BB REG102GA

REG
102
REG102
REG
102
SBVS024F – NOVEMBER 2000 – REVISED SEPTEMBER 2005
DMOS
250mA Low-Dropout Regulator
FEATURES
DESCRIPTION
● NEW DMOS TOPOLOGY:
Ultra Low Dropout Voltage:
150mV typ at 250mA
Output Capacitor not Required for Stability
The REG102 is a family of low-noise, low-dropout linear
regulators with low ground pin current. The new DMOS
topology provides significant improvement over previous
designs, including low-dropout voltage (only 150mV typ at
full load), and better transient performance. In addition, no
output capacitor is required for stability, unlike conventional
low-dropout regulators that are difficult to compensate and
require expensive low ESR capacitors greater than 1µF.
●
●
●
●
●
●
●
●
●
FAST TRANSIENT RESPONSE
VERY LOW NOISE: 28µVrms
HIGH ACCURACY: ±1.5% max
HIGH EFFICIENCY:
IGND = 600µA at IOUT = 250mA
Not Enabled: IGND = 0.01µA
2.5V, 2.8V, 2.85V, 3.0V, 3.3V, AND 5.0V
ADJUSTABLE OUTPUT VERSIONS
OTHER OUTPUT VOLTAGES AVAILABLE UPON
REQUEST
FOLDBACK CURRENT LIMIT
THERMAL PROTECTION
SMALL SURFACE-MOUNT PACKAGES:
SOT23-5, SOT223-5, and SO-8
Typical ground pin current is only 600µA (at IOUT = 250mA)
and drops to 10nA when not enabled. Unlike regulators with
PNP pass devices, quiescent current remains relatively constant over load variations and under dropout conditions.
The REG102 has very low output noise (typically 28µVrms
for VOUT = 3.3V with CNR = 0.01µF), making it ideal for use
in portable communications equipment. On-chip trimming
results in high output voltage accuracy. Accuracy is maintained over temperature, line, and load variations. Key parameters are tested over the specified temperature range
(–40°C to +85°C).
The REG102 is well protected—internal circuitry provides a
current limit that protects the load from damage; furthermore,
thermal protection circuitry keeps the chip from being damaged by excessive temperature. The REG102 is available in
SOT23-5, SOT223-5, and SO-8 packages.
APPLICATIONS
●
●
●
●
●
●
PORTABLE COMMUNICATION DEVICES
BATTERY-POWERED EQUIPMENT
PERSONAL DIGITAL ASSISTANTS
MODEMS
BAR-CODE SCANNERS
BACKUP POWER SUPPLIES
Enable
Enable
VOUT
VIN
+
0.1µF
NR
REG102
(Fixed Voltage
Versions)
+
COUT
(1)
VIN
VOUT
+
REG102-A
+
COUT(1)
Adj
GND
NR = Noise Reduction
0.1µF
R1
GND
R2
NOTE: (1) Optional.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
Copyright © 2000-2005, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
ABSOLUTE MAXIMUM RATINGS(1)
ELECTROSTATIC
DISCHARGE SENSITIVITY
Supply Input Voltage, VIN ....................................................... –0.3V to 12V
Enable Input Voltage, VEN ....................................................... –0.3V to VIN
Feedback Voltage, VFB ........................................................ –0.3V to 6.0V
NR Pin Voltage, VNR ............................................................. –0.3V to 6.0V
Output Short-Circuit Duration ...................................................... Indefinite
Operating Temperature Range (TJ) ................................ –55°C to +125°C
Storage Temperature Range (TA) ................................... –65°C to +150°C
Lead Temperature (soldering, 3s) .................................................. +240°C
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
NOTE: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may degrade
device reliability.
PACKAGE/ORDERING INFORMATION(1)
VOUT(2)
PRODUCT
REG102xx-yyyy/zzz
XX is package designator.
YYYY is typical output voltage (5 = 5.0V, 2.85 = 2.85V, A = Adjustable).
ZZZ is package quantity.
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com.
(2) Output voltages from 2.5V to 5.1V in 50mV increments are available; minimum order quantities apply. Contact factory for details and availability.
PIN CONFIGURATIONS
Top View
SOT23-5
VIN
1
GND
2
Enable
3
SO-8
SOT223-5
5
4
VOUT
Tab is GND
NR/Adjust(1)
1
2
3
4
VOUT(2)
1
8
VIN(3)
VOUT(2)
2
7
VIN(3)
NR/Adjust(1)
3
6
NC
GND
4
5
Enable
5
(N Package)
VIN
VOUT
GND
Enable
NR/Adjust(1)
(U Package)
(G Package)
NOTES: (1) For REG102A-A: voltage setting resistor pin.
All other models: noise reduction capacitor pin.
(2) Both pin 1 and pin 2 must be connected.
(3) Both pin 7 and pin 8 must be connected.
2
REG102
www.ti.com
SBVS024F
ELECTRICAL CHARACTERISTICS
Boldface limits apply over the specified temperature range, TJ = –40°C to +85°C.
At TJ = +25°C, VIN = VOUT + 1V (VOUT = 2.5V for REG102-A), VENABLE = 1.8V, IOUT = 5mA, CNR = 0.01µF, and COUT = 0.1µF(1), unless otherwise noted.
REG102NA
REG102GA
REG102UA
PARAMETER
OUTPUT VOLTAGE
Output Voltage Range
REG102-2.5
REG102-2.8
REG102-2.85
REG102-3.0
REG102-3.3
REG102-5
REG102-A
Reference Voltage
Adjust Pin Current
Accuracy
Over Temperature
vs Temperature
vs Line and Load
Over Temperature
DC DROPOUT VOLTAGE(2)
For all models
Over Temperature
VOLTAGE NOISE
f = 10Hz to 100kHz
Without CNR (all models)
With CNR (all fixed voltage models)
OUTPUT CURRENT
Current Limit(3)
Over Temperature
Short-Circuit Current Limit
CONDITION
MIN
2.5
2.8
2.85
3.0
3.3
5
2.5
dVOUT/dT
50
±0.8
IOUT = 5mA to 250mA, VIN = (VOUT + 0.4V) to 10V
VIN = (VOUT + 0.6V) to 10V
VDROP
TEMPERATURE RANGE
Specified Range
Operating Range
Storage Range
Thermal Resistance
SOT23-5 Surface-Mount
SO-8 Surface-Mount
SOT223-5 Surface-Mount
±2.8
IOUT = 5mA
IOUT = 250mA
IOUT = 250mA
4
150
10
220
270
mV
mV
mV
CNR = 0, COUT = 0
CNR = 0.01µF, COUT = 10µF
23µVrms/V • VOUT
7µVrms/V • VOUT
1
±1.5
±2.3
±2.0
Vn
ICL
340
300
ISC
VENABLE
IENABLE
400
150
mA
mA
mA
65
dB
1.8
–0.2
VENABLE = 1.8V to VIN, VIN = 1.8V to
VENABLE = 0V to 0.5V
COUT = 1.0µF, RLOAD = 13Ω
COUT = 1.0µF, RLOAD = 13Ω
6.5(4)
µVrms
µVrms
1
2
50
1.5
470
490
VIN
0.5
100
100
IGND
V
V
nA
nA
µs
ms
°C
°C
160
140
Enable Pin Low
INPUT VOLTAGE
Operating Input Voltage Range(5)
Specified Input Voltage Range
Over Temperature
UNITS
V
V
V
V
V
V
V
V
µA
%
%
ppm/°C
%
%
5.5
1.26
0.2
±0.5
VREF
IADJ
THERMAL SHUTDOWN
Junction Temperature
Shutdown
Reset from Shutdown
GROUND PIN CURRENT
Ground Pin Current
MAX
VOUT
RIPPLE REJECTION
f = 120Hz
ENABLE CONTROL
VENABLE High (output enabled)
VENABLE Low (output disabled)
IENABLE High (output enabled)
IENABLE Low (output disabled)
Output Disable Time
Output Enable Softstart Time
TYP
500
800
0.2
µA
µA
µA
1.8
VOUT + 0.4
VOUT + 0.6
10
10
10
V
V
V
–40
–55
–65
+85
+125
+150
°C
°C
°C
IOUT = 5mA
IOUT = 250mA
VENABLE ≤ 0.5V
400
600
0.01
VIN
VIN > 1.8V
VIN > 1.8V
TJ
TJ
TA
θJA
θJA
θJC
θJA
Junction-to-Ambient
Junction-to-Ambient
Junction-to-Case
Junction-to-Ambient
200
150
15
See Figure 8
°C/W
°C/W
°C/W
°C/W
NOTES: (1) The REG102 does not require a minimum output capacitor for stability, however, transient response can be improved with proper capacitor selection.
(2) Dropout voltage is defined as the input voltage minus the output voltage that produces a 2% change in the output voltage from the value at VIN = VOUT
+ 1V at fixed load.
(3) Current limit is the output current that produces a 10% change in output voltage from VIN = VOUT + 1V and IOUT = 5mA.
(4) For VENABLE > 6.5V, see typical characteristic IENABLE vs VENABLE.
(5) The REG102 no longer regulates when VIN < VOUT + VDROP (MAX). In dropout, the impedance from VIN to VOUT is typically less than 1Ω at TJ = +25°C.
REG102
SBVS024F
www.ti.com
3
TYPICAL CHARACTERISTICS
For all models, at TJ = +25°C and VENABLE = 1.8V, unless otherwise noted.
LOAD REGULATION vs TEMPERATURE
(VIN = VOUT + 1V)
0.80
0
0.60
–0.1
Output Voltage Change (%)
Output Voltage Change (%)
OUTPUT VOLTAGE CHANGE vs IOUT
(VIN = VOUT + 1V, Output Voltage % Change
Referred to IOUT = 125mA at +25°C)
0.40
+25°C
0.20
+125°C
0
–0.20
–0.40
–55°C
–0.60
–0.2
–0.4
25
50
75
100
125
150
175 200
5mA < IOUT < 250mA
–0.5
–0.6
–0.80
0
25mA < IOUT < 250mA
–0.3
–0.7
–50
225 250
–25
0
25
IOUT (mA)
LINE REGULATION
(Referred to VIN = VOUT + 1V at IOUT = 125mA)
75
100
125
LINE REGULATION vs TEMPERATURE
0
20
All Fixed Output
Voltage Versions
15
10
IOUT = 250mA
Output Voltage Change (%)
Output Voltage Change (mV)
50
Temperature (°C)
IOUT = 5mA
5
IOUT = 125mA
0
–5
–10
–15
–0.05
–0.10
–0.20
–0.25
(VOUT + 0.4V) < VIN < 10V
IOUT = 250mA
–20
0
1
2
3
4
5
(VOUT + 1V) < VIN < 10V
–0.15
6
7
–0.30
–50
8
–25
0
25
50
75
100
125
Temperature (°C)
VIN – VOUT (V)
DC DROPOUT VOLTAGE vs TEMPERATURE
DC DROPOUT VOLTAGE vs IOUT
250
250
200
DC Dropout Voltage (mV)
DC Dropout Voltage (mV)
IOUT = 250mA
+125°C
150
+25°C
100
–55°C
50
50
100
150
200
250
100
50
–25
0
25
50
75
100
125
Temperature (°C)
IOUT (mA)
4
150
0
–50
0
0
200
REG102
www.ti.com
SBVS024F
TYPICAL CHARACTERISTICS (Cont.)
For all models, at TJ = +25°C and VENABLE = 1.8V, unless otherwise noted.
OUTPUT VOLTAGE DRIFT HISTOGRAM
OUTPUT VOLTAGE ACCURACY HISTOGRAM
30
18
16
Percentage of Units (%)
Percentage of Units (%)
25
14
12
10
8
6
4
20
15
10
5
2
0
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
1.0
0.8
0.6
0.4
0.2
0.0
–0.2
–0.4
–0.6
–0.8
–1.0
0
Error (%)
VOUT Drift (ppm/°C)
OUTPUT VOLTAGE vs TEMPERATURE
(Output Voltage % Change Refered
to IOUT = 125mA at +25°C)
GROUND PIN CURRENT, NOT ENABLED
vs TEMPERATURE
1µ
0.80
VENABLE = 0.5V
VIN = VOUT + 1V
0.40
100n
IOUT = 5mA
IOUT = 125mA
0.20
IGND (A)
Output Voltage Change (%)
0.60
0
–0.20
–0.40
IOUT = 250mA
10n
1n
–0.60
–0.80
–1.00
–50
–25
0
25
50
75
100
100p
–50
125
–25
0
750
700
725
VOUT = 5.0V
VOUT = 3.3V
400
VOUT = 2.5V
IGND (µA)
IGND (µA)
75
100
125
VOUT = 5V
IOUT = 250mA
700
500
300
50
GROUND PIN CURRENT vs TEMPERATURE
GROUND PIN CURRENT vs IOUT
800
600
25
Temperature (°C)
Temperature (°C)
675
VOUT = 3.3V
650
625
200
600
100
575
VOUT = 2.5V
550
0
0
25
50
75
100
125
150 175 200
–50
225 250
REG102
SBVS024F
–25
0
25
50
75
100
125
Temperature (°C)
IOUT (mA)
www.ti.com
5
TYPICAL CHARACTERISTICS (Cont.)
For all models, at TJ = +25°C and VENABLE = 1.8V, unless otherwise noted.
RIPPLE REJECTION vs FREQUENCY
RIPPLE REJECTION vs (VIN – VOUT)
80
30
IOUT = 2mA
25
IOUT = 2mA
COUT = 10µF
60
50
Ripple Rejection (dB)
Ripple Rejection (dB)
70
IOUT = 100mA
COUT = 10µF
IOUT = 100mA
40
30
20
COUT = 0µF
10
20
15
10
Frequency = 100kHz
COUT = 10µF
VOUT = 3.3V
IOUT = 100mA
5
0
0
10
100
1k
10k
100k
1M
10M
1.0
0.9
0.8
0.7
Frequency (Hz)
REG102-5.0
100
Noise Voltage (µVrms)
Noise Voltage (µVrms)
40
REG102-3.3
30
20
REG102-2.5
COUT = 0.01µF
10Hz < BW < 100kHz
0.1
0.1
0
REG102-3.3
80
70
60
50
REG102-2.5
40
COUT = 0µF
10Hz < BW < 100kHz
30
20
1
1
10
10
1
COUT = 1µF
COUT = 0µF
eN (µV/√Hz)
IOUT = 100mA
CNR = 0µF
IOUT = 100mA
CNR = 0.01µF
1
COUT = 1µF
0.1
COUT = 0µF
COUT = 10µF
0.01
COUT = 10µF
0.01
10
100
1k
10k
1k
NOISE SPECTRAL DENSITY
10
0.1
100
CNR (pF)
NOISE SPECTRAL DENSITY
eN (µV/√Hz)
0.2
REG102-5.0
90
COUT (µF)
10k
100k
10
Frequency (Hz)
6
0.3
110
50
10
0.4
RMS NOISE VOLTAGE vs CNR
RMS NOISE VOLTAGE vs COUT
0
0.5
VIN – VOUT (V)
60
10
0.6
100
1k
10k
100k
Frequency (Hz)
REG102
www.ti.com
SBVS024F
TYPICAL CHARACTERISTICS
(Cont.)
For all models, at TJ = +25°C and VENABLE = 1.8V, unless otherwise noted.
CURRENT LIMIT vs TEMPERATURE
CURRENT LIMIT FOLDBACK
3.5
450
3.0
400
VIN = VOUT + 1V
ICL = Current Limit
350
ICL
IOUT (mA)
2.0
1.5
1.0
300
250
ISC = Short-Circuit Current
200
ISC
0.5
150
0
100
150
200
250
300
350
400
100
–50
450
–25
0
25
50
100
Temperature (°C)
LOAD TRANSIENT RESPONSE
LINE TRANSIENT RESPONSE
REG102-3.3
VIN = 4.3V
COUT = 0µF
VOUT
COUT = 10µF
125
REG102-3.3
IOUT = 250mA
COUT = 0
VOUT
COUT = 10µF
VOUT
VOUT
IOUT
250mA
5.3V
VIN
4.3V
25mA
10µs/div
50µs/div
TURN-ON
TURN-OFF
1V/div
COUT = 10µF
RLOAD = 13Ω
REG102-3.3
VIN = VOUT + 1V
CNR = 0.01µF
VOUT
1V/div
COUT = 0µF
RLOAD = 13Ω
COUT = 10µF
RLOAD = 13Ω
COUT = 1.0µF
RLOAD = 13Ω
COUT = 0µF
RLOAD = 660Ω
VENABLE
1V/div
1V/div
COUT = 0µF
RLOAD = 660Ω
VOUT
VENABLE
REG102-3.3
250µs/div
200µs/div
REG102
SBVS024F
75
Output Current (mA)
50mV/div
50
200mV/div
200mV/div
0
50mV/div
Output Voltage (V)
REG102-3.3
2.5
www.ti.com
7
TYPICAL CHARACTERISTICS
(Cont.)
For all models, at TJ = +25°C and VENABLE = 1.8V, unless otherwise noted.
POWER UP/POWER DOWN
IENABLE vs VENABLE
10µ
VOUT = 3.0V
RLOAD = 12Ω
500mV/div
IENABLE (A)
1.0µ
100n
T = +25°C
T = +125°C
10n
T = –55°C
1n
6
7
8
9
1s/div
10
VENABLE (V)
ADJUST PIN CURRENT vs TEMPERATURE
RMS NOISE VOLTAGE vs CADJ
0.350
80
VOUT = 3.3V
0.300
COUT = 0.1µF
10Hz < frequency < 100kHz
70
0.250
IADJ (µA)
VN (rms)
60
50
40
0.150
0.100
30
0.050
0
20
10
200mV/div
0.200
100
1k
10k
100k
–50
25mA
8
25
50
75
100
LOAD TRANSIENT-ADJUSTABLE VERSION
LINE TRANSIENT-ADJUSTABLE VERSION
COUT = 0
VOUT
50mV/div
COUT = 10µF
COUT = 0
125
VOUT
COUT = 10µF
VOUT
VOUT
REG102–A
250mA
0
Temperature (°C)
50mV/div
200mV/div
–25
CADJ (pF)
VIN = 4.3V
5.3V
VOUT = 3.3V
IOUT
REG102–A
IOUT = 250mA
CFB = 0.01µF
VOUT = 3.3V
VIN
4.3V
REG102
www.ti.com
SBVS024F
BASIC OPERATION
The REG102 series of LDO (low dropout) linear regulators
offers a wide selection of fixed output voltage versions and
an adjustable output version as well. The REG102 belongs
to a family of new generation LDO regulators that use a
DMOS pass transistor to achieve ultra low-dropout performance and freedom from output capacitor constraints. Ground
pin current remains under 1mA over all line, load, and
temperature conditions. All versions have thermal and overcurrent protection, including foldback current limit.
The REG102 does not require an output capacitor for regulator
stability and is stable over most output currents and with almost
any value and type of output capacitor up to 10µF or more. For
applications where the regulator output current drops below
several milliamps, stability can be enhanced by adding a 1kΩ
to 2kΩ load resistor, using capacitance values smaller than
10µF, or keeping the effective series resistance greater than
0.05Ω including the capacitor ESR and parasitic resistance in
printed circuit board traces, solder joints, and sockets.
Enable
VIN
REG102
In
GND
0.1µF
VOUT
Out
NR
COUT
CNR
0.01µF
Optional
FIGURE 1. Fixed Voltage Nominal Circuit for the REG102.
the regulator from damage under all load conditions. A
characteristic of VOUT versus IOUT is given in Figure 3 and in
the Typical Characteristics section.
Although an input capacitor is not required, it is a good
standard analog design practice to connect a 0.1µF low ESR
capacitor across the input supply voltage. This is recommended to counteract reactive input sources and improve
ripple rejection by reducing input voltage ripple.
CURRENT LIMIT FOLDBACK
3.5
3
Output Voltage (V)
REG102-3.3
Figure 1 shows the basic circuit connections for the fixed
voltage models. Figure 2 gives the connections for the adjustable output version (REG102A) and example resistor values for
some commonly used output voltages. Values for other voltages can be calculated from the equation shown in Figure 2.
2.5
ICL
2
1.5
1
ISC
0.5
0
INTERNAL CURRENT LIMIT
0
The REG102 internal current limit has a typical value of
400mA. A foldback feature limits the short-circuit current to a
typical short-circuit value of 150mA, which helps to protect
50
100
150
200
250
300
350
400
450
Output Current (mA)
FIGURE 3. Foldback Current Limit of the REG102-3.3 at 25°C.
Enable
5
2
VIN
VOUT
1
REG102
4
0.1µF
IADJ
3 Gnd
R1
CFB
0.01µF
COUT
EXAMPLE RESISTOR VALUES
VOUT (V)
R1 (Ω)(1)
R2 (Ω)(1)
2.5
11.3k
1.13k
11.5k
1.15k
3.0
15.8k
1.58k
11.5k
1.15k
3.3
18.7k
1.87k
11.5k
1.15k
5.0
34.0k
3.40k
11.5k
1.15k
Load
Adj
R2
Optional
NOTE: (1) Resistors are standard 1% values.
Pin numbers for the SOT-223 package.
VOUT = (1 + R1/R2) • 1.26V
To reduce current through divider, increase resistor
values (see table at right).
As the impedance of the resistor divider increases,
IADJ (~200nA) may introduce an error.
CFB improves noise and transient response.
FIGURE 2. Adjustable Voltage Circuit for the REG102A.
REG102
SBVS024F
www.ti.com
9
ENABLE
OUTPUT NOISE
A precision bandgap reference is used to generate the
internal reference voltage, VREF. This reference is the dominant noise source within the REG102 and generates approximately 29µVrms in the 10Hz to 100kHz bandwidth at the
reference output. The regulator control loop gains up the
reference noise, so that the noise voltage of the regulator is
approximately given by:
VN = 29µVrms
V
R1 + R2
= 29µVrms • OUT
R2
VREF
(1)
As the value of VREF is 1.26V, this relationship reduces to:
VN = 23
µVrms
• VOUT
V
(2)
Connecting a capacitor, CNR, from the Noise Reduction (NR)
pin to ground forms a low-pass filter for the voltage reference. Adding CNR (as shown in Figure 4) forms a low-pass
filter for the voltage reference. For CNR = 10nF, the total noise
in the 10Hz to 100kHz bandwidth is reduced by approximately a factor of 2.8 for VOUT = 3.3V. This noise reduction
effect is shown in Figure 5 and as RMS Noise Voltage vs CNR
in the Typical Characteristics section.
RMS NOISE VOLTAGE vs CNR
110
100
Noise Voltage (Vrms)
The Enable pin is active high and compatible with standard
TTL-CMOS levels. Inputs below 0.5V (max) turn the regulator off and all circuitry is disabled. Under this condition,
ground pin current drops to approximately 10nA. When not
used, the Enable pin can be connected to VIN. When a pullup resistor is used, and operation below 1.8V is required, use
pull-up resistor values below 50kΩ.
90
REG102-5.0
80
REG102-3.3
70
60
REG102-2.5
50
40
COUT = 0µF
10Hz < BW < 100kHz
30
20
0.1
10
100
1k
10k
CNR (pF)
FIGURE 5. Output Noise versus Noise Reduction Capacitor.
Noise can be further reduced by carefully choosing an output
capacitor, COUT. Best overall noise performance is achieved
with very low (< 0.22µF) or very high (> 2.2µF) values of COUT
(see the RMS Noise Voltage vs COUT typical characteristic).
The REG102 uses an internal charge pump to develop an
internal supply voltage sufficient to drive the gate of the
DMOS pass element above VIN. The charge-pump switching
noise (nominal switching frequency = 2MHz) is not measurable at the output of the regulator over most values of IOUT
and COUT.
The REG102 adjustable version does not have the noisereduction pin available; however, the adjust pin is the summing junction of the error amplifier. A capacitor, CFB, connected from the output to the adjust pin can reduce both the
output noise and the peak error from a load transient (see the
typical characteristics for output noise performance).
VIN
NR
(fixed output
versions only)
Low-Noise
Charge Pump
CNR
(optional)
VREF
(1.26V)
DMOS
Output
VOUT
Over-Current
Over Temp
Protection
Enable
R1
R2
Adj
(adjustable
versions)
REG102
NOTE: R1 and R2 are internal
on fixed output versions.
FIGURE 4. Block Diagram.
10
REG102
www.ti.com
SBVS024F
DROPOUT VOLTAGE
The REG102 uses an N-channel DMOS as the pass element.
When (VIN – VOUT) is less than the drop-out voltage (VDROP),
the DMOS pass device behaves like a resistor; therefore, for
low values of (VIN – VOUT), the regulator input-to-output
resistance is the RdsON of the DMOS pass element (typically
600mΩ). For static (DC) loads, the REG102 typically maintains regulation down to a (VIN – VOUT) voltage drop of 150mV
at full rated output current. In Figure 6, the bottom line (DC
dropout) shows the minimum VIN to VOUT voltage drop required to prevent dropout under DC load conditions.
For large step changes in load current, the REG102 requires
a larger voltage drop across it to avoid degraded transient
response. The boundary of this transient drop-out region is
shown as the top line in Figure 6 and values of VIN to VOUT
voltage drop above this line insure normal transient response.
DROPOUT VOLTAGE vs IOUT
350
Dropout Voltage (mV)
300
250
0mA to IOUT Transient
200
150
DC
100
50
0
0
50
100
150
200
250
IOUT (mA)
FIGURE 6. Transient and DC Dropout.
In the transient dropout region between DC and Transient,
transient response recovery time increases. The time required
to recover from a load transient is a function of both the
magnitude and rate of the step change in load current and the
available headroom VIN to VOUT voltage drop. Under worst-
case conditions (full-scale load change with (VIN – VOUT)
voltage drop close to DC dropout levels), the REG102 can
take several hundred microseconds to re-enter the specified
window of regulation.
TRANSIENT RESPONSE
The REG102 response to transient line and load conditions
improves at lower output voltages. The addition of a capacitor
(nominal value 0.47µF) from the output pin to ground can
improve the transient response. In the adjustable version, the
addition of a capacitor, CFB (nominal value 10nF), from the
output to the adjust pin can also improve the transient
response.
THERMAL PROTECTION
Power dissipated within the REG102 can cause the junction
temperature to rise. The REG102 has thermal shutdown
circuitry that protects the regulator from damage which disables the output when the junction temperature reaches
approximately 160°C, allowing the device to cool. When the
junction temperature cools to approximately 140°C, the output circuitry is again enabled. Depending on various conditions, the thermal protection circuit can cycle on and off. This
limits the dissipation of the regulator, but can have an
undesirable effect on the load.
Any tendency to activate the thermal protection circuit indicates excessive power dissipation or an inadequate heat
sink. For reliable operation, junction temperature must be
limited to 125°C, maximum. To estimate the margin of safety
in a complete design (including heat sink), increase the
ambient temperature until the thermal protection is triggered;
use worst-case loads and signal conditions. For good reliability, thermal protection should trigger more than 35°C above
the maximum expected ambient condition of the application.
This produces a worst-case junction temperature of 125°C at
the highest expected ambient temperature and worst-case
load.
The internal protection circuitry of the REG102 is designed to
protect against overload conditions and is not intended to
replace proper heat sinking. Continuously running the REG102
into thermal shutdown will degrade reliability.
REG102
SBVS024F
www.ti.com
11
PD = (VIN – VOUT ) • IOUT
POWER DISSIPATION
The REG102 is available in three different package configurations. The ability to remove heat from the die is different for
each package type and, therefore, presents different considerations in the printed circuit board (PCB) layout. The PCB
area around the device that is free of other components
moves the heat from the device to the ambient air. Although
it is difficult to impossible to quantify all of the variables in a
thermal design of this type, performance data for several
simplified configurations are shown in Figure 7. In all cases,
the PCB copper area is bare copper (free of solder resist
mask), not solder plated, and are for 1-ounce copper. Using
heavier copper will increase the effectiveness in moving the
heat from the device. In those examples where there is
copper on both sides of the PCB, no connection has been
provided between the two sides. The addition of plated
through holes will improve the heat sink effectiveness.
Power dissipation depends on input voltage, load conditions,
and duty cycle and is equal to the product of the average
output current times the voltage across the output element,
VIN to VOUT voltage drop.
(3)
Power dissipation can be minimized by using the lowest
possible input voltage necessary to assure the required
output voltage.
REGULATOR MOUNTING
The tab of the SOT-223 package is electrically connected to
ground. For best thermal performance, this tab must be
soldered directly to a circuit-board copper area. Increasing
the copper area improves heat dissipation, as shown in
Figure 8.
Although the tab of the SOT-223 is electrical ground, it is not
intended to carry current. The copper pad that acts as a heat
sink should be isolated from the rest of the circuit to prevent
current flow through the device from the tab to the ground
pin. Solder pad footprint recommendations for the various
REG102 devices are presented in Application Bulletin Solder
Pad Recommendations for Surface-Mount Devices
(SBFA015), available from the Texas Instruments web site
(www.ti.com).
DEVICE DISSIPATION vs TEMPERATURE
Power Dissipation (Watts)
2.5
CONDITIONS
#1
#2
#3
#4
2
CONDITION
PACKAGE
PCB AREA
θJA
1
2
3
4
SOT-223
SOT-223
SO-8
SOT-23
4in2 Top Side Only
0.5in2 Top Side Only
—
—
53°C/W
110°C/W
150°C/W
200°C/W
1.5
1
0.5
0
0
25
50
75
100
125
Ambient Temperature (°C)
FIGURE 7. Maximum Power Dissipation versus Ambient Temperature for the Various Packages and PCB Heat Sink Configurations.
THERMAL RESISTANCE vs PCB COPPER AREA
Thermal Resistance, θJA (°C/W)
180
Circuit-Board Copper Area
REG102
Surface-Mount Package
1 oz. copper
160
140
120
100
80
60
40
20
REG102
SOT-223 Surface-Mount Package
0
0
1
2
3
4
5
Copper Area (inches2)
FIGURE 8. Thermal Resistance versus PCB Area for the Five-Lead SOT-223.
12
REG102
www.ti.com
SBVS024F
PACKAGE OPTION ADDENDUM
www.ti.com
7-May-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
REG102GA-2.5
ACTIVE
SOT-223
DCQ
6
REG102GA-2.5/2K5
ACTIVE
SOT-223
DCQ
REG102GA-2.5/2K5G4
ACTIVE
SOT-223
REG102GA-2.5G4
ACTIVE
REG102GA-2.8
78
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-2.8/2K5
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-2.8/2K5G4
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-2.85
ACTIVE
SOT-223
DCQ
6
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-2.85/2K5
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-2.85G4
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-2.8G4
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-3
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-3.3
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-3.3/2K5
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-3.3/2K5G4
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-3.3G4
ACTIVE
SOT-223
DCQ
6
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-3/2K5
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-3/2K5G4
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-3G4
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-5
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-5/2K5
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-5/2K5G4
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-5G4
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-A
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102GA-A/2K5
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
78
78
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
7-May-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
REG102GA-A/2K5G4
ACTIVE
SOT-223
DCQ
6
REG102GA-AG4
ACTIVE
SOT-223
DCQ
6
REG102GA2.85/2K5G4
ACTIVE
SOT-223
DCQ
REG102NA-2.5/250
ACTIVE
SOT-23
REG102NA-2.5/250G4
ACTIVE
REG102NA-2.5/3K
2500 Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
CU NIPDAU
Level-2-260C-1 YEAR
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-2.5/3KG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-2.8/250
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-2.8/250G4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-2.8/3K
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-2.8/3KG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-2.85/250
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-2.85/3K
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-2.85/3KG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-285/250G4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-3.3/250
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-3.3/250G4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-3.3/3K
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-3.3/3KG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-3/250
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-3/250G4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-3/3K
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-3/3KG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-5/250
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-5/250G4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-5/3K
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
78
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
7-May-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
REG102NA-5/3KG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-A/250
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-A/250G4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-A/3K
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102NA-A/3KG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
REG102UA-2.5
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-2.5/2K5
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-2.5/2K5G4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-2.5G4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-2.8
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-2.8/2K5
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-2.8/2K5G4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-2.85
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-2.85/2K5
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-2.85G4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-2.8G4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-3
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-3.3
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-3.3/2K5
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-3.3/2K5G4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-3.3G4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-3/2K5
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-3/2K5G4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-3G4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-5
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-5/2K5
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Addendum-Page 3
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
7-May-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
REG102UA-5/2K5G4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-5G4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-A
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-A/2K5
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-A/2K5G4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA-AG4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
REG102UA2.85/2K5G4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
7-May-2007
TAPE AND REEL INFORMATION
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
Device
7-May-2007
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
REG102NA-2.5/250
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-2.5/3K
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-2.8/250
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-2.8/3K
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-2.85/250
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-2.85/3K
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-3.3/250
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-3.3/3K
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-3/250
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-3/3K
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-5/250
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-5/3K
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-A/250
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
REG102NA-A/3K
DBV
5
NSE
177
8
3.2
3.2
1.4
4
8
NONE
TAPE AND REEL BOX INFORMATION
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
REG102NA-2.5/250
DBV
5
NSE
195.0
200.0
45.0
REG102NA-2.5/3K
DBV
5
NSE
195.0
200.0
45.0
REG102NA-2.8/250
DBV
5
NSE
195.0
200.0
45.0
REG102NA-2.8/3K
DBV
5
NSE
195.0
200.0
45.0
REG102NA-2.85/250
DBV
5
NSE
195.0
200.0
45.0
REG102NA-2.85/3K
DBV
5
NSE
195.0
200.0
45.0
REG102NA-3.3/250
DBV
5
NSE
195.0
200.0
45.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
7-May-2007
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
REG102NA-3.3/3K
DBV
5
NSE
195.0
200.0
45.0
REG102NA-3/250
DBV
5
NSE
195.0
200.0
45.0
REG102NA-3/3K
DBV
5
NSE
195.0
200.0
45.0
REG102NA-5/250
DBV
5
NSE
195.0
200.0
45.0
REG102NA-5/3K
DBV
5
NSE
195.0
200.0
45.0
REG102NA-A/250
DBV
5
NSE
195.0
200.0
45.0
REG102NA-A/3K
DBV
5
NSE
195.0
200.0
45.0
Pack Materials-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power
Wireless
www.ti.com/lpw
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated