SPANSION S29CD016J0MDGH117

S29CD016J/S29CL016J
Known Good Die
16 Megabit (512k x 32-Bit) CMOS 2.6 or 3.3 Volt-only
Burst Mode, Dual Boot,
Simultaneous Read/Write Flash Memory
Supplement (Advance Information)
General Description
The Spansion S29CD016J and S29CL016J devices are Floating Gate products fabricated in 110 nm process technology.
These burst mode Flash devices are capable of performing simultaneous read and write operations with zero latency on two
separate banks. These products can operate up to 56 MHz and use a single VCC of 2.5 V to 2.75 V (S29CD-J) or 3.0 V to 3.6 V
(S29CL-J) that make them ideal for today’s demanding automotive applications.
Distinctive Characteristics
„ Single 2.6 V (S29CD-J) or 3.3 V (S29CL-J) for read/program/
erase
„ Cycling Endurance: 100,000 write cycles per sector (typical)
„ 110 nm Floating Gate Technology
„ Supports Common Flash Interface (CFI)
„ Simultaneous Read/Write operation with zero latency
„ Persistent and Password methods of Advanced Sector
Protection
„ X32 Data Bus
„ Dual Boot Sector Configuration (top and bottom)
„ Command set compatible with JECEC (42.4) standard
„ Unlock Bypass program command to reduce programming
time
„ Flexible Sector Architecture
– CD016J & CL016J: Eight 2K Double word, Thirty-two 16K Double
word, and Eight 2K Double Word sectors
„ VersatileI/O™ control (1.65 V to VCC)
„ Write operation status bits indicate program and erase
operation completion
„ Hardware (WP#) protection of two outermost sectors in the
large bank
„ Programmable Burst Interface
– Linear for 2, 4, and 8 double word burst with or without wrap around
„ Secured Silicon Sector that can be either factory or customer
locked
„ 20 year data retention (typical)
„ Ready/Busy (RY/BY#) output indicates data available to
system
„ Suspend and Resume commands for Program and Erase
Operation
Performance Characteristics
Read Access Times
Speed Option (MHz)
Max Asynch. Access Time, ns (tACC)
Current Consumption (Max values)
56
40
Continuous Burst Read @ 56 MHz
90 mA
64
67
Program
50 mA
Max Synch. Latency, ns (tIACC)
64
67
Erase
50 mA
Max Synch. Burst Access, ns (tBACC)
10
17
Standby Mode
150 µA
Max CE# Access Time, ns (tCE)
69
71
Max OE# Access time, ns (tOE)
22
22
Publication Number S29CD016J-CL016J_KGD_SP
Typical Program and Erase Times
Double Word Programming
18 µs
Sector Erase
1.0 s
Revision A
Amendment 2
Issue Date September 20, 2006
This document contains information on one or more products under development at Spansion Inc. The information is intended to help you evaluate this product. Do not design in
this product without contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed product without notice.
Supplement
(Advance
I nfor mation )
Table of Contents
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Distinctive Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
S29CD/CL016J Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.
Die Photograph. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.
Die Pad Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.
Pad Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1
Valid Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.
Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.1
Surftape Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2
Waffle Pack Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6.
Product Test Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8.
Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9.
Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
10.
Manufacturing Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
11.
Special Handling Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
11.1 Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
11.2 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
12.
DC Characteristics for KGD Devices at 145°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
13.
Terms and Conditions of Sale for Spansion Non-Volatile Memory Die. . . . . . . . . . . . . . . . . . . . . 14
14.
Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
List of Figures
Figure 6.1
Figure 7.1
Figure 7.2
Spansion KGD Product Test Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Maximum Negative Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Maximum Positive Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
List of Tables
Table 3.1
Table 12.1
2
Pads Relative To Die Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
DC Characteristics, CMOS Compatible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
S29CD016J/S29CL016J Known Good Die
Revision A2 September 20, 2006
Supplement
(Advan ce
Info r m atio n)
S29CD/CL016J Features
The S29CD016J & S29CL016J Flash devices are burst mode, dual boot, simultaneous read/write Flash
memories with VersatileI/O™ manufactured on 110 nm process technology.
The S29CD016J is a 16 megabit, 2.6 volt-only, single-power-supply, burst mode Flash memory device that
can be configured for 524,288 double words. The S29CL016J is the 3.3 volt-only version of that device. Both
devices can be programmed in standard EPROM programmers.
To eliminate bus contention, each device has separate chip enable (CE#), write enable (WE#) and output
enable (OE#) controls. Additional control inputs are required for synchronous burst operations: Load Burst
Address Valid (ADV#), and Clock (CLK).
Each device requires only a single 2.6 volt-only (2.50 V – 2.75 V) or 3.3 volt-only (3.00 V – 3.60 V) for both
read and write functions. A 12.0-volt VPP is not required for program or erase operations, although an
acceleration pin is available if faster programming performance is required.
The device is entirely command set compatible with the JEDEC single-power-supply Flash standard. The
software command set is compatible with the command sets of the 5 V Am29F and 3 V Am29LV Flash
families. Commands are written to the command register using standard micro-processor write timing.
Register contents serve as inputs to an internal state-machine that controls the erase and programming
circuitry. Write cycles also internally latch addresses and data needed for the programming and erase
operations. Reading data out of the device is similar to reading from other Flash or EPROM devices.
The Unlock Bypass mode facilitates faster programming times by requiring only two write cycles to program
data instead of four.
The Simultaneous Read/Write architecture provides simultaneous operation by dividing the memory space
into two banks. The device can begin programming or erasing in one bank, and then simultaneously read
from the other bank, with zero latency. This releases the system from waiting for the completion of program or
erase operations.
The device provides a 256-byte Secured Silicon Sector with an one-time-programmable (OTP) mechanism.
In addition, the device features several levels of sector protection, which can disable both the program and
erase operations in certain sectors or sector groups: Persistent Sector Protection is a command sector
protection method that replaces the old 12 V controlled protection method; Password Sector Protection is a
highly sophisticated protection method that requires a password before changes to certain sectors or sector
groups are permitted; WP# Hardware Protection prevents program or erase in the two outermost 8 Kbytes
sectors of the larger bank.
The device defaults to the Persistent Sector Protection mode. The customer must then choose if the
Standard or Password Protection method is most desirable. The WP# Hardware Protection feature is always
available, independent of the other protection method chosen.
The VersatileI/O™ (VCCQ) feature allows the output voltage generated on the device to be determined based
on the VIO level. This feature allows this device to operate in the 1.8 V I/O environment, driving and receiving
signals to and from other 1.8 V devices on the same bus.
The host system can detect whether a program or erase operation is complete by observing the RY/BY# pin,
by reading the DQ7 (Data# Polling), or DQ6 (toggle) status bits. After a program or erase cycle has been
completed, the device is ready to read array data or accept another command.
The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the
data contents of other sectors. The device is fully erased when shipped from the factory.
Hardware data protection measures include a low VCC detector that automatically inhibits write operations
during power transitions. The password and software sector protection feature disables both program and
erase operations in any combination of sectors of memory. This can be achieved in-system at VCC level.
The Program/Erase Suspend/Erase Resume feature enables the user to put erase on hold for any period of
time to read data from, or program data to, any sector that is not selected for erasure. True background erase
can thus be achieved.
The hardware RESET# pin terminates any operation in progress and resets the internal state machine to
reading array data.
September 20, 2006 Revision A2
S29CD016J/S29CL016J Known Good Die
3
Supplement
(Advance
I nfor mation )
The device offers two power-saving features. When addresses have been stable for a specified amount of
time, the device enters the automatic sleep mode. The system can also place the device into the standby
mode. Power consumption is greatly reduced in both these modes.
Spansion Flash technology combines years of Flash memory manufacturing experience to produce the
highest levels of quality, reliability and cost effectiveness. The device electrically erases all bits within a sector
simultaneously via Fowler-Nordheim tunnelling. The data is programmed using hot electron injection.
1. Die Photograph
4
S29CD016J/S29CL016J Known Good Die
Revision A2 September 20, 2006
Supplement
(Advan ce
Info r m atio n)
2. Die Pad Locations
30
20
25
29
28
15
10
8
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
30
31
6
7
31
32
33
5
34
35
4
Y
35
36
5
3
2
37
1
74
1
X
38
73
74
39
40
72
40
41
42
71
43
70
44
69
45
45
49
46
47
47
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
70
68
48
50
55
60
65
69
Logo
September 20, 2006 Revision A2
S29CD016J/S29CL016J Known Good Die
5
Supplement
(Advance
I nfor mation )
3. Pad Description
Table 3.1 Pads Relative To Die Center (Sheet 1 of 2)
Pad Description – Coordinates are Relative to Die Center
Mils
6
µm
Pad
Signal
X
Y
X
Y
1
VSS
87.381
3.347
2219.485
85.016
2
VCC
87.381
8.031
2219.485
203.994
3
CE#
87.381
12.892
2219.485
327.456
4
OE#
87.381
17.556
2219.485
445.921
5
WE#
87.381
22.22
2219.485
564.386
6
WP#
87.381
27.039
2219.485
686.793
7
IND/WAIT#
88.346
39.741
2243.986
1009.432
8
DQ(16)
70.562
46.96
1792.27
1192.773
9
DQ(17)
65.797
46.96
1671.24
1192.773
10
DQ(18)
57.691
46.96
1465.356
1192.773
11
DQ(19)
52.926
46.96
1344.326
1192.773
12
VCCQ
46.4
46.96
1178.57
1192.773
13
VSS
41.738
46.96
1060.153
1192.773
14
DQ(20)
35.235
46.96
894.957
1192.773
15
DQ(21)
30.47
46.96
773.927
1192.773
16
DQ(22)
22.364
46.96
568.043
1192.773
17
DQ(23)
17.599
46.96
447.013
1192.773
18
DQ(24)
–0.093
46.96
–2.356
1192.773
19
DQ(25)
–4.858
46.96
–123.386
1192.773
20
DQ(26)
–12.963
46.96
–329.27
1192.773
21
DQ(27)
–17.728
46.96
–450.3
1192.773
22
VCCQ
–24.254
46.96
–616.056
1192.773
23
VSS
–28.916
46.96
–734.474
1192.773
24
DQ(28)
–35.42
46.96
–899.669
1192.773
25
DQ(29)
–40.185
46.96
–1020.699
1192.773
26
DQ(30)
–48.291
46.96
–1226.583
1192.773
27
DQ(31)
–53.056
46.96
–1347.613
1192.773
28
A0
–69.006
49.02
–1752.741
1245.108
29
A1
–73.77
49.02
–1873.771
1245.108
30
A2
–78.333
49.02
–1989.671
1245.108
31
A3
–88.473
41.504
–2247.216
1054.196
32
A4
–88.473
36.941
–2247.216
938.296
33
A5
–88.473
32.176
–2247.216
817.266
34
A6
–88.473
27.613
–2247.216
701.366
35
A7
–88.473
22.848
–2247.216
580.336
36
A8
–88.473
18.285
–2247.216
464.436
37
VSS
–88.473
13.402
–2247.216
340.414
38
ACC
–88.473
8.245
–2247.216
209.418
39
VCC
–88.473
–11.899
–2247.216
–302.224
40
A9
–88.473
–17
–2247.216
–431.794
41
A10
–88.473
–21.905
–2247.216
–556.387
S29CD016J/S29CL016J Known Good Die
Revision A2 September 20, 2006
Supplement
(Advan ce
Info r m atio n)
Table 3.1 Pads Relative To Die Center (Sheet 2 of 2)
Pad Description – Coordinates are Relative to Die Center
Mils
September 20, 2006 Revision A2
µm
Pad
Signal
X
Y
X
Y
42
A11
–88.473
–26.468
–2247.216
–672.287
43
A12
–88.473
–31.233
–2247.216
–793.317
44
A13
–88.473
–35.796
–2247.216
–909.217
45
A14
–88.473
–40.561
–2247.216
–1030.247
46
A15
–88.473
–45.124
–2247.216
–1146.147
47
A16
–78.333
–49.192
–1989.671
–1249.469
48
A17
–73.77
–49.192
–1873.771
–1249.469
49
A18
–69.006
–49.192
–1752.741
–1249.469
50
DQ(0)
–53.056
–47.131
–1347.613
–1197.133
51
DQ(1)
–48.291
–47.131
–1226.583
–1197.133
52
DQ(2)
–40.185
–47.131
–1020.699
–1197.133
53
DQ(3)
–35.42
–47.131
–899.669
–1197.133
54
VCCQ
–28.894
–47.131
–733.913
–1197.133
55
VSS
–24.232
–47.131
–615.496
–1197.133
56
DQ(4)
–17.728
–47.131
–450.3
–1197.133
57
DQ(5)
–12.963
–47.131
–329.27
–1197.133
58
DQ(6)
–4.858
–47.131
–123.386
–1197.133
59
DQ(7)
–0.093
–47.131
–2.356
–1197.133
60
DQ(8)
17.599
–47.131
447.013
–1197.133
61
DQ(9)
22.364
–47.131
568.043
–1197.133
62
DQ(10)
30.47
–47.131
773.927
–1197.133
63
DQ(11)
35.235
–47.131
894.957
–1197.133
64
VCCQ
41.76
–47.131
1060.713
–1197.133
65
VSS
46.422
–47.131
1179.131
–1197.133
66
DQ(12)
52.926
–47.131
1344.326
–1197.133
67
DQ(13)
57.691
–47.131
1465.356
–1197.133
68
DQ(14)
65.797
–47.131
1671.24
–1197.133
69
DQ(15)
70.562
–47.131
1792.27
–1197.133
70
VCCQ
87.381
–42.383
2219.485
–1076.54
71
RESET#
87.381
–36.499
2219.485
–927.067
72
CLK
87.381
–31.394
2219.485
–797.402
73
RY/BY#
88.346
–19.018
2243.986
–483.066
74
ADV#
87.381
–11.386
2219.485
–289.199
S29CD016J/S29CL016J Known Good Die
7
Supplement
4.
(Advance
I nfor mation )
Ordering Information
The order number (Valid Combination) is formed by the following:
S29CD016J
S29CL016J
0J
D
E
I
00
4
PACKING TYPE
4 = Surf Tape (2500 per reel)
7 = Waffle Pack (42 per waffle pack tray)
ADDITIONAL ORDERING OPTIONS
15th Character – S29CD016J only:
0 = 7E, 08, 01/00 Autoselect ID
1 = 7E, 36, 01/00 Autoselect ID
15th Character – S29CL016J only:
0 = 7E, 46, 01/00 Autoselect ID
16th Character – Top or Bottom Boot:
1 = Bottom Boot with Simultaneous Operation
3 = Bottom Boot with No Simultaneous Operation
TEMPERATURE RANGE
H = Hot (–40°C to +145°C)
DIE THICKNESS
G = 500 µm
PACKAGE TYPE
D = Die
CLOCK FREQUENCY
10th Character - Initial Burst Access Delay
0 = 5-1-1-1, 6-1-1-1, and above
1 = 4-1-1-1
11h Character - Frequency
J = 40 Mhz
M = 56 Mhz
DEVICE NUMBER/DESCRIPTION
S29CD016J/S29CL016J
16 Megabit (512K x 32-Bit) CMOS 2.6 or 3.3 Volt-only Burst Mode,
Dual Boot, Simultaneous Read/Write Flash Memory
Manufactured on 110 nm Floating Gate Technology
S29CL016J/S29CL016J Valid Combinations
S29CD016J
S29CL016J
4.1
OJ, 1J, OM
1M
01, 03, 11, 13
D
G
H
OJ, 1J, OM, 1M
03, 13
01, 03
Valid Combinations
Valid Combinations list configurations planned to be supported in volume for this device. Consult your local
sales office to confirm availability of specific valid combinations and to 0c\\heck on newly released
combinations.
8
S29CD016J/S29CL016J Known Good Die
Revision A2 September 20, 2006
Supplement
(Advan ce
Info r m atio n)
5. Packaging Information
5.1
Surftape Packaging
Direction of Feed
12 mm
Orientation
relative to
leading edge of
tape and reel
September 20, 2006 Revision A2
Spansion
logo location
S29CD016J/S29CL016J Known Good Die
9
Supplement
5.2
(Advance
I nfor mation )
Waffle Pack Packaging
Orientation
relative to
top-left corner
of Waffle Pack
cavity plate
Spansion Logo
Location
6. Product Test Flow
Figure 6.1 provides an overview of Spansion’s Known Good Die test flow. For more detailed information, refer
to the S29CD016J/S29CL016J product qualification database. Spansion implements quality assurance
procedures throughout the product test flow. These QA procedures also allow Spansion to produce KGD
products without requiring or implementing burn-in. In addition, an off-line quality monitoring program (QMP)
further guarantees Spansion quality standards are met on Known Good Die products.
10
S29CD016J/S29CL016J Known Good Die
Revision A2 September 20, 2006
Supplement
(Advan ce
Info r m atio n)
Figure 6.1 Spansion KGD Product Test Flow
Wafer Sort 1
Bake
24 hours at 250°C
Electronic Marking
Step 1: Wafer sort,
test 1 & 2 information
Wafer Sort 2
Electronic Marking
Step 2: Final class or
KGD test information
& device speed
Wafer Sort 3
High Temperature
Packaging for
Shipment
DC Parameters
Functionality
Programmability
Erasability
Data Retention
DC Parameters
Functionality
Programmability
Erasability
DC Parameters
Functionality
Programmability
Erasability
Speed
Incoming Inspection
Wafer Saw
Die Separation
100% Visual Inspection
Die Pack
Shipment
Electronic marking is programmed into every KGD for the purpose of traceability. The electronic marking
contains wafer lot number, wafer number of origin, die location on the wafer, mask revision, test program
revision, test dates, and speed grade. Figure 6.1 illustrates the steps where specific electronic marking
information is programmed. For more information regarding electronic marking, reference the S29CD016J
Electronic Marking Data Sheet Supplement.
September 20, 2006 Revision A2
S29CD016J/S29CL016J Known Good Die
11
Supplement
7.
(Advance
I nfor mation )
Absolute Maximum Ratings
Parameter
Rating
Storage Temperature
–65°C to +150°C
Ambient Temperature with Power Applied
–65°C to +145°C
VCC, VIO (Note 1)
S29CD016J
–0.5 V to + 3.0 V
VCC, VIO (Note 1)
S29CL016J
–0.5 V to + 3.6 V
ACC, A9, OE#, and RESET# (Note 2)
–0.5 V to +13.0 V
Address, Data, Control Signals
(with the exception of CLK) (Note 1)
–0.5 V to +3.6 V
All other pins (Note 1)
–0.5 V to +3.6 V
Output Short Circuit Current (Note 3)
200 mA
Notes
1. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input at I/O pins may overshoot VSS to –2.0 V for periods of
up to 20 ns. See Figure 7.1. Maximum DC voltage on output and I/O pins is 3.0 V. During voltage transitions output pins may overshoot to
VCC + 2.0 V for periods up to 20 ns. See Figure 9.
2. Minimum DC input voltage on pins ACC, A9, OE#, and RESET# is –0.5 V. During voltage transitions, A9, OE#, and RESET# may
overshoot VSS to –2.0 V for periods of up to 20 ns. See Figure 7.2. Maximum DC input voltage on pin A9 and OE# is +13.0 V which may
overshoot to 13.7 V for periods up to 20 ns.
3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second.
4. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only;
functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is
not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability.
Figure 7.1 Maximum Negative Overshoot Waveform
20 ns
20 ns
+0.8 V
–0.5 V
–2.0 V
20 ns
Figure 7.2 Maximum Positive Overshoot Waveform
20 ns
V CC
+2.0 V
V CC
+0.5 V
2.0 V
20 ns
20 ns
8. Operating Ranges
Parameter
Rating
Ambient Temperature (TA), Hot Range
VCC Supply Voltage for regulated voltage range
–40°C to +145°C
CD016J
2.5 V to 2.75 V
CL016J
3.0 V to 3.6 V
VIO Supply Voltage
1.65 V to VCC
Note
Operating ranges define those limits between which the functionality of the device is guaranteed.
12
S29CD016J/S29CL016J Known Good Die
Revision A2 September 20, 2006
Supplement
(Advan ce
Info r m atio n)
9. Physical Specifications
Specification
Value
Die Dimensions
4.77 x 2.83 mm
Die Thickness
500 µm
Bond Pad Size
86 x 86 µm
Pad Area Free of Passivation
5,776 µm2
Pads Per Die
74
Bond Pad Metalization
Al/Cu
Si02/SiN
Passivation
10. Manufacturing Information
Item Description
Location/Data
Manufacturing Location
Fab 25, TX
Test Location
PNG
Shipment Preparation Location
Penang, Malaysia
Manufacturing ID (Bottom Boot)
98P05AB
Fabrication Process
CS69S
Die Revision
1
11. Special Handling Instructions
11.1
Processing
Do not expose KGD products to ultraviolet light or process them at temperatures greater than 250°C. Failure
to adhere to these handling instructions will result in irreparable damage to the devices. For best yield,
Spansion recommends assembly in a Class 10K clean room with 30% to 60% relative humidity.
11.2
Storage
Store at a maximum temperature of 30°C in a nitrogen-purged cabinet or
vacuum-sealed bag. Observe all standard ESD handling procedures.
12. DC Characteristics for KGD Devices at 145°C
Table 12.1 DC Characteristics, CMOS Compatible
Parameter
Description
Test Condition
Min
Typ
Max
Unit
10
mA
50
mA
ICC1
VCC Active Asynchronous Read
Current
CE# = VIL, OE#=VIL
ICC3
VCC Active Program Current
CE# = VIL, OE#=VIL, ACC = VIH
ICC5 (Note 1)
VCC Standby Current (CMOS)
VCC = VCCMAX, CE# = VCC ± 0.3 V
250
µA
ICC7 (Note 1)
VCC Reset Current
Reset = VIL
250
µA
ICC8 (Note 1)
Automatic Sleep Mode Current
VIH = VCC ± 0.3 V, VIL = VSS ± 0.3 V
250
µA
September 20, 2006 Revision A2
S29CD016J/S29CL016J Known Good Die
1 MHz
40
13
Supplement
(Advance
I nfor mation )
13. Terms and Conditions of Sale for Spansion Non-Volatile Memory Die
All transactions relating to unpackaged die under this agreement shall be subject to Spansion’s standard
terms and conditions of sale, or any revisions thereof, which revisions Spansion reserves the right to make at
any time and from time to time. In the event of conflict between the provisions of Spansion’s standard terms
and conditions of sale and this agreement, the terms of this agreement shall be controlling.
Spansion warrants its manufactured unpackaged die whether shipped to customer in individual dice or wafer
form (“Known Good Die,” “KGD”, “Die,” “Known Good Wafer”, “KGW”, or Wafer(s)) will meet Spansion's
published specifications and against defective materials or workmanship for a period of one (1) year from
date of shipment.
This limited warranty does not extend beyond the first purchaser of said Die or Wafer(s).
Buyer assumes full responsibility to ensure compliance with the appropriate handling, assembly and
processing of KGD or KGW (including but not limited to proper Die preparation, Die attach, backgrinding,
singulation, wire bonding and related assembly and test activities), and compliance with all guidelines set
forth in Spansion's specifications for KGD or KGW, and Spansion assumes no responsibility for
environmental effects on KGD or KGW or for any activity of Buyer or a third party that damages the Die or
Wafer(s) due to improper use, abuse, negligence, improper installation, improper backgrinding, improper
singulation, accident, loss, damage in transit, or unauthorized repair or alteration by a person or entity other
than Spansion (“Limited Warranty Exclusions”)
The liability of Spansion under this limited warranty is limited, at Spansion's option, solely to repair the Die or
Wafer(s), to send replacement Die or Wafer(s), or to make an appropriate credit adjustment or refund in an
amount not to exceed the original purchase price actually paid for the Die or Wafer(s) returned to Spansion,
provided that: (a) Spansion is promptly notified by Buyer in writing during the applicable warranty period of
any defect or nonconformity in the Die or Wafer(s); (b) Buyer obtains authorization from Spansion to return
the defective Die or Wafer(s); (c) the defective Die or Wafer(s) is returned to Spansion by Buyer in
accordance with Spansion's shipping instructions set forth below; and (d) Buyer shows to Spansion's
satisfaction that such alleged defect or nonconformity actually exists and was not caused by any of the
above-referenced Warranty Exclusions. Buyer shall ship such defective Die or Wafer(s) to Spansion via
Spansion's carrier, collect. Risk of loss will transfer to Spansion when the defective Die or Wafer(s) is
provided to Spansion's carrier. If Buyer fails to adhere to these warranty returns guidelines, Buyer shall
assume all risk of loss and shall pay for all freight to Spansion's specified location. The aforementioned
provisions do not extend the original limited warranty period of any Die or Wafer(s) that has either been
replaced by Spansion.
THIS LIMITED WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, THE
IMPLIED WARRANTY OF MERCHANTABILITY OR NONINFRINGEMENT AND OF ALL OTHER
OBLIGATIONS OR LIABILITIES ON Spansion's PART, AND IT NEITHER ASSUMES NOR AUTHORIZES
ANY OTHER PERSON TO ASSUME FOR Spansion ANY OTHER LIABILITIES. THE FOREGOING
CONSTITUTES THE BUYER'S SOLE AND EXCLUSIVE REMEDY FOR THE FURNISHING OF
DEFECTIVE OR NON CONFORMING KNOWN GOOD DIE OR KNOWN GOOD WAFER(S) AND Spansion
SHALL NOT IN ANY EVENT BE LIABLE FOR INCREASED MANUFACTURING COSTS, DOWNTIME
COSTS, DAMAGES RELATING TO BUYER'S PROCUREMENT OF SUBSTITUTE DIE OR WAFER(S) (i.e.,
“COST OF COVER”), LOSS OF PROFITS, REVENUES OR GOODWILL, LOSS OF USE OF ORDAMAGE
TO ANY ASSOCIATED EQUIPMENT, OR ANY OTHER INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES BY REASON OF THE FACT THAT SUCH KNOWN GOOD DIE OR KNOWN
GOOD WAFER(S) SHALL HAVE BEEN DETERMINED TO BE DEFECTIVE OR NON CONFORMING.
Buyer agrees that it will make no warranty representations to its customers which exceed those given by
Spansion to Buyer unless and until Buyer shall agree to indemnify Spansion in writing for any claims which
exceed Spansion's limited warranty. Known Good Die or Known Good Wafer(s) are not designed or
authorized for use as components in life support appliances, devices or systems where malfunction of the Die
or Wafer(s) can reasonably be expected to result in a personal injury. Buyer's use of Known Good Die or
Known Good Wafer(s) for use in life support applications is at Buyer's own risk and Buyer agrees to fully
indemnify Spansion for any damages resulting in such use or sale.
Known Good Die or Known Good Wafer are not designed or authorized for use as components in life support
appliances, devices or systems where malfunction of the die or wafer can reasonably be expected to result in
a personal injury. Buyer's use of Known Good Die or Known Good Wafer for use in life support applications is
at Buyer's own risk and Buyer agrees to fully indemnify Spansion for any damages resulting in such use or
sale.
14
S29CD016J/S29CL016J Known Good Die
Revision A2 September 20, 2006
Supplement
(Advan ce
Info r m atio n)
14. Revision Summary
Section
Description
Revision A0 (December 23, 2005)
Initial release.
Revision A1 (August 16, 2006)
Die Pad Locations
Corrected die pad locations figure.
Revision A2 (September 20, 2006)
Global
Added S29CL016J information. Deleted emboss tape packing type. Deleted industrial and extended
temperature ranges.
Colophon
The products described in this document are designed, developed and manufactured as contemplated for general use, including without
limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as
contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the
public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility,
aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for
any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion will not be liable to
you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor
devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design
measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal
operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under
the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country,
the prior authorization by the respective government entity will be required for export of those products.
Trademarks and Notice
The contents of this document are subject to change without notice. This document may contain information on a Spansion product under
development by Spansion. Spansion reserves the right to change or discontinue work on any product without notice. The information in this
document is provided as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose,
merchantability, non-infringement of third-party rights, or any other warranty, express, implied, or statutory. Spansion assumes no liability for any
damages of any kind arising out of the use of the information in this document.
Copyright © 2005–2006 Spansion Inc. All Rights Reserved. Spansion, the Spansion logo, MirrorBit, ORNAND, HD-SIM, and combinations
thereof are trademarks of Spansion Inc. Other names are for informational purposes only and may be trademarks of their respective owners.
September 20, 2006 Revision A2
S29CD016J/S29CL016J Known Good Die
15