Features ● ● ● ● ● ● ● ● ● 2:1 Wide Input Voltage Range 10 Watts Output Power 1.6kVDC Isolation Fixed Operating Frequency Six-Sided Continuous Shield International Safety Standard Approvals UL 1950 Component Recognized Standard 50.8 x25.4x10.2mm Package Efficiency to 86% Selection Guide 12V, 24V and 48V Input Types Part Number Output Current mA Input (4) Current mA Efficiency(5) Capacitive(6) Load max. µF Input Range VDC Output Voltage VDC RP10-123.3SE 9-18 3.3 2000 724 80 6800 RP10-1205SE 9-18 5 2000 1082 81 4700 RP10-1212SE 9-18 12 830 1064 82 690 RP10-1215SE 9-18 15 670 1088 81 470 RP10-243.3SE 18-36 3.3 2000 362 80 6800 RP10-2405SE 18-36 5 2000 534 82 4700 RP10-2412SE 18-36 12 830 519 84 690 RP10-2415SE 18-36 15 670 523 84 470 RP10-483.3SE 36-75 3.3 2000 183 79 6800 RP10-4805SE 36-75 5 2000 260 84 4700 RP10-4812SE 36-75 12 830 253 86 690 RP10-4815SE 36-75 15 670 258 85 470 RP10-1205DE 9-18 ±5 ±1000 1068 82 ±680 RP10-1212DE 9-18 ±12 ±416 1053 83 ±330 RP10-1215DE 9-18 ±15 ±333 1041 84 ±110 RP10-2405DE 18-36 ±5 ±1000 548 80 ±680 RP10-2412DE 18-36 ±12 ±416 520 84 ±330 RP10-2415DE 18-36 ±15 ±333 520 84 ±110 RP10-4805DE 36-75 ±5 ±1000 267 82 ±680 RP10-4812DE 36-75 ±12 ±416 254 86 ±330 RP10-4815DE 36-75 ±15 ±333 260 84 ±110 % POWERLINE DC/DC-Converter RP10S_DE Series 10 Watt 2” x 1” Package Single & Dual Output Description The E-Series of DC/DC Converters are fully certified to EN 60950: 2000. This makes them ideal for all Telecom and safety applications where approved isolation is required. They also meet UL 1950 and CSA 950 standards (9). 206 April-2005 www.recom-international.com POWERLINE RP10-S_DE Series DC/DC-Converter Derating-Graph (Ambient Temperature) 125 RP10-2405SE 100 100 76 75 Natural Convection 50 Output Power (%) Output Power (%) 67 RP10-2405SE With Heat Sink 125 25 0 -25 -10 0 50 60 70 Ambient Temperature Range (°C) 80 90 100 79 75 Natural Convection 50 25 0 -25 125 100 75 Natural Convection 50 Output Power (%) Output Power (%) 100 86 75 25 0 -25 -10 0 50 60 70 Ambient Temperature Range (°C) 80 90 100 79 25 0 -25 100 75 75 Natural Convection Output Power (%) Output Power (%) 100 25 -10 0 50 60 70 Ambient Temperature Range (°C) 80 90 100 50 0 -40 -25 -10 0 100 100 Output Power (%) Output Power (%) 75 Natural Convection 25 Ambient Temperature Range (°C) 80 90 100 85 RP10-2405SE_DE/M1 With Heat Sink 125 50 60 70 50 60 70 Ambient Temperature Range (°C) RP10-4805SE/M1 0 -40 -25 -10 0 Natural Convection 25 125 50 50 60 70 80 90 100 83 RP10-2405SE_DE/M1 125 0 -25 -10 0 Ambient Temperature Range (°C) RP10-4805SE 50 Natural Convection 50 125 75 50 60 70 80 90 100 81 RP10-2405DE With Heat Sink RP10-2405DE 125 67 -10 0 Ambient Temperature Range (°C) 80 90 100 85 50 Natural Convection 25 0 -40 -25 -10 0 50 60 70 Ambient Temperature Range (°C) 80 90 100 88 Derating graphes are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical customer service at [email protected] www.recom-international.com April-2005 207 RP10-S_DE Series POWERLINE DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range 12V nominal input 24V nominal input 48V nominal input Input Filter Input Surge Voltage (100 ms max.) 9-18VDC 18-36VDC 36-75VDC Pi Type 12V Input 24V Input 48V Input 36VDC 50VDC 100VDC Input Reflected Ripple (nominal Vin and full load) 30mAp-p Start Up Time (nominal Vin and constant resistor load) 20ms typ. Remote ON/OFF (see note 8) (Positive logic) DC-DC ON DC-DC OFF Short or 0V < Vr < 1.2V (Negative logic) DC-DC ON Short or 0V < Vr < 1.2V DC-DC OFF Open or 3.5V < Vr < 12V Remote OFF input current Nominal input Output Power ±2% Minimum Load (see Note 1) 10% of FL Line Regulation (LL-HL at full load) ±1% Single Dual Cross Regulation (asymmetrical load 25%/100% FL) Ripple and Noise (20MHz bandwith) ±1% ±2% ±5% Single 50mVp-p Dual 75mVp-p Temperature Coefficient ±0.02%/°C, max. Transient Response (25% load step change) Over Voltage Protection Zener diode clamp 2.5mA 10W max. Output Voltage Accuracy (full Load and nominal Vin) Load Regulation (25% to 100% FL) Open or 3.5V < Vr < 12V 500µS 3.3V output 5V output 12V output 15V output Over Load Protection (% of full load at nominal Vin) 3.9V 6.2V 15V 18V 150% typ Short Circuit Protection Hiccup, automatic recovery Efficiency see „Selection Guide“ table Isolation Voltage 1.600VDC min. Isolation Resistance 109 Ω min. Isolation Capacitance 300pF max. Operating Frequency 300kHz typ. Approved to Safety Standards UL 1950, EN60950 Operating Temperature Range Standard -25°C to +85°C(with derating) (Reference Derating Curve) M1 -40°C to +85°C(non derating) Maximum Case Temperature +100°C Storage Temperature Range -55°C to +105°C continued on next page 208 April-2005 www.recom-international.com RP10-S_DE Series POWERLINE DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Thermal Impedance Natural convection 12°C/Watt Natural convection with Heat Sink 10°C/Watt Thermal Shock MIL-STD-810D Vibration 10-55Hz, 2G, 30 Min. along X, Y and Z Relative Humidity 5% to 95% RH Case Material Nickel-Coated copper Base Material Non-conductive black plastic Potting Material Conducted Emissions Radiated Emissions ESD Radiated Immunity Fast Transient Surge Conducted Immunity Epoxy (UL94-V0) EN55022 EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Weight Level A Level A Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 27g Dimensions 50.8 x 25.4 x 10.2mm 1.976 x 106 Hours MTBF (see note 2) Notes : 1. The RP10 (W) series required a minimum 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listedspecification. 2. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC. (Ground fixed and controlled environment). 3. Simulated source impedance of 12uH. 12uH inductor in series with +Vin. 4. Maximum value at nominal input voltage and full load of standard type. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistor load. 7. The ON/OFF control function can be positive or negative logic. The pin voltage is referenced to negative input. Positive logic ON/OFF is standard, no suffix (Ex. RP10-2405SE) Negative logic ON/OFF is marked with suffix-N (Ex. RP10-2405SE/N). 8. Heat sink is optional and P/N: 7G-0020A. 9. The M1 version (RP10-xxxxSE/M1, RP10-xxxxDE/M1) does not carry the UL certification. 10.M1 version is more efficient, therefore, it can be operated in a more extensive temperature range than standard version. 11. See application notes for EMI-filtering. www.recom-international.com April-2005 209 RP10-S_DE Series POWERLINE DC/DC-Converter Package Style and Pinning (mm) 3rd angle projection 50.80 25.40 10.20 dia. 1.0 5.6 2.50 5.10 20.30 15.20 Pin Connections 3 1 2 6 210 Bottom View 10.20 4 10.20 5 12.70 Pin # 1 2 3 4 5 6 Single +Vin -Vin +Vout No Pin -Vout CTRL Dual +Vin -Vin +Vout Com -Vout CTRL Pin Pitch Tolerance ±0.35 mm April-2005 www.recom-international.com