBUSCTL2
DACK0
—
O
—
P7
TS
PBUSCTL1
DACK2
—
O
97
H13
TIP
PBUSCTL0
DREQ0
—
O
—
H12
123:115,
A12, B12, C12,
112:106, 102:98 A13, B13, B14,
C13, C14, D12,
D13, D14, E11,
E12, E13, E14,
F12, F13, F14,
G11, G12, G13
Chip Selects
CS[7:4]
PCS[7:4]
—
—
O
—
B9, A10, C10,
A11
CS[3:2]
PCS[3:2]
SD_CS[1:0]
—
O
132,131
A9, C9
CS1
PCS1
—
—
O
130
B10
CS0
—
—
—
O
129
D10
SDRAM Controller
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
13
Signal Descriptions
Table 2. MCF5270 and MCF5271 Signal Information and Muxing (continued)
MCF5270
MCF5271
160 QFP
MCF5270
MCF5271
196 MAPBGA
O
92
K13
—
O
91
K12
—
—
O
90
K11
—
—
O
139
E8
—
—
O
—
L12, L13
Alternate 1 Alternate 2 Dir.1
Signal Name
GPIO
SD_WE
PSDRAM5
—
—
SD_SCAS
PSDRAM4
—
SD_SRAS
PSDRAM3
SD_CKE
PSDRAM2
SD_CS[1:0] PSDRAM[1:0]
External Interrupts Port
IRQ[7:3]
PIRQ[7:3]
—
—
I
IRQ7=63
IRQ4=64
N7, M7, L7, P8,
N8
IRQ2
PIRQ2
DREQ2
—
I
—
M8
IRQ1
PIRQ1
—
—
I
65
L8
FEC
EMDC
PFECI2C3
I2C_SCL
U2TXD
O
151
D4
EMDIO
PFECI2C2
I2C_SDA
U2RXD
I/O
150
D5
ECOL
—
—
—
I
9
E2
ECRS
—
—
—
I
8
E1
ERXCLK
—
—
—
I
7
D1
ERXDV
—
—
—
I
6
D2
ERXD[3:0]
—
—
—
I
5:2
D3, C1, C2, B1
ERXER
—
—
—
O
159
B2
ETXCLK
—
—
—
I
158
A2
ETXEN
—
—
—
I
157
C3
ETXER
—
—
—
O
156
B3
ETXD[3:0]
—
—
—
O
155:152
A3, A4, C4, B4
I2C
I2C_SDA
PFECI2C1
—
—
I/O
—
J12
I2C_SCL
PFECI2C0
—
—
I/O
—
J11
—
—
—
B7
DMA
DACK[2:0] and DREQ[2:0] do not have a dedicated bond
pads. Please refer to the following pins for muxing:
TS and DT2OUT for DACK2, TSIZ1and DT1OUT for DACK1,
TSIZ0 and DT0OUT for DACK0, IRQ2 and DT2IN for DREQ2,
TEA and DT1IN for DREQ1, and TIP and DT0IN for DREQ0.
QSPI
QSPI_CS1
PQSPI4
SD_CKE
—
O
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
14
Freescale Semiconductor
Signal Descriptions
Table 2. MCF5270 and MCF5271 Signal Information and Muxing (continued)
MCF5270
MCF5271
160 QFP
MCF5270
MCF5271
196 MAPBGA
O
146
A6
—
O
147
C5
I2C_SDA
—
I
148
B5
—
—
O
149
A5
Alternate 1 Alternate 2 Dir.1
Signal Name
GPIO
QSPI_CS0
PQSPI3
—
—
QSPI_CLK
PQSPI2
I2C_SCL
QSPI_DIN
PQSPI1
QSPI_DOUT
PQSPI0
UARTs
U2TXD
PUARTH1
—
—
O
—
A8
U2RXD
PUARTH0
—
—
I
—
A7
U1CTS
PUARTL7
U2CTS
—
I
136
B8
U1RTS
PUARTL6
U2RTS
—
O
135
C8
U1TXD
PUARTL5
—
—
O
133
D9
U1RXD
PUARTL4
—
—
I
134
D8
U0CTS
PUARTL3
—
—
I
12
F3
U0RTS
PUARTL2
—
—
O
15
G3
U0TXD
PUARTL1
—
—
O
14
F1
U0RXD
PUARTL0
—
—
I
13
F2
DMA Timers
DT3IN
PTIMER7
U2CTS
—
I
—
H14
DT3OUT
PTIMER6
U2RTS
—
O
—
G14
DT2IN
PTIMER5
DREQ2
DT2OUT
I
66
M9
DT2OUT
PTIMER4
DACK2
—
O
—
L9
DT1IN
PTIMER3
DREQ1
DT1OUT
I
61
L6
DT1OUT
PTIMER2
DACK1
—
O
—
M6
DT0IN
PTIMER1
DREQ0
—
I
10
E4
DT0OUT
PTIMER0
DACK0
—
O
11
F4
BDM/JTAG2
DSCLK
—
TRST
—
O
70
N9
PSTCLK
—
TCLK
—
O
68
P9
BKPT
—
TMS
—
O
71
P10
DSI
—
TDI
—
I
73
M10
DSO
—
TDO
—
O
72
N10
JTAG_EN
—
—
—
I
78
K9
DDATA[3:0]
—
—
—
O
—
M12, N12, P12,
L11
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
15
Modes of Operation
Table 2. MCF5270 and MCF5271 Signal Information and Muxing (continued)
Signal Name
GPIO
PST[3:0]
—
MCF5270
MCF5271
160 QFP
MCF5270
MCF5271
196 MAPBGA
O
77:74
M11, N11, P11,
L10
F5
Alternate 1 Alternate 2 Dir.1
—
—
Test
TEST
—
—
—
I
19
PLL_TEST
—
—
—
I
—
Power Supplies
VDDPLL
—
—
—
I
87
M13
VSSPLL
—
—
—
I
84
L14
OVDD
—
—
—
I
1, 18, 32, 41, 55, E5, E7, E10, F7,
69, 81, 94, 105, F9, G6, G8, H7,
114, 128, 138, H8, H9, J6, J8,
145
J10, K5, K6, K8
VSS
—
—
—
I
17, 31, 40, 54, A1, A14, E6, E9,
67, 80, 88, 93, F6, F8, F10, G7,
104, 113, 127, G9, H6, J5, J7,
137, 144, 160 J9, K7, P1, P14
VDD
—
—
—
I
16, 53, 103
D6, F11, G4, L4
NOTES:
Refers to pin’s primary function. All pins which are configurable for GPIO have a pullup enabled
in GPIO mode with the exception of PBUSCTL[7], PBUSCTL[4:0], PADDR, PBS, PSDRAM.
2 If JTAG_EN is asserted, these pins default to Alternate 1 (JTAG) functionality. The GPIO
module is not responsible for assigning these pins.
1
5
Modes of Operation
5.1
Chip Configuration Mode—Device
Operating Options
•
•
•
Chip operating mode:
— Master mode
Boot device/size:
— External device boot
– 32-bit
– 16-bit (Default)
– 8-bit
Output pad strength:
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
16
Freescale Semiconductor
Modes of Operation
— Partial drive strength (Default)
— Full drive strength
Clock mode:
— Normal PLL with external crystal
— Normal PLL with external clock
— 1:1 PLL Mode
— External oscillator mode (no PLL)
Chip Select Configuration:
— PADDR[7:5] configured as chip select(s) and/or address line(s)
– PADDR[7:5] configured as A23-A21 (default)
– PADDR configured as CS6, PADDR[6:5] as A22-A21
– PADDR[7:6] configured as CS[6:5], PADDR5 as A21
– PADDR[7:5] configured as CS[6:4]
•
•
5.1.1
Chip Configuration Pins
Table 3. Configuration Pin Descriptions
Pin
Chip Configuration
Function
Pin State/Meaning
Comments
RCON
Chip configuration
enable
1 Disabled
0 Enabled
D16
Select chip
operating mode
1 Master
0 Reserved
D20, D19
Select external boot
device data port size
00,11 External (32-bit)
10 External (8-bit)
01 External (16-bit)
D21
Select output pad
drive strength
1 Full
0 Partial
CLKMOD1,
CLKMOD0
Select clock mode
00 External clock mode (no VDDPLL must be supplied if a PLL
PLL)
mode is selected
01 1:1 PLL mode
10 Normal PLL with
external clock reference
11 Normal PLL with crystal
clock reference
Active low: if asserted, then all
configuration pins must be driven
appropriately for desired operation
Value read defaults to 32-bit
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
17
Modes of Operation
Table 3. Configuration Pin Descriptions (continued)
Pin
Chip Configuration
Function
Pin State/Meaning
D25, D24
Select chip select /
address line
00 PADDR[7:5] configured
as A23-A21 (default)
10 PADDR7 configured as
CS6,
PADDR[6:5] as A22-A21
01 PADDR[7:6] configured
as CS[6:5],
PADDR5 as A21
11 PADDR[7:5] configured
as CS[6:4]
JTAG_EN
Selects BDM or
JTAG mode
0 BDM mode
1 JTAG mode
5.2
Comments
Low Power Modes
The following features are available to support applications which require low power.
• Four modes of operation:
— RUN
— WAIT
— DOZE
— STOP
• Ability to shut down most peripherals independently.
• Ability to shut down the external CLKOUT pin.
There are four modes of operation: RUN, WAIT, DOZE, and STOP. The system enters a low power mode
when the user programs the low power bits (LPMD) in the LPCR (Low Power Control Register) in the
CIM before the CPU core executes a STOP instruction. This idles the CPU with no cycles active. The
LPMD bits indicate to the system and clock controller to power down and stop the clocks appropriately.
During STOP mode, the system clock is stopped low.
A wakeup event is required to exit a low power mode and return back to RUN mode. Wakeup events
consist of any of the following conditions. See the following sections for more details.
1. Any type of reset.
2. Assertion of the BKPT pin to request entry into Debug mode.
3. Debug request bit in the BDM control register to request entry into debug mode.
4. Any valid interrupt request.
5.2.1
RUN Mode
RUN mode is the normal system operating mode. Current consumption in this mode is related directly to
the frequency chosen for the system clock.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
18
Freescale Semiconductor
Design Recommendations
5.2.2
WAIT Mode
WAIT mode is intended to be used to stop only the CPU core and memory clocks until a wakeup event is
detected. In this mode, peripherals may be programmed to continue operating and can generate interrupts,
which cause the CPU core to exit from WAIT mode.
5.2.3
DOZE Mode
DOZE mode affects the CPU core in the same manner as WAIT mode, but with a different code on the
CIM LPMD bits, which are monitored by the peripherals. Each peripheral defines individual operational
characteristics in DOZE mode. Peripherals which continue to run and have the capability of producing
interrupts may cause the CPU to exit the DOZE mode and return to the RUN mode. Peripherals which are
stopped will restart operation on exit from DOZE mode as defined for each peripheral.
5.2.4
STOP Mode
STOP mode affects the CPU core in the same manner as the WAIT and DOZE modes, but with a different
code on the CCM LPMD bits. In this mode, all clocks to the system are stopped and the peripherals cease
operation.
STOP mode must be entered in a controlled manner to ensure that any current operation is properly
terminated. When exiting STOP mode, most peripherals retain their pre-stop status and resume operation.
5.2.5
Peripheral Shut Down
Most peripherals may be disabled by software in order to cease internal clock generation and remain in a
static state. Each peripheral has its own specific disabling sequence (refer to each peripheral description
for further details). A peripheral may be disabled at anytime and will remain disabled during any low
power mode of operation.
6
Design Recommendations
6.1
Layout
•
•
•
Use a 4-layer printed circuit board with the VDD and GND pins connected directly to the power
and ground planes for the MCF5271.
See application note AN1259 System Design and Layout Techniques for Noise Reduction in
processor-Based Systems.
Match the PC layout trace width and routing to match trace length to operating frequency and
board impedance. Add termination (series or therein) to the traces to dampen reflections.
Increase the PCB impedance (if possible) keeping the trace lengths balanced and short. Then do
cross-talk analysis to separate traces with significant parallelism or are otherwise "noisy". Use 6
mils trace and separation. Clocks get extra separation and more precise balancing.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
19
Design Recommendations
6.2
•
Power Supply
33 µF, .1 µF and .01 µF across each power supply
6.3
•
•
Decoupling
Place the decoupling caps as close to the pins as possible, but they can be outside the footprint of
the package.
.1 µF and .01 µF at each supply input
6.4
•
Buffering
Use bus buffers on all data/address lines for all off-board accesses and for all on-board accesses
when excessive loading is expected. See Section 8, “Preliminary Electrical Characteristics.”
6.5
•
Pull-up Recommendations
Use external pull-up resistors on unused inputs. See pin table.
6.6
•
•
•
•
•
•
•
•
Clocking Recommendations
Use a multi-layer board with a separate ground plane.
Place the crystal and all other associated components as close to the EXTAL and XTAL
(oscillator pins) as possible.
Do not run a high frequency trace around crystal circuit.
Ensure that the ground for the bypass capacitors is connected to a solid ground trace.
Tie the ground trace to the ground pin nearest EXTAL and XTAL. This prevents large loop
currents in the vicinity of the crystal.
Tie the ground pin to the most solid ground in the system.
Do not connect the trace that connects the oscillator and the ground plane to any other circuit
element. This tends to make the oscillator unstable.
Tie XTAL to ground when an external oscillator is clocking the device.
6.7
6.7.1
6.7.1.1
Interface Recommendations
SDRAM Controller
SDRAM Controller Signals in Synchronous Mode
Table 4 shows the behavior of SDRAM signals in synchronous mode.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
20
Freescale Semiconductor
Design Recommendations
Table 4. Synchronous DRAM Signal Connections
Signal
Description
SD_SRAS
Synchronous row address strobe. Indicates a valid SDRAM row address is present and can be
latched by the SDRAM. SD_SRAS should be connected to the corresponding SDRAM
SD_SRAS. Do not confuse SD_SRAS with the DRAM controller’s SD_CS[1:0], which should not
be interfaced to the SDRAM SD_SRAS signals.
SD_SCAS
Synchronous column address strobe. Indicates a valid column address is present and can be
latched by the SDRAM. SD_SCAS should be connected to the corresponding signal labeled
SD_SCAS on the SDRAM.
DRAMW
DRAM read/write. Asserted for write operations and negated for read operations.
SD_CS[1:0]
Row address strobe. Select each memory block of SDRAMs connected to the MCF5271. One
SD_CS signal selects one SDRAM block and connects to the corresponding CS signals.
SD_CKE
Synchronous DRAM clock enable. Connected directly to the CKE (clock enable) signal of
SDRAMs. Enables and disables the clock internal to SDRAM. When CKE is low, memory can
enter a power-down mode where operations are suspended or they can enter self-refresh mode.
SD_CKE functionality is controlled by DCR[COC]. For designs using external multiplexing,
setting COC allows SD_CKE to provide command-bit functionality.
BS[3:0]
Column address strobe. For synchronous operation, BS[3:0] function as byte enables to the
SDRAMs. They connect to the DQM signals (or mask qualifiers) of the SDRAMs.
CLKOUT
Bus clock output. Connects to the CLK input of SDRAMs.
6.7.1.2
Address Multiplexing
Table 5 shows the generic address multiplexing scheme for SDRAM configurations. All possible address
connection configurations can be derived from this table.
Table 5. Generic Address Multiplexing Scheme
Address Pin Row Address Column Address
Notes Related to Port Sizes
17
17
0
8-bit port only
16
16
1
8- and 16-bit ports only
15
15
2
14
14
3
13
13
4
12
12
5
11
11
6
10
10
7
9
9
8
17
17
16
32-bit port only
18
18
17
16-bit port only or 32-bit port with only 8
column address lines
19
19
18
16-bit port only when at least 9 column
address lines are used
20
20
19
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
21
Design Recommendations
Table 5. Generic Address Multiplexing Scheme (continued)
Address Pin Row Address Column Address
21
21
20
22
22
21
23
23
22
24
24
23
25
25
24
Notes Related to Port Sizes
The following tables provide a more comprehensive, step-by-step way to determine the correct address
line connections for interfacing the MCF5271 to SDRAM. To use the tables, find the one that corresponds
to the number of column address lines on the SDRAM and to the port size as seen by the MCF5271, which
is not necessarily the SDRAM port size. For example, if two 1M x 16-bit SDRAMs together form a
2M x 32-bit memory, the port size is 32 bits. Most SDRAMs likely have fewer address lines than are
shown in the tables, so follow only the connections shown until all SDRAM address lines are connected.
Table 6. MCF5271 to SDRAM Interface (8-Bit Port, 9-Column Address Lines)
MCF5271 A17 A16 A15 A14 A13 A12 A11 A10 A9 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31
Pins
Row
17
16
15
14
13
12
11
10
9
Column
0
1
2
3
4
5
6
7
8
SDRAM
Pins
18
19
20
21
22
23
24
25
26
27
28
29
30
31
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22
Table 7. MCF5271MCF5271 to SDRAM Interface (8-Bit Port,10-Column Address Lines)
MCF5271 A17 A16 A15 A14 A13 A12 A11 A10 A9 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31
Pins
Row
17
16
15
14
13
12
11
10
9
19
Column
0
1
2
3
4
5
6
7
8
18
SDRAM
Pins
20
21
22
23
24
25
26
27
28
29
30
31
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21
Table 8. MCF5271MCF5271 to SDRAM Interface (8-Bit Port,11-Column Address Lines)
MCF5271 A17 A16 A15 A14 A13 A12 A11 A10 A9 A19 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31
Pins
Row
17
16
15
14
13
12
11
10
9
19
21
Column
0
1
2
3
4
5
6
7
8
18
20
SDRAM
Pins
22
23
24
25
26
27
28
29
30
31
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
22
Freescale Semiconductor
Design Recommendations
Table 9. MCF5271MCF5271 to SDRAM Interface (8-Bit Port,12-Column Address Lines)
MCF5271 A17 A16 A15 A14 A13 A12 A11 A10 A9 A19 A21 A23 A24 A25 A26 A27 A28 A29 A30 A31
Pins
Row
17
16
15
14
13
12
11
10
9
19
21
23
Column
0
1
2
3
4
5
6
7
8
18
20
22
SDRAM
Pins
24
25
26
27
28
29
30
31
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19
Table 10. MCF5271MCF5271 to SDRAM Interface (8-Bit Port,13-Column Address Lines)
MCF5271 A17 A16 A15 A14 A13 A12 A11 A10 A9 A19 A21 A23 A25 A26 A27 A28 A29 A30 A31
Pins
Row
17
16
15
14
13
12
11
10
9
19
21
23
25
Column
0
1
2
3
4
5
6
7
8
18
20
22
24
SDRAM
Pins
26
27
28
29
30
31
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18
Table 11. MCF5271MCF5271 to SDRAM Interface (16-Bit Port, 8-Column Address Lines)
MCF5271 A16 A15 A14 A13 A12 A11 A10 A9 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31
Pins
Row
16
15
14
13
12
11
10
9
Column
1
2
3
4
5
6
7
8
SDRAM
Pins
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22
Table 12. MCF5271MCF5271 to SDRAM Interface (16-Bit Port, 9-Column Address Lines)
MCF5271 A16 A15 A14 A13 A12 A11 A10 A9 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31
Pins
Row
16
15
14
13
12
11
10
9
18
Column
1
2
3
4
5
6
7
8
17
SDRAM
Pins
19
20
21
22
23
24
25
26
27
28
29
30
31
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21
Table 13. MCF5271MCF5271 to SDRAM Interface (16-Bit Port, 10-Column Address Lines)
MCF5271 A16 A15 A14 A13 A12 A11 A10 A9 A18 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31
Pins
Row
16
15
14
13
12
11
10
9
18
20
21
22
23
24
25
26
27
28
29
30
31
Column
1
2
3
4
5
6
7
8
17
19
SDRAM
Pins
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
23
Design Recommendations
Table 14. MCF5271MCF5271 to SDRAM Interface (16-Bit Port, 11-Column Address Lines)
MCF5271 A16 A15 A14 A13 A12 A11 A10 A9 A18 A20 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31
Pins
Row
16
15
14
13
12
11
10
9
18
20
22
23
24
25
26
27
28
29
30
31
Column
1
2
3
4
5
6
7
8
17
19
21
SDRAM
Pins
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19
Table 15. MCF5271MCF5271 to SDRAM Interface (16-Bit Port, 12-Column Address Lines)
MCF5271 A16 A15 A14 A13 A12 A11 A10
Pins
A9
A18 A20 A22 A24 A25 A26 A27 A28 A29 A30 A31
Row
16
15
14
13
12
11
10
9
18
20
22
24
Column
1
2
3
4
5
6
7
8
17
19
21
23
SDRAM
Pins
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
25
26
27
28
29
30
31
A10 A11 A12 A13 A14 A15 A16 A17 A18
Table 16. MCF5271MCF5271 to SDRAM Interface (16-Bit Port, 13-Column-Address Lines)
MCF5271 A16 A15 A14 A13 A12 A11 A10
Pins
A9
A18 A20 A22 A24 A26 A27 A28 A29 A30 A31
Row
16
15
14
13
12
11
10
9
18
20
22
24
26
Column
1
2
3
4
5
6
7
8
17
19
21
23
25
SDRAM
Pins
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
27
28
29
30
31
A10 A11 A12 A13 A14 A15 A16 A17
Table 17. MCF5271MCF5271 to SDRAM Interface (32-Bit Port, 8-Column Address Lines)
MCF5271 A15 A14 A13 A12 A11 A10 A9 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31
Pins
Row
15
14
13
12
11
10
9
17
Column
2
3
4
5
6
7
8
16
SDRAM
Pins
18
19
20
21
22
23
24
25
26
27
28
29
30
31
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21
Table 18. MCF5271MCF5271 to SDRAM Interface (32-Bit Port, 9-Column Address Lines)
MCF5271 A15 A14 A13 A12 A11 A10 A9 A17 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31
Pins
Row
15
14
13
12
11
10
9
17
19
Column
2
3
4
5
6
7
8
16
18
SDRAM
Pins
A0
A1
A2
A3
A4
A5
A6
A7
A8
20
21
22
23
24
25
26
27
28
29
30
31
A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
24
Freescale Semiconductor
Design Recommendations
Table 19. MCF5271MCF5271 to SDRAM Interface (32-Bit Port, 10-Column Address Lines)
MCF5271 A15 A14 A13 A12 A11 A10 A9 A17 A19 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31
Pins
Row
15
14
13
12
11
10
9
17
19
21
22
23
24
25
26
27
28
29
30
31
Column
2
3
4
5
6
7
8
16
18
20
SDRAM
Pins
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19
Table 20. MCF5271MCF5271 to SDRAM Interface (32-Bit Port, 11-Column Address Lines)
MCF5271 A15 A14 A13 A12 A11 A10
Pins
A9
A17 A19 A21 A23 A24 A25 A26 A27 A28 A29 A30 A31
Row
15
14
13
12
11
10
9
17
19
21
23
Column
2
3
4
5
6
7
8
16
18
20
22
SDRAM
Pins
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
24
25
26
27
28
29
30
31
A10 A11 A12 A13 A14 A15 A16 A17 A18
Table 21. MCF5271MCF5271 to SDRAM Interface (32-Bit Port, 12-Column Address Lines)
MCF5271 A15 A14 A13 A12 A11 A10
Pins
A9
A17 A19 A21 A23 A25 A26 A27 A28 A29 A30 A31
Row
15
14
13
12
11
10
9
17
19
21
23
25
Column
2
3
4
5
6
7
8
16
18
20
22
24
SDRAM
Pins
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
6.7.1.3
26
27
28
29
30
31
A10 A11 A12 A13 A14 A15 A16 A17
SDRAM Interfacing Example
The tables in the previous section can be used to configure the interface in the following example. To
interface one 2M 32-bit 4 bank SDRAM component (8 columns) to the MCF5271, the connections would
be as shown in Table 22.
Table 22. SDRAM Hardware Connections
SDRAM
Pins
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10 = CMD
BA0
BA1
MCF5271
Pins
A15
A14
A13
A12
A11
A10
A9
A17
A18
A19
A20
A21
A22
6.7.2
Ethernet PHY Transceiver Connection
The FEC supports both an MII interface for 10/100 Mbps Ethernet and a seven-wire serial interface for 10
Mbps Ethernet. The interface mode is selected by R_CNTRL[MII_MODE]. In MII mode, the 802.3
standard defines and the FEC module supports 18 signals. These are shown in Table 23.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
25
Design Recommendations
Table 23. MII Mode
Signal Description
MCF5271 Pin
Transmit clock
ETXCLK
Transmit enable
ETXEN
Transmit data
ETXD[3:0]
Transmit error
ETXER
Collision
ECOL
Carrier sense
ECRS
Receive clock
ERXCLK
Receive enable
ERXDV
Receive data
ERXD[3:0]
Receive error
ERXER
Management channel clock
EMDC
Management channel serial data
EMDIO
The serial mode interface operates in what is generally referred to as AMD mode. The MCF5271
configuration for seven-wire serial mode connections to the external transceiver are shown in Table 24.
Table 24. Seven-Wire Mode Configuration
Signal Description
MCF5271 Pin
Transmit clock
ETXCLK
Transmit enable
ETXEN
Transmit data
ETXD[0]
Collision
ECOL
Receive clock
ERXCLK
Receive enable
ERXDV
Receive data
ERXD[0]
Unused, configure as PB14
ERXER
Unused input, tie to ground
ECRS
Unused, configure as PB[13:11]
ERXD[3:1]
Unused output, ignore
ETXER
Unused, configure as PB[10:8]
ETXD[3:1]
Unused, configure as PB15
EMDC
Input after reset, connect to ground
EMDIO
Refer to the M5271EVB evaluation board user’s manual for an example of how to connect an external
PHY. Schematics for this board are accessible at the MCF5271 site by navigating to:
http://www.freescale.com.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
26
Freescale Semiconductor
Mechanicals/Pinouts and Part Numbers
6.7.3
BDM
Use the BDM interface as shown in the M5271EVB evaluation board user’s manual. The schematics for
this board are accessible at the MCF5271 site by navigating from: http://www.freescale.com following the
32-bit Embedded Processors, 68K/ColdFire, MCF5xxx, MCF5271 and M5271EVB links.
7
Mechanicals/Pinouts and Part Numbers
This section contains drawings showing the pinout and the packaging and mechanical characteristics of
the MCF5271 devices. See Table 2 for a list the signal names and pin locations for each device.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
27
Mechanicals/Pinouts and Part Numbers
7.1
Pinout—196 MAPBGA
Figure 2 shows a pinout of the MCF5270/71CVMxxx package.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
VSS
ETXCLK
ETXD3
ETXD2
QSPI_
DOUT
QSPI_CS0
U2RXD
U2TXD
CS3
CS6
CS4
A20
A17
VSS
A
B
ERXD0
ERXER
ETXER
ETXD0
QSPI_DIN
BS3
QSPI_CS1
U1CTS
CS7
CS1
A23
A19
A16
A15
B
C
ERXD2
ERXD1
ETXEN
ETXD1
QSCK
BS2
BS0
RTS1
CS2
CS5
A22
A18
A14
A13
C
D
ERXCLK
ERXDV
ERXD3
EMDC
EMDIO
Core
VDD_4
BS1
U1RXD1
U1TXD
CS0
A21
A12
A11
A10
D
E
ECRS
ECOL
NC
TIN0
VDD
VSS
VDD
SD_CKE
VSS
VDD
A9
A8
A7
A6
E
F
U0TXD
U0RXD
U0CTS
DTOUT0
TEST
VSS
VDD
VSS
VDD
VSS
Core
VDD_3
A5
A4
A3
F
G
Data31
DATA30
U0RTS
Core
VDD_1
CLK
MOD1
VDD
VSS
VDD
VSS
NC
A2
A1
A0
DTOUT3
G
H
DATA29
DATA28
DATA27
DATA26
CLK
MOD0
VSS
VDD
VDD
VDD
NC
TA
TIP
TS
DTIN3
H
J
DATA25
DATA24
DATA23
DATA22
VSS
VDD
VSS
VDD
VSS
VDD
I2C_SCL
I2C_SDA
R/W
TEA
J
K
DATA21
DATA20
DATA19
DATA18
VDD
VDD
VSS
VDD
JTAG_EN
RCON
SD_ RAS
SD_ CAS
SD_ WE
CLKOUT
K
L
DATA17
DATA16
DATA10
Core
VDD_2
DATA3
DTIN1
IRQ5
IRQ1
DTOUT2
PST0
DDATA0
SD_ CS1
SD_ CS0
VSSPLL
L
M
DATA15
DATA13
DATA9
DATA6
DATA2
DTOUT1
PST3
DDATA3
VDDPLL
EXTAL
N
DATA14
DATA12
DATA8
DATA5
DATA1
OE
IRQ7
P
VSS
DATA11
DATA7
DATA4
DATA0
TSIZ1
1
2
3
4
5
6
DTIN2
TDI/DSI
IRQ3
TRST/
DSCLK
TDO/DSO
PST2
DDATA2
RESET
XTAL
N
TSIZ0
IRQ4
TCLK/
PSTCLK
TMS/
BKPT
PST1
DDATA1
RSTOUT
VSS
P
7
8
9
10
11
12
13
14
IRQ6
IRQ2
Figure 2. MCF5270/71CVMxxx Pinout (196 MAPBGA)
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
28
Freescale Semiconductor
M
Mechanicals/Pinouts and Part Numbers
7.2
Package Dimensions—196 MAPBGA
Figure 3 shows MCF5270/71CVMxxx package dimensions.
NOTES:
1. Dimensions are in millimeters.
2. Interpret dimensions and tolerances
per ASME Y14.5M, 1994.
3. Dimension B is measured at the
maximum solder ball diameter,
parallel to datum plane Z.
4. Datum Z (seating plane) is defined
by the spherical crowns of the solder
balls.
5. Parallelism measurement shall
exclude any effect of mark on top
surface of package.
D
X
Laser mark for pin 1
identification in
this area
Y
M
K
Millimeters
DIM Min Max
E
A
A1
A2
b
D
E
e
S
1.32 1.75
0.27 0.47
1.18 REF
0.35 0.65
15.00 BSC
15.00 BSC
1.00 BSC
0.50 BSC
M
0.20
13X
e
S
14 13 12 11 10
9
6
5
4
3
2
Metalized mark for
pin 1 identification
in this area
1
A
B
C
13X
5
D
S
E
e
F
A
0.30 Z
A2
G
H
J
K
L
M
A1
Z
4
0.15 Z
Detail K
Rotated 90 ° Clockwise
N
P
3
196X
b
View M-m
0.30 Z X Y
0.10 Z
Figure 3. 196 MAPBGA Package Dimensions (Case No. 1128A-01)
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
29
Mechanicals/Pinouts and Part Numbers
7.3
Pinout—160 QFP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
MCF5271
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A17
A16
A15
A14
A13
A12
O-VDD
VSS
A11
A10
A9
A8
A7
A6
A5
O-VDD
VSS
Core_Vdd_3
A4
A3
A2
A1
A0
TS
TA
R/W
O-VDD
VSS
SD_WE
SD_SCAS
SD_SRAS
CLKOUT
VSS
VDDPLL
EXTAL
XTAL
VSSPLL
RESET
RSTOUT
O-VDD
O-VDD
DATA15
DATA14
DATA13
DATA12
DATA11
DATA10
DATA9
DATA8
DATA7
DATA6
DATA5
Core Vdd_2
VSS
O-VDD
DATA4
DATA3
DATA2
DATA1
DATA0
DTIN1
OE
IRQ7
IRQ4
IRQ1
DTIN2
VSS
TCLK\PSTCLK
O-VDD
TRST/DSCLK
TMS\BKPT
TDO/DSO
TDI/DSI
PST0
PST1
PST2
PST3
JTAG_EN
RCON
VSS
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
O-VDD
ERXD0
ERXD1
ERXD2
ERXD3
ERXDV
ERXCLK
ECRS
ECOL
U0TIN
U0TOUT
U0CTS
U0RXD
U0TXD
U0RTS
Core VDD_1
VSS
O-VDD
TEST
CLKMOD1
CLKMOD0
DATA31
DATA30
DATA29
DATA28
DATA27
DATA26
DATA25
DATA24
DATA23
VSS
O-VDD
DATA22
DATA21
DATA20
DATA19
DATA18
DATA17
DATA16
VSS
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
VSS
ERXER
ETXCLK
ETXEN
ETXER
ETXD3
ETXD2
ETXD1
ETXD0
EMDC
EMDIO
QSPI_DOUT
QSPI_DIN
QSPI_CLK
QSPI_CS0
O-VDD
VSS
BS3
BS2
BS1
BS0
SD_CKE/QSPI_CS1
O-VDD
VSS
U1CTS
U1RTS
U1RXD
U1TXD
CS3
CS2
CS1
CS0
O-VDD
VSS
A23
A18
A21
A20
A19
A18
Figure 4 shows a pinout of the MCF5271CABxxx package.
Figure 4. MCF5270/71CABxxx Pinout (160 QFP)
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
30
Freescale Semiconductor
Mechanicals/Pinouts and Part Numbers
7.4
Package Dimensions—160 QFP
Figure 5 shows MCF5270/71CAB80 package dimensions.
L
A-B
B
H
V
B
0.20 (0.008) M
A-B
H
0.20 (0.008)
M
B
0.20 (0.008)
–B–
–A–
L
–A–, –B–, –D–
S
A-B S
D S
D S
Y
P
DETAIL A
G
DETAIL A
Z
A
0.20 (0.008) M C
0.20 (0.008)
S
A-B
BASE
METAL
D S
A-B
N
S
0.20 (0.008)
M C
A-B
S
J
D S
F
DETAIL C
D
0.13 (0.005) M
–H–
C A-B
S
D S
SECTION B–B
M×
TOP &
BOTTOM
U×
C
E
NOTES
T
–H–
R
Q×
W
–C–
K
H
X
0.110 (0.004)
DETAIL C
1. DIMENSIONING AND TOLERINCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER
3. DATUM PLAN -H- IS LOCATED AT BOTTOM OF
LEAD AND IS COINCIDENT WITH THE LEAD WHERE
THE LEAD EXITS THE PLASTIC BODY AT THE
BOTTOM OF THE PARTING LINE.
4. DATUMS -A-, -B-, AND -D- TO BE DETERMINED AT
DATUM PLANE -H-.
5. DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE -C-.
6. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS 0.25
(0.010) PER SIDE. DIMENSIONS A AND B DO
INCLUDE MOLD MISMATCH AND ARE DETERMINED
AT DATUM PLANE -H-.
7. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT.
MILLIMETERS
DIM MIN
MAX
A
27.90 28.10
27.90 28.10
B
3.85
3.35
C
0.22
0.38
D
3.20
3.50
E
0.22
0.33
F
0.65 BSC
G
H
0.25
0.35
0.11
0.23
J
K
0.70
0.90
25.35
BSC
L
5°
16°
M
0.11
0.19
N
0.325 BSC
P
Q
7°
0°
R
0.13
0.30
S
31.00 31.40
0.13
—
T
U
0°
—
V
31.00 31.40
0.4
—
W
1.60 REF
X
Y
1.33 REF
1.33 REF
Z
INCHES
MIN
MAX
1.098 1.106
1.098 1.106
0.132 1.106
0.009 0.015
0.126 0.138
0.009 0.013
0.026 REF
0.010 0.014
0.004 0.009
0.028 0.035
0.998 REF
5°
16°
0.004 0.007
0.013 REF
0°
7°
0.005 0.012
1.220 1.236
0.005
—
0°
—
1.220 1.236
0.016
—
0.063 REF
0.052 REF
0.052 REF
Case 864A-03
Figure 5. 160 QFP Package Dimensions
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
31
Preliminary Electrical Characteristics
7.5
Ordering Information
Table 25. Orderable Part Numbers
Freescale Part
Number
Description
Speed
Temperature
PCF5270AB100
MCF5270 RISC Microprocessor, 160 QFP
100MHz
0° to +70° C
PCF5270VM100
MCF5270 RISC Microprocessor, 196 MAPBGA
100MHz
0° to +70° C
PCF5271CAB100
MCF5271 RISC Microprocessor, 160 QFP
100MHz
-40° to +85° C
PCF5271CVM100
MCF5271 RISC Microprocessor, 196 MAPBGA
100MHz
-40° to +85° C
8
Preliminary Electrical Characteristics
This chapter contains electrical specification tables and reference timing diagrams for the MCF5271
microcontroller unit. This section contains detailed information on power considerations, DC/AC
electrical characteristics, and AC timing specifications of MCF5271.
The electrical specifications are preliminary and are from previous designs or design simulations. These
specifications may not be fully tested or guaranteed at this early stage of the product life cycle, however
for production silicon these specifications will be met. Finalized specifications will be published after
complete characterization and device qualifications have been completed.
NOTE
The parameters specified in this processor document supersede any values
found in the module specifications.
8.1
Maximum Ratings
Table 26. Absolute Maximum Ratings1, 2
Rating
Symbol
Value
Unit
Core Supply Voltage
VDD
– 0.5 to +2.0
V
Pad Supply Voltage
OVDD
– 0.3 to +4.0
V
VDDPLL
– 0.3 to +4.0
V
VIN
– 0.3 to + 4.0
V
ID
25
mA
TA
(TL - TH)
– 40 to 85
°C
Tstg
– 65 to 150
°C
Clock Synthesizer Supply Voltage
Digital Input Voltage
3
Instantaneous Maximum Current
Single pin limit (applies to all pins) 3,4,5
Operating Temperature Range (Packaged)
Storage Temperature Range
NOTES:
1
Functional operating conditions are given in DC Electrical Specifications. Absolute Maximum
Ratings are stress ratings only, and functional operation at the maxima is not guaranteed.
Continued operation at these levels may affect device reliability or cause permanent damage
to the device.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
32
Freescale Semiconductor
Preliminary Electrical Characteristics
2
This device contains circuitry protecting against damage due to high static voltage or
electrical fields; however, it is advised that normal precautions be taken to avoid application of
any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of
operation is enhanced if unused inputs are tied to an appropriate logic voltage level (e.g.,
either VSS or OVDD).
3 Input must be current limited to the value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive and negative clamp voltages,
then use the larger of the two values.
4
All functional non-supply pins are internally clamped to VSS and OVDD.
5
Power supply must maintain regulation within operating OVDD range during instantaneous
and operating maximum current conditions. If positive injection current (Vin > OVDD) is greater
than IDD, the injection current may flow out of OVDD and could result in external power supply
going out of regulation. Insure external OVDD load will shunt current greater than maximum
injection current. This will be the greatest risk when the processor is not consuming power
(ex; no clock).Power supply must maintain regulation within operating OVDD range during
instantaneous and operating maximum current conditions.
8.2
Thermal Characteristics
Table 27 lists thermal resistance values
Table 27. Thermal Characteristics
Characteristic
Symbol
196
160QFP
MAPBGA
Unit
Four layer board (2s2p)
θJMA
321,2
403,4
°C/W
Four layer board (2s2p)
θJMA
295,6
365,6
°C/W
Junction to board
θJB
205
6
25
°C/W
Junction to case
θJC
107
108
°C/W
Junction to top of package
Ψjt
25,9
25,10
°C/W
Maximum operating junction temperature
Tj
104
105
oC
Junction to ambient, natural convection
Junction to ambient (@200 ft/min)
NOTES:
1 θ
JMA and Ψjt parameters are simulated in conformance with EIA/JESD Standard 51-2 for natural convection.
Motorola recommends the use of θJmA and power dissipation specifications in the system design to prevent
device junction temperatures from exceeding the rated specification. System designers should be aware that
device junction temperatures can be significantly influenced by board layout and surrounding devices.
Conformance to the device junction temperature specification can be verified by physical measurement in the
customer’s system using the Ψjt parameter, the device power dissipation, and the method described in
EIA/JESD Standard 51-2.
2 Per JEDEC JESD51-6 with the board horizontal.
3
θJMA and Ψjt parameters are simulated in conformance with EIA/JESD Standard 51-2 for natural convection.
Motorola recommends the use of θJmA and power dissipation specifications in the system design to prevent
device junction temperatures from exceeding the rated specification. System designers should be aware that
device junction temperatures can be significantly influenced by board layout and surrounding devices.
Conformance to the device junction temperature specification can be verified by physical measurement in the
customer’s system using the Ψjt parameter, the device power dissipation, and the method described in
EIA/JESD Standard 51-2.
4
Per JEDEC JESD51-6 with the board horizontal.
5 Thermal resistance between the die and the printed circuit board in conformance with JEDEC JESD51-8.
Board temperature is measured on the top surface of the board near the package.
6 Thermal resistance between the die and the printed circuit board in conformance with JEDEC JESD51-8.
Board temperature is measured on the top surface of the board near the package.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
33
Preliminary Electrical Characteristics
7
Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL
SPEC-883 Method 1012.1).
8
Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL
SPEC-883 Method 1012.1).
9
Thermal characterization parameter indicating the temperature difference between package top and the
junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal
characterization parameter is written in conformance with Psi-JT.
10
Thermal characterization parameter indicating the temperature difference between package top and the
junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal
characterization parameter is written in conformance with Psi-JT.
The average chip-junction temperature (TJ) in °C can be obtained from:
T J = T A + ( P D × Θ JMA ) (1)
Where:
TA= Ambient Temperature, °C
ΘJMA= Package Thermal Resistance, Junction-to-Ambient, °C/W
PD= PINT + PI/O
PINT= IDD × VDD, Watts - Chip Internal Power
PI/O= Power Dissipation on Input and Output Pins — User Determined
For most applications PI/O < PINT and can be ignored. An approximate relationship between PD
and TJ (if PI/O is neglected) is:
P D = K ÷ ( T J + 273°C )
(2)
Solving equations 1 and 2 for K gives:
K = PD × (TA + 273 °C) + ΘJMA × PD 2 (3)
where K is a constant pertaining to the particular part. K can be determined from equation (3)
by measuring PD (at equilibrium) for a known TA. Using this value of K, the values of PD and
TJ can be obtained by solving equations (1) and (2) iteratively for any value of TA.
8.3
DC Electrical Specifications
Table 28. DC Electrical Specifications1
Characteristic
Symbol
Min
Typical
Max
Unit
Core Supply Voltage
VDD
1.35
—
1.65
V
Pad Supply Voltage
OVDD
3
—
3.6
V
Input High Voltage
VIH
0.7 OVDD
—
3.65
V
Input Low Voltage
VIL
VSS – 0.3
—
0.35 OVDD
V
VHYS
0.06 OVDD
—
—
mV
Iin
–1.0
—
1.0
µA
Input Hysteresis
Input Leakage Current
Vin = VDD or VSS, Input-only pins
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
34
Freescale Semiconductor
Preliminary Electrical Characteristics
Table 28. DC Electrical Specifications1 (continued)
Characteristic
Symbol
Min
Typical
Max
Unit
High Impedance (Off-State) Leakage Current
Vin = VDD or VSS, All input/output and output pins
IOZ
–1.0
—
1.0
µA
Output High Voltage (All input/output and all output pins)
IOH = –5.0 mA
VOH
OVDD - 0.5
—
__
V
Output Low Voltage (All input/output and all output pins)
IOL = 5.0mA
VOL
__
—
0.5
V
Weak Internal Pull Up Device Current, tested at VIL Max.2
IAPU
–10
—
– 130
µA
3
Input Capacitance
All input-only pins
All input/output (three-state) pins
Cin
—
—
—
Load Capacitance4
Low drive strength
High drive strength
CL
Core Operating Supply Current 5
Master Mode
IDD
pF
7
7
—
Pad Operating Supply Current
Master Mode
Low Power Modes
DC Injection Current 3, 6, 7, 8
VNEGCLAMP =VSS– 0.3 V, VPOSCLAMP = VDD + 0.3
Single Pin Limit
Total processor Limit, Includes sum of all stressed pins
pF
25
50
—
135
150
mA
—
—
100
TBD
—
—
mA
µA
OIDD
IIC
mA
–1.0
–10
1.0
10
NOTES:
1 Refer to Table 29 for additional PLL specifications.
2 Refer to the MCF5271 signals section for pins having weak internal pull-up devices.
3 This parameter is characterized before qualification rather than 100% tested.
4 pF load ratings are based on DC loading and are provided as an indication of driver strength. High speed interfaces require
transmission line analysis to determine proper drive strength and termination. See High Speed Signal Propagation:
Advanced Black Magic by Howard W. Johnson for design guidelines.
5 Current measured at maximum system clock frequency, all modules active, and default drive strength with matching load.
6
All functional non-supply pins are internally clamped to VSS and their respective VDD.
7 Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate
resistance values for positive and negative clamp voltages, then use the larger of the two values.
8
Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current
conditions. If positive injection current (Vin > VDD) is greater than IDD, the injection current may flow out of VDD and could
result in external power supply going out of regulation. Insure external VDD load will shunt current greater than maximum
injection current. This will be the greatest risk when the processor is not consuming power. Examples are: if no system
clock is present, or if clock rate is very low which would reduce overall power consumption. Also, at power-up, system clock
is not present during the power-up sequence until the PLL has attained lock.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
35
Preliminary Electrical Characteristics
8.4
Oscillator and PLLMRFM Electrical Characteristics
Table 29. HiP7 PLLMRFM Electrical Specifications1
Num
1
2
Characteristic
PLL Reference Frequency Range
Crystal reference
External reference
1:1 mode (NOTE: fsys/2 = 2 × fref_1:1)
Core frequency
CLKOUT Frequency 2
External reference
On-Chip PLL Frequency
Symbol
Min.
Value
Max.
Value
fref_crystal
fref_ext
fref_1:1
8
8
24
25
25
50
fsys/2
0
fref / 32
100
50
50
MHz
MHZ
MHz
Unit
MHz
fsys
3
Loss of Reference Frequency 3, 5
fLOR
100
1000
kHz
4
Self Clocked Mode Frequency 4, 5
fSCM
10.25
15.25
MHz
5
Crystal Start-up Time 5, 6
tcst
—
10
ms
6
XTAL Load Capacitance5
5
30
pF
7
PLL Lock Time 5, 7,13
tlpll
—
750
µs
8
Power-up To Lock Time 5, 6,8
With Crystal Reference (includes 5 time)
Without Crystal Reference9
tlplk
—
—
11
750
ms
µs
9
1:1 Mode Clock Skew (between CLKOUT
and EXTAL) 10
tskew
–1
1
ns
10
Duty Cycle of reference 5
tdc
40
60
%
11
Frequency un-LOCK Range
fUL
–3.8
4.1
% fsys/2
12
Frequency LOCK Range
fLCK
–1.7
2.0
% fsys/2
13
CLKOUT Period Jitter, 5, 6, 8,11, 12
Measured at fsys/2 Max
Peak-to-peak Jitter (Clock edge to clock
edge)
Long Term Jitter (Averaged over 2 ms
interval)
Cjitter
—
—
5.0
.01
% fsys/2
14
Frequency Modulation Range Limit13,14
(fsys/2 Max must not be exceeded)
Cmod
0.8
2.2
%fsys/2
15
ICO Frequency. fico = fref * 2 * (MFD+2) 15
fico
48
75
MHz
NOTES:
1 All values given are initial design targets and subject to change.
2
All internal registers retain data at 0 Hz.
3 “Loss of Reference Frequency” is the reference frequency detected internally, which transitions the PLL
into self clocked mode.
4 Self clocked mode frequency is the frequency that the PLL operates at when the reference frequency falls
below fLOR with default MFD/RFD settings.
5 This parameter is guaranteed by characterization before qualification rather than 100% tested.
6
Proper PC board layout procedures must be followed to achieve specifications.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
36
Freescale Semiconductor
Preliminary Electrical Characteristics
7
This specification applies to the period required for the PLL to relock after changing the MFD frequency
control bits in the synthesizer control register (SYNCR).
Assuming a reference is available at power up, lock time is measured from the time VDD and VDDSYN are
valid to RSTOUT negating. If the crystal oscillator is being used as the reference for the PLL, then the
crystal start up time must be added to the PLL lock time to determine the total start-up time.
tlpll = (64 * 4 * 5 + 5 τ) Tref, where Tref = 1/Fref_crystal = 1/Fref_ext = 1/Fref_1:1, and τ = 1.57x10-6 2(MFD +
2).
PLL is operating in 1:1 PLL mode.
Jitter is the average deviation from the programmed frequency measured over the specified interval at
maximum fsys/2. Measurements are made with the device powered by filtered supplies and clocked by a
stable external clock signal. Noise injected into the PLL circuitry via VDDSYN and VSSSYN and variation in
crystal oscillator frequency increase the Cjitter percentage for a given interval.
Values are with frequency modulation disabled. If frequency modulation is enabled, jitter is the sum of
Cjitter+Cmod.
Modulation percentage applies over an interval of 10µs, or equivalently the modulation rate is 100KHz.
Modulation rate selected must not result in fsys/2 value greater than the fsys/2 maximum specified value.
Modulation range determined by hardware design.
fsys/2 = fico / (2 * 2RFD)
8
9
10
11
12
13
14
15
8.5
External Interface Timing Characteristics
Table 30 lists processor bus input timings.
NOTE
All processor bus timings are synchronous; that is, input setup/hold and
output delay with respect to the rising edge of a reference clock. The
reference clock is the CLKOUT output.
All other timing relationships can be derived from these values.
Table 30. Processor Bus Input Timing Specifications
Characteristic1
Name
Symbol
Min
Max
Unit
50
50
MHz
1/50
ns
9
—
ns
9
—
ns
0
—
ns
tBKNCH
0
—
ns
freq
System bus frequency
fsys/2
B0
CLKOUT period
tcyc
Control Inputs
B1a
Control input valid to CLKOUT high
2
tCVCH
3
tBKVCH
B1b
BKPT valid to CLKOUT high
B2a
CLKOUT high to control inputs invalid2
B2b
CLKOUT high to asynchronous control input BKPT invalid3
tCHCII
Data Inputs
B4
Data input (D[31:0]) valid to CLKOUT high
tDIVCH
4
—
ns
B5
CLKOUT high to data input (D[31:0]) invalid
tCHDII
0
—
ns
NOTES:
1 Timing specifications are tested using full drive strength pad configurations in a 50ohm transmission line
environment..
2
TEA and TA pins are being referred to as control inputs.
3 Refer to figure A-19.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
37
Preliminary Electrical Characteristics
Timings listed in Table 30 are shown in Figure 6 & Figure A-3.
* The timings are also valid for inputs sampled on the negative clock edge.
1.5V
CLKOUT(75MHz)
TSETUP
THOLD
Input Setup And Hold
Invalid
1.5V Valid 1.5V
Invalid
trise
Input Rise Time
Vh = VIH
Vl = VIL
tfall
Input Fall Time
CLKOUT
Vh = VIH
Vl = VIL
B4
B5
Inputs
Figure 6. General Input Timing Requirements
8.6
Processor Bus Output Timing Specifications
Table 31 lists processor bus output timings.
Table 31. External Bus Output Timing Specifications
Name
Characteristic
Symbol
Min
Max
Unit
Control Outputs
B6a
CLKOUT high to chip selects valid 1
tCHCV
—
0.5tCYC +5
ns
B6b
CLKOUT high to byte enables (BS[3:0]) valid2
tCHBV
—
0.5tCYC +5
ns
B6c
CLKOUT high to output enable (OE) valid3
tCHOV
—
0.5tCYC +5
ns
B7
CLKOUT high to control output (BS[3:0], OE) invalid
tCHCOI
0.5tCYC+1.5
—
ns
B7a
CLKOUT high to chip selects invalid
tCHCI
0.5tCYC+1.5
—
ns
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
38
Freescale Semiconductor
Preliminary Electrical Characteristics
Table 31. External Bus Output Timing Specifications (continued)
Name
Characteristic
Symbol
Min
Max
Unit
Address and Attribute Outputs
B8
CLKOUT high to address (A[23:0]) and control (TS,
TSIZ[1:0], TIP, R/W) valid
tCHAV
—
9
ns
B9
CLKOUT high to address (A[23:0]) and control (TS,
TSIZ[1:0], TIP, R/W) invalid
tCHAI
1.5
—
ns
Data Outputs
B11
CLKOUT high to data output (D[31:0]) valid
tCHDOV
—
9
ns
B12
CLKOUT high to data output (D[31:0]) invalid
tCHDOI
1.5
—
ns
B13
CLKOUT high to data output (D[31:0]) high impedance
tCHDOZ
—
9
ns
NOTES:
CS transitions after the falling edge of CLKOUT.
2
BS transitions after the falling edge of CLKOUT.
3 OE transitions after the falling edge of CLKOUT.
1
Read/write bus timings listed in Table 31 are shown in Figure 7, Figure 8, and Figure 9.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
39
Preliminary Electrical Characteristics
S1
S0
S2
S3
S4
S5
S0
S1
S2
S3
S4
S5
CLKOUT
B7a
B7a
CSn
A[23:0]
TSIZ[1:0]
TS
B6a
B6a
B8
B8
B8
B9
B9
B9
B8
TIP
B9
B8
B6c
B0
B7
OE
B9
R/W (H)
B8
B6b
B6b
BS[3:0]
B7
B7
B11
B4
B12
D[31:0]
B5
B13
TA (H)
TEA (H)
Figure 7. Read/Write (Internally Terminated) SRAM Bus Timing
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
40
Freescale Semiconductor
Preliminary Electrical Characteristics
Figure 8 shows a bus cycle terminated by TA showing timings listed in Table 31.
S0
S1
S2
S3
S4
S5
S0
S1
CLKOUT
CSn
B6a
B7a
B8
B9
A[23:0]
TSIZ[1:0]
B8
B9
TS
B8
B9
TIP
OE
B6c
B7
R/W (H)
BS[3:0]
B6b
B7
B5
B4
D[31:0]
B2a
TA
TEA (H)
B1a
Figure 8. SRAM Read Bus Cycle Terminated by TA
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
41
Preliminary Electrical Characteristics
Figure 9 shows an SRAM bus cycle terminated by TEA showing timings listed in Table 31.
S0
S1
S2
S3
S4
S5
S0
S1
CLKOUT
CSn
B6a
B7a
B8
B9
A[23:0]
TSIZ[1:0]
B8
B9
TS
B8
TIP
OE
B9
B6c
B7
R/W (H)
BS[3:0]
B6b
B7
D[31:0]
TA (H)
B1a
TEA
B2a
Figure 9. SRAM Read Bus Cycle Terminated by TEA
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
42
Freescale Semiconductor
Preliminary Electrical Characteristics
Figure 10 shows an SDRAM read cycle.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SD_CKE
D3
D1
Row
A[23:0]
Column
D2
D4
RAS
D4
D2
CAS 1
D2
D4
SDWE
D6
D5
D[31:0]
D2
RAS[1:0]
D2
D4
CAS[3:0]
ACTV
1 DACR[CASL]
NOP
READ
NOP
NOP
PALL
=2
Figure 10. SDRAM Read Cycle
Table 32. SDRAM Timing
NUM
Characteristic
Symbol
Min
Max
Unit
D1
CLKOUT high to SDRAM address valid
tCHDAV
—
9
ns
D2
CLKOUT high to SDRAM control valid
tCHDCV
—
9
ns
D3
CLKOUT high to SDRAM address invalid
tCHDAI
1.5
—
ns
D4
CLKOUT high to SDRAM control invalid
tCHDCI
1.5
—
ns
D5
SDRAM data valid to CLKOUT high
tDDVCH
4
—
ns
D6
CLKOUT high to SDRAM data invalid
tCHDDI
1.5
—
ns
D71
CLKOUT high to SDRAM data valid
tCHDDVW
—
9
ns
D82
CLKOUT high to SDRAM data invalid
tCHDDIW
1.5
—
ns
NOTES:
1 D7 and D8 are for write cycles only.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
43
Preliminary Electrical Characteristics
Figure 11 shows an SDRAM write cycle.
0
1
2
3
4
5
6
7
8
9
10
11
12
SD_CKE
D3
D1
Row
A[23:0]
Column
D4
D2
SD_SRAS
D2
SD_SCAS1
D2
D4
SD_WE
D7
D[31:0]
D2
D8
RAS[1:0]
D4
D2
CAS[3:0]
ACTV
1 DACR[CASL]
NOP
WRITE
NOP
PALL
=2
Figure 11. SDRAM Write Cycle
8.7
General Purpose I/O Timing
Table 33. GPIO Timing1
NUM
G1
G2
G3
G4
Characteristic
Symbol
Min
Max
Unit
CLKOUT High to GPIO Output Valid
tCHPOV
—
10
ns
CLKOUT High to GPIO Output Invalid
tCHPOI
1.5
—
ns
GPIO Input Valid to CLKOUT High
tPVCH
9
—
ns
CLKOUT High to GPIO Input Invalid
tCHPI
1.5
—
ns
NOTES:
1
GPIO pins include: INT, UART, and Timer pins.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
44
Freescale Semiconductor
Preliminary Electrical Characteristics
CLKOUT
G1
G2
GPIO Outputs
G3
G4
GPIO Inputs
Figure 12. GPIO Timing
8.8
Reset and Configuration Override Timing
Table 34. Reset and Configuration Override Timing
(VDD = 2.7 to 3.6 V, VSS = 0 V, TA = TL to TH)1
NUM
Characteristic
Symbol
Min
Max
Unit
R1
RESET Input valid to CLKOUT High
tRVCH
9
—
ns
R2
CLKOUT High to RESET Input invalid
tCHRI
1.5
—
ns
tRIVT
5
—
tCYC
2
R3
RESET Input valid Time
R4
CLKOUT High to RSTOUT Valid
tCHROV
—
10
ns
R5
RSTOUT valid to Config. Overrides valid
tROVCV
0
—
ns
R6
Configuration Override Setup Time to RSTOUT invalid
tCOS
20
—
tCYC
R7
Configuration Override Hold Time after RSTOUT invalid
tCOH
0
—
ns
R8
RSTOUT invalid to Configuration Override High Impedance
tROICZ
—
1
tCYC
NOTES:
1
All AC timing is shown with respect to 50% VDD levels unless otherwise noted.
2 During low power STOP, the synchronizers for the RESET input are bypassed and RESET is asserted asynchronously to the
system. Thus, RESET must be held a minimum of 100 ns.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
45
Preliminary Electrical Characteristics
CLKOUT
R1
R2
R3
RESET
R4
R4
RSTOUT
R8
R5
R6
R7
Configuration Overrides*:
(RCON, Override pins])
Figure 13. RESET and Configuration Override Timing
* Refer to the Coldfire Integration Module (CIM) section for more information.
8.9
I2C Input/Output Timing Specifications
Table 35 lists specifications for the I2C input timing parameters shown in Figure 14.
Table 35. I2C Input Timing Specifications between I2C_SCL and I2C_SDA
Num
Characteristic
Min
Max
Units
I1
Start condition hold time
2
—
tcyc
I2
Clock low period
8
—
tcyc
I3
I2C_SCL/I2C_SDA rise time (VIL = 0.5 V to VIH = 2.4 V)
—
1
ms
I4
Data hold time
0
—
ns
I5
I2C_SCL/I2C_SDA fall time (VIH = 2.4 V to VIL = 0.5 V)
—
1
ms
I6
Clock high time
4
—
tcyc
I7
Data setup time
0
—
ns
I8
Start condition setup time (for repeated start condition only)
2
—
tcyc
I9
Stop condition setup time
2
—
tcyc
Table 36 lists specifications for the I2C output timing parameters shown in Figure 14.
Table 36. I2C Output Timing Specifications between I2C_SCL and I2C_SDA
Num
Characteristic
Min
Max
Units
I11
Start condition hold time
6
—
tcyc
I2 1
Clock low period
10
—
tcyc
I3 2
I2C_SCL/I2C_SDA rise time (VIL = 0.5 V to
VIH = 2.4 V)
—
—
µs
I4 1
Data hold time
7
—
tcyc
I2C_SCL/I2C_SDA fall time (VIH = 2.4 V to
VIL = 0.5 V)
—
3
ns
Clock high time
10
—
tcyc
I5
3
I6 1
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
46
Freescale Semiconductor
Preliminary Electrical Characteristics
Table 36. I2C Output Timing Specifications between I2C_SCL and I2C_SDA (continued)
Num
Characteristic
I7 1
I8
1
I9 1
Min
Max
Units
Data setup time
2
—
tcyc
Start condition setup time (for repeated start
condition only)
20
—
tcyc
Stop condition setup time
10
—
tcyc
NOTES:
1
Note: Output numbers depend on the value programmed into the IFDR; an IFDR
programmed with the maximum frequency (IFDR = 0x20) results in minimum output
timings as shown in Table 36. The I2C interface is designed to scale the actual data
transition time to move it to the middle of the I2C_SCL low period. The actual position is
affected by the prescale and division values programmed into the IFDR; however, the
numbers given in Table 36 are minimum values.
2
Because I2C_SCL and I2C_SDA are open-collector-type outputs, which the processor can
only actively drive low, the time I2C_SCL or I2C_SDA take to reach a high level depends on
external signal capacitance and pull-up resistor values.
3 Specified at a nominal 50-pF load.
Figure 14 shows timing for the values in Table 35 and Table 36.
I2
I6
I5
I2C_SCL
I1
I4
I8
I3
I9
I7
I2C_SDA
Figure 14. I2C Input/Output Timings
8.10 Fast Ethernet AC Timing Specifications
MII signals use TTL signal levels compatible with devices operating at either 5.0 V or 3.3 V.
8.10.1 MII Receive Signal Timing (ERXD[3:0], ERXDV, ERXER, and
ERXCLK)
The receiver functions correctly up to a ERXCLK maximum frequency of 25 MHz +1%. There is no
minimum frequency requirement. In addition, the processor clock frequency must exceed twice the
ERXCLK frequency.
Table 37 lists MII receive channel timings.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
47
Preliminary Electrical Characteristics
Table 37. MII Receive Signal Timing
Num
Characteristic
Min
Max
Unit
M1
ERXD[3:0], ERXDV, ERXER to ERXCLK setup
5
—
ns
M2
ERXCLK to ERXD[3:0], ERXDV, ERXER hold
5
—
ns
M3
ERXCLK pulse width high
35%
65%
ERXCLK period
M4
ERXCLK pulse width low
35%
65%
ERXCLK period
Figure 15 shows MII receive signal timings listed in Table 37.
M3
ERXCLK (input)
M4
ERXD[3:0] (inputs)
ERXDV
ERXER
M1
M2
Figure 15. MII Receive Signal Timing Diagram
8.10.2 MII Transmit Signal Timing (ETXD[3:0], ETXEN,
ETXER, ETXCLK)
Table 38 lists MII transmit channel timings.
The transmitter functions correctly up to a ETXCLK maximum frequency of 25 MHz +1%. There is no
minimum frequency requirement. In addition, the processor clock frequency must exceed twice the
ETXCLK frequency.
The transmit outputs (ETXD[3:0], ETXEN, ETXER) can be programmed to transition from either the
rising or falling edge of ETXCLK, and the timing is the same in either case. This options allows the use
of non-compliant MII PHYs.
Refer to the Ethernet chapter for details of this option and how to enable it.
Table 38. MII Transmit Signal Timing
Num
Characteristic
Min
Max
Unit
M5
ETXCLK to ETXD[3:0], ETXEN, ETXER invalid
5
—
ns
M6
ETXCLK to ETXD[3:0], ETXEN, ETXER valid
—
25
ns
M7
ETXCLK pulse width high
35%
65%
ETXCLK period
M8
ETXCLK pulse width low
35%
65%
ETXCLK period
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
48
Freescale Semiconductor
Preliminary Electrical Characteristics
Figure 16 shows MII transmit signal timings listed in Table 38.
M7
ETXCLK (input)
M5
M8
ETXD[3:0] (outputs)
ETXEN
ETXER
M6
Figure 16. MII Transmit Signal Timing Diagram
8.10.3 MII Async Inputs Signal Timing (ECRS and ECOL)
Table 39 lists MII asynchronous inputs signal timing.
Table 39. MII Async Inputs Signal Timing
Num
M9
Characteristic
Min
Max
Unit
1.5
—
ETXCLK period
ECRS, ECOL minimum pulse width
Figure 17 shows MII asynchronous input timings listed in Table 39.
ECRS, ECOL
M9
Figure 17. MII Async Inputs Timing Diagram
8.10.4 MII Serial Management Channel Timing (EMDIO and EMDC)
Table 40 lists MII serial management channel timings. The FEC functions correctly with a maximum
MDC frequency of 2.5 MHz.
Table 40. MII Serial Management Channel Timing
Num
Characteristic
Min
Max
Unit
M10
EMDC falling edge to EMDIO output invalid (minimum propagation
delay)
0
—
ns
M11
EMDC falling edge to EMDIO output valid (max prop delay)
—
25
ns
M12
EMDIO (input) to EMDC rising edge setup
10
—
ns
M13
EMDIO (input) to EMDC rising edge hold
0
—
ns
M14
EMDC pulse width high
40% 60% MDC period
M15
EMDC pulse width low
40% 60% MDC period
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
49
Preliminary Electrical Characteristics
Figure 18 shows MII serial management channel timings listed in Table 40.
M14
M15
EMDC (output)
M10
EMDIO (output)
M11
EMDIO (input)
M12
M13
Figure 18. MII Serial Management Channel Timing Diagram
8.11 32-Bit Timer Module AC Timing Specifications
Table 41 lists timer module AC timings.
Table 41. Timer Module AC Timing Specifications
0–66 MHz
Name
Characteristic
Unit
Min
Max
T1
DT0IN / DT1IN / DT2IN / DT3IN cycle time
3
—
tCYC
T2
DT0IN / DT1IN / DT2IN / DT3IN pulse width
1
—
tCYC
8.12 QSPI Electrical Specifications
Table 42 lists QSPI timings.
Table 42. QSPI Modules AC Timing Specifications
Name
Characteristic
Min
Max
Unit
QS1
QSPI_CS[1:0] to QSPI_CLK
1
510
tcyc
QS2
QSPI_CLK high to QSPI_DOUT valid.
—
10
ns
QS3
QSPI_CLK high to QSPI_DOUT invalid. (Output hold)
2
—
ns
QS4
QSPI_DIN to QSPI_CLK (Input setup)
9
—
ns
QS5
QSPI_DIN to QSPI_CLK (Input hold)
9
—
ns
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
50
Freescale Semiconductor
Preliminary Electrical Characteristics
The values in Table 42 correspond to Figure 19.
QS1
QSPI_CS[1:0]
QSPI_CLK
QS2
QSPI_DOUT
QS3
QS4
QS5
QSPI_DIN
Figure 19. QSPI Timing
8.13 JTAG and Boundary Scan Timing
Table 43. JTAG and Boundary Scan Timing
Characteristics1
Num
Symbol
Min
Max
Unit
J1
TCLK Frequency of Operation
fJCYC
DC
1/4
fsys/2
J2
TCLK Cycle Period
tJCYC
4
-
tCYC
J3
TCLK Clock Pulse Width
tJCW
26
-
ns
J4
TCLK Rise and Fall Times
tJCRF
0
3
ns
J5
Boundary Scan Input Data Setup Time to TCLK Rise
tBSDST
4
-
ns
J6
Boundary Scan Input Data Hold Time after TCLK Rise
tBSDHT
26
-
ns
J7
TCLK Low to Boundary Scan Output Data Valid
tBSDV
0
33
ns
J8
TCLK Low to Boundary Scan Output High Z
tBSDZ
0
33
ns
J9
TMS, TDI Input Data Setup Time to TCLK Rise
tTAPBST
4
-
ns
J10
TMS, TDI Input Data Hold Time after TCLK Rise
tTAPBHT
10
-
ns
J11
TCLK Low to TDO Data Valid
tTDODV
0
26
ns
J12
TCLK Low to TDO High Z
tTDODZ
0
8
ns
J13
TRST Assert Time
tTRSTAT
100
-
ns
J14
TRST Setup Time (Negation) to TCLK High
tTRSTST
10
-
ns
NOTES:
1 JTAG_EN is expected to be a static signal. Hence, specific timing is not associated with it.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
51
Preliminary Electrical Characteristics
J2
J3
J3
VIH
TCLK
(input)
J4
VIL
J4
Figure 20. Test Clock Input Timing
TCLK
VIL
VIH
J5
Data Inputs
J6
Input Data Valid
J7
Data Outputs
Output Data Valid
J8
Data Outputs
J7
Data Outputs
Output Data Valid
Figure 21. Boundary Scan (JTAG) Timing
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
52
Freescale Semiconductor
Preliminary Electrical Characteristics
TCLK
VIL
VIH
J9
TDI
TMS
J10
Input Data Valid
J11
TDO
Output Data Valid
J12
TDO
J11
TDO
Output Data Valid
Figure 22. Test Access Port Timing
TCLK
J14
TRST
J13
Figure 23. TRST Timing
8.14 Debug AC Timing Specifications
Table 44 lists specifications for the debug AC timing parameters shown in Figure 25.
Table 44. Debug AC Timing Specification
150 MHz
Num
Characteristic
Units
Min
DE0
PSTCLK cycle time
DE1
PST valid to PSTCLK high
DE2
PSTCLK high to PST invalid
DE3
DE4
Max
0.5
tcyc
4
ns
1.5
ns
DSCLK cycle time
5
tcyc
DSI valid to DSCLK high
1
tcyc
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
53
Preliminary Electrical Characteristics
Table 44. Debug AC Timing Specification (continued)
150 MHz
Num
Characteristic
Units
Min
Max
DE5 1
DSCLK high to DSO invalid
4
tcyc
DE6
BKPT input data setup time to
CLKOUT Rise
4
ns
DE7
CLKOUT high to BKPT high Z
0
10
ns
NOTES:
DSCLK and DSI are synchronized internally. D4 is measured from the
synchronized DSCLK input relative to the rising edge of CLKOUT.
1
Figure 24 shows real-time trace timing for the values in Table 44.
PSTCLK
DE0
DE1
DE2
PST[3:0]
DDATA[3:0]
Figure 24. Real-Time Trace AC Timing
Figure 25 shows BDM serial port AC timing for the values in Table 44.
CLKOUT
DE6
BKPT
DE7
DE5
DSCLK
DE3
DSI
Current
Next
DE4
DSO
Past
Current
Figure 25. BDM Serial Port AC Timing
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
54
Freescale Semiconductor
Documentation
9
Documentation
Table 45 lists the documents that provide a complete description of the MCF5271 and their development
support tools. Documentation is available from a local Freescale distributor, a Freescale semiconductor
sales office, the Freescale Literature Distribution Center, or through the Freescale world-wide web address
at http://www.freescale.com.
Table 45. MCF5271 Documentation
Freescale
Document
Number
9.1
Title
Revision
Status
MCF5271EC
MCF5271 RISC Microprocessor Hardware
Specifications
Rev. 1.2
This document
MCF5271RM
MCF5271 Reference Manual
1.1
Available
MCF5271PB
MCF5271 Product Brief
0
Available
MCF5271FS
MCF5271 Fact Sheet
—
In Process
CFPRODFACT/D
The ColdFire Family of 32-Bit Microprocessors
Family Overview and Technology Roadmap
0
Available under
NDA
MCF5xxxWP
MCF5xxxWP WHITE PAPER: Motorola ColdFire
VL RISC Processors
0
Available under
NDA
MAPBGAPP
MAPBGA 4-Layer Example
0
Available
CFPRM/D
ColdFire Family Programmer's Reference Manual
2
Available
Document Revision History
Table 46 provides a revision history for this document.
Table 46. Document Revision History
Rev. No.
Substantive Change(s)
0
Initial release
1
- Fixed several clock values.
- Updated Signal List table
1.1
- Removed duplicate information in the module description sections. The information is all in the
Signals Description Table.
1.2
- Removed detailed signal description section. This information can be found in the MCF5235RM
Chapter 2.
- Removed detailed feature list. This information can be found in the MCF5235RM Chapter 1.
- Changed instances of Motorola to Freescale
- Added values for ‘Maximum operating junction temperature’ in Table 27.
- Added typical values for ‘Core operating supply current (master mode)’ in Table 28.
- Added typical values for ‘Pad operating supply current (master mode)’ in Table 28.
- Removed unnecessary PLL specifications, #6-9, in Table 29.
MCF5271 Integrated Microprocessor Hardware Specification, Rev. 1.2
Freescale Semiconductor
55
HOW TO REACH US:
USA/Europe/Locations not listed:
Freescale Semiconductor Literature Distribution
P.O. Box 5405, Denver, Colorado 80217
1-800-521-6274 or 480-768-2130
Japan:
Freescale Semiconductor Japan Ltd.
Technical Information Center
3-20-1, Minami-Azabu, Minato-ku
Tokyo 106-8573, Japan
81-3-3440-3569
Asia/Pacific:
Freescale Semiconductor H.K. Ltd.
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T. Hong Kong
852-26668334
Learn More:
For more information about Freescale
Semiconductor products, please visit
http://www.freescale.com
Information in this document is provided solely to enable system and software implementers to use
Freescale Semiconductor products. There are no express or implied copyright licenses granted
hereunder to design or fabricate any integrated circuits or integrated circuits based on the information
in this document.
Freescale Semiconductor reserves the right to make changes without further notice to any products
herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the
suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any
and all liability, including without limitation consequential or incidental damages. “Typical” parameters
which may be provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating parameters,
including “Typicals” must be validated for each customer application by customer’s technical experts.
Freescale Semiconductor does not convey any license under its patent rights nor the rights of others.
Freescale Semiconductor products are not designed, intended, or authorized for use as components
in systems intended for surgical implant into the body, or other applications intended to support or
sustain life, or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer purchase or use
Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall
indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney
fees arising out of, directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was
negligent regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other
product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2004.
MCF5271EC
Rev. 1.2, 12/2004