SPANSION S29AL008D70TFN023

This document has not been approved. Sharing this document with non-Spansion employees violates QS9000/TS16949 requirements.
S29AL008D
8 Megabit (1 M x 8-Bit/512 K x 16-Bit)
CMOS 3.0 Volt-only Boot Sector Flash Memory
Data Sheet
Distinctive Characteristics
Architectural Advantage
Performance Characteristics
„ Single power supply operation
„ High performance
— 2.7 to 3.6 volt read and write operations for batterypowered applications
„ Manufactured on 200nm process technology
— Compatible with 0.32 µm and 230nm Am29LV160
devices
— Access times as fast as 55 ns
— Extended temperature range (-40°C to +125°C)
„ Ultra low power consumption (typical values
at 5 MHz)
— 200 nA Automatic Sleep mode current
„ Flexible sector architecture
— 200 nA standby mode current
— One 16 Kbyte, two 8 Kbyte, one 32 Kbyte, and fifteen
64 Kbyte sectors (byte mode)
— One 8 Kword, two 4 Kword, one 16 Kword, and fifteen
32 Kword sectors (word mode)
— Supports full chip erase
— Sector Protection features:
— A hardware method of locking a sector to prevent
any program or erase operations within that sector
— Sectors can be locked in-system or via programming
equipment
— Temporary Sector Unprotect feature allows code
changes in previously locked sectors
„ Unlock Bypass Program Command
— Reduces overall programming time when issuing
multiple program command sequences
— 15 mA program/erase current
„ Cycling endurance: 1,000,000 cycles per
sector typical
„ Data retention: 20 years typical
— Reliable operation for the life of the system
Package option
„ 48-ball FBGA
„ 48-pin TSOP
„ 44-pin SO
Software Features
„ Data# Polling and toggle bits
„ Top or bottom boot block configurations
available
— Provides a software method of detecting program or
erase operation completion
„ Embedded Algorithms
„ Erase Suspend/Erase Resume
— Embedded Erase algorithm automatically
preprograms and erases the entire chip or any
combination of designated sectors
— Embedded Program algorithm automatically writes
and verifies data at specified addresses
„ Compatibility with JEDEC standards
— Pinout and software compatible with single-power
supply Flash
— Superior inadvertent write protection
— 7 mA read current
— Suspends an erase operation to read data from, or
program data to, a sector that is not being erased,
then resumes the erase operation
Hardware Features
„ Ready/Busy# pin (RY/BY#)
— Provides a hardware method of detecting program or
erase cycle completion
„ Hardware reset pin (RESET#)
— Hardware method to reset the device to reading array
data
Publication Number S29AL008D_00
Revision A
Amendment 3
Issue Date June 16, 2005
“This document states the current technical specifications regarding the Spansion product(s) described herein. Spansion LLC deems the products
to have been in sufficient production volume such that subsequent versions of this document are not expected to change. However, typographical
or specification corrections, or modifications to the valid combinations offered may occur.”
D a t a
S h e e t
Notice On Data Sheet Designations
Spansion LLC issues data sheets with Advance Information or Preliminary designations to advise
readers of product information or intended specifications throughout the product life cycle, including development, qualification, initial production, and full production. In all cases, however,
readers are encouraged to verify that they have the latest information before finalizing their design. The following descriptions of Spansion data sheet designations are presented here to highlight their presence and definitions.
Advance Information
The Advance Information designation indicates that Spansion LLC is developing one or more specific products, but has not committed any design to production. Information presented in a document with this designation is likely to change, and in some cases, development on the product
may discontinue. Spansion LLC therefore places the following conditions upon Advance Information content:
“This document contains information on one or more products under development at Spansion LLC. The
information is intended to help you evaluate this product. Do not design in this product without contacting the factory. Spansion LLC reserves the right to change or discontinue work on this proposed
product without notice.”
Preliminary
The Preliminary designation indicates that the product development has progressed such that a
commitment to production has taken place. This designation covers several aspects of the product life cycle, including product qualification, initial production, and the subsequent phases in the
manufacturing process that occur before full production is achieved. Changes to the technical
specifications presented in a Preliminary document should be expected while keeping these aspects of production under consideration. Spansion places the following conditions upon Preliminary content:
“This document states the current technical specifications regarding the Spansion product(s) described
herein. The Preliminary status of this document indicates that product qualification has been completed,
and that initial production has begun. Due to the phases of the manufacturing process that require
maintaining efficiency and quality, this document may be revised by subsequent versions or modifications due to changes in technical specifications.”
Combination
Some data sheets will contain a combination of products with different designations (Advance Information, Preliminary, or Full Production). This type of document will distinguish these products
and their designations wherever necessary, typically on the first page, the ordering information
page, and pages with DC Characteristics table and AC Erase and Program table (in the table
notes). The disclaimer on the first page refers the reader to the notice on this page.
Full Production (No Designation on Document)
When a product has been in production for a period of time such that no changes or only nominal
changes are expected, the Preliminary designation is removed from the data sheet. Nominal
changes may include those affecting the number of ordering part numbers available, such as the
addition or deletion of a speed option, temperature range, package type, or VIO range. Changes
may also include those needed to clarify a description or to correct a typographical error or incorrect specification. Spansion LLC applies the following conditions to documents in this category:
“This document states the current technical specifications regarding the Spansion product(s) described
herein. Spansion LLC deems the products to have been in sufficient production volume such that subsequent versions of this document are not expected to change. However, typographical or specification
corrections, or modifications to the valid combinations offered may occur.”
Questions regarding these document designations may be directed to your local AMD or Fujitsu
sales office.
2
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
General Description
The S29AL008D is an 8 Mbit, 3.0 volt-only Flash memory organized as 1,048,576
bytes or 524,288 words. The device is offered in 48-ball FBGA, 44-pin SO, and
48-pin TSOP packages. For more information, refer to publication number 21536.
The word-wide data (x16) appears on DQ15–DQ0; the byte-wide (x8) data appears on DQ7–DQ0. This device requires only a single, 3.0 volt VCC supply to
perform read, program, and erase operations. A standard EPROM programmer
can also be used to program and erase the device.
This device is manufactured using Spansion’s 200nm process technology, and offers all the features and benefits of the Am29LV800B, which was manufactured
using 0.32 µm process technology.
The standard device offers access times of 70, 90, and 120 ns, allowing high
speed microprocessors to operate without wait states. To eliminate bus contention the device contains separate chip enable (CE#), write enable (WE#) and
output enable (OE#) controls.
The device requires only a single 3.0 volt power supply for both read and write
functions. Internally generated and regulated voltages are provided for the program and erase operations.
The device is entirely command set compatible with the JEDEC single-powersupply Flash standard. Commands are written to the command register using
standard microprocessor write timings. Register contents serve as input to an internal state-machine that controls the erase and programming circuitry. Write
cycles also internally latch addresses and data needed for the programming and
erase operations. Reading data out of the device is similar to reading from other
Flash or EPROM devices.
Device programming occurs by executing the program command sequence. This
initiates the Embedded Program algorithm—an internal algorithm that automatically times the program pulse widths and verifies proper cell margin. The
Unlock Bypass mode facilitates faster programming times by requiring only two
write cycles to program data instead of four.
Device erasure occurs by executing the erase command sequence. This initiates
the Embedded Erase algorithm—an internal algorithm that automatically
preprograms the array (if it is not already programmed) before executing the
erase operation. During erase, the device automatically times the erase pulse
widths and verifies proper cell margin.
The host system can detect whether a program or erase operation is complete by
observing the RY/BY# pin, or by reading the DQ7 (Data# Polling) and DQ6 (toggle) status bits. After a program or erase cycle is completed, the device is ready
to read array data or accept another command.
The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other sectors. The device is fully
erased when shipped from the factory.
Hardware data protection measures include a low VCC detector that automatically inhibits write operations during power transitions. The hardware sector
protection feature disables both program and erase operations in any combination of the sectors of memory. This can be achieved in-system or via
programming equipment.
June 16, 2005 S29AL008D_00A3
S29AL008D
3
D a t a
S h e e t
The Erase Suspend feature enables the user to put erase on hold for any period
of time to read data from, or program data to, any sector that is not selected for
erasure. True background erase can thus be achieved.
The hardware RESET# pin terminates any operation in progress and resets the
internal state machine to reading array data. The RESET# pin may be tied to the
system reset circuitry. A system reset would thus also reset the device, enabling
the system microprocessor to read the boot-up firmware from the Flash memory.
The device offers two power-saving features. When addresses are stable for a
specified amount of time, the device enters the automatic sleep mode. The
system can also place the device into the standby mode. Power consumption is
greatly reduced in both these modes.
Spansion’s Flash technology combines years of Flash memory manufacturing experience to produce the highest levels of quality, reliability and cost
effectiveness. The device electrically erases all bits within a sector simultaneously via Fowler-Nordheim tunneling. The data is programmed using hot
electron injection.
4
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Table Of Contents
Product Selector Guide. . . . . . . . . . . . . . . . . . . . . . 6
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . 7
Special Handling Instructions for FBGA Package . . . . . . . . . . . . . . . . . 8
Pin Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Ordering Information . . . . . . . . . . . . . . . . . . . . . . 10
Standard Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
DQ3: Sector Erase Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 6. Toggle Bit Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 6. Write Operation Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . 33
Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 7. Maximum Negative Overshoot Waveform . . . . . . . . . . . . . . . 33
Figure 8. Maximum Positive Overshoot Waveform . . . . . . . . . . . . . . . . 33
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 9. ICC1 Current vs. Time (Showing Active and
Automatic Sleep Currents). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 10. Typical ICC1 vs. Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Device Bus Operations . . . . . . . . . . . . . . . . . . . . . . 11
Table 1. S29AL008D Device Bus Operations . . . . . . . . . . . . . . . . . . . . . .11
Word/Byte Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Requirements for Reading Array Data . . . . . . . . . . . . . . . . . . . . . . . . . 11
Writing Commands/Command Sequences . . . . . . . . . . . . . . . . . . . . . 12
Program and Erase Operation Status . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Automatic Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
RESET#: Hardware Reset Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Output Disable Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 2. S29AL008D Top Boot Block Sector Addresses . . . . . . . . . . . 14
Table 3. S29AL008D Bottom Boot Block Sector Addresses . . . . . . . . 15
Autoselect Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 4. S29AL008D Autoselect Codes (High Voltage Method) . . . . . 16
Sector Protection/Unprotection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Temporary Sector Unprotect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 1. Temporary Sector Unprotect Operation . . . . . . . . . . . . . . . . . 17
Figure 2. In-System Sector Protect/Sector Unprotect Algorithms. . . . . 18
Hardware Data Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Command Definitions . . . . . . . . . . . . . . . . . . . . . . 19
Reading Array Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Reset Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Autoselect Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Word/Byte Program Command Sequence . . . . . . . . . . . . . . . . . . . . . 20
Figure 3. Program Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Chip Erase Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Sector Erase Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Erase Suspend/Erase Resume Commands . . . . . . . . . . . . . . . . . . . . . 23
Figure 4. Erase Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 5. S29AL008D Command Definitions . . . . . . . . . . . . . . . . . . . . . . 25
Write Operation Status . . . . . . . . . . . . . . . . . . . . 27
DQ7: Data# Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5. Data# Polling Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RY/BY#: Ready/Busy# . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DQ6: Toggle Bit I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DQ2: Toggle Bit II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reading Toggle Bits DQ6/DQ2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DQ5: Exceeded Timing Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
June 16, 2005 S29AL008D_00A3
27
28
28
29
29
30
30
Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 11. Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Table 7. Test Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Key to Switching Waveforms . . . . . . . . . . . . . . . . 37
Figure 12. Input Waveforms and Measurement Levels . . . . . . . . . . . . . . 37
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 8. Read Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 13. Read Operations Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 9. Hardware Reset (RESET#) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 14. RESET# Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Table 10. Word/Byte Configuration (BYTE#) . . . . . . . . . . . . . . . . . . . . 40
Figure 15. BYTE# Timings for Read Operations . . . . . . . . . . . . . . . . . . . 41
Figure 16. BYTE# Timings for Write Operations . . . . . . . . . . . . . . . . . . 41
Erase / Program Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 17. Program Operation Timings . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 18. Chip/Sector Erase Operation Timings . . . . . . . . . . . . . . . . . 44
Figure 19. Data# Polling Timings (During Embedded Algorithms) . . . . 45
Figure 20. Toggle Bit Timings (During Embedded Algorithms) . . . . . . 45
Figure 21. DQ2 vs. DQ6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 11. Temporary Sector Unprotect . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 22. Temporary Sector Unprotect Timing Diagram . . . . . . . . . . 46
Figure 23. Sector Protect/Unprotect Timing Diagram . . . . . . . . . . . . . 47
Table 12. Alternate CE# Controlled Erase/Program Operations . . . . . 48
Figure 24. Alternate CE# Controlled Write Operation Timings. . . . . 49
Erase and Programming Performance. . . . . . . . . 49
Table 13. Latchup Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table 14. TSOP, SO, and BGA Pin Capacitance . . . . . . . . . . . . . . . . . . . 50
Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 51
TS 048—48-Pin Standard TSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
VBK 048 - 48 Ball Fine-Pitch Ball Grid Array (FBGA)
8.15 x 6.15 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
SO 044—44-Pin Small Outline Package . . . . . . . . . . . . . . . . . . . . . . .53
Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . . 54
S29AL008D
5
D a t a
S h e e t
Product Selector Guide
Family Part Number
Speed Options
S29AL008D
Full Voltage Range: VCC = 2.7 – 3.6 V
Regulated Voltage Range: VCC = 3.0 – 3.6V
70
90
55
Max access time, ns (tACC)
55
70
90
Max CE# access time, ns (tCE)
55
70
90
Max OE# access time, ns (tOE)
30
30
35
Note: See AC Characteristics, on page 38 for full specifications.
Block Diagram
DQ0–DQ15 (A-1)
RY/BY#
VCC
Sector Switches
VSS
Erase Voltage
Generator
RESET#
WE#
BYTE#
Input/Output
Buffers
State
Control
Command
Register
PGM Voltage
Generator
Chip Enable
Output Enable
Logic
CE#
OE#
VCC Detector
Address Latch
STB
Timer
A0–A18
6
S29AL008D
STB
Data
Latch
Y-Decoder
Y-Gating
X-Decoder
Cell Matrix
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Connection Diagrams
A15
A14
A13
A12
A11
A10
A9
A8
NC
NC
WE#
RESET#
NC
NC
RY/BY#
A18
A17
A7
A6
A5
A4
A3
A2
A1
June 16, 2005 S29AL008D_00A3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Standard TSOP
S29AL008D
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
A16
BYTE#
VSS
DQ15/A-1
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
VSS
CE#
A0
7
D a t a
S h e e t
Connection Diagrams
RY/BY#
A18
A17
A7
A6
A5
A4
A3
A2
A1
A0
CE#
VSS
OE#
DQ0
DQ8
DQ1
DQ9
DQ2
DQ10
DQ3
DQ11
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
SO
RESET#
WE#
A8
A9
A10
A11
A12
A13
A14
A15
A16
BYTE#
VSS
DQ15/A-1
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
FBGA
Top View, Balls Facing Down
A6
B6
C6
D6
E6
F6
G6
H6
A13
A12
A14
A15
A16
BYTE#
DQ15/A-1
VSS
A5
B5
C5
D5
E5
F5
G5
H5
A9
A8
A10
A11
DQ7
DQ14
DQ13
DQ6
A4
B4
C4
D4
E4
F4
G4
H4
WE#
RESET#
NC
NC
DQ5
DQ12
VCC
DQ4
A3
B3
C3
D3
E3
F3
G3
H3
RY/BY#
NC
A18
NC
DQ2
DQ10
DQ11
DQ3
A2
B2
C2
D2
E2
F2
G2
H2
A7
A17
A6
A5
DQ0
DQ8
DQ9
DQ1
A1
B1
C1
D1
E1
F1
G1
H1
A3
A4
A2
A1
A0
CE#
OE#
VSS
Special Handling Instructions for FBGA Package
Special handling is required for Flash Memory products in FBGA packages.Flash
memory devices in FBGA packages may be damaged if exposed to ultrasonic
cleaning methods. The package and/or data integrity may be compromised if the
package body is exposed to temperatures above 150°C for prolonged periods of
time.
8
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Pin Configuration
A0–A18
=
19 addresses
DQ0–DQ14
=
15 data inputs/outputs
DQ15/A-1
=
DQ15 (data input/output, word
mode),
A-1 (LSB address input, byte
mode)
BYTE#
=
Selects 8-bit or 16-bit mode
CE#
=
Chip enable
OE#
=
Output enable
WE#
=
Write enable
RESET#
=
Hardware reset pin, active low
RY/BY#
=
Ready/Busy# output
VCC
=
3.0 volt-only single power supply
(see Product Selector Guide for speed
options and voltage supply tolerances)
VSS
=
Device ground
NC
=
Pin not connected internally
Logic Symbol
19
A0–A18
16 or 8
DQ0–DQ15
(A-1)
CE#
OE#
WE#
RESET#
BYTE#
June 16, 2005 S29AL008D_00A3
RY/BY#
S29AL008D
9
D a t a
S h e e t
Ordering Information
Standard Products
Spansion standard products are available in several packages and operating
ranges. The order number (Valid Combination) is formed by a combination of the
elements below.
S29AL008D
55
T
A
I
RI
0
PACKING TYPE
0
1
2
3
=
=
=
=
Tray
Tube
7” Tape and Reel
13” Tape and Reel
MODEL NUMBER
01
R1
02
R2
=
=
=
=
x8/x16,
x8/x16,
x8/x16,
x8/x16,
VCC
VCC
VCC
VCC
=
=
=
=
2.7
3.0
2.7
3.0
-
3.6V,
3.6V.
3.6V,
3.6V.
top boot sector device
top boot sector device
bottom boot sector device
bottom boot sector device
TEMPERATURE RANGE
I
N
= Industrial (-40°C to +85°C)
= Extended (-40°C to +125°C)
PACKAGE MATERIAL SET
A
F
= Standard
= Pb-Free
PACKAGE TYPE
T
B
M
= Thin Small Outline Package (TSOP) Standard Pinout
= Fine-pitch Ball-Grid Array Package
= Small Outline Package (SOP) Standard Pinout
SPEED OPTION
55
70
90
= 55 ns Access Speed
= 70 ns Access Speed
= 90 ns Access Speed
DEVICE NUMBER/DESCRIPTION
S29AL008D
8 Megabit Flash Memory manufactured using 200 nm process technology
3.0 Volt-only Read, Program, and Erase
S29AL008D Valid Combinations
Device Number
S29AL008D
Speed
Option
Package Type,
Material, and
Temperature Range
Model
Number
55
TAI, TFI
R1, R2
70, 90
TAI, TFI, TAN, TFN
01, 02
55
BAI, BFI
R1, R2
70, 90
BAI, BF, BAN, BFN
01, 02
55
MAI, MFI
R1, R2
70, 90
MAI, MFI, MAN, MFN
01, 02
Packing Type
Package Description
0, 3 (Note 1)
TS048 (Note 3)
TSOP
0, 2, 3 (Note 1)
VBK048 (Note 4)
Fine-Pitch BGA
0, 1, 3 (Note 2)
SO044 (Note 3)
SOP
Notes:
1. Type 0 is standard. Specify other options as required.
2. Type 1 is standard. Specify other options as required.
3. TSOP and SOP package markings omit packing type designator from ordering part number.
4. BGA package marking omits leading S29 and packing type designator from ordering part number.
Valid Combinations
Valid Combinations list configurations planned to be supported in volume for this device. Consult
your local sales office to confirm availability of specific valid combinations and to check on newly
released combinations.
10
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Device Bus Operations
This section describes the requirements and use of the device bus operations,
which are initiated through the internal command register. The command register
itself does not occupy any addressable memory location. The register is composed of latches that store the commands, along with the address and data
information needed to execute the command. The contents of the register serve
as inputs to the internal state machine. The state machine outputs dictate the
function of the device. Table 1 lists the device bus operations, the inputs and control levels they require, and the resulting output. The following subsections
describe each of these operations in further detail.
Table 1.
S29AL008D Device Bus Operations
DQ8–DQ15
Operation
CE#
OE# WE# RESET#
Addresses
(Note 1)
DQ0–
DQ7
BYTE#
= VIH
BYTE#
= VIL
Read
L
L
H
H
AIN
DOUT
DOUT
Write
L
H
L
H
AIN
DIN
DIN
DQ8–DQ14 = High-Z,
DQ15 = A-1
VCC ±
0.3 V
X
X
VCC ±
0.3 V
X
High-Z
High-Z
High-Z
Output Disable
L
H
H
H
X
High-Z
High-Z
High-Z
Reset
X
X
X
L
X
High-Z
High-Z
High-Z
Sector Protect (Note 2)
L
H
L
VID
Sector Address,
A6 = L, A1 = H,
A0 = L
DIN
X
X
Sector Unprotect (Note 2)
L
H
L
VID
Sector Address,
A6 = H, A1 = H,
A0 = L
DIN
X
X
Temporary Sector Unprotect
X
X
X
VID
AIN
DIN
DIN
High-Z
Standby
Legend:
L = Logic Low = VIL, H = Logic High = VIH, VID = 12.0 ± 0.5 V, X = Don’t Care, AIN = Address In, DIN = Data In, DOUT = Data Out
Notes:
1. Addresses are A18:A0 in word mode (BYTE# = VIH), A18:A-1 in byte mode (BYTE# = VIL).
2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See the
Sector Protection/Unprotection, on page 16.
Word/Byte Configuration
The BYTE# pin controls whether the device data I/O pins DQ15–DQ0 operate in
the byte or word configuration. If the BYTE# pin is set at logic 1, the device is in
word configuration, DQ15–DQ0 are active and controlled by CE# and OE#.
If the BYTE# pin is set at logic 0, the device is in byte configuration, and only data
I/O pins DQ0–DQ7 are active and controlled by CE# and OE#. The data I/O pins
DQ8–DQ14 are tri-stated, and the DQ15 pin is used as an input for the LSB (A-1)
address function.
Requirements for Reading Array Data
To read array data from the outputs, the system must drive the CE# and OE#
pins to VIL. CE# is the power control and selects the device. OE# is the output
control and gates array data to the output pins. WE# should remain at VIH. The
BYTE# pin determines whether the device outputs array data in words or bytes.
June 16, 2005 S29AL008D_00A3
S29AL008D
11
D a t a
S h e e t
The internal state machine is set for reading array data upon device power-up,
or after a hardware reset. This ensures that no spurious alteration of the memory
content occurs during the power transition. No command is necessary in this
mode to obtain array data. Standard microprocessor read cycles that assert valid
addresses on the device address inputs produce valid data on the device data
outputs. The device remains enabled for read access until the command register
contents are altered.
See Reading Array Data, on page 19 for more information. Refer to the AC table
for timing specifications and to Figure 13, on page 38 for the timing diagram. ICC1
in the DC Characteristics table represents the active current specification for
reading array data.
Writing Commands/Command Sequences
To write a command or command sequence (which includes programming data
to the device and erasing sectors of memory), the system must drive WE# and
CE# to VIL, and OE# to VIH.
For program operations, the BYTE# pin determines whether the device accepts
program data in bytes or words. Refer to Word/Byte Configuration, on page 11
for more information.
The device features an Unlock Bypass mode to facilitate faster programming.
Once the device enters the Unlock Bypass mode, only two write cycles are required to program a word or byte, instead of four. The Word/Byte Program
Command Sequence, on page 20 contains details on programming data to the
device using both standard and Unlock Bypass command sequences.
An erase operation can erase one sector, multiple sectors, or the entire device.
Table 2, on page 14 and Table 3, on page 15 indicate the address space that each
sector occupies. A sector address consists of the address bits required to uniquely
select a sector. The Command Definitions, on page 19 contains details on erasing
a sector or the entire chip, or suspending/resuming the erase operation.
After the system writes the autoselect command sequence, the device enters the
autoselect mode. The system can then read autoselect codes from the internal
register (which is separate from the memory array) on DQ7–DQ0. Standard read
cycle timings apply in this mode. Refer to the Autoselect Mode, on page 15 and
Autoselect Command Sequence, on page 20 for more information.
ICC2 in the DC Characteristics table represents the active current specification for
the write mode. The AC Characteristics, on page 38 contains timing specification
tables and timing diagrams for write operations.
Program and Erase Operation Status
During an erase or program operation, the system may check the status of the
operation by reading the status bits on DQ7–DQ0. Standard read cycle timings
and ICC read specifications apply. Refer to Write Operation Status, on page 27
for more information, and to AC Characteristics, on page 38 for timing diagrams.
Standby Mode
When the system is not reading or writing to the device, it can place the device
in the standby mode. In this mode, current consumption is greatly reduced, and
the outputs are placed in the high impedance state, independent of the OE#
input.
12
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
The device enters the CMOS standby mode when the CE# and RESET# pins are
both held at VCC ± 0.3 V. (Note that this is a more restricted voltage range than
VIH.) If CE# and RESET# are held at VIH, but not within VCC ± 0.3 V, the device
is in the standby mode, but the standby current is greater. The device requires
standard access time (tCE) for read access when the device is in either of these
standby modes, before it is ready to read data.
If the device is deselected during erasure or programming, the device draws active current until the operation is completed.
In the DC Characteristics table, ICC3 and ICC4 represents the standby current
specification.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses remain stable for tACC + 30
ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control
signals. Standard address access timings provide new data when addresses are
changed. While in sleep mode, output data is latched and always available to the
system. ICC4 in the DC Characteristics table represents the automatic sleep mode
current specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of resetting the device to reading
array data. When the RESET# pin is driven low for at least a period of tRP, the
device immediately terminates any operation in progress, tristates all output
pins, and ignores all read/write commands for the duration of the RESET# pulse.
The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to
accept another command sequence, to ensure data integrity.
Current is reduced for the duration of the RESET# pulse. When RESET# is held
at VSS±0.3 V, the device draws CMOS standby current (ICC4). If RESET# is held
at VIL but not within VSS±0.3 V, the standby current is greater.
The RESET# pin may be tied to the system reset circuitry. A system reset would
thus also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory.
If RESET# is asserted during a program or erase operation, the RY/BY# pin remains a 0 (busy) until the internal reset operation is complete, which requires a
time of tREADY (during Embedded Algorithms). The system can thus monitor RY/
BY# to determine whether the reset operation is complete. If RESET# is asserted
when a program or erase operation is not executing (RY/BY# pin is 1), the reset
operation is completed within a time of tREADY (not during Embedded Algorithms).
The system can read data tRH after the RESET# pin returns to VIH.
Refer to AC Characteristics, on page 38 for RESET# parameters and to Figure
14, on page 39 for the timing diagram.
Output Disable Mode
When the OE# input is at VIH, output from the device is disabled. The output pins
are placed in the high impedance state.
June 16, 2005 S29AL008D_00A3
S29AL008D
13
D a t a
Table 2.
S h e e t
S29AL008D Top Boot Block Sector Addresses
Address Range (in hexadecimal)
Sector
A18
A17
A16
A15
A14
A13
A12
Sector Size
(Kbytes/
Kwords)
SA0
0
0
0
0
X
X
X
64/32
00000h–0FFFFh
00000h–07FFFh
SA1
0
0
0
1
X
X
X
64/32
10000h–1FFFFh
08000h–0FFFFh
SA2
0
0
1
0
X
X
X
64/32
20000h–2FFFFh
10000h–17FFFh
SA3
0
0
1
1
X
X
X
64/32
30000h–3FFFFh
18000h–1FFFFh
SA4
0
1
0
0
X
X
X
64/32
40000h–4FFFFh
20000h–27FFFh
SA5
0
1
0
1
X
X
X
64/32
50000h–5FFFFh
28000h–2FFFFh
SA6
0
1
1
0
X
X
X
64/32
60000h–6FFFFh
30000h–37FFFh
SA7
0
1
1
1
X
X
X
64/32
70000h–7FFFFh
38000h–3FFFFh
SA8
1
0
0
0
X
X
X
64/32
80000h–8FFFFh
40000h–47FFFh
SA9
1
0
0
1
X
X
X
64/32
90000h–9FFFFh
48000h–4FFFFh
SA10
1
0
1
0
X
X
X
64/32
A0000h–AFFFFh
50000h–57FFFh
SA11
1
0
1
1
X
X
X
64/32
B0000h–BFFFFh
58000h–5FFFFh
SA12
1
1
0
0
X
X
X
64/32
C0000h–CFFFFh
60000h–67FFFh
SA13
1
1
0
1
X
X
X
64/32
D0000h–DFFFFh
68000h–6FFFFh
SA14
1
1
1
0
X
X
X
64/32
E0000h–EFFFFh
70000h–77FFFh
SA15
1
1
1
1
0
X
X
32/16
F0000h–F7FFFh
78000h–7BFFFh
SA16
1
1
1
1
1
0
0
8/4
F8000h–F9FFFh
7C000h–7CFFFh
SA17
1
1
1
1
1
0
1
8/4
FA000h–FBFFFh
7D000h–7DFFFh
SA18
1
1
1
1
1
1
X
16/8
FC000h–FFFFFh
7E000h–7FFFFh
14
S29AL008D
(x8)
Address Range
(x16)
Address Range
S29AL008D_00A3 June 16, 2005
D a t a
Table 3.
S h e e t
S29AL008D Bottom Boot Block Sector Addresses
Address Range (in hexadecimal)
Sector
A18
A17
A16
A15
A14
A13
A12
Sector Size
(Kbytes/
Kwords)
SA0
0
0
0
0
0
0
X
16/8
00000h–03FFFh
00000h–01FFFh
SA1
0
0
0
0
0
1
0
8/4
04000h–05FFFh
02000h–02FFFh
SA2
0
0
0
0
0
1
1
8/4
06000h–07FFFh
03000h–03FFFh
SA3
0
0
0
0
1
X
X
32/16
08000h–0FFFFh
04000h–07FFFh
SA4
0
0
0
1
X
X
X
64/32
10000h–1FFFFh
08000h–0FFFFh
SA5
0
0
1
0
X
X
X
64/32
20000h–2FFFFh
10000h–17FFFh
SA6
0
0
1
1
X
X
X
64/32
30000h–3FFFFh
18000h–1FFFFh
SA7
0
1
0
0
X
X
X
64/32
40000h–4FFFFh
20000h–27FFFh
SA8
0
1
0
1
X
X
X
64/32
50000h–5FFFFh
28000h–2FFFFh
SA9
0
1
1
0
X
X
X
64/32
60000h–6FFFFh
30000h–37FFFh
SA10
0
1
1
1
X
X
X
64/32
70000h–7FFFFh
38000h–3FFFFh
SA11
1
0
0
0
X
X
X
64/32
80000h–8FFFFh
40000h–47FFFh
SA12
1
0
0
1
X
X
X
64/32
90000h–9FFFFh
48000h–4FFFFh
SA13
1
0
1
0
X
X
X
64/32
A0000h–AFFFFh
50000h–57FFFh
SA14
1
0
1
1
X
X
X
64/32
B0000h–BFFFFh
58000h–5FFFFh
SA15
1
1
0
0
X
X
X
64/32
C0000h–CFFFFh
60000h–67FFFh
SA16
1
1
0
1
X
X
X
64/32
D0000h–DFFFFh
68000h–6FFFFh
SA17
1
1
1
0
X
X
X
64/32
E0000h–EFFFFh
70000h–77FFFh
SA18
1
1
1
1
X
X
X
64/32
F0000h–FFFFFh
78000h–7FFFFh
(x8)
Address Range
(x16)
Address Range
Note for Tables and : Address range is A18:A-1 in byte mode and A18:A0 in word mode. See Word/Byte Configuration, on page 11.
Autoselect Mode
The autoselect mode provides manufacturer and device identification, and sector
protection verification, through identifier codes output on DQ7–DQ0. This mode
is primarily intended for programming equipment to automatically match a device
to be programmed with its corresponding programming algorithm. However, the
autoselect codes can also be accessed in-system through the command register.
When using programming equipment, the autoselect mode requires VID (11.5 V
to 12.5 V) on address pin A9. Address pins A6, A1, and A0 must be as shown in
Table 4, on page 16. In addition, when verifying sector protection, the sector address must appear on the appropriate highest order address bits (see Table 2, on
page 14 and Table 3, on page 15). Table 4, on page 16 shows the remaining address bits that are don’t care. When all necessary bits are set as required, the
programming equipment may then read the corresponding identifier code on
DQ7–DQ0.
To access the autoselect codes in-system, the host system can issue the autoselect command via the command register, as shown in Table 5, on page 25. This
method does not require VID. See Command Definitions, on page 19 for details
on using the autoselect mode.
June 16, 2005 S29AL008D_00A3
S29AL008D
15
D a t a
Table 4.
Description
Mode
CE#
S29AL008D Autoselect Codes (High Voltage Method)
A18 A11
to
to
OE# WE# A12 A10
Manufacturer ID: Spansion
L
L
H
Device ID:
Am29LV800B
(Top Boot Block)
Word
L
L
H
Byte
L
L
H
Device ID:
Am29LV800B
(Bottom Boot
Block)
Word
L
L
H
Byte
L
L
H
Sector Protection
Verification
L
S h e e t
L
H
A9
A8
to
A7
A6
A5
to
A2
A1
A0
DQ8
to
DQ15
DQ7
to
DQ0
X
01h
22h
DAh
X
DAh
22h
5Bh
X
5Bh
X
01h
(protected)
X
00h
(unprotected
)
X
X
VID
X
L
X
L
L
X
X
VID
X
L
X
L
H
X
SA
X
X
VID
VID
X
X
L
L
X
X
L
H
H
L
L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care.
Sector Protection/Unprotection
The hardware sector protection feature disables both program and erase operations in any sector. The hardware sector unprotection feature re-enables both
program and erase operations in previously protected sectors.
The device is shipped with all sectors unprotected. Spansion offers the option of
programming and protecting sectors at its factory prior to shipping the device
through Spansion’s ExpressFlash™ Service. Contact an Spansion representative
for details.
It is possible to determine whether a sector is protected or unprotected. See
Autoselect Mode, on page 15 for details.
Sector Protection/unprotection can be implemented via two methods.
The primary method requires VID on the RESET# pin only, and can be implemented either in-system or via programming equipment. Figure 2, on page 18
shows the algorithms and Figure 23, on page 47 shows the timing diagram. This
method uses standard microprocessor bus cycle timing. For sector unprotect, all
unprotected sectors must first be protected prior to the first sector unprotect
write cycle.
The alternate method intended only for programming equipment requires VID on
address pin A9 and OE#. This method is compatible with programmer routines
written for earlier 3.0 volt-only Spansion flash devices. Publication number 20536
contains further details; contact an Spansion representative to request a copy.
Temporary Sector Unprotect
This feature allows temporary unprotection of previously protected sectors to
change data in-system. The Sector Unprotect mode is activated by setting the
RESET# pin to VID. During this mode, formerly protected sectors can be programmed or erased by selecting the sector addresses. Once VID is removed from
the RESET# pin, all the previously protected sectors are protected again.
16
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Figure 1 shows the algorithm, and Figure 22, on page 46 shows the timing diagrams, for this feature.
START
RESET# = VID (Note 1)
Perform Erase or
Program Operations
RESET# = VIH
Temporary Sector
Unprotect Completed
(Note 2)
Notes:
1. All protected sectors unprotected.
2. All previously protected sectors are protected once
again.
Figure 1.
June 16, 2005 S29AL008D_00A3
Temporary Sector Unprotect Operation
S29AL008D
17
D a t a
S h e e t
START
START
Protect all sectors:
The indicated portion
of the sector protect
algorithm must be
performed for all
unprotected sectors
prior to issuing the
first sector
unprotect address
PLSCNT = 1
RESET# = VID
Wait 1 ms
Temporary Sector
Unprotect Mode
No
PLSCNT = 1
RESET# = VID
Wait 1 ms
First Write No
Cycle = 60h?
First Write
Cycle = 60h?
Yes
Yes
Set up sector
address
No
Sector Protect:
Write 60h to sector
address with
A6 = 0, A1 = 1,
A0 = 0
Wait 150
Increment
PLSCNT
Temporary Sector
Unprotect Mode
All sectors
protected?
Yes
Set up first sector
address
Sector Unprotect:
Write 60h to sector
address with
A6 = 1, A1 = 1,
A0 = 0
s
Verify Sector
Protect: Write 40h
to sector address
with A6 = 0,
A1 = 1, A0 = 0
Reset
PLSCNT = 1
Read from
sector address
with A6 = 0,
A1 = 1, A0 = 0
Wait 15 ms
Verify Sector
Unprotect: Write
40h to sector
address with
A6 = 1, A1 = 1,
A0 = 0
Increment
PLSCNT
No
No
PLSCNT
= 25?
Yes
Device failed
Read from
sector address
with A6 = 1,
A1 = 1, A0 = 0
Data = 01h?
Yes
Protect another
sector?
No
Yes
PLSCNT
= 1000?
No
Remove VID
from RESET#
Yes
Device failed
Write reset
command
Sector Protect
Algorithm
Sector Protect
complete
Set up
next sector
address
No
Data = 00h?
Yes
Last sector
verified?
No
Yes
Sector Unprotect
Algorithm
Remove VID
from RESET#
Write reset
command
Sector Unprotect
complete
Figure 2.
18
In-System Sector Protect/Sector Unprotect Algorithms
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Hardware Data Protection
The command sequence requirement of unlock cycles for programming or erasing
provides data protection against inadvertent writes (refer to Table 5, on page 25
for command definitions). In addition, the following hardware data protection
measures prevent accidental erasure or programming, which might otherwise be
caused by spurious system level signals during VCC power-up and power-down
transitions, or from system noise.
Low VCC Write Inhibit
When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all
internal program/erase circuits are disabled, and the device resets. Subsequent
writes are ignored until VCC is greater than VLKO. The system must provide the
proper signals to the control pins to prevent unintentional writes when VCC is
greater than VLKO.
Write Pulse Glitch Protection
Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write
cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# =
VIH. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a
logical one.
Power-Up Write Inhibit
If WE# = CE# = VIL and OE# = VIH during power up, the device does not accept
commands on the rising edge of WE#. The internal state machine is automatically
reset to reading array data on power-up.
Command Definitions
Writing specific address and data commands or sequences into the command
register initiates device operations. Table 5, on page 25 defines the valid register
command sequences. Writing incorrect address and data values or writing
them in the improper sequence resets the device to reading array data.
All addresses are latched on the falling edge of WE# or CE#, whichever happens
later. All data is latched on the rising edge of WE# or CE#, whichever happens
first. Refer to the appropriate timing diagrams in the AC Characteristics, on
page 38.
Reading Array Data
The device is automatically set to reading array data after device power-up. No
commands are required to retrieve data. The device is also ready to read array
data after completing an Embedded Program or Embedded Erase algorithm.
After the device accepts an Erase Suspend command, the device enters the Erase
Suspend mode. The system can read array data using the standard read timings,
except that if it reads at an address within erase-suspended sectors, the device
outputs status data. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception.
See Erase Suspend/Erase Resume Commands, on page 23 for more information
on this mode.
June 16, 2005 S29AL008D_00A3
S29AL008D
19
D a t a
S h e e t
The system must issue the reset command to re-enable the device for reading
array data if DQ5 goes high, or while in the autoselect mode. See the Reset Command, next.
See also Requirements for Reading Array Data, on page 11 for more information.
The table provides the read parameters, and Figure 13, on page 38 shows the
timing diagram.
Reset Command
Writing the reset command to the device resets the device to reading array data.
Address bits are don’t care for this command.
The reset command may be written between the sequence cycles in an erase
command sequence before erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ignores reset commands until the
operation is complete.
The reset command may be written between the sequence cycles in a program
command sequence before programming begins. This resets the device to reading array data (also applies to programming in Erase Suspend mode). Once
programming begins, however, the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect
command sequence. Once in the autoselect mode, the reset command must be
written to return to reading array data (also applies to autoselect during Erase
Suspend).
If DQ5 goes high during a program or erase operation, writing the reset command
returns the device to reading array data (also applies during Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manufacturer and devices codes, and determine whether or not a sector is protected.
Table 5, on page 25 shows the address and data requirements. This method is an
alternative to that shown in Table 4, on page 16, which is intended for PROM programmers and requires VID on address bit A9.
The autoselect command sequence is initiated by writing two unlock cycles, followed by the autoselect command. The device then enters the autoselect mode,
and the system may read at any address any number of times, without initiating
another command sequence.
A read cycle at address XX00h retrieves the manufacturer code. A read cycle at
address XX01h in word mode (or 02h in byte mode) returns the device code. A
read cycle containing a sector address (SA) and the address 02h in word mode
(or 04h in byte mode) returns 01h if that sector is protected, or 00h if it is unprotected. Refer to Table 2, on page 14 and Table 3, on page 15 for valid sector
addresses.
The system must write the reset command to exit the autoselect mode and return
to reading array data.
Word/Byte Program Command Sequence
The system may program the device by word or byte, depending on the state of
the BYTE# pin. Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles, followed by the
20
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
program set-up command. The program address and data are written next, which
in turn initiate the Embedded Program algorithm. The system is not required to
provide further controls or timings. The device automatically provides internally
generated program pulses and verifies the programmed cell margin. Table 5, on
page 25 shows the address and data requirements for the byte program command sequence.
When the Embedded Program algorithm is complete, the device then returns to
reading array data and addresses are no longer latched. The system can determine the status of the program operation by using DQ7, DQ6, or RY/BY#. See
Write Operation Status, on page 27 for information on these status bits.
Any commands written to the device during the Embedded Program Algorithm
are ignored. Note that a hardware reset immediately terminates the programming operation. The program command sequence should be reinitiated once the
device resets to reading array data, to ensure data integrity.
Programming is allowed in any sequence and across sector boundaries. A bit
cannot be programmed from a 0 back to a 1. Attempting to do so may halt
the operation and set DQ5 to 1, or cause the Data# Polling algorithm to indicate
the operation was successful. However, a succeeding read shows that the data is
still 0. Only erase operations can convert a 0 to a 1.
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program bytes or words to the
device faster than using the standard program command sequence. The unlock
bypass command sequence is initiated by first writing two unlock cycles. This is
followed by a third write cycle containing the unlock bypass command, 20h. The
device then enters the unlock bypass mode. A two-cycle unlock bypass program
command sequence is all that is required to program in this mode. The first cycle
in this sequence contains the unlock bypass program command, A0h; the second
cycle contains the program address and data. Additional data is programmed in
the same manner. This mode dispenses with the initial two unlock cycles required
in the standard program command sequence, resulting in faster total programming time. Table 5, on page 25 shows the requirements for the command
sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset command sequence. The first cycle
must contain the data 90h; the second cycle the data 00h. Addresses are don’t
care for both cycles. The device then returns to reading array data.
Figure 3, on page 22 illustrates the algorithm for the program operation. See
Erase / Program Operations, on page 42 i for parameters, and Figure 17, on
page 43 for timing diagrams.
June 16, 2005 S29AL008D_00A3
S29AL008D
21
D a t a
S h e e t
START
Write Program
Command Sequence
Data Poll
from System
Embedded
Program
algorithm
in progress
Verify Data?
No
Yes
Increment Address
No
Last Address?
Yes
Programming
Completed
Note: See Table 5, on page 25 for program command sequence.
Figure 3.
Program Operation
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two
additional unlock write cycles are then followed by the chip erase command,
which in turn invokes the Embedded Erase algorithm. The device does not require
the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all zero data pattern
prior to electrical erase. The system is not required to provide any controls or timings during these operations. Table 5, on page 25 shows the address and data
requirements for the chip erase command sequence.
Any commands written to the chip during the Embedded Erase algorithm are ignored. Note that a hardware reset during the chip erase operation immediately
terminates the operation. The Chip Erase command sequence should be reinitiated once the device returns to reading array data, to ensure data integrity.
The system can determine the status of the erase operation by using DQ7, DQ6,
DQ2, or RY/BY#. See Write Operation Status, on page 27 for information on
these status bits. When the Embedded Erase algorithm is complete, the device
returns to reading array data and addresses are no longer latched.
22
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Figure 4, on page 25 illustrates the algorithm for the erase operation. See Erase
/ Program Operations, on page 42 for parameters, and Figure 18, on page 44 for
timing diagrams.
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector erase command sequence is
initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the address of the sector to be
erased, and the sector erase command. Table 5, on page 25 shows the address
and data requirements for the sector erase command sequence.
The device does not require the system to preprogram the memory prior to erase.
The Embedded Erase algorithm automatically programs and verifies the sector for
an all zero data pattern prior to electrical erase. The system is not required to
provide any controls or timings during these operations.
After the command sequence is written, a sector erase time-out of 50 µs begins.
During the time-out period, additional sector addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any
sequence, and the number of sectors may be from one sector to all sectors. The
time between these additional cycles must be less than 50 µs, otherwise the last
address and command might not be accepted, and erasure may begin. It is recommended that processor interrupts be disabled during this time to ensure all
commands are accepted. The interrupts can be re-enabled after the last Sector
Erase command is written. If the time between additional sector erase commands
can be assumed to be less than 50 µs, the system need not monitor DQ3. Any
command other than Sector Erase or Erase Suspend during the time-out
period resets the device to reading array data. The system must rewrite the
command sequence and any additional sector addresses and commands.
The system can monitor DQ3 to determine if the sector erase timer has timed
out. (See DQ3: Sector Erase Timer, on page 30.) The time-out begins from the
rising edge of the final WE# pulse in the command sequence.
Once the sector erase operation begins, only the Erase Suspend command is
valid. All other commands are ignored. Note that a hardware reset during the
sector erase operation immediately terminates the operation. The Sector Erase
command sequence should be reinitiated once the device returns to reading array
data, to ensure data integrity.
When the Embedded Erase algorithm is complete, the device returns to reading
array data and addresses are no longer latched. The system can determine the
status of the erase operation by using DQ7, DQ6, DQ2, or RY/BY#. Refer to Write
Operation Status, on page 27 for information on these status bits.
Figure 4, on page 25 illustrates the algorithm for the erase operation. Refer to
Erase / Program Operations, on page 42 for parameters, and to Figure 18, on
page 44 for timing diagrams.
Erase Suspend/Erase Resume Commands
The Erase Suspend command allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for
erasure. This command is valid only during the sector erase operation, including
the 50 µs time-out period during the sector erase command sequence. The Erase
Suspend command is ignored if written during the chip erase operation or Embedded Program algorithm. Writing the Erase Suspend command during the
June 16, 2005 S29AL008D_00A3
S29AL008D
23
D a t a
S h e e t
Sector Erase time-out immediately terminates the time-out period and suspends
the erase operation. Addresses are don’t-cares when writing the Erase Suspend
command.
When the Erase Suspend command is written during a sector erase operation, the
device requires a maximum of 20 µs to suspend the erase operation. However,
when the Erase Suspend command is written during the sector erase time-out,
the device immediately terminates the time-out period and suspends the erase
operation.
After the erase operation is suspended, the system can read array data from or
program data to any sector not selected for erasure. (The device erase suspends
all sectors selected for erasure.) Normal read and write timings and command
definitions apply. Reading at any address within erase-suspended sectors produces status data on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2
together, to determine if a sector is actively erasing or is erase-suspended. See
Write Operation Status, on page 27 for information on these status bits.
After an erase-suspended program operation is complete, the system can once
again read array data within non-suspended sectors. The system can determine
the status of the program operation using the DQ7 or DQ6 status bits, just as in
the standard program operation. See Write Operation Status, on page 27 for
more information.
The system may also write the autoselect command sequence when the device
is in the Erase Suspend mode. The device allows reading autoselect codes even
at addresses within erasing sectors, since the codes are not stored in the memory
array. When the device exits the autoselect mode, the device reverts to the Erase
Suspend mode, and is ready for another valid operation. See Autoselect Command Sequence, on page 20 for more information.
The system must write the Erase Resume command (address bits are don’t care)
to exit the erase suspend mode and continue the sector erase operation. Further
writes of the Resume command are ignored. Another Erase Suspend command
can be written after the device resumes erasing.
24
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
START
Write Erase
Command Sequence
Data Poll
from System
Embedded
Erase
algorithm
in progress
No
Data = FFh?
Yes
Erasure Completed
Notes:
1. See Table 5, on page 25 for erase command sequence.
2. See DQ3: Sector Erase Timer, on page 30 for more information.
Figure 4.
Table 5.
Read (Note 6)
Reset (Note 7)
Autoselect (Note 8)
Manufacturer ID
Word
Byte
Device ID,
Top Boot Block
Word
Device ID,
Bottom Boot Block
Word
Sector Protect Verify
(Note 9)
Program
Unlock Bypass
Byte
Byte
Data
1
RA
RD
1
XXX
F0
4
4
4
First
555
AAA
555
AAA
555
AAA
Second
AA
AA
AA
555
4
2AA
555
2AA
555
2AA
555
Data
55
55
55
2AA
AA
Third
Addr
555
AAA
555
AAA
555
AAA
AAA
Word
555
2AA
555
Word
Byte
Word
Byte
Word
Byte
4
3
2
2
6
6
AAA
555
AAA
AA
AA
555
2AA
555
55
55
XXX
A0
PA
PD
XXX
90
XXX
00
555
AAA
555
AAA
AA
AA
1
XXX
B0
Erase Resume (Note 13)
1
XXX
30
2AA
555
2AA
555
Addr
Data
90
X00
01
X01
22DA
90
90
90
555
Byte
Fourth
Data
555
55
AAA
Erase Suspend (Note 12)
June 16, 2005 S29AL008D_00A3
Addr
Byte
Unlock Bypass Program (Note 10)
Sector Erase
Bus Cycles (Notes 2-5)
Addr
Word
Unlock Bypass Reset (Note 11)
Chip Erase
S29AL008D Command Definitions
Cycles
Command
Sequence
(Note 1)
Erase Operation
55
55
S29AL008D
AAA
555
AAA
555
AAA
555
AAA
A0
X02
DA
X01
225B
X02
5B
(SA)
X02
XX00
(SA)
X04
00
PA
PD
Fifth
Addr
Sixth
Data
Addr
Data
XX01
01
20
80
80
555
AAA
555
AAA
AA
AA
2AA
555
2AA
555
55
55
555
AAA
SA
10
30
25
D a t a
S h e e t
Legend:
X = Don’t care, RA = Address of the memory location to be read, RD = Data read from location RA during read operation, and
PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE# or CE# pulse, whichever
happens later. PD = Data to be programmed at location PA. Data latches on the rising edge of WE# or CE# pulse, whichever
happens first. SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits A18–A12 uniquely select any
sector.
Notes:
1. See Table 1, on page 11 for a description of bus operations.
2. All values are in hexadecimal.
3. Except when reading array or autoselect data, all bus cycles are write operations.
4. Data bits DQ15–DQ8 are don’t cares for unlock and command cycles.
5. Address bits A18–A11 are don’t cares for unlock and command cycles, unless PA or SA required.
6. No unlock or command cycles required when reading array data.
7. The Reset command is required to return to reading array data when device is in the autoselect mode, or if DQ5
goes high (while the device is providing status data).
8. The fourth cycle of the autoselect command sequence is a read cycle.
9. The data is 00h for an unprotected sector and 01h for a protected sector. See Autoselect Command Sequence, on
page 20 for more information.
10.The Unlock Bypass command is required prior to the Unlock Bypass Program command.
11.The Unlock Bypass Reset command is required to return to reading array data when the device is in the unlock
bypass mode.
12.The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend
mode. The Erase Suspend command is valid only during a sector erase operation.
13.The Erase Resume command is valid only during the Erase Suspend mode.
26
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Write Operation Status
The device provides several bits to determine the status of a write operation:
DQ2, DQ3, DQ5, DQ6, DQ7, and RY/BY#. Table 6, on page 32 and the following
subsections describe the functions of these bits. DQ7, RY/BY#, and DQ6 each
offer a method for determining whether a program or erase operation is complete
or in progress. These three bits are discussed first.
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded
Algorithm is in progress or completed, or whether the device is in Erase Suspend.
Data# Polling is valid after the rising edge of the final WE# pulse in the program
or erase command sequence.
During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to
programming during Erase Suspend. When the Embedded Program algorithm is
complete, the device outputs the datum programmed to DQ7. The system must
provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data# Polling on DQ7 is active for
approximately 1 µs, then the device returns to reading array data.
During the Embedded Erase algorithm, Data# Polling produces a 0 on DQ7. When
the Embedded Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a 1 on DQ7. This is analogous to the
complement/true datum output described for the Embedded Program algorithm:
the erase function changes all the bits in a sector to 1; prior to this, the device
outputs the complement, or 0. The system must provide an address within any
of the sectors selected for erasure to read valid status information on DQ7.
After an erase command sequence is written, if all sectors selected for erasing
are protected, Data# Polling on DQ7 is active for approximately 100 µs, then the
device returns to reading array data. If not all selected sectors are protected, the
Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected.
When the system detects DQ7 changes from the complement to true data, it can
read valid data at DQ7–DQ0 on the following read cycles. This is because DQ7
may change asynchronously with DQ0–DQ6 while Output Enable (OE#) is ass er te d l o w. F ig u r e 1 9 , o n p ag e 4 5, D at a# Po l l in g T im i n g s ( D u ri n g
Embedded Algorithms), illustrates this.
Table 6, on page 32 shows the outputs for Data# Polling on DQ7. Figure 5, on
page 28 shows the Data# Polling algorithm.
June 16, 2005 S29AL008D_00A3
S29AL008D
27
D a t a
S h e e t
START
Read DQ7–DQ0
Addr = VA
DQ7 = Data?
Yes
No
No
DQ5 = 1?
Yes
Read DQ7–DQ0
Addr = VA
DQ7 = Data?
Yes
No
PASS
FAIL
Notes:
1. VA = Valid address for programming. During a sector
erase operation, a valid address is an address within
any sector selected for erasure. During chip erase, a
valid address is any non-protected sector address.
2. DQ7 should be rechecked even if DQ5 = 1 because
DQ7 may change simultaneously with DQ5.
Figure 5.
Data# Polling Algorithm
RY/BY#: Ready/Busy#
The RY/BY# is a dedicated, open-drain output pin that indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the
rising edge of the final WE# pulse in the command sequence. Since RY/BY# is an
open-drain output, several RY/BY# pins can be tied together in parallel with a
pull-up resistor to VCC.
28
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
If the output is low (Busy), the device is actively erasing or programming. (This
includes programming in the Erase Suspend mode.) If the output is high (Ready),
the device is ready to read array data (including during the Erase Suspend
mode), or is in the standby mode.
Table 6, on page 32 shows the outputs for RY/BY#. Figure 13, on page 38, Figure
14, Figure 17, on page 43 and Figure 18, on page 44 shows RY/BY# for read,
reset, program, and erase operations, respectively.
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm
is in progress or complete, or whether the device entered the Erase Suspend
mode. Toggle Bit I may be read at any address, and is valid after the rising edge
of the final WE# pulse in the command sequence (prior to the program or erase
operation), and during the sector erase time-out.
During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. (The system may use either OE# or CE#
to control the read cycles.) When the operation is complete, DQ6 stops toggling.
After an erase command sequence is written, if all sectors selected for erasing
are protected, DQ6 toggles for approximately 100 µs, then returns to reading
array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are
protected.
The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-suspended. When the device is actively erasing (that is,
the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must
also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7 (see the subsection DQ7: Data# Polling, on
page 27).
If a program address falls within a protected sector, DQ6 toggles for approximately 1 µs after the program command sequence is written, then returns to
reading array data.
DQ6 also toggles during the erase-suspend-program mode, and stops toggling
once the Embedded Program algorithm is complete.
Table 6, on page 32 shows the outputs for Toggle Bit I on DQ6. Figure 6, on page
31 shows the toggle bit algorithm. Figure 20, on page 45 shows the toggle bit
timing diagrams. Figure 21, on page 46 shows the differences between DQ2 and
DQ6 in graphical form. See also the subsection DQ2: Toggle Bit II, on page 29.
DQ2: Toggle Bit II
The Toggle Bit II on DQ2, when used with DQ6, indicates whether a particular
sector is actively erasing (that is, the Embedded Erase algorithm is in progress),
or whether that sector is erase-suspended. Toggle Bit II is valid after the rising
edge of the final WE# pulse in the command sequence.
DQ2 toggles when the system reads at addresses within those sectors that were
selected for erasure. (The system may use either OE# or CE# to control the read
cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or is
erase-suspended. DQ6, by comparison, indicates whether the device is actively
erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected
June 16, 2005 S29AL008D_00A3
S29AL008D
29
D a t a
S h e e t
for erasure. Thus, both status bits are required for sector and mode information.
Refer to Table 6, on page 32 to compare outputs for DQ2 and DQ6.
Figure 6, on page 31 shows the toggle bit algorithm in flowchart form, and the
section “DQ2: Toggle Bit II” explains the algorithm. See also the DQ6: Toggle Bit
I, on page 29 subsection. Figure 20, on page 45 shows the toggle bit timing diagram. Figure 21, on page 46 shows the differences between DQ2 and DQ6 in
graphical form.
Reading Toggle Bits DQ6/DQ2
Refer to Figure 6, on page 31 for the following discussion. Whenever the system
initially begins reading toggle bit status, it must read DQ7–DQ0 at least twice in
a row to determine whether a toggle bit is toggling. Typically, the system would
note and store the value of the toggle bit after the first read. After the second
read, the system would compare the new value of the toggle bit with the first. If
the toggle bit is not toggling, the device completed the program or erase operation. The system can read array data on DQ7–DQ0 on the following read cycle.
However, if after the initial two read cycles, the system determines that the toggle
bit is still toggling, the system also should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should then determine again
whether the toggle bit is toggling, since the toggle bit may have stopped toggling
just as DQ5 went high. If the toggle bit is no longer toggling, the device successfully completed the program or erase operation. If it is still toggling, the device
did not completed the operation successfully, and the system must write the reset
command to return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit
is toggling and DQ5 has not gone high. The system may continue to monitor the
toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other
system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation (top of Figure 6,
on page 31).
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time exceeded a specified internal
pulse count limit. Under these conditions DQ5 produces a 1. This is a failure condition that indicates the program or erase cycle was not successfully completed.
The DQ5 failure condition may appear if the system tries to program a 1 to a location that is previously programmed to 0. Only an erase operation can
change a 0 back to a 1. Under this condition, the device halts the operation,
and when the operation exceeds the timing limits, DQ5 produces a 1.
Under both these conditions, the system must issue the reset command to return
the device to reading array data.
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to determine whether or not an erase operation started. (The sector erase timer does
not apply to the chip erase command.) If additional sectors are selected for erasure, the entire time-out also applies after each additional sector erase
command. When the time-out is complete, DQ3 switches from 0 to 1. The system
may ignore DQ3 if the system can guarantee that the time between additional
30
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
sector erase commands is always less than 50 µs. See also the Sector Erase
Command Sequence, on page 23.
START
Read DQ7–DQ0
Note 1
Read DQ7–DQ0
No
Toggle Bit
= Toggle?
Yes
No
DQ5 = 1?
Yes
Read DQ7–DQ0
Twice
(Notes
1, 2)
Toggle Bit
= Toggle?
No
Yes
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Notes:
1. Read toggle bit twice to determine whether or not it
is toggling. See text.
2. Recheck toggle bit because it may stop toggling as
DQ5 changes to 1. See text.
Figure 6.
Toggle Bit Algorithm
After the sector erase command sequence is written, the system should read the
status on DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure the device accepted
the command sequence, and then read DQ3. If DQ3 is 1, the internally controlled
erase cycle started; all further commands (other than Erase Suspend) are ignored until the erase operation is complete. If DQ3 is 0, the device accepts
June 16, 2005 S29AL008D_00A3
S29AL008D
31
D a t a
S h e e t
additional sector erase commands. To ensure the command is accepted, the system software should check the status of DQ3 prior to and following each
subsequent sector erase command. If DQ3 is high on the second status check,
the last command might not be accepted. Table 6 shows the outputs for DQ3.
Table 6.
DQ7
(Note 2)
DQ6
DQ5
(Note 1)
DQ3
DQ2
(Note 2)
RY/BY#
DQ7#
Toggle
0
N/A
No toggle
0
0
Toggle
0
1
Toggle
0
1
No toggle
0
N/A
Toggle
1
Reading within Non-Erase
Suspended Sector
Data
Data
Data
Data
Data
1
Erase-Suspend-Program
DQ7#
Toggle
0
N/A
N/A
0
Operation
Standard Embedded Program Algorithm
Mode
Embedded Erase Algorithm
Erase
Suspend
Mode
Write Operation Status
Reading within Erase
Suspended Sector
Notes:
1. DQ5 switches to 1 when an Embedded Program or Embedded Erase operation exceeds the maximum timing limits.
See DQ5: Exceeded Timing Limits, on page 30 for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further
details.
32
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Absolute Maximum Ratings
Storage Temperature Plastic Packages . . . . . . . . . . . . . . . . .–65°C to +150°C
Ambient Temperature with Power Applied . . . . . . . . . . . . . . .–65°C to +125°C
Voltage with Respect to Ground VCC (Note 1) . . . . . . . . . . . .–0.5 V to +4.0 V
A9, OE#, and RESET# (Note 2) . . . . . . . . . . . . . . . . . . . . . –0.5 V to +12.5 V
All other pins (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC+0.5 V
Output Short Circuit Current (Note 3). . . . . . . . . . . . . . . . . . . . . . . . 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input or I/O pins may undershoot VSS
to –2.0 V for periods of up to 20 ns. See Figure 7, on page 33. Maximum DC voltage on input or I/O pins is VCC +0.5
V. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns. See Figure 8,
on page 33.
2. Minimum DC input voltage on pins A9, OE#, and RESET# is –0.5 V. During voltage transitions, A9, OE#, and
RESET# may undershoot VSS to –2.0 V for periods of up to 20 ns. See Figure 7, on page 33. Maximum DC input
voltage on pin A9 is +12.5 V which may overshoot to 14.0 V for periods up to 20 ns.
3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater
than one second.
Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections
of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may
affect device reliability.
Operating Ranges
Industrial (I) Devices
Ambient Temperature (TA) . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Extended (N) Devices
Ambient Temperature (TA) . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +125°C
VCC Supply Voltages
VCC for regulated voltage range . . . . . . . . . . . . . . . . . . . . . +3.0 V to +3.6 V
VCC for full voltage range . . . . . . . . . . . . . . . . . . . . . . . . . +2.7 V to +3.6 V
Operating ranges define those limits between which the functionality of the device is guaranteed
20 ns
20 ns
+0.8 V
20 ns
VCC
+2.0 V
VCC
+0.5 V
–0.5 V
–2.0 V
2.0 V
20 ns
Figure 7.
20 ns
Maximum Negative Overshoot Waveform Figure 8.
June 16, 2005 S29AL008D_00A3
S29AL008D
20 ns
Maximum Positive Overshoot Waveform
33
D a t a
S h e e t
DC Characteristics
Parameter
Description
Test Conditions
ILI
Input Load Current
VIN = VSS to VCC,
VCC = VCC max
ILIT
A9 Input Load Current
VCC = VCC max; A9 = 12.5 V
ILO
Output Leakage Current
VOUT = VSS to VCC,
VCC = VCC max
Min
VCC Active Read Current
(Notes 1, 2)
Max
Unit
±1.0
µA
35
µA
±1.0
µA
10 MHz
15
30
5 MHz
9
16
1 MHz
2
4
10 MHz
15
30
5 MHz
9
16
1 MHz
2
4
CE# = VIL, OE# = VIH,
Byte Mode
ICC1
Typ
CE# = VIL, OE# = VIH,
Word Mode
mA
ICC2
VCC Active Write Current
(Notes 2, 3, 6)
CE# = VIL, OE# = VIH
20
35
mA
ICC3
VCC Standby Current (Notes 2, 4)
CE#, RESET# = VCC±0.3 V
0.2
5
µA
ICC4
VCC Reset Current (Notes 2, 4)
RESET# = VSS ± 0.3 V
0.2
5
µA
ICC5
Automatic Sleep Mode
(Notes 2, 4, 5)
VIH = VCC ± 0.3 V;
VIL = VSS ± 0.3 V
0.2
5
µA
VIL
Input Low Voltage
–0.5
0.8
V
VIH
Input High Voltage
0.7 x VCC
VCC + 0.3
V
VID
Voltage for Autoselect and
Temporary Sector Unprotect
VCC = 3.3 V
11.5
12.5
V
VOL
Output Low Voltage
IOL = 4.0 mA, VCC = VCC min
0.45
V
VOH1
VOH2
VLKO
Output High Voltage
IOH = –2.0 mA, VCC = VCC min
2.4
IOH = –100 µA, VCC = VCC min
VCC–0.4
Low VCC Lock-Out Voltage
V
2.3
2.5
V
Notes:
1. The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH. Typical VCC is 3.0 V.
2. Maximum ICC specifications are tested with VCC = VCCmax.
3. ICC active while Embedded Erase or Embedded Program is in progress.
4. At extended temperature range (>+85°C), typical current is 5µA and maximum current is 10µA.
5. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns.
6. Not 100% tested.
34
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
DC Characteristics (Continued)
Zero Power Flash
Supply Current in mA
20
15
10
5
0
0
500
1000
1500
2000
2500
3000
3500
4000
Time in ns
Note: Addresses are switching at 1 MHz
Figure 9.
ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents)
10
Supply Current in mA
8
3.6 V
6
2.7 V
4
2
0
1
2
3
4
5
Frequency in MHz
Note: T = 25 °C
Figure 10.
June 16, 2005 S29AL008D_00A3
Typical ICC1 vs. Frequency
S29AL008D
35
D a t a
S h e e t
Test Conditions
3.3 V
2.7 kΩ
Device
Under
Test
CL
6.2 kΩ
Note: Nodes are IN3064 or equivalent.
Figure 11.
Table 7.
Test Setup
Test Specifications
Test Condition
55
Output Load
Output Load Capacitance, CL
(including jig capacitance)
30
Input Rise and Fall Times
30
5
Input Pulse Levels
36
70
90
Unit
100
pF
1 TTL gate
ns
0.0–3.0
Input timing measurement reference levels
1.5
Output timing measurement reference levels
1.5
S29AL008D
V
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Key to Switching Waveforms
WAVEFORM
INPUTS
OUTPUTS
Steady
Changing from H to L
Changing from L to H
3.0 V
Input
Don’t Care, Any Change Permitted
Changing, State Unknown
Does Not Apply
Center Line is High Impedance State (High Z)
1.5 V
Measurement Level
1.5 V
Output
0.0 V
Figure 12.
June 16, 2005 S29AL008D_00A3
Input Waveforms and Measurement Levels
S29AL008D
37
D a t a
S h e e t
AC Characteristics
Table 8.
Read Operations
Parameter
Speed Options
JEDEC
Std
tAVAV
tRC
Read Cycle Time (Note 1)
tAVQV
tACC
Address to Output Delay
tELQV
tCE
Chip Enable to Output Delay
tGLQV
tOE
tEHQZ
tGHQZ
tAXQX
Description
Test Setup
55
70
90
Min
55
70
90
CE# = VIL
OE# = VIL
Max
55
70
90
OE# = VIL
Max
55
70
90
Output Enable to Output Delay
Max
25
30
35
tDF
Chip Enable to Output High Z (Note 1)
Max
25
25
30
tDF
Output Enable to Output High Z (Note 1)
Max
25
25
30
Read
Min
0
Toggle and
Data# Polling
Min
10
Min
0
tOEH
Output Enable
Hold Time (Note 1)
tOH
Output Hold Time From Addresses, CE# or OE#,
Whichever Occurs First (Note 1)
Unit
ns
Notes:
1. Not 100% tested.
2. See Figure 11, on page 36 and DC Characteristics, on page 34 for test specifications.
tRC
Addresses Stable
Addresses
tACC
CE#
tD
tO
OE#
tOEH
WE#
tCE
HIGH Z
Outputs
tO
Output Valid
HIGH Z
RESET#
RY/BY#
0V
Figure 13.
38
Read Operations Timings
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
AC Characteristics
Table 9.
Hardware Reset (RESET#)
Parameter
JEDEC
Std
tREADY
tREADY
Description
Test Setup
RESET# Pin Low (During Embedded
Algorithms) to Read or Write (See Note )
All Speed Options
Unit
20
µs
Max
RESET# Pin Low (NOT During Embedded
Algorithms) to Read or Write (See Note )
500
tRP
RESET# Pulse Width
500
tRH
RESET# High Time Before Read (See Note )
tRPD
RESET# Low to Standby Mode
tRB
RY/BY# Recovery Time
ns
50
Min
20
µs
0
ns
Note: Not 100% tested.
RY/BY#
CE#, OE#
tRH
RESET#
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
tReady
RY/BY#
tRB
CE#, OE#
RESET#
tRP
Figure 14.
June 16, 2005 S29AL008D_00A3
RESET# Timings
S29AL008D
39
D a t a
S h e e t
AC Characteristics
Table 10.
Word/Byte Configuration (BYTE#)
Parameter
JEDEC
40
Std
Speed Options
Description
55
70
90
Unit
ns
tELFL/tELFH
CE# to BYTE# Switching Low or High
Max
tFLQZ
BYTE# Switching Low to Output HIGH Z
Max
25
25
30
tFHQV
BYTE# Switching High to Output Active
Min
55
70
90
S29AL008D
5
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
CE#
OE#
BYTE#
BYTE#
Switching
from word
to byte
mode
DQ0–DQ14
tELFL
Data Output
(DQ0–DQ14)
Data Output
(DQ0–DQ7)
Address
Input
DQ15
Output
DQ15/A-1
tFLQZ
tELFH
BYTE#
BYTE#
Switching
from byte
to word
mode
Data Output
(DQ0–DQ7)
DQ0–DQ14
Address
Input
DQ15/A-1
Data Output
(DQ0–DQ14)
DQ15
Output
tFHQV
Figure 15.
BYTE# Timings for Read Operations
CE#
The falling edge of the last WE# signal
WE#
BYTE#
tSET
(tAS)
tHOLD (tAH)
Note: Refer to the Erase/Program Operations table for tAS and tAH specifications.
Figure 16.
June 16, 2005 S29AL008D_00A3
BYTE# Timings for Write Operations
S29AL008D
41
D a t a
S h e e t
AC Characteristics
Erase / Program Operations
Parameter
Speed Options
JEDEC
Std
Description
55
70
90
tAVAV
tWC
Write Cycle Time (Note 1)
55
70
90
tAVWL
tAS
Address Setup Time
0
tWLAX
tAH
Address Hold Time
45
tDVWH
tDS
Data Setup Time
tWHDX
tDH
Data Hold Time
tOES
Output Enable Setup Time
35
35
Unit
45
0
Min
0
Read Recovery Time Before Write
(OE# High to WE# Low)
0
ns
tGHWL
tGHWL
tELWL
tCS
CE# Setup Time
0
tWHEH
tCH
CE# Hold Time
0
tWLWH
tWP
Write Pulse Width
35
tWHWL
tWPH
Write Pulse Width High
30
tWHWH1
tWHWH1
Programming Operation (Note 2)
tWHWH2
tWHWH2
Sector Erase Operation (Note 2)
0.7
sec
tVCS
VCC Setup Time (Note 1)
50
µs
tRB
Recovery Time from RY/BY#
tBUSY
Byte
Word
5
Typ
Min
Program/Erase Valid to RY/BY# Delay
7
0
90
µs
ns
Notes:
1. Not 100% tested.
2. See Table , on page 49 for more information.
42
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
AC Characteristics
Program Command Sequence (last two cycles)
tAS
tWC
Addresses
Read Status Data (last two cycles)
555h
PA
PA
PA
tAH
CE#
tC
OE#
tWHWH1
tW
WE#
tWPH
tCS
tD
tD
A0h
Data
PD
Statu
tBUSY
DOUT
tRB
RY/BY#
VCC
tVCS
Notes:
1. PA = program address, PD = program data, DOUT is the true data at the program address.
2. Illustration shows device in word mode.
Figure 17.
June 16, 2005 S29AL008D_00A3
Program Operation Timings
S29AL008D
43
D a t a
S h e e t
AC Characteristics
Erase Command Sequence (last two cycles)
tAS
tWC
Addresses
Read Status Data
2AAh
SA
VA
VA
555h for chip erase
tA
CE#
tC
OE#
tW
WE#
tWP
tCS
tWHWH
tD
tD
Data
55h
In
Progress
30h
Complete
10 for Chip Erase
tBUSY
tRB
RY/BY#
tVC
VCC
Notes:
1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see Write Operation Status, on
page 27).
2. Illustration shows device in word mode.
Figure 18.
44
Chip/Sector Erase Operation Timings
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
AC Characteristics
tRC
Addresses
VA
VA
VA
tACC
tCE
CE#
tCH
tOE
OE#
tOEH
tDF
WE#
tOH
DQ7
DQ0–DQ6
Complement
Compleme
Status
Status
Valid Data
Tru
Valid Data
Tru
High
High
tBUS
RY/BY#
Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array
data read cycle.
Figure 19.
Data# Polling Timings (During Embedded Algorithms)
tRC
Addresses
VA
VA
VA
VA
tACC
tCE
CE#
tCH
tOE
OE#
tOEH
tDF
WE#
tOH
High
DQ6/DQ2
tBUS
Valid
Valid
(first read)
(second read)
Valid
Valid Data
(stops toggling)
RY/BY#
Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status
read cycle, and array data read cycle.
Figure 20.
June 16, 2005 S29AL008D_00A3
Toggle Bit Timings (During Embedded Algorithms)
S29AL008D
45
D a t a
S h e e t
AC Characteristics
Enter
Embedded
Erasing
Erase
Suspend
Erase
WE#
Enter Erase
Suspend Program
Erase
Resume
Erase
Suspend
Program
Erase Suspend
Read
Erase
Erase Suspend
Read
Erase
Complete
DQ6
DQ2
Note: The system may use CE# or OE# to toggle DQ2 and DQ6. DQ2 toggles only when read at an address within an
erase-suspended sector.
Figure 21.
Table 11.
DQ2 vs. DQ6
Temporary Sector Unprotect
Parameter
JEDEC
Std
tVIDR
tRSP
Description
VID Rise and Fall Time (See Note)
RESET# Setup Time for Temporary Sector
Unprotect
All Speed Options
Unit
Min
500
ns
Min
4
µs
Note: Not 100% tested.
12 V
RESET#
0 or 3 V
0 or 3 V
tVIDR
tVIDR
Program or Erase Command Sequence
CE#
WE#
tRSP
RY/BY#
Figure 22.
46
Temporary Sector Unprotect Timing Diagram
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
AC Characteristics
VID
VIH
RESET#
SA, A6,
Valid*
A1, A0
Valid*
Sector Protect/Unprotect
Data
60h
Valid*
Verify
60h
40h
Status
Sector Protect: 150 μs
Sector Unprotect: 15 ms
1 μs
CE#
WE#
OE#
* For sector protect, A6 = 0, A1 = 1, A0 = 0. For sector unprotect, A6 = 1, A1 = 1, A0 = 0.
Figure 23.
June 16, 2005 S29AL008D_00A3
Sector Protect/Unprotect Timing Diagram
S29AL008D
47
D a t a
S h e e t
AC Characteristics
Table 12.
Alternate CE# Controlled Erase/Program Operations
Parameter
Speed Options
JEDEC
Std
Description
55
70
90
tAVAV
tWC
Write Cycle Time (Note 1)
55
70
90
tAVEL
tAS
Address Setup Time
0
tELAX
tAH
Address Hold Time
45
tDVEH
tDS
Data Setup Time
tEHDX
tDH
Data Hold Time
tOES
Output Enable Setup Time
tGHEL
tGHEL
Read Recovery Time Before Write
(OE# High to WE# Low)
0
tWLEL
tWS
WE# Setup Time
0
tEHWH
tWH
WE# Hold Time
0
tELEH
tCP
CE# Pulse Width
35
tEHEL
tCPH
CE# Pulse Width High
30
tWHWH1
tWHWH1
Programming Operation
(Note 2)
tWHWH2
tWHWH2
Sector Erase Operation (Note 2)
35
35
Unit
45
0
Min
Byte
Word
0
8
Typ
16
1
ns
µs
sec
Notes:
1. Not 100% tested.
2. See Table , on page 49 for more information.
48
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
AC Characteristics
555 for programPA for program
2AA for erase SA for sector erase
555 for chip erase
Data# Polling
Addresses
PA
tWC
tAS
tAH
tWH
WE#
tGHEL
OE#
tWHWH1 or
tCP
CE#
tWS
tCPH
tBUS
tD
tD
DQ7
Data
tR
DOUT
A0 for program PD for program
55 for erase
30 for sector erase
10 for chip erase
RESET#
RY/BY#
Notes:
1. PA = program address, PD = program data, DQ7# = complement of the data written to the device, DOUT = data
written to the device.
2. Figure indicates the last two bus cycles of command sequence.
3. Word mode address used as an example.
Figure 24.
Alternate CE# Controlled Write Operation Timings
Erase and Programming Performance
Parameter
Typ Note 1
Max Note 2
Unit
Comments
Sector Erase Time
0.7
10
s
Chip Erase Time
14
Excludes 00h programming
prior to erasure
Byte Programming Time
7
210
µs
Word Programming Time
7
210
µs
s
Chip Programming Time
Byte Mode
8.4
25
s
Note 3
Word Mode
5.8
17
s
Excludes system level
overhead Note 5
Notes:
1. Typical program and erase times assume the following conditions: 25°C, 3.0 V VCC, 1,000,000 cycles. Additionally,
programming typicals assume checkerboard pattern.
June 16, 2005 S29AL008D_00A3
S29AL008D
49
D a t a
S h e e t
2. Under worst case conditions of 90°C, VCC = 2.7 V, 1,000,000 cycles.
3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most
bytes program faster than the maximum program times listed.
4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program
command. See Table 5, on page 25 for further information on command definitions.
6. The device has a guaranteed minimum erase and program cycle endurance of 1,000,000 cycles.
Table 13.
Latchup Characteristics
Description
Min
Max
Input voltage with respect to VSS on all pins except I/O pins
(including A9, OE#, and RESET#)
–1.0 V
12.5 V
Input voltage with respect to VSS on all I/O pins
–1.0 V
VCC + 1.0 V
–100 mA
+100 mA
VCC Current
Includes all pins except VCC. Test conditions: VCC = 3.0 V, one pin at a time.
Table 14.
TSOP, SO, and BGA Pin Capacitance
Parameter
Symbol
Parameter Description
Test Setup
CIN
Input Capacitance
VIN = 0
COUT
Output Capacitance
VOUT = 0
CIN2
Control Pin Capacitance
VIN = 0
Package
Typ
Max
TSOP, SO
6
7.5
BGA
4.2
5.0
TSOP, SO
8.5
12
BGA
5.4
6.5
TSOP, SO
7.5
9
BGA
3.9
4.7
Unit
pF
Notes:
1. Sampled, not 100% tested.
2. Test conditions TA = 25°C, f = 1.0 MHz.
50
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Physical Dimensions
TS 048—48-Pin Standard TSOP
Dwg rev AA; 10/99
* For reference only. BSC is an ANSI standard for Basic Space Centering.
June 16, 2005 S29AL008D_00A3
S29AL008D
51
D a t a
S h e e t
Physical Dimensions
VBK 048 - 48 Ball Fine-Pitch Ball Grid Array (FBGA) 8.15 x 6.15 mm
0.10 (4X)
D
D1
A
6
5
e
7
4
E
SE
E1
3
2
1
H
PIN A1
CORNER
INDEX MARK
10
6
B
G
F
fb
E
D
C
SD
B
A
A1 CORNER
7
f 0.08 M C
TOP VIEW
f 0.15 M C A B
BOTTOM VIEW
A
0.10 C
A2
SEATING PLANE
A1
C
0.08 C
SIDE VIEW
NOTES:
PACKAGE
VBK 048
JEDEC
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994.
N/A
2. ALL DIMENSIONS ARE IN MILLIMETERS.
6.15 mm x 8.15 mm NOM
PACKAGE
SYMBOL
MIN
NOM
MAX
A
---
---
1.00
A1
0.18
---
---
A2
0.62
---
0.76
3. BALL POSITION DESIGNATION PER JESD 95-1, SPP-010 (EXCEPT
AS NOTED).
NOTE
4.
OVERALL THICKNESS
BALL HEIGHT
8.15 BSC.
BODY SIZE
E
6.15 BSC.
BODY SIZE
D1
5.60 BSC.
BALL FOOTPRINT
E1
4.00 BSC.
MD
8
ROW MATRIX SIZE D DIRECTION
ME
6
ROW MATRIX SIZE E DIRECTION
N
48
0.35
---
N IS THE TOTAL NUMBER OF SOLDER BALLS.
BALL FOOTPRINT
BALL DIAMETER
e
0.80 BSC.
BALL PITCH
SD / SE
0.40 BSC.
SOLDER BALL PLACEMENT
---
6
DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL
DIAMETER IN A PLANE PARALLEL TO DATUM C.
7
SD AND SE ARE MEASURED WITH RESPECT TO DATUMS
A AND B AND DEFINE THE POSITION OF THE CENTER
SOLDER BALL IN THE OUTER ROW.
WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN
THE OUTER ROW PARALLEL TO THE D OR E DIMENSION,
RESPECTIVELY, SD OR SE = 0.000.
TOTAL BALL COUNT
0.43
REPRESENTS THE SOLDER BALL GRID PITCH.
SYMBOL "ME" IS THE BALL COLUMN MATRIX SIZE IN THE
"E" DIRECTION.
BODY THICKNESS
D
fb
e
5. SYMBOL "MD" IS THE BALL ROW MATRIX SIZE IN THE
"D" DIRECTION.
WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN
THE OUTER ROW, SD OR SE = e/2
8. NOT USED.
DEPOPULATED SOLDER BALLS
9. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED
BALLS.
10 A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK
MARK, METALLIZED MARK INDENTATION OR OTHER MEANS.
3338 \ 16-038.25b
52
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Physical Dimensions
SO 044—44-Pin Small Outline Package
Dwg rev AC; 10/99
June 16, 2005 S29AL008D_00A3
S29AL008D
53
D a t a
S h e e t
Revision Summary
Revision A (September 8, 2004)
Initial release
Revision A 1 (February 18, 2005)
Global
Updated Trademark
Ordering Information
Added Package type designator
Valid Combinations
Changed Package Type, Material, and Temperature Range designator
Under Package Descriptions, change SSOP to SOP
Revision A2 (June 1, 2005)
Global
Updated status from Advance Information to Preliminary data sheet.
Distinctive Characteristics
Updated manufactured process technology.
Updated high performance access time.
Added extended temperature range.
Added cycling endurance information.
Production Selector Guide
Added 55ns speed option and column.
Ordering Information
Added tube and tray packing types.
Added extended temperature range
Added model numbers.
Valid Combinations Table
Added speed option.
Added packing types.
Added model number.
Added note for this table.
Operating Range
Added extended temperature range information.
Test Conditions
Added 55ns speed option.
AC Characteristics
Read Operation Table
Added 55ns speed option.
Word/Byte Configuration Table
Added 55ns speed option.
54
S29AL008D
S29AL008D_00A3 June 16, 2005
D a t a
S h e e t
Erase/Program Operation Table
Added 55ns speed option.
Alternate CE# Controlled Erase/Program Operation Table
Added 55ns speed option.
Erase and Programming Performance
Changed Byte Programing Time values for Typical and Maximum.
Revision A3 (June 16, 2005)
Changed from Preliminary to full Data Sheet.
Updated Valid Combinations table.
Colophon
The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary
industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that
includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal
injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control,
medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and
artificial satellite). Please note that Spansion will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures
by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other
abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under
the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity will be required for export of those products.
Trademarks and Notice
The contents of this document are subject to change without notice. This document may contain information on a Spansion LLC product under development
by Spansion LLC. Spansion LLC reserves the right to change or discontinue work on any product without notice. The information in this document is provided
as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose, merchantability, non-infringement
of third-party rights, or any other warranty, express, implied, or statutory. Spansion LLC assumes no liability for any damages of any kind arising out of the
use of the information in this document.
Copyright ©2004-2005 Spansion LLC. All rights reserved. Spansion, the Spansion logo, and MirrorBit are trademarks of Spansion LLC. Other company and
product names used in this publication are for identification purposes only and may be trademarks of their respective companies
June 16, 2005 S29AL008D_00A3
S29AL008D
55