RICOH R2033T-E2

R2033K/T
3 wire interface Real-Time Clock ICs
NO.EA-120-070221
OUTLINE
The R2033K/T is a CMOS real-time clock IC connected to the CPU by three signal lines, CE, SCLK, SIO, and
configured to perform serial transmission of time and calendar data to the CPU. The periodic interrupt circuit is
configured to generate interrupt signals with six selectable interrupts ranging from 0.5 seconds to 1 month. The
2 alarm interrupt circuits generate interrupt signals at preset times. As the oscillation circuit is driven under
constant voltage, fluctuation of the oscillator frequency due to supply voltage is small, and the time keeping
current is small (TYP. 0.45µA at 3V). The oscillation halt sensing circuit can be used to judge the validity of
internal data in such events as power-on; The supply voltage monitoring circuit is configured to record a drop in
supply voltage below two selectable supply voltage monitoring threshold settings. The 32.768kHz clock output
function (CMOS output with control pin) is intended to output sub-clock pulses for the external microcomputer.
The oscillation adjustment circuit is intended to adjust time counts with high precision by correcting deviations in
the oscillation frequency of the crystal oscillator. Since the package for these ICs are TSSOP10G (4.0x2.9x1.0:
R2033T) or FFP12 (2.0x2.0x1.0: R2033K), high density mounting of ICs on boards is possible.
FEATURES
• Minimum Timekeeping supply voltage TYP:0.66 to 5.5v (Worst: 1.00V to 5.5v); VDD pin
• Low power consumption
0.45µA TYP at VDD=3V (1.00µA MAX.)
• Three signal lines (CE, SCLK, SIO) required for connection to the CPU.
(Maximum clock frequency of 1MHz (with VDD = 3V) )
• Time counters (counting hours, minutes, and seconds) and calendar counters (counting years, months, days,
and weeks) (in BCD format)
• Interrupt circuit configured to generate interrupt signals (with interrupts ranging from 0.5 seconds to 1 month)
to the CPU and provided with an interrupt flag and an interrupt halt
• 2 alarm interrupt circuits (Alarm_W for week, hour, and minute alarm settings and Alarm_D for hour and
minute alarm settings)
• With Power-on flag to prove that the power supply starts from 0V
• 32-kHz clock output pin (CMOS push-pull output with control pin)
• Supply voltage monitoring circuit with two supply voltage monitoring threshold settings
• Automatic identification of leap years up to the year 2099
• Selectable 12-hour and 24-hour mode settings
• High precision oscillation adjustment circuit
• Built-in oscillation stabilization capacitors (CG and CD)
• Package TSSOP10G (4.0mm x 2.9mm x 1.0mm: R2033T) FFP12 (2.0mm x 2.0mm x 1.0mm: R2033K)
• CMOS process
1
R2033K/T
PIN CONFIGURATION
R2033T(TSSOP10G)
R2033K(FFP12)
4
7
CLKC
VSS
5
6
INTR
TOP VIEW
11
5
(VSS)
CE
12
4
(VSS)
3
CE
VSS
32KOUT
OSCOUT
VDD
2
8
6
SCLK
3
10
1
SIO
INTR
SIO
OSCIN
7
9
8
2
OSCIN
SCLK
OSCOUT
10
9
1
CLKC
VDD
32KOUT
TOP VIEW
BLOCK DIAGRAM
32KOUT
32kHz
OUTPUT
CONTROL
CLKC
OSCIN
OSC
DIVIDER
CORREC
-TION
COMPARATOR_W
ALARM_W REGISTER
(MIN,HOUR, WEEK)
COMPARATOR_D
ALARM_D REGISTER
(MIN,HOUR)
DIV
TIME COUNTER
(SEC,MIN,HOUR,WEEK,DAY,MONTH,YEAR)
VDD
VOLTAGE
DETECT
POWER_ON
RESET
VSS
OSCOUT
OSC
DETECT
INTR
ADDRESS
DECODER
INTERRUPT CONTROL
ADDRESS
REGISTER
SHIFT REGISTER
SELECTION GUIDE
Part Number is designated as follows:
R2033K-E2 ←Part Number
↑↑
R2033a-cc
Code
a
bb
2
Description
Designation of the package.
K: FFP12
T: TSSOP10G
Designation of the taping type. Only E2 is available.
SCLK
I/O
CONTROL
SIO
CE
R2033K/T
PIN DESCRIPTION
Symbol
CE
Item
Chip enable
Input
SCLK
Serial Clock
Input
SIO
INTR
Serial Input /
Output
Interrupt
Output
32KOUT
32kHz Clock
Output
CLKC
Clock Control
OSCIN
OSCOUT
Oscillation
Circuit
Input / Output
Positive/Negative
Power
Supply Input
VDD
VSS
(VSS)
Description
The CE pin is used for interfacing with the CPU. Should be held high to
allow access to the CPU. Incorporates a pull-down resistor. Should be
held low or open when the CPU is powered off. Allows a maximum input
voltage of 5.5v regardless of supply voltage.
The SCLK pin is used to input clock pulses synchronizing the input and
output of data to and from the SIO pin. Allows a maximum input voltage of
5.5v regardless of supply voltage.
The SIO pin is used to input and output data intended for writing and reading
in synchronization with the SCLK pin. CMOS input / output.
The INTR pin is used to output alarm interrupt (Alarm_W) and alarm
interrupt (Alarm_D) and output periodic interrupt signals to the CPU.
Disabled at power-on from 0V. N-channel open drain output. Allows a
maximum pull-up voltage of 5.5v regardless of supply voltage.
The 32KOUT pin is used to output 32.768-kHz clock pulses. The pin is
CMOS push-pull output. The output is disabled and held “L” when CLKC
pin is set to “L” or open, or certain register setting. This pin is enabled at
power-on from 0v.
The CLKC pin is used to control output of the 32KOUT pin. The clock
output is disabled and held “L” when this pin is set to “L” or open.
Incorporated pull down register.
The OSCIN and OSCOUT pins are used to connect the 32.768-kHz crystal
oscillator (with all other oscillation circuit components built into the
R2033K/T).
The VDD pin is connected to the power supply. The VSS pin is grounded.
Please connect to ground line, or do not connect any lines.
3
R2033K/T
ABSOLUTE MAXIMUM RATINGS
(VSS=0V)
Symbol
Item
VDD
Supply Voltage
VI
Input Voltage 1
Input Voltage 2
VO
Output Voltage 1
Output Voltage 2
PD
Power Dissipation
Topt
Operating Temperature
Tstg
Storage Temperature
Pin Name
VDD
CE, SCLK, CLKC
SIO
SIO, 32KOUT
INTR
Topt = 25°C
Description
-0.3 to +6.5
-0.3 to +6.5
-0.3 to VDD + 0.3
-0.3 to VDD + 0.3
-0.3 to +6.5
300
-40 to +85
-55 to +125
Unit
V
V
V
mW
°C
°C
RECOMMENDED OPERATING CONDITIONS
Symbol
Vaccess
Item
Supply Voltage
VCLK
Time keeping Voltage
VCLKL
Minimum Time keeping
Voltage
Oscillation Frequency
Pull-up Voltage
fXT
VPUP
Pin Name
Power supply voltage
for interfacing
with CPU
CGout,CDout=0pF
*1), *2)
CGout,CDout=0pF
*1), *2)
(VSS=0V, Topt=-40 to +85°C)
Min,
Typ.
Max.
Unit
1.7
5.5
V
1.00
5.50
0.66
1.00
kHz
5.5
V
VDD
+0.3
*1) CGout is connected between OSCIN and VSS, CDout is connected between OSCOUT and VSS.
R2033K/T incorporates the capacitors between OSCIN and VSS, between OSCOUT and VSS.
Then normally, CGout and CDout are not necessary. For more detail, see “P.32 •Oscillation Adjustment
Circuit”
*2) Crystal oscillator: CL=6-9pF, R1=50KΩ
4
32.768
V
INTR
32KOUT
R2033K/T
DC ELECTRICAL CHARACTERISTICS
•
R2033K/T
(Unless otherwise specified:
VSS=0V, VDD=3.0V, Topt=-40 to +85°C, Crystal oscillator 32768Hz,CL=7pF,R1=50kΩ)
Symbol
Item
Pin Name
Conditions
Min.
Typ.
“H” Input Voltage
VIH1
CE, SCLK, VDD=1.7 to 5.5V
0.8x
CLKC
VDD
VIH2
SIO
0.8x
VDD
-0.3
VIL
“L” Input Voltage
CE, SCLK,
CLKC, SIO
IOH
“H” Output
SIO,
VOH=VDD-0.5V
Current
32KOUT
VOL=0.4V
2.0
IOL1
“L” Output
INTR
Current
0.5
IOL2
SIO,
32KOUT
IIL
Input Leakage
SCLK
VI=5.5V or VSS
-1.0
Current
VDD=5.5V
RDNCE
Pull-down Resistance
CE
40
120
ICLKC
Pull-down Resister
CLKC
VI=5.5V
0.30
Input Leakage Current
IOZ1
SIO
VO=5.5V or VSS
-1
Output Off-state
VDD=5.5V
Current
VO=5.5V
IOZ2
-1
INTR
VDD=5.5V
IDD
Time Keeping Current
VDD
VDD=3V,
CE=SCLK=SIO=CLKC
0.45
= INTR =0V
32KOUT=OFF
Output = OPEN
CGout=CDout=0pF
*1)
VDETH
Supply Voltage
VDD
1.45
1.60
Topt=-30 to +70°C
Monitoring Voltage “H”
VDETL
Supply Voltage
VDD
1.15
1.30
Topt=-30 to +70°C
Monitoring Voltage “L”
*1) For time keeping current when outputting 32.768kHz from the 32KOUT pin, see “P.44
CHARACTERISTICS”. For time keeping current when CGOUT, CDOUT is not equal to 0pF,
•Adjustment of oscillation frequency”.
Max.
5.5
Unit
VDD+0.
3
0.2x
VDD
-0.5
V
mA
mA
1.0
µA
400
1.00
kΩ
µA
1
µA
1
1.00
µA
1.75
V
1.45
V
TYPICAL
see “P.29
5
R2033K/T
AC ELECTRICAL CHARACTERISTICS
Unless otherwise specified: VSS=0V,Topt=-40 to +85°C
Input and Output Conditions: VIH=0.8×VDD,VIL=0.2×VDD,VOH=0.8×VDD,VOL=0.2×VDD,CL=50pF
Sym
Item
CondiVDD≥1.7V
-bol
Tions
Min.
Typ.
Max.
tCES
CE Set-up Time
400
tCEH
CE Hold Time
400
tCR
CE Recovery Time
62
fSCLK
SCLK Clock Frequency
1.0
tCKH
SCLK Clock ”H” Time
400
tCKL
SCLK Clock ”L” Time
400
tCKS
SCLK Set-up Time
200
tRD
Data Output Delay Time
300
tRZ
Data Output Floating Time
300
tCEZ
Data Output Delay Time After
300
Falling of CE
tDS
Input Data Set-up Time
200
tDH
Input Data Hold Time
200
Time
tDELAY
Output Delay Time of Voltage
100
105
110
Keeping
Detector
tCKH
Unit
ns
ns
µs
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ms
tCKL
CE
tCEH
tCKS
tCR
tCES
SCLK
tDS
tDH
tCEZ
SIO(write cycle)
SIO(read cycle)
tRD
tRD
tRZ
*) For reading/writing timing, see “P.26 •Considerations in Reading and Writing Time Data under special
condition”.
6
R2033K/T
PACKAGE DIMENSIONS
R2033K
9
7
6
10
1PIN INDEX
12
0.2±0.15
0.35
0.25
1.0Max
2.0±0.1
3
2PIN INDEX
0.35
0.3±0.15
0.103
0.5
0.05
4
1
0.5
•
(BOTTOM VIEW)
0.17±0.1
0.27±0.15
2.0±0.1
unit: mm
7
R2033K/T
R2033T
0 to 10°
1
5
0.5
+0.1
0.15 M
+0.1
0.1 -0.05
(0.75)
0.13 -0.05
0.1
0.2±0.1
0.55±0.2
6
2.8±0.2
10
4.0±0.2
2.9±0.2
0.85±0.15
•
unit: mm
TAPING SPECIFICATION
The R2033K/T have one designated taping direction. The product designation for the taping components is
"R2033K/T-E2".
8
R2033K/T
GENERAL DESCRIPTION
•
Interface with CPU
The R2033K/T is connected to the CPU by three signal lines CE (Chip Enable), SCLK (Serial Clock), and SIO
(Serial Input and Output), through which it reads and writes data from and to the CPU. The CPU can be
accessed when the CE pin is held high. Access clock pulses have a maximum frequency of 1 MHz allowing
high-speed data transfer to the CPU.
•
Clock and Calendar Function
The R2033K/T reads and writes time data from and to the CPU in units ranging from seconds to the last two
digits of the calendar year. The calendar year will automatically be identified as a leap year when its last two
digits are a multiple of 4. Consequently, leap years up to the year 2099 can automatically be identified as such.
*) The year 2000 is a leap year while the year 2100 is not a leap year.
•
Alarm Function
The R2033K/T incorporates the alarm interrupt circuit configured to generate interrupt signals to the CPU at
preset times. The alarm interrupt circuit allows two types of alarm settings specified by the Alarm_W registers
and the Alarm_D registers. The Alarm_W registers allow week, hour, and minute alarm settings including
combinations of multiple day-of-week settings such as "Monday, Wednesday, and Friday" and "Saturday and
Sunday". The Alarm_D registers allow hour and minute alarm settings. The Alarm_W outputs from INTR pin,
and the Alarm_D outputs also from /INTR pin. Each alarm function can be checked from the CPU by using a
polling function.
•
High-precision Oscillation Adjustment Function
The R2033K/T has built-in oscillation stabilization capacitors (CG and CD), which can be connected to an
external crystal oscillator to configure an oscillation circuit. Two kinds of accuracy for this function are
alternatives. To correct deviations in the oscillator frequency of the crystal, the oscillation adjustment circuit is
configured to allow correction of a time count gain or loss (up to ±1.5ppm or ±0.5ppm at 25°C) from the CPU.
The maximum range is approximately ±189ppm (or ±63ppm) in increments of approximately 3ppm (or 1ppm).
Such oscillation frequency adjustment in each system has the following advantages:
* Allows timekeeping with much higher precision than conventional RTCs while using a crystal oscillator with a
wide range of precision variations.
* Corrects seasonal frequency deviations through seasonal oscillation adjustment.
* Allows timekeeping with higher precision particularly with a temperature sensing function out of RTC, through
oscillation adjustment in tune with temperature fluctuations.
•
Power-on Reset, Oscillation Halt Sensing Function and Supply Voltage Monitoring Function
The R2033K/T incorporates an oscillation halt sensing circuit equipped with internal registers configured to
record any past oscillation halt.
Power on reset function reset the control resisters when the system is powered on from 0V. At the same time,
the fact is memorized to the resister as a flag, thereby identifying whether they are powered on from 0V or
battery backed-up.
The R2033K/T also incorporates a supply voltage monitoring circuit equipped with internal registers configured
to record any drop in supply voltage below a certain threshold value. Supply voltage monitoring threshold
9
R2033K/T
settings can be selected between 1.6V and 1.3V through internal register settings. The sampling rate is normally
1s.
The oscillation halt sensing circuit and the power-on reset flag are configured to confirm the established
invalidation of time data in contrast to the supply voltage monitoring circuit intended to confirm the potential
invalidation of time data. Further, the supply voltage monitoring circuit can be applied to battery supply voltage
monitoring.
•
Periodic Interrupt Function
The R2033K/T incorporates the periodic interrupt circuit configured to generate periodic interrupt signals aside
from interrupt signals generated by the alarm interrupt circuit for output from the INTR pin. Periodic interrupt
signals have five selectable frequency settings of 2 Hz (once per 0.5 seconds), 1 Hz (once per 1 second), 1/60
Hz (once per 1 minute), 1/3600 Hz (once per 1 hour), and monthly (the first day of every month). Further,
periodic interrupt signals also have two selectable waveforms, a normal pulse form (with a frequency of 2 Hz or 1
Hz) and special form adapted to interruption from the CPU in the level mode (with second, minute, hour, and
month interrupts). The condition of periodic interrupt signals can be monitored with using a polling function.
•
32kHz Clock Output
The R2033K/T incorporates a 32-kHz clock circuit configured to generate clock pulses with the oscillation
frequency of a 32.768kHz crystal oscillator for output from the 32KOUT pin. The 32KOUT pin is CMOS push-pull
output and the output is enabled and disabled when the CLKC pin is held high, and low or open, respectively.
The 32-kHz clock output can be disabled by certain register settings but cannot be disabled without manipulation
of any two registers with different addresses to prevent disabling in such events as the runaway of the CPU.
The 32-kHz clock circuit is enabled at power-on, when the CLKC pin is held high.
10
R2033K/T
Address Mapping
Address
A3A2A1A0
0
0000
Register Name
Second Counter
1
2
0001
0010
Minute Counter
Hour Counter
3
4
5
0011
0100
0101
6
7
0110
0111
8
1000
9
1001
A
1010
B
1011
C
1100
D
E
1101
1110
Control Register 1 *3)
F
1111
Control Register 2 *3)
Day-of-week Counter
Day-of-month Counter
Month Counter and
Century Bit
Year Counter
Oscillation Adjustment
Register *3)
Alarm_W
(Minute Register)
Alarm_W
(Hour Register)
Alarm_W
(Day-of-week Register)
Alarm_D
(Minute Register)
Alarm_D
(Hour Register)
D a
D4
S10
t a
D3
S8
D2
S4
D1
S2
D0
S1
M10
H10
M8
H8
M4
H4
M2
H2
M1
H1
D8
MO8
W4
D4
MO4
W2
D2
MO2
W1
D1
MO1
Y10
F4
Y8
F3
Y4
F2
Y2
F1
Y1
F0
WM20
WM10
WM8
WM4
WM2
WM1
WH10
WH8
WH4
WH2
WH1
WW6
WH20
WP/ A
WW5
WW4
WW3
WW2
WW1
WW0
-
DM40
DM20
DM10
DM8
DM4
DM2
DM1
-
-
DH4
DH2
DH1
WALE
DH20 DH10
DH8
A
DP/
DALE 12 /24 CLEN2 TEST
CT2
CT1
CT0
VDSL
VDET
D7
*2)
-
D6
S40
D5
S20
M40
-
19 /20
-
M20
H20
P/ A
D20
-
D10
MO10
Y80
DEV
*4)
-
Y40
F6
Y20
F5
WM40
-
-
-
XST
PON
*5)
CLEN1 CTFG WAFG DAFG
Notes:
* 1) All the data listed above accept both reading and writing.
* 2) The data marked with "-" is invalid for writing and reset to 0 for reading.
* 3) When the PON bit is set to 1 in Control Register 2, all the bits are reset to 0 in Oscillation Adjustment
Register, Control Register 1 and Control Register 2 excluding the XST bit.
* 4) When DEV=0, the oscillation adjustment circuit is configured to allow correction of a time count gain
or loss up to ±1.5ppm.
When DEV=1, the oscillation adjustment circuit is configured to allow correction of a time count gain
or loss up to or ±0.5ppm.
* 5) PON is a power-on-reset flag.
11
R2033K/T
Register Settings
•
Control Register 1 (ADDRESS Eh)
D7
D6
D5
D4
D3
D2
D1
D0
TEST
CT2
CT1
CT0
(For Writing)
WALE
DALE
12 /24
CLEN2
WALE
DALE
TEST
CT2
CT1
CT0
(For Reading)
12 /24
CLEN2
0
0
0
0
0
0
0
0
Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
(1) WALE, DALEAlarm_W Enable Bit, Alarm_D Enable Bit
WALE,DALE
0
1
Description
Disabling the alarm interrupt circuit (under the control of the settings
of the Alarm_W registers and the Alarm_D registers).
Enabling the alarm interrupt circuit (under the control of the settings
of the Alarm_W registers and the Alarm_D registers)
12 /24-hour Mode Selection Bit
Description
12 /24
0
Selecting the 12-hour mode with a.m. and p.m. indications.
1
Selecting the 24-hour mode
Setting the 12 /24 bit to 0 and 1 specifies the 12-hour mode and the 24-hour mode, respectively.
(Default)
(2) 12 /24
24-hour mode
12-hour mode
24-hour mode
00
12 (AM12)
12
01
01 (AM 1)
13
02
02 (AM 2)
14
03
03 (AM 3)
15
04
04 (AM 4)
16
05
05 (AM 5)
17
06
06 (AM 6)
18
07
07 (AM 7)
19
08
08 (AM 8)
20
09
09 (AM 9)
21
10
10 (AM10)
22
11
11 (AM11)
23
Setting the 12 /24 bit should precede writing time data
(3) CLEN2
(Default)
12-hour mode
32 (PM12)
21 (PM 1)
22 (PM 2)
23 (PM 3)
24 (PM 4)
25 (PM 5)
26 (PM 6)
27 (PM 7)
28 (PM 8)
29 (PM 9)
30 (PM10)
31 (PM11)
32kHz Clock Output Bit 2
Description
CLEN2
0
Enabling the 32-kHz clock circuit
(Default)
1
Disabling the 32-kHz clock circuit
Setting the CLEN2 bit or the CLEN1 bit (D3 in the control register 2) to 0, and the CLKC pin to high
specifies generating clock pulses with the oscillation frequency of the 32.768-kHz crystal oscillator for
output from the 32KOUT pin. Conversely, setting both the CLEN1 and CLEN2 bit to 1 or CLKC pin to
low specifies disabling (”L”) such output.
12
R2033K/T
(4) TEST
Test Bit
TEST
Description
0
Normal operation mode.
1
Test mode.
The TEST bit is used only for testing in the factory and should normally be set to 0.
(5) CT2,CT1, and CT0
CT2
CT1
(Default)
Periodic Interrupt Selection Bits
CT0
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
Wave form
mode
Pulse Mode
*1)
Pulse Mode
*1)
Level Mode
*2)
Level Mode
*2)
Level Mode
*2)
Level Mode
*2)
Description
Interrupt Cycle and Falling Timing
OFF(H)
Fixed at “L”
2Hz(Duty50%)
(Default)
1Hz(Duty50%)
Once per 1 second (Synchronized with
second counter increment)
Once per 1 minute (at 00 seconds of
every minute)
Once per hour (at 00 minutes and 00
seconds of every hour)
Once per month (at 00 hours, 00 minutes,
and 00 seconds of first day of every
month)
* 1) Pulse Mode: 2-Hz and 1-Hz clock pulses are output in synchronization with the increment of the
second counter as illustrated in the timing chart below.
CTFG Bit
INTR Pin
Approx. 92µs
(Increment of second counter)
Rewriting of the second counter
In the pulse mode, the increment of the second counter is delayed by approximately 92 µs from the falling
edge of clock pulses. Consequently, time readings immediately after the falling edge of clock pulses may
appear to lag behind the time counts of the real-time clocks by approximately 1 second. Rewriting the
second counter will reset the other time counters of less than 1 second, driving the INTR pin low.
* 2) Level Mode: Periodic interrupt signals are output with selectable interrupt cycle settings of 1 second,
1 minute, 1 hour, and 1 month. The increment of the second counter is synchronized with the falling
edge of periodic interrupt signals. For example, periodic interrupt signals with an interrupt cycle setting
of 1 second are output in synchronization with the increment of the second counter as illustrated in the
timing chart below.
13
R2033K/T
CTFG Bit
INTR Pin
Setting CTFG bit to 0
(Increment of
second counter)
(Increment of
second counter)
Setting CTFG bit to 0
(Increment of
second counter)
*1), *2) When the oscillation adjustment circuit is used, the interrupt cycle will fluctuate once per 20sec. or
60sec. as follows:
Pulse Mode: The “L” period of output pulses will increment or decrement by a maximum of ±3.784 ms. For
example, 1-Hz clock pulses will have a duty cycle of 50 ±0.3784%.
Level Mode: A periodic interrupt cycle of 1 second will increment or decrement by a maximum of
±3.784 ms.
14
R2033K/T
•
Control Register 2 (Address Fh)
D7
D6
D5
D4
D3
D2
D1
D0
PON
CTFG
WAFG
DAFG
(For Writing)
VDSL
VDET
CLEN1
XST
PON
VDSL
VDET
CTFG
WAFG
DAFG
(For
Reading)
CLEN1
XST
Indefinite
0
0
1
0
0
0
0
Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
(1) VDSL
VDD Supply Voltage Monitoring Threshold Selection Bit
VDSL
Description
Selecting the VDD supply voltage monitoring threshold setting of 2.1v.
Selecting the VDD supply voltage monitoring threshold setting of
1.35v.
The VDSL bit is intended to select the VDD supply voltage monitoring threshold settings.
0
1
(2) VDET
(Default)
Supply Voltage Monitoring Result Indication Bit
VDET
Description
Indicating supply voltage above the supply voltage monitoring
(Default)
threshold settings.
1
Indicating supply voltage below the supply voltage monitoring
threshold settings.
Once the VDET bit is set to 1, the supply voltage monitoring circuit will be disabled while the VDET bit will
hold the setting of 1. The VDET bit accepts only the writing of 0, which restarts the supply voltage
monitoring circuit. Conversely, setting the VDET bit to 1 causes no event.
0
(3) XST
Oscillation Halt Sensing Monitor Bit
Description
XST
0
Sensing a halt of oscillation
1
Sensing a normal condition of oscillation
The XST accepts the reading and writing of 0 and 1. The XST bit will be set to 0 when the oscillation
halt sensing. The XST bit will hold 0 even after the restart of oscillation.
(4) PON
Power-on-reset Flag Bit
PON
Description
0
Normal condition
1
Detecting VDD power-on -reset
The PON bit is for sensing power-on reset condition.
(Default)
* The PON bit will be set to 1 when VDD power-on from 0 volts. The PON bit will hold the setting of 1 even
after power-on.
* When the PON bit is set to 1, all bits will be reset to 0, in the Oscillation Adjustment Register, Control
Register 1, and Control Register 2, except XST and PON. As a result, INTR pin stops outputting.
* The PON bit accepts only the writing of 0. Conversely, setting the PON bit to 1 causes no event.
15
R2033K/T
(5) CLEN1
32kHz Clock Output Bit 1
Description
CLEN1
0
Enabling the 32-kHz clock circuit
(Default)
1
Disabling the 32-kHz clock circuit
Setting the CLEN1 bit or the CLEN2 bit (D4 in the control register 1) to 0, and the CLKC pin to high
specifies generating clock pulses with the oscillation frequency of the 32.768-kHz crystal oscillator for
output from the 32KOUT pin. Conversely, setting both the CLEN1 and CLEN2 bit to 1 or CLKC pin to
low specifies disabling (”L”) such output.
(6) CTFG
Periodic Interrupt Flag Bit
CTFG
Description
0
Periodic interrupt output = “H”
(Default)
1
Periodic interrupt output = “L”
The CTFG bit is set to 1 when the periodic interrupt signals are output from the INTR pin (“L”). The
CTFG bit accepts only the writing of 0 in the level mode, which disables (“H”) the INTR pin until it is
enabled (“L”) again in the next interrupt cycle. Conversely, setting the CTFG bit to 1 causes no event.
(7) WAFG,DAFG
Alarm_W Flag Bit and Alarm_D Flag Bit
WAFG,DAFG
Description
0
Indicating a mismatch between current time and preset alarm time
(Default)
1
Indicating a match between current time and preset alarm time
The WAFG and DAFG bits are valid only when the WALE and DALE have the setting of 1, which is caused
approximately 61µs after any match between current time and preset alarm time specified by the Alarm_W
registers and the Alarm_D registers. The WAFG (DAFG) bit accepts only the writing of 0. INTR pin
outputs off (“H”) when this bit is set to 0. And INTR pin outputs “L” again at the next preset alarm time.
Conversely, setting the WAFG and DAFG bits to 1 causes no event. The WAFG and DAFG bits will have
the reading of 0 when the alarm interrupt circuit is disabled with the WALE and DALE bits set to 0. The
settings of the WAFG and DAFG bits are synchronized with the output of the INTR pin as shown in the
timing chart below.
Approx. 61µs
Approx. 61µs
WAFG(DAFG) Bit
INTR Pin
Writing of 0 to
WAFG(DAFG) bit
(Match between
(Match between
(Match between
current time and
current time and
current time and
preset alarm time)
16
Writing of 0 to
WAFG(DAFG) bit
preset alarm time)
preset alarm time)
R2033K/T
•
Time Counter (Address 0-2h)
Second Counter (Address 0h)
D7
D6
D5
S40
S20
0
S40
S20
0
Indefi
Indefi
nite
nite
D4
S10
S10
Indefi
nite
D3
S8
S8
Indefi
nite
D2
S4
S4
Indefi
nite
D1
S2
S2
Indefi
nite
D0
S1
S1
Indefi
nite
(For Writing)
(For Reading)
Default Settings *)
Minute Counter (Address 1h)
D7
D6
D5
M40
M20
0
M40
M20
0
Indefi
Indefi
nite
nite
D4
M10
M10
Indefi
nite
D3
M8
M8
Indefi
nite
D2
M4
M4
Indefi
nite
D1
M2
M2
Indefi
nite
D0
M1
M1
Indefi
nite
(For Writing)
(For Reading)
Default Settings *)
Hour Counter (Address 2h)
D7
D6
D5
D4
D3
D2
D1
D0
H10
H8
H4
H2
H1
(For Writing)
P/ A
or H20
H10
H8
H4
H2
H1
(For Reading)
0
0
P/ A
or H20
0
0
Indefi
Indefi
Indefi
Indefi
Indefi
Indefi
Default Settings *)
nite
nite
nite
nite
nite
nite
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
* Time digit display (BCD format) as follows:
The second digits range from 00 to 59 and are carried to the minute digit in transition from 59 to 00.
The minute digits range from 00 to 59 and are carried to the hour digits in transition from 59 to 00.
The hour digits range as shown in "P12 • Control Register 1 (ADDRESS Eh) (2) 12 /24: 12 /24-hour
Mode Selection Bit" and are carried to the day-of-month and day-of-week digits in transition from PM11 to
AM12 or from 23 to 00.
* Any writing to the second counter resets divider units of less than 1 second.
* Any carry from lower digits with the writing of non-existent time may cause the time counters to
malfunction. Therefore, such incorrect writing should be replaced with the writing of existent time data.
17
R2033K/T
•
Day-of-week Counter (Address 3h)
D7
D2
D1
D0
W4
W2
W1
(For Writing)
W4
W2
W1
(For Reading)
Indefi
Indefi
Indefi
Default Settings *)
nite
nite
nite
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
0
0
D6
0
0
D5
0
0
D4
0
0
D3
0
0
* The day-of-week counter is incremented by 1 when the day-of-week digits are carried to the day-of-month
digits.
* Day-of-week display (incremented in septimal notation):
(W4, W2, W1) = (0, 0, 0) → (0, 0, 1)→…→(1, 1, 0) → (0, 0, 0)
* Correspondences between days of the week and the day-of-week digits are user-definable
(e.g. Sunday = 0, 0, 0)
* The writing of (1, 1, 1) to (W4, W2, W1) is prohibited except when days of the week are unused.
•
Calendar Counter (Address 4-6h)
Day-of-month Counter (Address 4h)
D7
D6
D5
D20
0
0
D20
0
0
Indefi
nite
D4
D10
D10
Indefi
nite
D3
D8
D8
Indefi
nite
D2
D4
D4
Indefi
nite
D1
D2
D2
Indefi
nite
D0
D1
D1
Indefi
nite
(For Writing)
(For Reading)
Default Settings *)
Month Counter + Century Bit (Address 5h)
D7
D6
D5
D4
MO10
19 /20
0
0
MO10
19 /20
Indefin
0
0
Indefi
ite
nite
D3
MO8
MO8
Indefi
nite
D2
MO4
MO4
Indefi
nite
D1
MO2
MO2
Indefi
nite
D0
MO1
MO1
Indefi
nite
(For Writing)
(For Reading)
Default Settings *)
Year Counter (Address 6h)
D7
D6
D5
D4
D3
D2
D1
D0
Y80
Y40
Y20
Y10
Y8
Y4
Y2
Y1
(For Writing)
Y80
Y40
Y20
Y10
Y8
Y4
Y2
Y1
(For Reading)
Indefi
Indefi
Indefi
Indefi
Indefi
Indefi
Indefi
Indefi
Default Settings *)
nite
nite
nite
nite
nite
nite
nite
nite
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
* The calendar counters are configured to display the calendar digits in BCD format by using the automatic
calendar function as follows:
The day-of-month digits (D20 to D1) range from 1 to 31 for January, March, May, July, August, October,
and December; from 1 to 30 for April, June, September, and November; from 1 to 29 for February in leap
years; from 1 to 28 for February in ordinary years. The day-of-month digits are carried to the month
18
R2033K/T
digits in reversion from the last day of the month to 1. The month digits (MO10 to MO1) range from 1 to
12 and are carried to the year digits in reversion from 12 to 1.
The year digits (Y80 to Y1) range from 00 to 99 (00, 04, 08, …, 92, and 96 in leap years) and are carried to
the 19 /20 digits in reversion from 99 to 00.
The 19 /20 digits cycle between 0 and 1 in reversion from 99 to 00 in the year digits.
* Any carry from lower digits with the writing of non-existent calendar data may cause the calendar
counters to malfunction. Therefore, such incorrect writing should be replaced with the writing of existent
calendar data.
•
Oscillation Adjustment Register (Address 7h)
D7
D6
D5
D4
D3
D2
D1
D0
DEV
F6
F5
F4
F3
F2
F1
F0
(For Writing)
DEV
F6
F5
F4
F3
F2
F1
F0
(For Reading)
0
0
0
0
0
0
0
0
Default Settings *)
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
DEV bit
When DEV is set to 0, the Oscillation Adjustment Circuit operates 00, 20, 40 seconds.
When DEV is set to 1, the Oscillation Adjustment Circuit operates 00 seconds.
F6 to F0 bits
The Oscillation Adjustment Circuit is configured to change time counts of 1 second on the basis of
the settings of the Oscillation Adjustment Register at the timing set by DEV.
*
The Oscillation Adjustment Circuit will not operate with the same timing (00, 20, or 40 seconds)
as the timing of writing to the Oscillation Adjustment Register.
*
The F6 bit setting of 0 causes an increment of time counts by ((F5, F4, F3, F2, F1, F0) - 1) x 2.
The F6 bit setting of 1 causes a decrement of time counts by (( F5,F4,F3,F2,F1,F0 ) + 1) x 2.
The settings of "*, 0, 0, 0, 0, 0, *" ("*" representing either "0" or "1") in the F6, F5, F4, F3, F2, F1, and
F0 bits cause neither an increment nor decrement of time counts.
Example:
If (DEV, F6, F5, F4, F3, F2, F1, F0) is set to (0, 0, 0, 0, 0, 1, 1, 1), when the second digits read 00, 20, or
40, an increment of the current time counts of 32768 + (7 - 1) x 2 to 32780 (a current time count loss).
If (DEV, F6, F5, F4, F3, F2, F1, F0) is set to (0, 0, 0, 0, 0, 0, 0, 1), when the second digits read 00, 20, 40,
neither an increment nor a decrement of the current time counts of 32768.
If (DEV, F6, F5, F4, F3, F2, F1, F0) is set to (1, 1, 1, 1, 1, 1, 1, 0), when the second digits read 00, a
decrement of the current time counts of 32768 + (- 2) x 2 to 32764 (a current time count gain).
An increase of two clock pulses once per 20 seconds causes a time count loss of approximately 3 ppm (2 /
(32768 x 20 = 3.051 ppm). Conversely, a decrease of two clock pulses once per 20 seconds causes a
time count gain of 3 ppm. Consequently, when DEV is set to “0”, deviations in time counts can be
corrected with a precision of ±1.5 ppm. In the same way, when DEV is set to “1”, deviations in time
counts can be corrected with a precision of ±0.5 ppm. Note that the oscillation adjustment circuit is
configured to correct deviations in time counts and not the oscillation frequency of the 32.768-kHz clock
pulses. For further details, see "P32 Configuration of Oscillation Circuit and Correction of Time
Count Deviations • Oscillation Adjustment Circuit".
19
R2033K/T
•
Alarm_W Registers (Address 8-Ah)
Alarm_W Minute Register (Address 8h)
D7
D6
D5
D4
WM40
WM20
WM10
0
WM40
WM20
WM10
0
Indefi
Indefi
Indefi
nite
nite
nite
Alarm_W Hour Register (Address 9h)
D7
D6
D5
D4
WH10
WH20
WP/ A
0
0
WH20
WH10
WP/ A
0
0
Indefi
Indefi
nite
nite
D3
WM8
WM8
Indefi
nite
D2
WM4
WM4
Indefi
nite
D1
WM2
WM2
Indefi
nite
D0
WM1
WM1
Indefi
nite
D3
WH8
D2
WH4
D1
WH2
D0
WH1
(For Writing)
WH8
WH4
WH2
WH1
(For Reading)
Indefi
nite
Indefi
nite
Indefi
nite
Indefi
nite
Default Settings *)
(For Writing)
(For Reading)
Default Settings *)
Alarm_W Day-of-week Register (Address Ah)
D7
D6
D5
D4
D3
D2
D1
D0
WW6
WW5
WW4
WW3
WW2
WW1
WW0
(For Writing)
0
WW6
WW5
WW4
WW3
WW2
WW1
WW0
(For Reading)
0
Indefi
Indefi
Indefi
Indefi
Indefi
Indefi
Indefi
Default Settings *)
nite
nite
nite
nite
nite
nite
nite
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
* The D5 bit of the Alarm_W Hour Register represents WP/ A when the 12-hour mode is selected (0 for
a.m. and 1 for p.m.) and WH20 when the 24-hour mode is selected (tens in the hour digits).
* The Alarm_W Registers should not have any non-existent alarm time settings.
(Note that any mismatch between current time and preset alarm time specified by the Alarm_W registers
may disable the alarm interrupt circuit.)
* When the 12-hour mode is selected, the hour digits read 12 and 32 for 0 a.m. and 0 p.m., respectively.
(See "P12 •Control Register 1 (ADDRESS Eh) (2) 12 /24: 12 /24-hour Mode Selection Bit")
* WW0 to WW6 correspond to W4, W2, and W1 of the day-of-week counter with settings ranging from (0, 0,
0) to (1, 1, 0).
* WW0 to WW6 with respective settings of 0 disable the outputs of the Alarm_W Registers.
20
R2033K/T
Example of Alarm Time Setting
Alarm
Preset alarm time
00:00 a.m. on all days
01:30 a.m. on all days
11:59 a.m. on all days
00:00 p.m. on Mon. to
Fri.
01:30 p.m. on Sun.
11:59 p.m.
on Mon. ,Wed., and Fri.
Sun.
Day-of-week
Mon.
Tue.
Wed.
Th.
12-hour mode
Fri.
Sat.
10
hr.
WW0 WW1 WW2 WW3 WW4 WW5 WW6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
1
1
1
1
1
0
1
0
0
1
0
0
0
1
0
0
0
1
0
0
24-hour mode
1 10
1
10 1
hr. min. min. hr. hr.
10
1
min. min.
1
0
1
3
2
1
1
2
0
3
5
0
0
0
9
0
0
0
1
1
0
1
1
2
0
3
5
0
0
0
9
0
2
3
1
1
3
5
0
9
1
2
3
3
3
5
0
9
Note that the correspondence between WW0 to WW6 and the days of the week shown in the above table is
only an example and not mandatory.
•
Alarm_D Register (Address B-Ch)
Alarm_D Minute Register (Address Bh)
D7
D6
D5
D4
DM40
DM20
DM10
0
DM40
DM20
DM10
0
Indefi
Indefi
Indefi
nite
nite
nite
D3
DM8
DM8
Indefi
nite
D2
DM4
DM4
Indefi
nite
D1
DM2
DM2
Indefi
nite
D0
DM1
DM1
Indefi
nite
(For Writing)
(For Reading)
Default Settings *)
Alarm_D Hour Register (Address Ch)
D7
D6
D5
D4
D3
D2
D1
D0
DH20
DH10
DH8
DH4
DH2
DH1
(For Writing)
DP/ A
0
0
DH20
DH10
DH8
DH4
DH2
DH1
(For Reading)
DP/ A
0
0
Indefi
Indefi
Indefi
Indefi
Indefi
Indefi
Default Settings *)
nite
nite
nite
nite
nite
nite
*) Default settings: Default value means read / written values when the PON bit is set to “1” due to VDD
power-on from 0 volts.
* The D5 bit represents DP/ A when the 12-hour mode is selected (0 for a.m. and 1 for p.m.) and DH20
when the 24-hour mode is selected (tens in the hour digits).
* The Alarm_D registers should not have any non-existent alarm time settings.
(Note that any mismatch between current time and preset alarm time specified by the Alarm_D registers
may disable the alarm interrupt circuit.)
* When the 12-hour mode is selected, the hour digits read 12 and 32 for 0a.m. and 0p.m., respectively.
(See "P12 •Control Register 1 (ADDRESS Eh) (2) 12 /24: 12 /24-hour Mode Selection Bit")
21
R2033K/T
Interfacing with the CPU
•
DATA TRANSFER FORMATS
(1) Timing Between CE Pin Transition and Data Input / Output
The R2033K/T adopts a 3-wire serial interface by which they use the CE (Chip Enable), SCLK (Serial Clock),
and SIO (Serial Input/Output) pins to receive and send data to and from the CPU. The 3-wire serial interface
provides two types of input/output timings with which the SIO pin output and input are synchronized with the
rising or falling edges of the SCLK pin input, respectively, and vice versa. The R2033K/T is configured to select
either one of two different input/output timings depending on the level of the SCLK pin in the low to high
transition of the CE pin. Namely, when the SCLK pin is held low in the low to high transition of the CE pin, the
models will select the timing with which the SIO pin output is synchronized with the rising edge of the SCLK pin
input, and the input is synchronized with the falling edge of the SCLK pin input, as illustrated in the timing chart
below.
CE
tCES
SCLK
tDS
tDH
tRD
SIO (for writing)
SIO (for reading)
Conversely, when the SCLK pin is held high in the low to high transition of the CE pin, the models will select the
timing with which the SIO pin output is synchronized with the falling edge of the SCLK pin input, and the input is
synchronized with the rising edge of the SCLK pin input, as illustrated in the timing chart below.
CE
tCES
SCLK
tDS
SIO (for writing)
SIO (for reading)
22
tDH
tRD
R2033K/T
(2) Data Transfer Formats
Data transfer is commenced in the low to high transition of the CE pin input and completed in its high to low
transition. Data transfer is conducted serially in multiple units of 1 byte (8 bits). The former 4 bits are used to
specify in the Address Pointer a head address with which data transfer is to be commenced from the host. The
latter 4 bits are used to select either reading data transfer or writing data transfer, and to set the Transfer Format
Register to specify an appropriate data transfer format. All data transfer formats are designed to transfer the
most significant bit (MSB) first.
CE
1
2
3
4
5
6
7
8
1
2
A3
A2
A1
A0
C3
C2
C1
C0
D7
D6
3
SCLK
SIO
Setting
the Address Pointer
Setting the Transfer
Format Register
D3
D2
D1
D0
Writing or Reading data transfer
Two types of data transfer formats are available for reading data transfer and writing data transfer each.
•
Writing Data Transfer Formats
(1) 1-byte Writing Data Transfer Format
The first type of writing data transfer format is designed to transfer 1-byte data at a time and can be selected by
specifying in the address pointer a head address with which writing data transfer is to be commenced and then
writing the setting of 8h to the transfer format register. This 1-byte writing data transfer can be completed by
driving the CE pin low or continued by specifying a new head address in the address pointer and setting the data
transfer format.
Example of 1-byte Writing Data Transfer (For Writing Data to Addresses Fh and 7h)
CE
SIO
1 1 1 1 1 0 0 0
Specifying FhSetting 8h in
in the
Address
Pointer
the Transfer
Data
Writing data to
address Fh
Format
0 1 1 1 1 0 0 0
Specifying 7h Setting 8h in Writing data to
in the
Address
Register
Data transfer from the host
Data
Pointer
the Transfer
address 7h
Format
Register
Data transfer from the RTCs
23
R2033K/T
(2) Burst Writing Data Transfer Format
The second type of writing data transfer format is designed to transfer a sequence of data serially and can be
selected by specifying in the address pointer a head address with which writing data transfer is to be
commenced and then writing the setting of 0h to the transfer format register. The address pointer is
incremented for each transfer of 1-byte data and cycled from Fh to 0h. This burst writing data transfer can be
completed by driving the CE pin low.
Example of Burst Writing Data Transfer (For Writing Data to Addresses Eh, Fh, and 0h)
CE
SIO
1 1 1 0 0 0 0 0
Data
Specifying EhSetting 0h in Writing data to
in the
Address
Pointer
the Transfer
Writing data to
address Fh
address Eh
Writing data to
address 0h
Format
Register
Data transfer from the host
•
Data
Data
Data transfer from the RTCs
Reading Data Transfer Formats
(1) 1-byte Reading Data Transfer Format
The first type of reading data transfer format is designed to transfer 1-byte data at a time and can be selected by
specifying in the Address Pointer a head address with which reading data transfer is to be commenced and then
the setting of writing Ch to the Transfer Format Register. This 1-byte reading data transfer can be completed
by driving the CE pin low or continued by specifying a new head address in the Address Pointer and selecting
this type of reading data Transfer Format.
Example of 1-byte Reading Data Transfer (For Reading Data from Addresses Eh and 2h)
CE
SIO
1 1 1 0 1 1 0 0
Data
Specifying EhSetting Ch in
Reading data from
in the
Address
Pointer
the Transfer
address Eh
Format
Register
Data
Specifying 2h Setting Ch in Reading data from
in the
Address
Data transfer from the host
24
0 0 1 0 1 1 0 0
Pointer
the Transfer
address 2h
Format
Register
Data transfer from the RTCs
R2033K/T
(2) Burst Reading Data Transfer Format
The second type of reading data transfer format is designed to transfer a sequence of data serially and can be
selected by specifying in the address pointer a head address with which reading data transfer is to be
commenced and then writing the setting of 4h to the transfer format register. The address pointer is
incremented for each transfer of 1-byte data and cycled from Fh to 0h. This burst reading data transfer can be
completed by driving the CE pin low.
Example of Burst Reading Data Transfer (For Reading Data from Addresses Fh, 0h, and 1h)
CE
SIO
1 1 1 1 0 1 0 0
DATA
Specifying FhSetting 4h in Reading data from
the Transfer
in the
address Fh
Address
Pointer
DATA
DATA
Reading data from
Reading data from
address 0h
address 1h
Format
Register
Data transfer from the host
Data transfer from the RTCs
(3) Combination of 1-byte Reading and writing Data Transfer Formats
The 1-byte reading and writing data transfer formats can be combined together and further followed by any other
data transfer format.
Example of Reading Modify Writing Data Transfer
(For Reading and Writing Data from and to Address Fh)
CE
SIO
1 1 1 1 1 1 0 0
DATA
Specifying FhSetting Ch in Reading data from
the Transfer
in the
address Fh
Format
Address
Pointer
DATA
1 1 1 1 1 0 0 0
Specifying FhSetting 8h in
in the
Address
Register
Pointer
Data transfer from the host
Writing data to
the Transfer
address Fh
Format
Register
Data transfer from the RTCs
The reading and writing data transfer formats correspond to the settings in the transfer format register as shown
in the table below.
Writing data
transfer
Reading data
transfer
1 Byte
8h
(1,0,0,0)
Ch
(1,1,0,0)
Burst
0h
(0,0,0,0)
4h
(0,1,0,0)
25
R2033K/T
•
Considerations in Reading and Writing Time Data under special condition
Any carry to the second digits in the process of reading or writing time data may cause reading or writing
erroneous time data. For example, suppose a carry out of 13:59:59 into 14:00:00 occurs in the process of
reading time data in the middle of shifting from the minute digits to the hour digits. At this moment, the second
digits, the minute digits, and the hour digits read 59 seconds, 59 minutes, and 14 hours, respectively (indicating
14:59:59) to cause the reading of time data deviating from actual time virtually 1 hour. A similar error also
occurs in writing time data. To prevent such errors in reading and writing time data, the R2033K/T has the
function of temporarily locking any carry to the second digits during the high interval of the CE pin and unlocking
such a carry in its high to low transition. Note that a carry to the second digits can be locked for only 1 second,
during which time the CE pin should be driven low.
Actual time
13:59:59
14:00:00
14:00:01
CE
Max.62µs
Time counts
within RTC
13:59:59
14:00:00
14:00:01
The effective use of this function requires the following considerations in reading and writing time data:
(1) Hold the CE pin high in each session of reading or writing time data.
(2) Ensure that the high interval of the CE pin lasts within 1 second. Should there be any possibility of the host
going down in the process of reading or writing time data, make arrangements in the peripheral circuitry as to
drive the CE pin low or open at the moment that the host actually goes down.
(3) Leave a time span of 31µs or more from the low to high transition of the CE pin to the start of access to
addresses 0h to 6h in order that any ongoing carry of the time digits may be completed within this time span.
(4) Leave a time span of 62µs or more from the high to low transition of the CE pin to its low to high transition in
order that any ongoing carry of the time digits during the high interval of the CE pin may be adjusted within this
time span.
The considerations listed in (1), (3), and (4) above are not required when the process of reading or writing time
data is obviously free from any carry of the time digits.
(e.g. reading or writing time data in synchronization with the periodic interrupt function in the level mode or the
alarm interrupt function).
Good and bad examples of reading and writing time data are illustrated on the next page.
26
R2033K/T
Good Example
Any address other than addresses 0h to 6h
permits of immediate reading or writing without
requiring a time span of 31 µs.
Time span of 31µs or more
CE
SIO
F4h
Address Pointer
= Fh
Transfer Format
Register = 4h
DATA
DATA
Reading from
Address Fh
(control2)
Reading from
Address 0h
(sec.)
DATA
DATA
Reading from
Address 1h
(min.)
Reading from
Address 2h
(hr.)
Bad Example (1)
(Where the CE pin is once driven low in the process of reading time data)
31µs or more
31µs or more
CE
SIO
0Ch
Address Pointer
= 0h
Transfer Format
Register = Ch
Data
14h
Address Pointer
= 1h
Transfer Format
Register = 4h
Reading from
Address 0h
(sec.)
Data
Data
Reading from
Address 1h
(min.)
Reading from
Address 2h
(hr.)
Bad Example (2)
(Where a time span of less than 31µs is left until the start of the process of writing time data)
Time span of less than 31µs
CE
F0h
SIO
Address Pointer
= Fh
Transfer Format
Register = 0h
Data
Writing to
Address Fh
(contorl2)
Data
Writing to
Address 0h
(sec.)
Data
Writing to
Address 1h
(min.)
Data
Writing to
Address 2h
(hr.)
Bad Example (3)
(Where a time span of less than 62µs is left between the adjacent processes of reading time data)
Less than 62µs
CE
0Ch
SIO
Address Pointer
= 0h
Transfer Format
Register = Ch
0Ch
0Ch
Data
Reading from
Address 0h
(sec.)
Data transfer from the host
Address Pointer
= 0h
Transfer Format
Register = Ch
Data
Data
Reading from
Address 0h
(sec.)
Data transfer from RTCs
27
R2033K/T
Configuration of Oscillation Circuit and Correction of Time Count
Deviations
•
Configuration of Oscillation Circuit
OSCIN
Oscillator CG
Circuit
32kHz
OSCOUT
Typical externally-equipped element
X’tal : 32.768kHz
(R1=30kΩ typ)
(CL=6pF to 8pF)
Standard values of internal elements
CG,CD 10pF typ
CD
A
The oscillation circuit is driven at a constant voltage of approximately 1.2 volts relative to the level of the VSS pin
input. As such, it is configured to generate an oscillating waveform with a peak-to-peak voltage on the order of
1.2 volts on the positive side of the VSS pin input.
< Considerations in Handling quartz crystal unit >
Generally, quartz crystal units have basic characteristics including an equivalent series resistance (R1)
indicating the ease of their oscillation and a load capacitance (CL) indicating the degree of their center frequency.
Particularly, quartz crystal units intended for use in the R2033K/T are recommended to have a typical R1 value
of 50kΩ and a typical CL value of 6 to 9pF. To confirm these recommended values, contact the manufacturers
of quartz crystal units intended for use in these particular models.
< Considerations in Installing Components around the Oscillation Circuit >
1) Install the quartz crystal unit in the closest possible vicinity to the real-time clock ICs.
2) Avoid laying any signal lines or power lines in the vicinity of the oscillation circuit (particularly in the area
marked "A" in the above figure).
3) Apply the highest possible insulation resistance between the OSCIN and OSCOUT pins and the printed
circuit board.
4) Avoid using any long parallel lines to wire the OSCIN and OSCOUT pins.
5) Take extreme care not to cause condensation, which leads to various problems such as oscillation halt.
< Other Relevant Considerations >
1) We cannot recommend connecting the external input of 32.768-kHz clock pulses to the OSCIN pin.
2) To maintain stable characteristics of the quartz crystal unit, avoid driving any other IC through 32.768-kHz
clock pulses output from the OSCOUT pin.
28
R2033K/T
•
Measurement of Oscillation Frequency
VDD
CLKC
OSCIN
OSCOUT
32768Hz
Frequency
Counter
32KOUT
VSS
* 1) The R2033K/T is configured to generate 32.768-kHz clock pulses for output from the 32KOUT pin.
* 2) A frequency counter with 6 (more preferably 7) or more digits on the order of 1ppm is recommended for
use in the measurement of the oscillation frequency of the oscillation circuit.
•
Adjustment of Oscillation frequency
The oscillation frequency of the oscillation circuit can be adjusted by varying procedures depending on the
usage of Model R2033K/T in the system into which they are to be built and on the allowable degree of time count
errors. The flow chart below serves as a guide to selecting an optimum oscillation frequency adjustment
procedure for the relevant system.
Start
Use 32-kHz
clock output?
YES
NO Allowable time count precision on order of oscillation
frequency variations of crystal oscillator (*1) plus NO
frequency variations of RTC (*2)? (*3)
YES
YES
Course (A)
Course (B)
Use 32-kHz clock output without regard
to its frequency precision
Course (C)
NO
YES
Allowable time count precision on order of oscillation
frequency variations of crystal oscillator (*1) plus NO
frequency variations of RTC (*2)? (*3)
Course (D)
* 1) Generally, quartz crystal units for commercial use are classified in terms of their center frequency
depending on their load capacitance (CL) and further divided into ranks on the order of ±10, ±20, and ±50ppm
depending on the degree of their oscillation frequency variations.
* 2) Basically, Model R2033K/T is configured to cause frequency variations on the order of ±5 to ±10ppm at
25°C.
* 3) Time count precision as referred to in the above flow chart is applicable to normal temperature and actually
affected by the temperature characteristics and other properties of quartz crystal units.
29
R2033K/T
Course (A)
When the time count precision of each RTC is not to be adjusted, the quartz crystal unit intended for use in that
RTC may have any CL value requiring no presetting. The quartz crystal unit may be subject to frequency
variations which are selectable within the allowable range of time count precision. Several quartz crystal units
and RTCs should be used to find the center frequency of the quartz crystal units by the method described in
"P29 • Measurement of Oscillation Frequency" and then calculate an appropriate oscillation adjustment value
by the method described in "P32 • Oscillation Adjustment Circuit" for writing this value to the R2033K/T.
Course (B)
When the time count precision of each RTC is to be adjusted within the oscillation frequency variations of the
quartz crystal unit plus the frequency variations of the real-time clock ICs, it becomes necessary to correct
deviations in the time count of each RTC by the method described in " P29 • Oscillation Adjustment Circuit".
Such oscillation adjustment provides quartz crystal units with a wider range of allowable settings of their
oscillation frequency variations and their CL values. The real-time clock IC and the quartz crystal unit intended
for use in that real-time clock IC should be used to find the center frequency of the quartz crystal unit by the
method described in " P29 • Measurement of Oscillation Frequency" and then confirm the center frequency
thus found to fall within the range adjustable by the oscillation adjustment circuit before adjusting the oscillation
frequency of the oscillation circuit. At normal temperature, the oscillation frequency of the oscillator circuit can
be adjusted by up to approximately ±0.5ppm.
Course (C)
Course (C) together with Course (D) requires adjusting the time count precision of each RTC as well as the
frequency of 32.768-kHz clock pulses output from the 32KOUT pin. Normally, the oscillation frequency of the
crystal oscillator intended for use in the RTCs should be adjusted by adjusting the oscillation stabilizing
capacitors CG and CD connected to both ends of the crystal oscillator. The R2033K/T, which incorporate the
CG and the CD, require adjusting the oscillation frequency of the crystal oscillator through its CL value.
Generally, the relationship between the CL value and the CG and CD values can be represented by the following
equation:
CL = (CG × CD)/(CG + CD) + CS where "CS" represents the floating capacity of the printed circuit board.
The crystal oscillator intended for use in the R2033K/T is recommended to have the CL value on the order of 6 to
9pF. Its oscillation frequency should be measured by the method described in " P.29 • Measurement of
Oscillation Frequency ". Any crystal oscillator found to have an excessively high or low oscillation frequency
(causing a time count gain or loss, respectively) should be replaced with another one having a smaller and
greater CL value, respectively until another one having an optimum CL value is selected. In this case, the bit
settings disabling the oscillation adjustment circuit (see " P.32 • Oscillation Adjustment Circuit") should be
written to the oscillation adjustment register.
Incidentally, the high oscillation frequency of the crystal oscillator can also be adjusted by adding an external
oscillation stabilization capacitor CGOUT or/and CDOUT as illustrated in the diagram below.
30
R2033K/T
*1) The CGOUT or/and CDOUT should have a
capacitance ranging from 0 to 6 pF.
OSCIN
Oscillator
Circuit
CG
RD
32kHz
OSCOUT
CD
CGOUT
CDOUT
However, if adding CGOUT and/or CDOUT, Time keeping Voltage and Current will be worse, and it will be hard
to oscillate. For reference, the data of Time keeping voltage and current when adding CGOUT=CDOUT=5pF
are shown in the table below.
(Topt=-40 to 85°C, VSS=0v)
PIN
Item
Condition
Min.
TYP.
MAX.
UNITS
Vclk
Time Keeping
CGout=CDout=5pF
1.15
5.5
V
Voltage
IDD
Time Keeping
VDD=3V,
Current
0.55
1.20
µA
CE, SCLK, SIO, CLKC, INTR =0v
32KOUT=OFF
CGout=CDout=0pF
Course (D)
It is necessary to select the crystal oscillator in the same manner as in Course (C) as well as correct errors in the
time count of each RTC in the same manner as in Course (B) by the method described in " P.32 • Oscillation
Adjustment Circuit ".
31
R2033K/T
•
Oscillation Adjustment Circuit
The oscillation adjustment circuit can be used to correct a time count gain or loss with high precision by varying
the number of 1-second clock pulses once per 20 seconds or 60 seconds. When DEV bit in the Oscillation
Adjustment Register is set to 0, R2033K/T varies number of 1-second clock pulses once per 20 seconds.
When DEV bit is set to 1, R2033K/T varies number of 1-second clock pulses once per 60 seconds. The
oscillation adjustment circuit can be disabled by writing the settings of "*, 0, 0, 0, 0, 0, *" ("*" representing "0" or
"1") to the F6, F5, F4, F3, F2, F1, and F0 bits in the oscillation adjustment circuit. Conversely, when such
oscillation adjustment is to be made, an appropriate oscillation adjustment value can be calculated by the
equation below for writing to the oscillation adjustment circuit.
(1) When Oscillation Frequency (* 1) Is Higher Than Target Frequency (* 2) (Causing Time Count Gain)
When DEV=0:
Oscillation adjustment value (*3) = (Oscillation frequency - Target Frequency + 0.1)
Oscillation frequency × 3.051 × 10-6
≈ (Oscillation Frequency – Target Frequency) × 10 + 1
When DEV=1:
Oscillation adjustment value (*3) = (Oscillation frequency - Target Frequency + 0.0333)
Oscillation frequency × 1.017 × 10-6
≈ (Oscillation Frequency – Target Frequency) × 30 + 1
* 1) Oscillation frequency:
The clock frequency output from the 32KOUT pin at normal temperature in the manner described in "
P29 • Measurement of Oscillation Frequency".
* 2) Target frequency:
Desired frequency to be set. Generally, a 32.768-kHz quartz crystal unit has such temperature
characteristics as to have the highest oscillation frequency at normal temperature. Consequently,
the quartz crystal unit is recommended to have target frequency settings on the order of 32.768 to
32.76810 kHz (+3.05ppm relative to 32.768 kHz). Note that the target frequency differs depending
on the environment or location where the equipment incorporating the RTC is expected to be
operated.
* 3) Oscillation adjustment value:
Value that is to be finally written to the F0 to F6 bits in the Oscillation Adjustment Register and is
represented in 7-bit coded decimal notation.
(2) When Oscillation Frequency Is Equal To Target Frequency (Causing Time Count neither Gain nor Loss)
Oscillation adjustment value = 0, +1, -64, or –63
32
R2033K/T
(3) When Oscillation Frequency Is Lower Than Target Frequency (Causing Time Count Loss)
When DEV=0:
Oscillation adjustment value = (Oscillation frequency - Target Frequency)
Oscillation frequency × 3.051 × 10-6
≈ (Oscillation Frequency – Target Frequency) × 10
When DEV=1:
Oscillation adjustment value = (Oscillation frequency - Target Frequency)
Oscillation frequency × 1.017 × 10-6
≈ (Oscillation Frequency – Target Frequency) × 30
Oscillation adjustment value calculations are exemplified below
(A) For an oscillation frequency = 32768.85Hz and a target frequency = 32768.05Hz
When setting DEV bit to 0:
Oscillation adjustment value = (32768.85 - 32768.05 + 0.1) / (32768.85 × 3.051 × 10-6)
≈ (32768.85 - 32768.05) × 10 + 1
= 9.001 ≈ 9
In this instance, write the settings (DEV,F6,F5,F4,F3,F2,F1,F0)=(0,0,0,0,1,0,0,1) in the oscillation adjustment
register. Thus, an appropriate oscillation adjustment value in the presence of any time count gain represents a
distance from 01h.
When setting DEV bit to 1:
Oscillation adjustment value = (32768.85 - 32768.05 + 0.0333) / (32768.85 × 1.017 × 10-6)
≈ (32768.85 - 32768.05) × 30 + 1
= 25.00 ≈ 25
In this instance, write the settings (DEV,F6,F5,F4,F3,F2,F1,F0)=(1,0,0,1,1,0,0,1) in the oscillation adjustment
register.
(B) For an oscillation frequency = 32762.22Hz and a target frequency = 32768.05Hz
When setting DEV bit to 0:
Oscillation adjustment value = (32762.22 - 32768.05) / (32762.22 × 3.051 × 10-6)
≈ (32762.22 - 32768.05) × 10
= -58.325 ≈ -58
To represent an oscillation adjustment value of - 58 in 7-bit coded decimal notation, subtract 58 (3Ah) from 128
(80h) to obtain 46h. In this instance, write the settings of (DEV,F6,F5,F4,F3,F2,F1,F0) = (0,1,0,0,0,1,1,0) in the
oscillation adjustment register. Thus, an appropriate oscillation adjustment value in the presence of any time
count loss represents a distance from 80h.
When setting DEV bit to 1:
Oscillation adjustment value = (32762.22 - 32768.05) / (32762.22 × 1.017 × 10-6)
≈ (32762.22 - 32768.05) × 30
= -174.97 ≈ -175
Oscillation adjustment value can be set from -62 to 63. Then, in this case, Oscillation adjustment value is out of
range.
33
R2033K/T
(4) Difference between DEV=0 and DEV=1
Difference between DEV=0 and DEV=1 is following,
Maximum value range
Minimum resolution
DEV=0
-189.2ppm to 189.2ppm
3ppm
DEV=1
-62ppm to 63ppm
1ppm
Notes:
If following 3 conditions are completed, actual clock adjustment value could be different from target
adjustment value that set by oscillator adjustment function.
1. Using oscillator adjustment function
2. Access to R2033K/T at random, or synchronized with external clock that has no relation to R2033K/T, or
synchronized with periodic interrupt in pulse mode.
3. Access to R2033K/T more than 2 times per each second on average.
For more details, please contact to Ricoh.
•
How to evaluate the clock gain or loss
The oscillator adjustment circuit is configured to change time counts of 1 second on the basis of the settings of
the oscillation adjustment register once in 20 seconds or 60 seconds. The oscillation adjustment circuit does
not effect the frequency of 32768Hz-clock pulse output from the 32KOUT pin. Therefore, after writing the
oscillation adjustment register, we cannot measure the clock error with probing 32KOUT clock pulses. The way
to measure the clock error as follows:
(1) Output a 1Hz clock pulse of Pulse Mode with interrupt pin
Set (0,0,x,x,0,0,1,1) to Control Register 1 at address Eh.
(2) After setting the oscillation adjustment register, 1Hz clock period changes every 20seconds ( or every 60
seconds) like next page figure.
1Hz clock pulse
T0
T0
T0
19 times
T1
1 time
Measure the interval of T0 and T1 with frequency counter. A frequency counter with 7 or more digits is
recommended for the measurement.
(3) Calculate the typical period from T0 and T1
T = (19×T0+1×T1)/20
Calculate the time error from T.
34
R2033K/T
Power-on Reset, Oscillation Halt Sensing, and Supply Voltage
Monitoring
•
PON, XST , and VDET
The power-on reset circuit is configured to reset control register1, 2, and clock adjustment register when VDD
power up from 0v. The oscillation halt sensing circuit is configured to record a halt on oscillation by 32.768-kHz
clock pulses. The supply voltage monitoring circuit is configured to record a drop in supply voltage below a
threshold voltage of 1.6 or 1.3v.
Each function has a monitor bit. I.e. the PON bit is for the power-on reset circuit, and XST bit is for the
oscillation halt sensing circuit, and VDET is for the supply voltage monitoring circuit. PON and VDET bits are
activated to “H”. However, XST bit is activated to “L”. The PON and VDET accept only the writing of 0, but
XST accepts the writing of 0 and 1. The PON bit is set to 1, when VDD power-up from 0V, but VDET is set to
0, and XST is indefinite.
The functions of these three monitor bits are shown in the table below.
PON
Monitoring for the
power-on reset function
Function
Address
Activated
When VDD
power up from 0v
accept the writing
D4 in Address Fh
High
1
XST
Monitoring for the
oscillation halt sensing
function
D5 in Address Fh
Low
indefinite
VDET
a drop in supply voltage
below a threshold voltage
of 1.6 or 1.3v
D6 in Address Fh
High
0
0 only
Both 0 and 1
0 only
The relationship between the PON, XST , and VDET is shown in the table below.
PON
XST
VDET
0
0
0
0
0
1
0
1
0
0
1
1
1
*
*
Conditions of supply voltage and
oscillation
Halt on oscillation, but no drop in
VDD supply voltage below threshold
voltage
Halt on oscillation and drop in VDD
supply voltage below threshold
voltage, but no drop to 0V
No drop in VDD supply voltage
below threshold voltage and no halt
in oscillation
Drop in VDD supply voltage below
threshold voltage and no halt on
oscillation
Drop in supply voltage to 0v
Condition of oscillator, and
back-up status
Halt on oscillation cause of
condensation etc.
Halt on oscillation cause of drop in
back-up battery voltage
Normal condition
No halt on oscillation, but drop in
back-up battery voltage
Power-up from 0v,
35
R2033K/T
Threshold voltage (1.6v or 1.3v)
VDD
32768Hz Oscillation
Power-on reset flag
(PON)
Oscillation halt
sensing flag (XST)
Supply voltage
monitor flag (VDET)
Internal initialization
period (1 to 2 sec.)
VDET←0
XST←1
PON←0
VDET←0
XST←1
PON←1
Internal initialization
period (1 to 2 sec.)
VDET←0
XST←1
PON←0
When the PON bit is set to 1 in the control register 2, the DEV, F6 to F0, WALE, DALE, 12 /24, CLEN2 , TEST,
CT2, CT1, CT0, VDSL, VDET, CLEN1 , CTFG, WAFG, and DAFG bits are reset to 0 in the oscillation
adjustment register, the control register 1, and the control register 2. The PON bit is also set to 1 at power-on
from 0v.
< Considerations in Using Oscillation Halt Sensing Circuit >
Be sure to prevent the oscillation halt sensing circuit from malfunctioning by preventing the following:
1) Instantaneous power-down on the VDD
2) Condensation on the crystal oscillator
3) On-board noise to the crystal oscillator
4) Applying to individual pins voltage exceeding their respective maximum ratings
In particular, note that the XST bit may fail to be set to 0 in the presence of any applied supply voltage as
illustrated below in such events as backup battery installation. Further, give special considerations to prevent
excessive chattering in the oscillation halt sensing circuit.
VDD
36
R2033K/T
•
Voltage Monitoring Circuit
The supply monitoring circuit is configured to conduct a sampling operation during an interval of 7.8ms per
second to check for a drop in supply voltage below a threshold voltage of 1.6 or 1.3v for the VDSL bit setting of 0
(the default setting) or 1, respectively, in the Control Register 2, thus minimizing supply current requirements as
illustrated in the timing chart below. This circuit suspends a sampling operation once the VDET bit is set to 1 in
the Control Register 2. The supply voltage monitor is useful for back-up battery checking.
VDD
1.6v or 1.3v
PON
7.8ms
Internal
initialization
period
(1 to 2sec.)
1s
Sampling timing for
VDD supply voltage
VDET
(D6 in Address Fh)
PON←0
VDET←0
VDET←0
37
R2033K/T
Alarm and Periodic Interrupt
The R2033K/T incorporates the alarm interrupt circuit and the periodic interrupt circuit that are configured to
generate alarm signals and periodic interrupt signals for output from the INTR pin as described below.
(1) Alarm Interrupt Circuit
The alarm interrupt circuit is configured to generate alarm signals for output from the INTR , which is driven low
(enabled) upon the occurrence of a match between current time read by the time counters (the day-of-week,
hour, and minute counters) and alarm time preset by the alarm registers (the Alarm_W registers intended for the
day-of-week, hour, and minute digit settings and the Alarm_D registers intended for the hour and minute digit
settings).
(2) Periodic Interrupt Circuit
The periodic interrupt circuit is configured to generate either clock pulses in the pulse mode or interrupt signals in
the level mode for output from the INTR pin depending on the CT2, CT1, and CT0 bit settings in the control
register 1.
The above two types of interrupt signals are monitored by the flag bits (i.e. the WAFG, DAFG, and CTFG bits in
the Control Register 2) and enabled or disabled by the enable bits (i.e. the WALE, DALE, CT2, CT1, and CT0
bits in the Control Register 1) as listed in the table below.
Alarm_W
Alarm_D
Peridic interrupt
Flag bits
WAFG
(D1 at Address Fh)
DAFG
(D0 at Address Fh)
CTFG
(D2 at Address Fh)
Enable bits
WALE
(D7 at Address Eh)
DALE
(D6 at Address Eh)
CT2=CT1=CT0=0
(These bit setting of “0” disable the Periodic Interrupt)
(D2 to D0 at Address Eh)
* At power-on, when the WALE, DALE, CT2, CT1, and CT0 bits are set to 0 in the Control Register 1,
the INTR pin is driven high (disabled).
* When two types of interrupt signals are output simultaneously from the INTR pin, the output from the
INTR pin becomes an OR waveform of their negative logic.
Example: Combined Output to INTR Pin Under Control of
Alarm_D and Periodic Interrupt
Alarm_D
Periodic Interrupt
INTR
In this event, which type of interrupt signal is output from the INTR pin can be confirmed by reading the
DAFG, and CTFG bit settings in the Control Register 2.
38
R2033K/T
•
Alarm Interrupt
The alarm interrupt circuit is controlled by the enable bits (i.e. the WALE and DALE bits in the Control Register 1)
and the flag bits (i.e. the WAFG and DAFG bits in the Control Register 2). The enable bits can be used to
enable this circuit when set to 1 and to disable it when set to 0. When intended for reading, the flag bits can be
used to monitor alarm interrupt signals. When intended for writing, the flag bits will cause no event when set to
1 and will drive high (disable) the alarm interrupt circuit when set to 0.
The enable bits will not be affected even when the flag bits are set to 0. In this event, therefore, the alarm
interrupt circuit will continue to function until it is driven low (enabled) upon the next occurrence of a match
between current time and preset alarm time.
The alarm function can be set by presetting desired alarm time in the alarm registers (the Alarm_W Registers for
the day-of-week digit settings and both the Alarm_W Registers and the Alarm_D Registers for the hour and
minute digit settings) with the WALE and DALE bits once set to 0 and then to 1 in the Control Register 1. Note
that the WALE and DALE bits should be once set to 0 in order to disable the alarm interrupt circuit upon the
coincidental occurrence of a match between current time and preset alarm time in the process of setting the
alarm function.
Interval (1min.) during which a match
between current time and preset alarm time
occurs
INTR
WALE←1 current time =
WALE←0
preset alarm time (DALE)
(DALE)
WALE←1
(DALE)
current time =
preset alarm time
INTR
WALE←1 current time =
preset alarm time
(DALE)
WAFG←0
(DAFG)
current time =
preset alarm time
After setting WALE(DALE) to 0, Alarm registers is set to current time, and WALE(DALE) is set to 1, INTR will
be not driven to “L” immediately, INTR will be driven to “L” at next alarm setting time.
39
R2033K/T
•
Periodic Interrupt
Setting of the periodic selection bits (CT2 to CT0) enables periodic interrupt to the CPU. There are two waveform
modes: pulse mode and level mode. In the pulse mode, the output has a waveform duty cycle of around 50%.
In the level mode, the output is cyclically driven low and, when the CTFG bit is set to 0, the output is return to
High (OFF).
CT2
CT1
CT0
Description
Interrupt Cycle and Falling Timing
Wave form
mode
0
0
0
0
1
0
0
1
1
0
0
1
0
1
0
Pulse Mode *1)
Pulse Mode *1)
Level Mode *2)
1
0
1
Level Mode *2)
1
1
0
Level Mode *2)
1
1
1
Level Mode *2)
OFF(H)
Fixed at “L”
2Hz(Duty50%)
1Hz(Duty50%)
Once per 1 second (Synchronized with
Second counter increment)
Once per 1 minute (at 00 seconds of every
Minute)
Once per hour (at 00 minutes and 00
Seconds of every hour)
Once per month (at 00 hours, 00 minutes,
and 00 seconds of first day of every month)
(Default)
*1) Pulse Mode:
2-Hz and 1-Hz clock pulses are output in synchronization with the increment of the second counter as
illustrated in the timing chart below.
CTFG Bit
INTR Pin
Approx. 92µs
(Increment of second counter)
Rewriting of the second counter
In the pulse mode, the increment of the second counter is delayed by approximately 92 µs from the falling
edge of clock pulses. Consequently, time readings immediately after the falling edge of clock pulses may
appear to lag behind the time counts of the real-time clocks by approximately 1 second. Rewriting the
second counter will reset the other time counters of less than 1 second, driving the INTR pin low.
*2) Level Mode:
Periodic interrupt signals are output with selectable interrupt cycle settings of 1 second, 1 minute, 1 hour,
and 1 month. The increment of the second counter is synchronized with the falling edge of periodic
interrupt signals. For example, periodic interrupt signals with an interrupt cycle setting of 1 second are
output in synchronization with the increment of the second counter as illustrated in the timing chart below.
40
R2033K/T
CTFG Bit
INTR Pin
Setting CTFG bit to 0
(Increment of
second counter)
(Increment of
second counter)
Setting CTFG bit to 0
(Increment of
second counter)
*1), *2) When the oscillation adjustment circuit is used, the interrupt cycle will fluctuate once per 20sec. as
follows:
Pulse Mode: The “L” period of output pulses will increment or decrement by a maximum of ±3.784ms. For
example, 1-Hz clock pulses will have a duty cycle of 50 ±0.3784%.
Level Mode: A periodic interrupt cycle of 1 second will increment or decrement by a maximum of ±3.784ms.
•
32-kHz CLOCK OUTPUT
For the R2033K/T, 32.768-kHz clock pulses are output from the 32KOUT pin when either the CLEN1 bit in the
Control Register 2 or the CLEN2 bit in the Control Register 1 is set to 0 when the CLKC pin is set to high. If
the condition is not satisfied, the output is set to low.
CLEN1
(D3 at Address Fh)
1
*
0(Default)
*
CLEN2
(D4 at Address Eh)
1
*
*
0(Default)
CLKC pin input
*
0
1
1
32KOUT PIN
(CMOS push-pull output)
“L”
Clock pulses
The 32KOUT pin output is synchronized with the CLEN1 and CLEN2 bit and CLKC pin settings as
illustrated in the timing chart below.
CLKC pin or CLEN1 or
CLEN2 bit setting
32KOUT PIN
Max.62.0µs
41
R2033K/T
Typical Applications
•
Typical Power Circuit Configurations
Sample circuit configuration 1
R1163xxx1B is a series regulator with the reverse current protection circuit. The CE pin should be pull-up to
system power supply voltage, and ECO pin should be connect to system power supply or VSS. Please select
VOUT voltage equal to the CPU power supply voltage that interfaces to R2033K/T and SRAM.
System Power Supply
VDD
VOUT
VDD
R1163xxx1B
CE
SRAM
etc.
Primary
Battery
VSS
VSS
Sample circuit configuration 2
System power supply
OSCIN
OSCOUT
32768Hz
VDD
Primary
Battery
VSS
System power supply
OSCIN
OSCOUT
32768Hz
VDD
VSS
42
ECO
Secondary
Battery
*1) Install bypass capacitors for
high-frequency and low-frequency
applications in parallel in close
vicinity to the R2033K/T.
R2033K/T
•
Connection of INTR Pin
The INTR pin follows the N-channel open drain output logic and contains no protective diode on the power
supply side. As such, it can be connected to a pull-up resistor of up to 5.5v regardless of supply voltage.
System power supply
A
INTR
*1)
B
OSCIN
OSCOUT
Backup power supply
32768Hz
*1) Depending on whether the INTR pin is
used during battery backup, it should be
connected to a pull-up resistor at the following
different positions:
(1) Position A in the left diagram when it is not to
be used during battery backup.
(2) Position B in the left diagram when it is to be
used during battery backup.
VDD
VSS
•
Connection of 32KOUT Pin
As the 32KOUT pin is CMOS output, the supply voltage of the R2033K/T and any devices to be connected
should be the same. When the device is powered down, the 32KOUT output pin should be disabled.
When the CLKC pin is connected to the system power supply through the pull-up resistor, the pull-up resistor
should be 0Ω to 10kΩ, and the 32KOUT pin should be connect to the host device through the resistor (approx.
10kΩ)
CLKC
R3111
XXXXC
0 to 10KΩ
CPU Power Supply
CPU Power Supply
CLKC
CPU
32KOUT
32KOUT
Approx.10KΩ
Back-up Power Supply
Back-up Power supply
VDD
VDD
VSS
VSS
43
R2033K/T
Typical Characteristics
Test circuit
X’tal : 32.768kHz
(R1=50kΩ typ)
(CL=6pF to 9pF)
Topt : 25°C
Output pins : Open
VDD
CGOUT
OSCIN
32768Hz
OSCOUT
CDOUT
Frequency
Counter
32KOUT
VSS
Timekeeping Current vs. Supply Voltage
(with 32kHz clock output)
(Output=Open, Topt=25°C)
1
0.8
(CGout, CDout)=(5pF, 5pF)
0.6
0.4
(CGout, CDout)=(0pF, 0pF)
0.2
0
0
1
2
3
4
5
Timekeeping Current IDD(uA)
Timekeeping Current IDD(uA)
Timekeeping Current vs. Supply Voltage
(with no 32kHz clock output)
(Output=Open, Topt=25°C)
3
2.5
(CGout, CDout)=(5pF, 5pF)
2
1.5
1
(CGout, CDout)=(0pF, 0pF)
0.5
0
6
0
1
Supply Vlotage VDD(v)
VDD=5v
VDD=3v
0
200
400
600
800
SCL Clock Frequency (kHz)
44
3
4
5
6
Timekeeping Current vs. Operating Temperature
(Output pins=Open, CGout=CDout=0pF)
Timekeeping Current IDD(uA)
CPU Access Current IDD(uA)
CPU Access Current vs. SCLK Clock Frequency
(Output pins=Open, Topt=25°C, CGout=CDout=0pF)
80
70
60
50
40
30
20
10
0
2
Supply Voltage VDD(v)
1000
2
1.8
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
with 32kHz clock output
with no 32kHz clock output
-50
-25
0
25
50
75
100
Operating Temperature Topt(Celcius)
R2033K/T
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
CDout=0pF
CDout=5pF
0
5
10
15
20
Oscillation Frequency Deviation vs. Supply Voltage
(Topt=25°C,VDD=3v as standard)
Oscillation Frequency Deviation
(ppm)
Oscillation Frequency Deviation
(ppm)
Oscillation Frequency Deviation vs. External CGout
(VDD=3v, Topt=25°C, CGout=CDout=0pF as standard)
5
4
3
2
1
0
-1
-2
-3
-4
-5
0
External CGout (pF)
2
3
4
5
6
Supply Voltage VDD (v)
VOL vs. IOL ( INTR pin)
(Topt=25°C)
Oscillation Frequency Deviation vs.
Operating Temperature
(VDD=3V, Topt=25°C as standard)
30
20
0
-20
-40
-60
-80
-100
-120
25
IOL (mA)
Oscillation Frequency Deviation
(ppm)
1
VDD=5v
20
VDD=3v
15
10
VDD=1.5v
5
-60 -40 -20 0 20 40 60 80 10
0
Operating TemperatureTopt(Celsius)
0
0
0.1
0.2
0.3
0.4
0.5
VOL (v)
45
R2033K/T
Typical Software-based Operations
•
Initialization at Power-on
Start
*1)
Power-on
*2)
PON=1?
Yes
No
*3)
*4)
VDET=0?
Set Oscillation Adjustment
Register and Control
Register 1 and 2, etc.
No
Yes
Warning Back-up
Battery Run-down
*1) After power-on from 0 volt, the start of oscillation and the process of internal initialization require a time
span on 1to 2seconds, so that access should be done after the lapse of this time span or more.
*2) The PON bit setting of 0 in the Control Register 1 indicates power-on from backup battery and not from
0v. For further details, see "P.35 • PON, XST , VDET".
*3) This step is not required when the supply voltage monitoring circuit is not used.
*4) This step involves ordinary initialization including the Oscillation Adjustment Register and interrupt cycle
settings, etc.
•
Writing of Time and Calendar Data
*1)
CE←H
Write to Time Counter and
Calendar Counter
CE←L
46
*1) When writing to clock and calendar counters, do not insert CE=L
until all times from second to year have been written to prevent
error in writing time. (Detailed in "P.24 •Considerations in
Reading and Writing Time Data under special condition".
*2)
*2) Any writing to the second counter will reset divider units lower
than the second digits.
*3)
The R2033K/T may also be initialized not at power-on but in the
process of writing time and calendar data.
R2033K/T
•
Reading Time and Calendar Data
(1) Ordinary Process of Reading Time and Calendar Data
CE←H
*1) When reading to clock and calendar counters, do not insert
CE=L until all times from second to year have been read to
prevent error in reading time. (Detailed in "P.24
•Considerations in Reading and Writing Time Data under
special condition".
*1)
Read from Time Counter
and Calendar Counter
CE←L
*1)
(2) Basic Process of Reading Time and Calendar Data with Periodic Interrupt Function
Set Periodic Interrupt
Cycle Selection Bits
*1)
Generate Interrupt in CPU
No
CTFG=1?
Yes
*2)
Other Interrupt
Processes
*1) This step is intended to select the level mode
as a waveform mode for the periodic interrupt
function.
*2) This step must be completed within 0.5
second.
*3) This step is intended to set the CTFG bit to 0
in the Control Register 2 to cancel an interrupt
to the CPU.
Read from Time Counter
and Calendar Counter
*3)
Control Register 2
←(X1X1X011)
47
R2033K/T
(3) Applied Process of Reading Time and Calendar Data with Periodic Interrupt Function
Time data need not be read from all the time counters when used for such ordinary purposes as time count
indication. This applied process can be used to read time and calendar data with substantial reductions in the
load involved in such reading.
For Time Indication in "Day-of-Month, Day-of-week, Hour, Minute, and Second" Format:
Control Register 1←
(XXXX0100)
Control Register 2←
(X1X1X011)
*1)
Generate interrupt to CPU
Yes
*2)
Sec.=00?
No
Yes
Read Min.,Hr.,Day,
and Day-of-week
Control Register 2←
(X1X1X011)
48
Other interrupts
Processes
No
CTFG=1?
*3)
Use Previous Min.,Hr.,
Day,and Day-of-week data
*4)
*1) This step is intended to select the
level mode as a waveform mode for
the periodic interrupt function.
*2) This step must be completed within
0.5 sec.
*3) This step is intended to read time
data from all the time counters only
in the first session of reading time
data after writing time data.
*4) This step is intended to set the
CTFG bit to 0 in the Control
Register 2 to cancel an interrupt to
the CPU.
R2033K/T
•
Interrupt Process
(1) Periodic Interrupt
Set Periodic Interrupt
Cycle Selection Bits
*1)
Generate Interrupt to CPU
No
CTFG=1?
Yes
Other Interrupt
Processes
*1) This step is intended to select the level mode
as a waveform mode for the periodic interrupt
function.
*2) This step is intended to set the CTFG bit to 0
in the Control Register 2 to cancel an
interrupt to the CPU.
Conduct
Periodic Interrupt
*2)
Control Register 2←
(X1X1X011)
49
R2033K/T
(2) Alarm Interrupt
WALE or DALE←0
*1)
Set Alarm Min., Hr., and
Day-of-week Registers
WALE or DALE←1
*2)
Generate Interrupt to CPU
No Other Interrupt
WAFG or DAFG=1?
Processes
Yes
Conduct Alarm Interrupt
*3)
Control Register 2 ←
(X1X1X101)
50
*1) This step is intended to once disable the alarm
interrupt circuit by setting the WALE or DALE bits
to 0 in anticipation of the coincidental occurrence
of a match between current time and preset
alarm time in the process of setting the alarm
interrupt function.
*2) This step is intended to enable the alarm
interrupt function after completion of all alarm
interrupt settings.
*3) This step is intended to once cancel the alarm
interrupt function by writing the settings of
"X,1,X, 1,X,1,0,1" and "X,1,X,1,X,1,1,0" to the
Alarm_W Registers and the Alarm_D Registers,
respectively.