PI5C3861 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 10-Bit, 2-Port Bus Switch Product Features: Product Description: Near zero propagation delay 5ohm switches connect inputs to outputs Direct bus connection when switches are ON Ultra Low Quiescent Power (0.2 µA Typical) Ideally suited for notebook applications Packages available: 24-pin 150 mil wide plastic QSOP (Q24) 24-pin 300 mil wide plastic SOIC (S24) Pioneer Semiconductors PI5C series of logic circuits are pro-duced in the Companys advanced submicron CMOS technology, achieving industry leading performance. The PI5C3861 is a 10-bit, 2-port bus switch designed with a low ON resistance (5ohm) allowing inputs to be connected directly to outputs. The bus switch creates no additional propagational delay or additional ground bounce noise. The switches are turned ON by the Bus Enable (BE) input signal. Product Pin Configuration Logic Block Diagram A0 B0 A9 B9 BE C0 A0 B0 D0 C1 A1 B1 D1 BX0 BX1 GND 24 1 23 2 22 3 21 4 5 24-Pin 20 6 Q,S 19 18 7 17 8 16 9 15 10 14 11 13 12 Vcc D3 B3 A3 C3 D2 B2 A2 C2 NC BX3 BX2 BE Product Pin Description Pin Name BE A09 B09 GND VCC Truth Table(1) Function Disconnect Connect BE H L A09 Hi-Z B09 Description Bus Enable Input (Active LOW) Bus A Bus B Ground Power NOTE: 1. H = High Voltage Level L = Low Voltage Level Hi-Z = High Impedance 1 PS7021A 12/27/00 PI5C3861 10-Bit, 2-Port Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................................................. 55°C to +125°C Ambient Temperature with Power Applied ................................ 40°C to +85°C Supply Voltage to Ground Potential (Inputs & Vcc Only) .......... 0.5V to +7.0V Supply Voltage to Ground Potential (Outputs & D/O Only) ....... 0.5V to +7.0V DC Input Voltage ......................................................................... 0.5V to +7.0V DC Output Current ................................................................................... 120 mA Power Dissipation ......................................................................................... 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (Over the Operating Range, TA = 40°C to +85°C, VCC = 5V ±5%) Parameters Description Test Conditions(1) Min. VIH Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 VIL Input LOW Voltage Guaranteed Logic LOW Level 0.5 IIH Input HIGH Current IIL Typ(2) Max. Units V 0.8 V VCC = Max., VIN = VCC ±1 µA Input LOW Current VCC = Max., VIN = GND ±1 µA IOZH High Impedance Output Current 0 A, B VCC ±1 µA VIK Clamp Diode Voltage VCC = Min., IIN = 18 mA 0.7 IOS Short Circuit Current A (B) = 0V, B (A) = VCC 100 VH Input Hysteresis at Control Pins RON Switch On Resistance (3) (4) 1.2 V mA 150 VCC = Min., VIN = 0.0V, VCC = Min., VIN = 2.4V, ION = 48 mA ION = 15 mA mV 5 10 7 15 ohm Capacitance (TA = 25°C, f = 1 MHz) Parameters(5) Description Test Conditions CIN COFF Input Capacitance A/B Capacitance, Switch Off CON A/B Capacitance, Switch On Typ Max. Units VIN = 0V VIN = 0V 6 6 pF pF VIN = 0V 8 pF Notes: 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc = 5.0V, TA = 25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. 5. This parameter is determined by device characterization but is not production tested. 2 PS7021A 12/27/00 PI5C3861 10-Bit, 2-Port Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Power Supply Characteristics Test Conditions(1) Parameters Description Min. ICC Quiescent Power Supply Current VCC = Max. VIN = GND or VCC ÐICC Supply Current per Input @ TTL HIGH VCC = Max. VIN = 3.4V(3) ICCD Supply Current per Input per MHz(4) VCC = Max., A and B Pins Open BE = GND Control Input Toggling 50% Duty Cycle Typ(2) Max. Units 0.1 10 µA 2.5 mA 0.25 mA/ MHz Switching Characteristics over Operating Range Com. tPLH tPHL tPZH tPZL tPHZ tPLZ Conditions(1) Propagation Delay(2,3) Ax to Bx, Bx to Ax Bus Enable Time BE to Ax or Bx Bus Disable Time BE to Ax or Bx CL = 50 pF RL = 500ohm 3 Min 5 6 7 PI5C3861 Description 2 4 Notes: 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at Vcc = 5.0V, +25°C ambient. 3. Per TTL driven input (VIN = 3.4V, control inputs only); A and B pins do not contribute to Icc. 4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant AC or DC currents as they transition. This parameter is not tested, but is guaranteed by design. Parameters 1 Max Unit 0.25 ns 1.5 6.5 ns 1.5 5.5 ns 8 9 10 Notes: 1. See test circuit and wave forms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25 ns for 50 pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 11 12 13 14 15 Pericom Semiconductor Corporation 2380 Bering Drive San Jose, CA 95131 1-800-435-2336 Fax (408) 435-1100 http://www.pericom.com 3 PS7021A 12/27/00