PI3CH200 Low Voltage, 5Ω, 2-Channel 2-Port NanoSwitch™ Features Description • • • • • • • • • • • The PI3CH200 is a low voltage, 2-channel switch designed with fast individual enables. The switch introduces no additional propagation delay or additional ground bounce noise. Near-zero propagation delay 5Ω switches connect inputs to outputs High signal passing bandwidth (500 MHz) Beyond Rail-to-Rail switching 5V I/O tolerant with 3.3V supply in OFF and ON state 2.5V and 3.3V supply voltage operation Hot Insertion Capable Industrial Operating Temperature: –40ºC to +85ºC 2kV ESD Protection (human body model) Latch-up Performance: >250mA per JESD17 Packaging (Pb-free & Green Available): – 8-pin TSSOP (L) The PI3CH200 device has active LOW enables. It is very useful in switching signals that have high bandwidth (500 MHz). Applications • • • • High Bandwidth Data Switching Hot-Docking Analog Signal Switching Differential Signal Switching Pin Configuration Block Diagram B1 A1 ��� � � ��� �� � � ��� �� � � �� ��� � � �� EN1 A2 B2 EN2 Pin Description Truth Table(1) ENx Ax Bx VCC Function X Hi-Z Hi-Z GND Disconnect H Hi-Z Hi-Z VCC Disconnect L Bx Ax VCC Connect Pin Name ENx Notes: 1. H = High Voltage Level, L = Low Voltage Level, Hi-Z = High-Impedance 06-0246 1 Description Switch Enable A2 - A1 A Ports B2 - B1 B Ports GND Ground VCC Power PS8721C 05/10/06 PI3CH200 Low Voltage, 5Ω, 2-Channel 2-Port NanoSwitch™ Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................................ –65°C to +150°C Ambient Temperature with Power Applied ............... –40°C to +85°C Supply Voltage to Ground Potential ........................... –0.5V to +4.6V DC Input Voltage ........................................................ –0.5V to +6.0V DC Output Current................................................................... 120mA Power Dissipation ....................................................................... 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics, 3.3V Supply (Over Operating Range, TA = –40°C to +85°C, VCC = 3.3V ± 10%) Parameters Description Test Conditions(1) Min. Typ.(2) Max. Units 0.8 V VIH Input HIGH Voltage Guaranteed Logic HIGH Level 2 VIL Input LOW Voltage Guaranteed Logic LOW Level –0.5 VIK Clamp Diode Voltage VCC = Min., IIN = –18mA IIH Input HIGH Current VCC = Max., VIN = VCC ±1 IIL Input LOW Current VCC = Max., VIN = GND ±1 0 ≤ A, B ≤ VCC ±1 IOZH RON High-Impedence Switch Current(3) On-resistance(4) –1.3 –1.8 VCC = Min.,VIN = 0.0V ION = –48mA or –64mA 4 6 VCC = Min., VIN = 3.6V, ION = –15mA 5 8 µA Ω Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (A,B) pins. 06-0246 2 PS8721C 05/10/06 PI3CH200 Low Voltage, 5Ω, 2-Channel 2-Port NanoSwitch™ DC Electrical Characteristics, 2.5V Supply (Over Operating Range, TA = –40°C to +85°C, VCC = 2.5V ± 10%) Parameters Test Conditions(1) Description Min. Typ.(2) Max. VIH Input HIGH Voltage Guaranteed Logic HIGH Level 1.8 VCC + 0.3 VIL Inout LOW Voltage Guaranteed Logic LOW Level –0.3 0.8 VIK Clamp Diode Voltage VCC = Max., IIN = –6mA IIH Input HIGH Current VCC = Max., VIN = VCC ±1 IIL Input LOW Current VCC = Max., VIN = GND ±1 0 ≤ A, B ≤ VCC ±1 IOZH RON High Impedance Current(3) Switch On Resistance(4) –0.7 VCC = Min., VIN =0.0V, ION = –48mA 6 VCC = Min., VIN = 2.25V, ION = –15mA 7 Units V –1.8 µA 8 Ω 14 Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (A,B) pins. Capacitance (TA = 25°C f = 1 MHz) Parameters(1) Description CIN Input Capacitance COFF A/B Capacitance, Switch Off CON A/B Capacitance, Switch On Test Conditions Typ. Units 3.5 VIN = 0V 3.5 pF 7.0 Notes: 1. This parameter is determined by device characterization but is not production tested. Power Supply Characteristics Parameters Description ICC Quiescent Power Supply Current Test Conditions(1) VCC = 3.6V, VIN = GND or VCC Min. Typ.(2) Max. 0.8 Units mA Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 3.3V, +25°C ambient. 06-0246 3 PS8721C 05/10/06 PI3CH200 Low Voltage, 5Ω, 2-Channel 2-Port NanoSwitch™ Dynamic Electrical Characteristics Over the Operating Range (TA = –40º to +85º, VCC = 3.3V ± 10%) Parameter Description Test Condition Min. Typ. XTALK Crosstalk See Test Diagram –60 OIRR Off-Isolation See Test Diagram –60 BW –3dB Bandwidth See Test Diagram 200 Max. Units dB 500 MHz Switching Characteristics over 3.3V Operating Range Parameters Conditions(1) Description tPLH tPHL Propagation Delay(2,3) Ax to Bx, Bx to Ax tPZH tPZL Enable Time ENx to Ax or Bx tPHZ tPLZ Disable Time ENx to Ax or Bx Com. Min. Typ. Max. See Test Diagram Units 0.3 1.5 9.0 1.5 9.0 ns See Test Diagram Notes: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Switching Characteristics over 2.5V Operating Range Parameters Conditions(1) Description tPLH tPHL Propagation Delay(2,3) Ax to Bx, Bx to Ax tPZH tPZL Enable Time ENx to Ax or Bx tPHZ tPLZ Disable Time ENx to Ax or Bx Com. Min. See Test Diagram Max. Units 0.3 1.5 15.0 1.5 12.0 ns See Test Diagram Notes: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 06-0246 4 PS8721C 05/10/06 PI3CH200 Low Voltage, 5Ω, 2-Channel 2-Port NanoSwitch™ Test Circuit for Electrical Characteristics 6.0V VCC 200Ω Pulse Generator VIN VOUT D.U.T 10pF CL RT 200Ω Notes: • CL = Load capacitance: includes jig and probe capacitance. • RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. • Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. • Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. • All input impulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50-ohm, tR ≤ 2.5ns, tF ≤ 2.5ns. • The outputs are measured one at a time with one transition per measurement. Switch Positions Test Switch tPLZ, tPZL 6.0V tPHZ, tPZH GND Prop Delay Open Test Circuit for Dynamic Electrical Characteristics �� ������� ��� �� ����� �������� 06-0246 �� ���� 5 ��� PS8721C 05/10/06 PI3CH200 Low Voltage, 5Ω, 2-Channel 2-Port NanoSwitch™ Switching Waveforms 2.5V ENx 1.25V 1.25V 0V 3.5V 2.5V Input tPLH Output Output 2.5V tPHL tPLZ VDD/2 1.5V VOH 2.5V tPZL VOL Output VOL +0.3V VOL tPHZ tPZH 2.5V VOH VOH VDD/2 VOH -0.3V VOL Voltage Waveforms Enable and Disable Times 3.5V 2.5V Input tPLH tPHL 1.5V VOH 2.5V Output VOL tSK(p) = I tPHL – tPLH I Pulse Skew - tSK(p) 06-0246 6 PS8721C 05/10/06 PI3CH200 Low Voltage, 5Ω, 2-Channel 2-Port NanoSwitch™ Applications Information Logic Inputs The logic control inputs can be driven upto 3.6V regardless of the supply voltage. For example, given a +3.3V supply, EN may be driven LOW to 0V and HIGH to 3.6V. Driving EN Rail-to-Rail® minimizes power consumption. Power Supply-Sequencing Proper power supply sequencing is recommended for all CMOS devices. Always apply VCC before applying signals to the input/ output or control pins. Hot Insertion For Datacom and Telecom applications that have ten or more volts passing through the backplane, a high voltage from the power supply may be seen at the device input pins during hot insertion. The PI3CHxx devices have maximum limits of 6V and 120mA for 20ns. If the power is higher or applied for a longer time or repeatedly reaches the maximum limits, the devices can be damaged. Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. Packaging Mechanical: 8-pin TSSOP (L) �������������������� ��������� ������������ ��������������� � Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com Note: 1. Package Outline Exclusive of Mold Flash and Metal Burr 2. Controlling dimentions in millimeters 3. Ref: JEDEC MO-153F/AA ��������������������������������������� ���������������� 06-0246 7 PS8721C 05/10/06 PI3CH200 Low Voltage, 5Ω, 2-Channel 2-Port NanoSwitch™ Ordering Information Ordering Code PI3CH200L PI3CH200LE Packaging Code L L Package Description 173-mil, 8-pin TSSOP Pb-free & Green, 173-mil, 8-pin TSSOP Notes: • Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ • E = Pb-free & Green • Adding an X suffix = Tape/Reel Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com 06-0246 8 PS8721C 05/10/06