DATA SHEET GENERAL PURPOSE CHIP RESISTORS RC0201 5%, 1%, 0.5% Product specification – May 02, 2011 V.8 Supersedes Date of Mar. 06, 2003 RoHS compliant & Halogen free Product specification Chip Resistor Surface Mount RC 9 SCOPE ORDERING INFORMATION - GLOBAL PART NUMBER & 12NC This specification describes RC0201 series chip resistors with lead-free terminations made by thick film process. Both part numbers are identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and resistance value. YAGEO BRAND ordering code GLOBAL PART NUMBER APPLICATIONS All general purpose application RC0201 compliant - Products with lead free terminations meet RoHS requirements. - Pb-glass contained in electrodes, resistor element and glass are exempted by RoHS. F = ±1% J = ±5% (for Jumper ordering, use code of J) (2) PACKAGING TYPE R = Paper / PE taping reel (3) TEMPERATURE COEFFICIENT OF RESISTANCE – = Based on spec. (4) TAPING REEL 07 = 7 inch dia. Reel 7C = 7 inch dia. Reel, 1.5 x Standard Quantity High component and equipment reliability None forbidden-materials used in products/production. (6) D = ±0.5% environmentally hazardous wastes of PCB space (5) (1) TOLERANCE Reduce Save ( PREFERRED ) X R - XX XXXX L (1) (2) (3) (4) FEATURES Halogen Free Epoxy RoHS 2 0201 SERIES 7D = 7 inch dia. Reel, 2 x Standard Quantity 13 = 13 inch dia. Reel (5) RESISTANCE VALUE There are 2~4 digits indicated the resistance value. Letter R/K/M is decimal point, no need to mention the last zero after R/K/M, e.g.1K2, not 1K20. Detailed coding rules of resistance are shown in the table of “Resistance rule of global part number”. (6) DEFAULT CODE Letter L is system default code for ordering only. (Note) Resistance rule of global part number Resistance code rule Example D1 D1 = Dummy 0R 0R = Jumper XRXX (1 to 9.76 Ω) 1R = 1 Ω 1R5 = 1.5 Ω 9R76 = 9.76 Ω XXRX (10 to 97.6 Ω) 10R = 10 Ω 97R6 = 97.6 Ω XXXR (100 to 976 Ω) 100R = 100 Ω XKXX (1 to 9.76 KΩ) 1K = 1,000 Ω 9K76 = 9760 Ω XMXX (1 to 9.76 MΩ) 1M = 1,000,000 Ω 9M76= 9,760,000 Ω ORDERING EXAMPLE The ordering code of a RC0201 chip resistor, value 56 X with ±1% tolerance, supplied in 7-inch tape of 15,000 units per reel is: RC0201FR-7C56RL. NOTE 1. All our RSMD products meet RoHS compliant and Halogen Free. "LFP" of the internal 2D reel label mentions "Lead Free Process". 2. On customized label, "LFP" or specific symbol can be printed. www.yageo.com May 02, 2011 V.8 Product specification Chip Resistor Surface Mount RC SERIES 3 9 0201 PHYCOMP BRAND ordering codes Both GLOBAL PART NUMBER (preferred) and 12NC (traditional) codes are acceptable to order Phycomp brand products. GLOBAL PART NUMBER ( PREFERRED ) For detailed information of GLOBAL PART NUMBER and ordering example, please refer to page 2. 12NC CODE 2322 XXX XXXXX L (1) TYPE/ START 0201 IN (1) (2) (3) Last digit of 12NC Resistance decade (3) (4) TOL. RESISTANCE (%) RANGE PAPER / PE TAPE ON REEL (units) (2) 10,000 20,000 50,000 RC41 2322 ±5% 1 to 1 MΩ 803 70xxx 806 80xxx 803 60xxx RC42 2322 ±1% 1 to 1 MΩ 806 7xxxx 806 8xxxx 806 6xxxx Jumper 2322 - 0Ω 803 91001 --- --- Dummy 2322 - - 803 93001 --- --- Last digit 0.01 to 0.0976 X 0.1 to 0.976 X 0 1 to 9.76 X 8 10 to 97.6 X 9 100 to 976 X 1 1 to 9.76 KX 2 7 10 to 97.6 KX (1) The resistors have a 12-digit ordering code starting with 2322. 3 100 to 976 KX 4 (2) The subsequent 4 or 5 digits indicate the resistor tolerance and packaging. 1 to 9.76 MX 5 10 to 97.6 MX 6 (3) The remaining 4 or 3 digits represent the resistance value with the last digit indicating the multiplier as shown in the table of “Last digit of 12NC”. (4) Letter L is system default code for order only. (Note) ORDERING EXAMPLE The ordering code of a RC42 resistor, value 56 X with ±1% tolerance, supplied in tape of 10,000 units per reel is: 232280675609L or RC0201FR-0756RL. Example: 0.02 X = 0200 or 200 0.3 X = 3007 or 307 1X = 1008 or 108 33 KX = 3303 or 333 10 MX = 1006 or 106 NOTE 1. All our RSMD products meet RoHS compliant and Halogen Free. "LFP" of the internal 2D reel label mentions "Lead Free Process". 2. On customized label, "LFP" or specific symbol can be printed. www.yageo.com May 02, 2011 V.8 Product specification Chip Resistor Surface Mount RC SERIES 4 9 0201 MARKING RC0201 No marking ynsc007 Fig. 1 For further marking information, please refer to data sheet “Chip resistors marking”. CONSTRUCTION The resistor is constructed on top of a high-grade ceramic body. Internal metal electrodes are added on each end to make the contacts to the thick film resistive element. The composition of the resistive element is a noble metal imbedded into a glass and covered by a second glass to prevent environment influences. The resistor is laser trimmed to the rated resistance value. The resistor is covered with a protective epoxy coat, finally the two external terminations (matte tin on Ni-barrier) are added, as shown in Fig.2. OUTLINES For dimension, please refer to Table 1 overcoat protective glass resistive layer (Jumper chip is a conductor) inner electrode H termination(Ni/matte tin) inner electrode ceramic substrate I2 overcoat I1 W YNSC056 L DIMENSIONS Table 1 TYPE RC0201 L (mm) 0.60 ±0.03 W (mm) 0.30 ±0.03 H (mm) 0.23 ±0.03 I1 (mm) 0.10 ±0.05 I2 (mm) 0.15 ±0.05 Fig. 2 Chip resistor outlines www.yageo.com May 02, 2011 V.8 Product specification Chip Resistor Surface Mount RC SERIES 5 9 0201 ELECTRICAL CHARACTERISTICS FOOTPRINT AND SOLDERING PROFILES Table 2 RC0201 1/20 W CHARACTERISTICS Operating Temperature Range –55 °C to +125 °C Maximum Working Voltage 25 V Maximum Overload Voltage 50 V Dielectric Withstanding Voltage 50 V For recommended footprint and soldering profiles, please refer to data sheet “Chip resistors mounting”. 5% (E24) 1 Ω to 10 MΩ 1% (E24/E96) 1 Ω to 10 MΩ Resistance Range 0.5% (E24/E96) 10 Ω to 1 MΩ Jumper < 0.05 Ω Temperature Coefficient 1 Ω ≤ R ≤ 10 Ω -100/+350 ppm/°C 10 Ω < R ≤ 10 MΩ ±200 ppm/°C Rated Current 0.5 A Maximum Current 1.0 A Jumper Criteria PACKING STYLE AND PACKAGING QUANTITY Table 3 Packing style and packaging quantity PRODUCT TYPE PACKING STYLE REEL DIMENSION RC0201 Paper / PE Taping Reel (R) 7" (178 mm) QUANTITY PER REEL 10,000/15,000/20,000 units 13" (330 mm) 50,000 units NOTE 1. For paper/PE tape and reel specification/dimensions, please refer to data sheet “Chip resistors packing”. 2. For size of 0201, standard quantity is 10,000 units per reel. FUNCTIONAL DESCRIPTION POWER RATING RC0201 rated power at 70°C is 1/20 W RATED VOLTAGE The DC or AC (rms) continuous working voltage corresponding to the rated power is determined by the following formula: V=√(P X R) or max. working voltage whichever is less Where V=Continuous rated DC or AC (rms) working voltage (V) handbook, halfpage MLB206_1 P (%Prated ) 100 50 0 55 0 50 70 100 125 o Tamb ( C) Fig. 3 Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (Tamb) P=Rated power (W) R=Resistance value (X) www.yageo.com May 02, 2011 V.8 Product specification Chip Resistor Surface Mount RC SERIES 6 9 0201 TESTS AND REQUIREMENTS Table 4 Test condition, procedure and requirements TEST TEST METHOD PROCEDURE REQUIREMENTS Temperature Coefficient of Resistance (T.C.R.) IEC 60115-1 4.8 At +25/–55 °C and +25/+125 °C Refer to table 2 Formula: R2–R1 T.C.R= ------------------------- ×106 (ppm/°C) R1(t2–t1) Where t1=+25 °C or specified room temperature t2=–55 °C or +125 °C test temperature R1=resistance at reference temperature in ohms R2=resistance at test temperature in ohms Life/Endurance IEC 60115-1 4.25.1 At 70±5 °C for 1,000 hours, RCWV applied for 1.5 hours on, 0.5 hour off, still air required ±(1.0%+0.05 Ω) for 1%, 0.5% tol. ±(3.0%+0.05 Ω for 5% tol. <100 mΩ for Jumper High Temperature Exposure/ Endurance at Upper Category Temperature IEC 60068-2-2 Moisture Resistance MIL-STD-202G Method-106G 1,000 hours at 125±5 °C, unpowered ±(1.0%+0.05 Ω) for 1%, 0.5% tol. ±(2.0%+0.05 Ω) for 5% tol. <50 mΩ for Jumper Each temperature / humidity cycle is defined at 8 hours, 3 cycles / 24 hours for 10d. with 25 °C / 65 °C 95% R.H, without steps 7a & 7b, unpowered ±(0.5%+0.05 Ω) for 1%, 0.5% tol. Parts mounted on test-boards, without condensation on parts <100 mΩ for Jumper ±(2.0%+0.05 Ω) for 5% tol. Measurement at 24±2 hours after test conclusion Thermal Shock MIL-STD-202G Method-107G -55/+125 °C Number of cycles required is 300. Devices unmounted Maximum transfer time is 20 seconds. Dwell time is 15 minutes. Air – Air ±(0.5%+0.05 Ω) for 1%, 0.5% tol. ±(1%+0.05 Ω) for 5% tol. <50 mΩ for Jumper www.yageo.com May 02, 2011 V.8 Product specification Chip Resistor Surface Mount RC SERIES 7 9 0201 TEST TEST METHOD PROCEDURE REQUIREMENTS Short Time Overload IEC60115-1 4.13 2.5 times of rated voltage or maximum overload voltage whichever is less for 5 sec at room temperature ±(1.0%+0.05 Ω) for 1%, 0.5% tol. ±(2.0%+0.05 Ω) for 5% tol. <50 mΩ for Jumper No visible damage Board Flex/ Bending IEC 60068-2-21 Chips mounted on a 90mm glass epoxy resin PCB (FR4) ±(1.0%+0.05 Ω) 5 mm bending No visible damage <50 mΩ for Jumper Bending time: 60±5 seconds Low Temperature Operation IEC 60068-2-1 The resistor shall be subjected to a DC rated voltage for 1.5 h-on, 0.5 h-off, at -55±3 °C ±(0.5%+0.05 Ω) for 1%, 0.5% tol. This constitutes shall be repeated for 96 hours ±(1.0%+0.05 Ω) for 5% tol. However the applied voltage shall not exceed the maximum operating voltage Insulation Resistance IEC 60115-1 4.6 Rated continuous overload voltage (RCOV) for 1 minute Type Voltage (DC) Dielectric Withstand Voltage IEC 60115-1 4.7 Resistance to Solvent IPC/JEDEC J-STD-020D Noise Voltage (AC) IEC 60115-1 4.12 ≥10 GΩ RC0201 50 V Maximum voltage (Vrms) applied for 1 minute Type No visible damage No breakdown or flashover RC0201 50 Vrms lsopropylalcohol (C3H7OH) followed by brushing No smeared Maximum voltage (Vrms) applied Resistors range Value R < 100 Ω 10 dB 100 Ω ≤ R < 1 KΩ 20 dB 1 KΩ ≤ R < 10 KΩ 30 dB 10 KΩ ≤ R < 100 KΩ 40 dB 100 KΩ ≤ R < 1 MΩ 46 dB 1 MΩ ≤ R ≤ 22 MΩ 48 dB www.yageo.com May 02, 2011 V.8 Product specification Chip Resistor Surface Mount RC SERIES 8 9 0201 TEST TEST METHOD PROCEDURE REQUIREMENTS Humidity IEC 60115-1 4.21 Steady state for 1000 hours at 40 °C / 95% R.H. RCWV applied for 1.5 hours on and 0.5 hour off ±(1.0%+0.05 Ω) for 1%, 0.5% tol. ±(2.0%+0.05 Ω) for 5% tol. <100 mΩ for Jumper Intermittent Overload IEC 60115-1 4.39 2.5 times of rated voltage or maximum overload voltage whichever is less for 1 second on and 25 seconds off; total 10,000 cycles ±(1.0%+0.05 Ω) for 1%, 0.5% tol. ±(2.0%+0.05 Ω) for 5% tol. <100 mΩ for Jumper Solderability - Wetting IPC/JEDEC J-STD-002B test B Electrical Test not required Well tinned (≥95% covered) Magnification 50X No visible damage SMD conditions: 1st step: method B, aging 4 hours at 155 °C dry heat 2nd step: lead-free solder bath at 245±3 °C Dipping time: 3±0.5 seconds - Leaching IPC/JEDEC J-STD-002B test D Lead-free solder, 260 °C, 30 seconds immersion time No visible damage - Resistance to Soldering Heat IEC 60068-2-58 Condition B, no pre-heat of samples ±(0.5%+0.05 Ω) for 1%, 0.5% tol. Lead-free solder, 260 °C, 10 seconds immersion time Procedure 2 for SMD: devices fluxed and cleaned with isopropanol ±(1.0%+0.05 Ω) for 5% tol. <50 mΩ for Jumper No visible damage www.yageo.com May 02, 2011 V.8 Product specification Chip Resistor Surface Mount RC SERIES 9 9 0201 REVISION HISTORY REVISION DATE CHANGE NOTIFICATION DESCRIPTION Version 8 May 02, 2011 - - Add ±0.5% tolerance for RC0201 - Add new taping reel code of 7 inch dia. reel with 1.5 x standard quantity (15,000 units per reel) - 10" taping reel removed Version 7 Jan 06, 2011 - - Typo updated Version 6 Apr 27, 2010 - - Updated test items and methods - Add new taping reel code of 7 inch dia. reel with double standard quantity (20,000 units per reel) Version 5 Nov 10, 2009 - - Test items and methods updated - Test requirements upgraded - Resistance range extend Version 4 Jul 15, 2008 - - Description of "Halogen Free Epoxy" added - Define global part number Version 3 Apr 25, 2007 - - New datasheet for 0201 thick film 1% and 5% with lead-free terminations - Replace the 0201 part of pdf files: Pu-RC0201_51_PbFree_L_2 and YuRC0201_51_PbFree_L_2 - Max. working voltage, resistance rage, and TCR updated - Tests and Requirements updated Version 2 Sep 03, 2004 - - New datasheet for 0201 thick film 1% and 5% with lead-free terminations - Replace the 0201 part of pdf files: RC41_5_4, RC42_1_1 - Test method and procedure updated - PE tape added (paper tape will be replaced by PE tape) “ Yageo reserves all the rights for revising the content of this datasheet without further notification, as long as the products itself are unchanged. Any product change will be announced by PCN.” www.yageo.com May 02, 2011 V.8