INFINEON SAK-XC2264

D a t a S h e e t, V 0. 1 , F e b . 2 0 0 7
XC226x
t V
er
si
on
af
Dr
P
re
li
m
in
ar
y
1 6 / 3 2 - B i t S i n g l e -C h i p M i c r o c o n t r o l l e r w i t h
32-Bit Performance
M i c r o c o n t r o l l e rs
Edition 2007-02
Published by
Infineon Technologies AG
81726 München, Germany
© Infineon Technologies AG 2007.
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics (“Beschaffenheitsgarantie”). With respect to any examples or hints given herein, any typical values
stated herein and/or any information regarding the application of the device, Infineon Technologies hereby
disclaims any and all warranties and liabilities of any kind, including without limitation warranties of noninfringement of intellectual property rights of any third party.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
D a t a S h e e t, V 0. 1 , F e b . 2 0 0 7
XC226x
t V
er
si
on
af
Dr
P
re
li
m
in
ar
y
1 6 / 3 2 - B i t S i n g l e -C h i p M i c r o c o n t r o l l e r w i t h
32-Bit Performance
M i c r o c o n t r o l l e rs
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
XC226x
Revision History: V0.1, 2007-02
Previous Version(s):
None
Page
Subjects (major changes since last revision)
We Listen to Your Comments
Any information within this document that you feel is wrong, unclear or missing at all?
Your feedback will help us to continuously improve the quality of this document.
Please send your proposal (including a reference to this document) to:
[email protected]
Data Sheet
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table of Contents
Table of Contents
1
Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2
2.1
General Device Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Pin Configuration and Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
3.17
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Subsystem and Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Bus Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Central Processing Unit (CPU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
On-Chip Debug Support (OCDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capture/Compare Unit (CAPCOM2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capture/Compare Units CCU6x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Purpose Timer (GPT12E) Unit . . . . . . . . . . . . . . . . . . . . . . . . . . .
Real Time Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A/D Converters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Universal Serial Interface Channel Modules (USIC) . . . . . . . . . . . . . . . . .
MultiCAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
29
32
33
35
41
42
45
47
51
53
54
56
58
59
60
62
63
4
4.1
4.2
4.2.1
4.2.2
4.2.3
4.3
4.4
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
Electrical Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC Parameters for Upper Voltage Area . . . . . . . . . . . . . . . . . . . . . . . .
DC Parameters for Lower Voltage Area . . . . . . . . . . . . . . . . . . . . . . . .
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog/Digital Converter Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Definition of Internal Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
On-chip Flash Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Clock Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Testing Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
66
70
71
73
75
78
81
81
84
85
86
87
5
5.1
5.2
5.3
Package and Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flash Memory Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
95
95
97
98
Data Sheet
3
V0.1, 2007-02
Draft Version
Preliminary
16/32-Bit Single-Chip Microcontroller with 32-Bit
Performance
XC2000 Family
1
XC226x
Summary of Features
For a quick overview or reference, the XC226x’s properties are listed here in a
condensed way.
•
•
•
•
•
•
High Performance 16-bit CPU with 5-Stage Pipeline
– 15 ns Instruction Cycle Time at 66 MHz CPU Clock (Single-Cycle Execution)
– 1-Cycle 32-bit Addition and Subtraction with 40-bit result
– 1-Cycle Multiplication (16 × 16 bit)
– 1-Cycle Multiply-and-Accumulate (MAC) Instructions
– Background Division (32 / 16 bit) in 21 Cycles
– Enhanced Boolean Bit Manipulation Facilities
– Zero-Cycle Jump Execution
– Additional Instructions to Support HLL and Operating Systems
– Register-Based Design with Multiple Variable Register Banks
– Fast Context Switching Support with Two Additional Local Register Banks
– 16 Mbytes Total Linear Address Space for Code and Data
– 1024 Bytes On-Chip Special Function Register Area (C166 Family Compatible)
16-Priority-Level Interrupt System with up to 87 Sources, Selectable External Inputs
for Interrupt Generation and Wake-Up, Sample-Rate down to 15 ns
8-Channel Interrupt-Driven Single-Cycle Data Transfer Facilities via
Peripheral Event Controller (PEC), 24-Bit Pointers Cover Total Address Space
Clock Generation from Internal or External Clock Sources,
via on-chip PLL or via Prescaler
On-Chip Memory Modules
– 1 Kbyte On-Chip Stand-By RAM (SBRAM)
– 2 Kbytes On-Chip Dual-Port RAM (DPRAM)
– 16 Kbytes On-Chip Data SRAM (DSRAM)
– Up to 64 Kbytes On-Chip Program/Data SRAM (PSRAM)
– Up to 768 Kbytes On-Chip Program Memory (Flash Memory)
On-Chip Peripheral Modules
– Two Synchronizable A/D Converters with a total of 16 Channels, 10-bit Resolution,
Conversion Time down to 1.2 µs, Optional Data Preprocessing (Data Reduction,
Range Check)
– 16-Channel General Purpose Capture/Compare Unit (CAPCOM2)
– Up to four Capture/Compare Units for flexible PWM Signal Generation (CCU6x)
– Multi-Functional General Purpose Timer Unit with 5 Timers
– Six Serial Interface Channels to be used as UART, LIN, High-Speed Synchronous
Channel (SPI/QSPI), IIC Bus Interface (10-bit addressing, 400 kbit/s), IIS Interface
Data Sheet
4
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
•
•
•
•
•
•
•
•
•
Summary of Features
– On-Chip MultiCAN Interface (Rev. 2.0B active) with up to 128 Message Objects
(Full CAN/Basic CAN) on up to 5 CAN Nodes and Gateway Functionality
– On-Chip Real Time Clock
Up to 12 Mbytes External Address Space for Code and Data
– Programmable External Bus Characteristics for Different Address Ranges
– Multiplexed or Demultiplexed External Address/Data Buses
– Selectable Address Bus Width
– 16-Bit or 8-Bit Data Bus Width
– Four Programmable Chip-Select Signals
Single Power Supply from 3.0 V to 5.5 V
Power Reduction Modes with Flexible Power Management
Programmable Watchdog Timer and Oscillator Watchdog
Up to 75 General Purpose I/O Lines
On-Chip Bootstrap Loader
Supported by a Large Range of Development Tools like C-Compilers, MacroAssembler Packages, Emulators, Evaluation Boards, HLL-Debuggers, Simulators,
Logic Analyzer Disassemblers, Programming Boards
On-Chip Debug Support via JTAG Interface
100-Pin Green LQFP Package, 0.5 mm (19.7 mil) pitch
Ordering Information
The ordering code for Infineon microcontrollers provides an exact reference to the
required product. This ordering code identifies:
•
•
the derivative itself, i.e. its function set, the temperature range, and the supply voltage
the package and the type of delivery.
For the available ordering codes for the XC226x please refer to your responsible sales
representative or your local distributor.
This document describes several derivatives of the XC226x group. Table 1 enumerates
these derivatives and summarizes the differences. As this document refers to all of these
derivatives, some descriptions may not apply to a specific product.
For simplicity all versions are referred to by the term XC226x throughout this document.
Data Sheet
5
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 1
Summary of Features
XC226x Derivative Synopsis
Derivative1)
Temp.
Range
Program
Memory
PSRAM2)
CCU6 ADC3) Interfaces
Mod. Chan.
SAK-XC226796F66L
-40 °C to
125 °C
768 Kbytes 64 Kbytes
Flash
0, 1,
2, 3
8+8
5 CAN Nodes,
6 Serial Chan.
SAK-XC226772F66L
-40 °C to
125 °C
576 Kbytes 32 Kbytes
Flash
0, 1,
2, 3
8+8
5 CAN Nodes,
6 Serial Chan.
SAK-XC226756F66L
-40 °C to
125 °C
448 Kbytes 16 Kbytes
Flash
0, 1,
2, 3
8+8
5 CAN Nodes,
6 Serial Chan.
SAK-XC226496F66L
-40 °C to
125 °C
768 Kbytes 64 Kbytes
Flash
0, 1
8
2 CAN Nodes,
4 Serial Chan.
SAK-XC226472F66L
-40 °C to
125 °C
576 Kbytes 32 Kbytes
Flash
0, 1
8
2 CAN Nodes,
4 Serial Chan.
SAK-XC226456F66L
-40 °C to
125 °C
448 Kbytes 16 Kbytes
Flash
0, 1
8
2 CAN Nodes,
4 Serial Chan.
1) This Data Sheet is valid for devices starting with and including design step AA.
2) All derivatives additionally provide 1 Kbyte SBRAM, 2 Kbytes DPRAM, and 16 Kbytes DSRAM.
3) Analog input channels are listed for each Analog/Digital Converter module separately.
Data Sheet
6
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
2
General Device Information
General Device Information
The XC226x derivatives are high-performance members of the Infineon XC2000 Family
of full featured single-chip CMOS microcontrollers. These devices extend the
functionality and performance of the C166 Family in terms of instructions (MAC unit),
peripherals, and speed. They combine high CPU performance (up to 66 million
instructions per second) with high peripheral functionality and enhanced IO-capabilities.
Optimized peripherals can be adapted to the application’s requirements in a flexible way.
These derivatives also provide clock generation via PLL and internal or external clock
sources, and various on-chip memory modules such as program Flash, program RAM,
and data RAM.
VAREFVAGND TRef VDDI VDDP VSS
(1)
(1)
(4)
(9)
(4)
Port 0
8 bit
XTAL1
XTAL2
Port 1
8 bit
ESR0
ESR1
Port 2
13 bit
XC226x
Port 10
16 bit
Port 4
4 bit
Port 6
3 bit
Port 15
5 bit
Port 7
5 bit
Port 5
11 bit
PORST
TRST
TESTM
JTAG Debug
4 bit 2 bit
via Port Pins
M C_XC2X_LOGSYM B4
Figure 1
Data Sheet
Logic Symbol
7
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
2.1
General Device Information
Pin Configuration and Definition
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
VDDPB
ESR0
ESR1
PORST
XTAL1
XTAL2
P1.7
P1.6
P1.5
P10.15
P1.4
P10.14
VDDI1
P1.3
P10.13
P10.12
P1.2
P10.11
P10.10
P1.1
P10.9
P10.8
P1.0
VDDPB
VSS
The pins of the XC226x are described in detail in Table 2, including all their alternate
functions. For explanations, please refer to the footnotes at the table’s end. Figure 2
summarizes all pins in a condensed way, showing their location on the 4 sides of the
package.
VSS
VDDP
B
TESTM
P7.2
TRST
P7.0
P7.3
P7.1
P7.4
VDDIM
P6.0
P6.1
P6.2
VDDPA
P15.0
P15.2
P15.4
P15.5
P15.6
VAREF
VAGND
P5.0
P5.2
P5.3
XC226x
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
VDDPB
P0. 7
P10.7
P10.6
P0. 6
P10.5
P10.4
P0. 5
P10.3
P2. 10
TRef
VDDI1
P0. 4
P10. 2
P0. 3
P10.1
P10.0
P0. 2
P2. 9
P2. 8
P0. 1
P2. 7
P0. 0
VDDPB
VSS
V SS
V DDPB
P5.4
P5.5
P5.8
P5.9
P5.10
P5.11
P5.13
P5.15
P2.12
P2.11
VDDI1
P2.0
P2.1
P2.2
P4.0
P2.3
P4.1
P2.4
P2.5
P4.2
P2.6
P4.3
V DDPB
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VDDPB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
MC_XC2X_PIN100
Figure 2
Data Sheet
Pin Configuration (top view)
8
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
General Device Information
Notes to Pin Definitions
1. Ctrl.: The output signal for a port pin is selected via bitfield PC in the associated
register Px_IOCRy. Output O0 is selected by setting the respective bitfield PC to
1x00B, output O1 is selected by 1x01B, etc.
Output signal OH is controlled by hardware.
2. Type: Indicates the employed pad type (St=standard pad, Sp=special pad,
DP=double pad, In=input pad, PS=power supply) and its power supply domain (A, B,
M, 1).
Table 2
Pin Definitions and Functions
Pin
Symbol
Ctrl.
Type Function
3
TESTM
I
In/B
4
P7.2
O0 / I St/B
Bit 2 of Port 7, General Purpose Input/Output
EMUX0
O1
St/B
External Analog MUX Control Output 0
TxDC4
O2
St/B
CAN Node 4 Transmit Data Output
CCU62_
CCPOS0A
I
St/B
CCU62 Position Input 0
TDI_C
I
St/B
JTAG Test Data Input
5
TRST
I
In/B
Test-System Reset Input
For normal system operation, pin TRST should be
held low. A high level at this pin at the rising edge
of PORST activates the XC226x’s debug system.
In this case, pin TRST must be driven low once to
reset the debug system.
6
P7.0
O0 / I St/B
Bit 0 of Port 7, General Purpose Input/Output
T3OUT
O1
St/B
GPT1 Timer T3 Toggle Latch Output
T6OUT
O2
St/B
GPT2 Timer T6 Toggle Latch Output
TDO
OH
St/B
JTAG Test Data Output
RxDC4B
I
St/B
CAN Node 4 Receive Data Input
Data Sheet
Testmode Enable
Enables factory test modes, must be held HIGH for
normal operation (connect to VDDPB).
9
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
7
P7.3
O0 / I St/B
Bit 3 of Port 7, General Purpose Input/Output
EMUX1
O1
St/B
External Analog MUX Control Output 1
U0C1_DOUT O2
St/B
USIC0 Channel 1 Shift Data Output
U0C0_DOUT O3
St/B
USIC0 Channel 0 Shift Data Output
CCU62_
CCPOS1A
I
St/B
CCU62 Position Input 1
TMS_C
I
St/B
JTAG Test Mode Selection Input
U0C1_DX0F
I
St/B
USIC0 Channel 1 Shift Data Input
P7.1
O0 / I St/B
Bit 1 of Port 7, General Purpose Input/Output
EXTCLK
O1
St/B
Programmable Clock Signal Output
TxDC4
O2
St/B
CAN Node 4 Transmit Data Output
CCU62_
CTRAPA
I
St/B
CCU62 Emergency Trap Input
BRKIN_C
I
St/B
OCDS Break Signal Input
P7.4
O0 / I St/B
Bit 4 of Port 7, General Purpose Input/Output
EMUX2
O1
St/B
External Analog MUX Control Output 2
U0C1_DOUT O2
St/B
USIC0 Channel 1 Shift Data Output
U0C1_SCLK
O3
St/B
USIC0 Channel 1 Shift Clock Output
CCU62_
CCPOS2A
I
St/B
CCU62 Position Input 2
TCK_C
I
St/B
JTAG Clock Input
U0C0_DX0D
I
St/B
USIC0 Channel 0 Shift Data Input
U0C1_DX1E
I
St/B
USIC0 Channel 1 Shift Clock Input
P6.0
O0 / I St/A
Bit 0 of Port 6, General Purpose Input/Output
EMUX0
O1
St/A
External Analog MUX Control Output 0
U1C1_DOUT O2
St/A
USIC1 Channel 1 Shift Data Output
BRKOUT
O3
St/A
OCDS Break Signal Output
ADCx_
REQGTyC
I
St/A
External Request Gate Input for ADC0/1
U1C1_DX0E
I
St/A
USIC1 Channel 1 Shift Data Input
8
9
11
Data Sheet
Type Function
10
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
12
P6.1
O0 / I St/A
Bit 1 of Port 6, General Purpose Input/Output
EMUX1
O1
St/A
External Analog MUX Control Output 1
T3OUT
O2
St/A
GPT1 Timer T3 Toggle Latch Output
U1C1_DOUT O3
St/A
USIC1 Channel 1 Shift Data Output
ADCx_
REQTRyC
I
St/A
External Request Trigger Input for ADC0/1
P6.2
O0 / I St/A
Bit 2 of Port 6, General Purpose Input/Output
EMUX2
O1
St/A
External Analog MUX Control Output 2
T6OUT
O2
St/A
GPT2 Timer T6 Toggle Latch Output
U1C1_SCLK
O3
St/A
USIC1 Channel 1 Shift Clock Output
U1C1_DX1C
I
St/A
USIC1 Channel 1 Shift Clock Input
P15.0
I
In/A
Bit 0 of Port 15, General Purpose Input
ADC1_CH0
I
In/A
Analog Input Channel 0 for ADC1
P15.2
I
In/A
Bit 2 of Port 15, General Purpose Input
ADC1_CH2
I
In/A
Analog Input Channel 2 for ADC1
T5IN
I
In/A
GPT2 Timer T5 Count/Gate Input
P15.4
I
In/A
Bit 4 of Port 15, General Purpose Input
ADC1_CH4
I
In/A
Analog Input Channel 4 for ADC1
T6IN
I
In/A
GPT2 Timer T6 Count/Gate Input
P15.5
I
In/A
Bit 5 of Port 15, General Purpose Input
ADC1_CH5
I
In/A
Analog Input Channel 5 for ADC1
T6EUD
I
In/A
GPT2 Timer T6 External Up/Down Control Input
P15.6
I
In/A
Bit 6 of Port 15, General Purpose Input
ADC1_CH6
I
In/A
Analog Input Channel 6 for ADC1
-
PS/A Reference Voltage for A/D Converters ADC0/1
21
VAREF
VAGND
-
PS/A Reference Ground for A/D Converters ADC0/1
22
P5.0
I
In/A
Bit 0 of Port 5, General Purpose Input
ADC0_CH0
I
In/A
Analog Input Channel 0 for ADC0
P5.2
I
In/A
Bit 2 of Port 5, General Purpose Input
ADC0_CH2
I
In/A
Analog Input Channel 2 for ADC0
TDI_A
I
In/A
JTAG Test Data Input
13
15
16
17
18
19
20
23
Data Sheet
Type Function
11
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
Type Function
24
P5.3
I
In/A
Bit 3 of Port 5, General Purpose Input
ADC0_CH3
I
In/A
Analog Input Channel 3 for ADC0
T3IN
I
In/A
GPT1 Timer T3 Count/Gate Input
P5.4
I
In/A
Bit 4 of Port 5, General Purpose Input
ADC0_CH4
I
In/A
Analog Input Channel 4 for ADC0
CCU63_
T12HRB
I
In/A
External Run Control Input for T12 of CCU63
T3EUD
I
In/A
GPT1 Timer T3 External Up/Down Control Input
TMS_A
I
In/A
JTAG Test Mode Selection Input
P5.5
I
In/A
Bit 5 of Port 5, General Purpose Input
ADC0_CH5
I
In/A
Analog Input Channel 5 for ADC0
CCU60_
T12HRB
I
In/A
External Run Control Input for T12 of CCU60
P5.8
I
In/A
Bit 8 of Port 5, General Purpose Input
ADC0_CH8
I
In/A
Analog Input Channel 8 for ADC0
CCU6x_
T12HRC
I
In/A
External Run Control Input for T12 of
CCU60/1/2/3
CCU6x_
T13HRC
I
In/A
External Run Control Input for T13 of
CCU60/1/2/3
P5.9
I
In/A
Bit 9 of Port 5, General Purpose Input
ADC0_CH9
I
In/A
Analog Input Channel 9 for ADC0
CC2_T7IN
I
In/A
CAPCOM2 Timer T7 Count Input
P5.10
I
In/A
Bit 10 of Port 5, General Purpose Input
ADC0_CH10
I
In/A
Analog Input Channel 10 for ADC0
BRKIN_A
I
In/A
OCDS Break Signal Input
P5.11
I
In/A
Bit 11 of Port 5, General Purpose Input
ADC0_CH11
I
In/A
Analog Input Channel 11 for ADC0
P5.13
I
In/A
Bit 13 of Port 5, General Purpose Input
ADC0_CH13
I
In/A
Analog Input Channel 13 for ADC0
EX0BINB
I
In/A
External Interrupt Trigger Input
28
29
30
31
32
33
34
Data Sheet
12
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
Type Function
35
P5.15
I
In/A
Bit 15 of Port 5, General Purpose Input
ADC0_CH15
I
In/A
Analog Input Channel 15 for ADC0
P2.12
O0 / I St/B
Bit 12 of Port 2, General Purpose Input/Output
U0C0_
SELO4
O1
St/B
USIC0 Channel 0 Select/Control 4 Output
U0C1_
SELO3
O2
St/B
USIC0 Channel 1 Select/Control 3 Output
READY
I
St/B
External Bus Interface READY Input
P2.11
O0 / I St/B
Bit 11 of Port 2, General Purpose Input/Output
U0C0_
SELO2
O1
St/B
USIC0 Channel 0 Select/Control 2 Output
U0C1_
SELO2
O2
St/B
USIC0 Channel 1 Select/Control 2 Output
BHE/WRH
OH
St/B
External Bus Interf. High-Byte Control Output
Can operate either as Byte High Enable (BHE) or
as Write strobe for High Byte (WRH).
P2.0
O0 / I St/B
Bit 0 of Port 2, General Purpose Input/Output
CCU63_
CC60
O2 / I St/B
CCU63 Channel 0 Input/Output
AD13
OH / I St/B
External Bus Interface Address/Data Line 13
RxDC0C
I
CAN Node 0 Receive Data Input
P2.1
O0 / I St/B
Bit 1 of Port 2, General Purpose Input/Output
TxDC0
O1
CAN Node 0 Transmit Data Output
CCU63_
CC61
O2 / I St/B
CCU63 Channel 1 Input/Output
AD14
OH / I St/B
External Bus Interface Address/Data Line 14
EX0AINA
I
External Interrupt Trigger Input
P2.2
O0 / I St/B
Bit 2 of Port 2, General Purpose Input/Output
TxDC1
O1
CAN Node 1 Transmit Data Output
CCU63_
CC62
O2 / I St/B
CCU63 Channel 2 Input/Output
AD15
OH / I St/B
External Bus Interface Address/Data Line 15
EX1AINA
I
External Interrupt Trigger Input
36
37
39
40
41
Data Sheet
St/B
St/B
St/B
St/B
St/B
13
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
42
P4.0
O0 / I St/B
Bit 0 of Port 4, General Purpose Input/Output
CC2_8
O3 / I St/B
CAPCOM2 CC8IO Capture Inp./ Compare Out.
CS0
OH
External Bus Interface Chip Select 0 Output
P2.3
O0 / I St/B
43
Type Function
St/B
Bit 3 of Port 2, General Purpose Input/Output
U0C0_DOUT O1
St/B
USIC0 Channel 0 Shift Data Output
CCU63_
COUT63
O2
St/B
CCU63 Channel 3 Output
CC2_0
O3 / I St/B
CAPCOM2 CC0IO Capture Inp./ Compare Out.
A16
OH
St/B
External Bus Interface Address Line 16
U0C0_DX0E
I
St/B
USIC0 Channel 0 Shift Data Input
U0C1_DX0D
I
St/B
USIC0 Channel 1 Shift Data Input
Note: Not available in step AA.
44
45
RxDC0A
I
P4.1
O0 / I St/B
Bit 1 of Port 4, General Purpose Input/Output
TxDC2
O2
CAN Node 2 Transmit Data Output
CC2_9
O3 / I St/B
CAPCOM2 CC9IO Capture Inp./ Compare Out.
CS1
OH
External Bus Interface Chip Select 1 Output
P2.4
O0 / I St/B
U0C1_DOUT O1
St/B
St/B
St/B
St/B
CAN Node 0 Receive Data Input
Bit 4 of Port 2, General Purpose Input/Output
USIC0 Channel 1 Shift Data Output
Note: Not available in step AA.
TxDC0
O2
CC2_1
O3 / I St/B
CAPCOM2 CC1IO Capture Inp./ Compare Out.
A17
OH
St/B
External Bus Interface Address Line 17
U0C0_DX0F
I
St/B
USIC0 Channel 0 Shift Data Input
RxDC1A
I
St/B
CAN Node 1 Receive Data Input
Data Sheet
St/B
CAN Node 0 Transmit Data Output
14
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
46
P2.5
O0 / I St/B
Bit 5 of Port 2, General Purpose Input/Output
U0C0_
SCLKOUT
O1
St/B
USIC0 Channel 0 Shift Clock Output
TxDC0
O2
St/B
CAN Node 0 Transmit Data Output
CC2_2
O3 / I St/B
CAPCOM2 CC2IO Capture Inp./ Compare Out.
A18
OH
St/B
External Bus Interface Address Line 18
U0C0_DX1D
I
St/B
USIC0 Channel 0 Shift Clock Input
P4.2
O0 / I St/B
Bit 2 of Port 4, General Purpose Input/Output
TxDC2
O2
CAN Node 2 Transmit Data Output
CC2_10
O3 / I St/B
CAPCOM2 CC10IO Capture Inp./ Compare Out.
CS2
OH
St/B
External Bus Interface Chip Select 2 Output
T2IN
I
St/B
GPT1 Timer T2 Count/Gate Input
P2.6
O0 / I St/B
Bit 6 of Port 2, General Purpose Input/Output
U0C0_
SELO0
O1
St/B
USIC0 Channel 0 Select/Control 0 Output
U0C1_
SELO1
O2
St/B
USIC0 Channel 1 Select/Control 1 Output
CC2_3
O3 / I St/B
CAPCOM2 CC3IO Capture Inp./ Compare Out.
A19
OH
St/B
External Bus Interface Address Line 19
U0C0_DX2D
I
St/B
USIC0 Channel 0 Shift Control Input
RxDC0D
I
St/B
CAN Node 0 Receive Data Input
P4.3
O0 / I St/B
Bit 3 of Port 4, General Purpose Input/Output
CC2_11
O3 / I St/B
CAPCOM2 CC11IO Capture Inp./ Compare Out.
CS3
OH
St/B
External Bus Interface Chip Select 3 Output
RxDC2A
I
St/B
CAN Node 2 Receive Data Input
T2EUD
I
St/B
GPT1 Timer T2 External Up/Down Control Input
47
48
49
Data Sheet
Type Function
St/B
15
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
53
P0.0
O0 / I St/B
U1C0_DOUT O1
54
55
56
Type Function
St/B
Bit 0 of Port 0, General Purpose Input/Output
USIC1 Channel 0 Shift Data Output
CCU61_
CC60
O3 / I St/B
CCU61 Channel 0 Input/Output
A0
OH
St/B
External Bus Interface Address Line 0
U1C0_DX0A
I
St/B
USIC1 Channel 0 Shift Data Input
P2.7
O0 / I St/B
Bit 7 of Port 2, General Purpose Input/Output
U0C1_
SELO0
O1
St/B
USIC0 Channel 1 Select/Control 0 Output
U0C0_
SELO1
O2
St/B
USIC0 Channel 0 Select/Control 1 Output
CC2_4
O3 / I St/B
CAPCOM2 CC4IO Capture Inp./ Compare Out.
A20
OH
St/B
External Bus Interface Address Line 20
U0C1_DX2C
I
St/B
USIC0 Channel 1 Shift Control Input
RxDC1C
I
St/B
CAN Node 1 Receive Data Input
P0.1
O0 / I St/B
Bit 1 of Port 0, General Purpose Input/Output
U1C0_DOUT O1
St/B
USIC1 Channel 0 Shift Data Output
TxDC0
O2
St/B
CAN Node 0 Transmit Data Output
CCU61_
CC61
O3 / I St/B
CCU61 Channel 1 Input/Output
A1
OH
St/B
External Bus Interface Address Line 1
U1C0_DX0B
I
St/B
USIC1 Channel 0 Shift Data Input
U1C0_DX1A
I
St/B
USIC1 Channel 0 Shift Clock Input
P2.8
O0 / I DP/B Bit 8 of Port 2, General Purpose Input/Output
U0C1_
SCLKOUT
O1
DP/B USIC0 Channel 1 Shift Clock Output
EXTCLK
O2
DP/B Programmable Clock Signal Output
1)
CC2_5
O3 / I DP/B CAPCOM2 CC5IO Capture Inp./ Compare Out.
A21
OH
DP/B External Bus Interface Address Line 21
U0C1_DX1D
I
DP/B USIC0 Channel 1 Shift Clock Input
Data Sheet
16
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
57
P2.9
O0 / I St/B
58
59
Bit 9 of Port 2, General Purpose Input/Output
U0C1_DOUT O1
St/B
USIC0 Channel 1 Shift Data Output
TxDC1
O2
St/B
CAN Node 1 Transmit Data Output
CC2_6
O3 / I St/B
CAPCOM2 CC6IO Capture Inp./ Compare Out.
A22
OH
St/B
External Bus Interface Address Line 22
DIRIN
I
St/B
Clock Signal Input
TCK_A
I
St/B
JTAG Clock Input
P0.2
O0 / I St/B
Bit 2 of Port 0, General Purpose Input/Output
U1C0_
SCLKOUT
O1
St/B
USIC1 Channel 0 Shift Clock Output
TxDC0
O2
St/B
CAN Node 0 Transmit Data Output
CCU61_
CC62
O3 / I St/B
CCU61 Channel 2 Input/Output
A2
OH
St/B
External Bus Interface Address Line 2
U1C0_DX1B
I
St/B
USIC1 Channel 0 Shift Clock Input
P10.0
O0 / I St/B
U0C1_DOUT O1
60
Type Function
St/B
Bit 0 of Port 10, General Purpose Input/Output
USIC0 Channel 1 Shift Data Output
CCU60_
CC60
O2 / I St/B
CCU60 Channel 0 Input/Output
AD0
OH / I St/B
External Bus Interface Address/Data Line 0
U0C0_DX0A
I
St/B
USIC0 Channel 0 Shift Data Input
U0C1_DX0A
I
St/B
USIC0 Channel 1 Shift Data Input
P10.1
O0 / I St/B
U0C0_DOUT O1
St/B
Bit 1 of Port 10, General Purpose Input/Output
USIC0 Channel 0 Shift Data Output
CCU60_
CC61
O2 / I St/B
CCU60 Channel 1 Input/Output
AD1
OH / I St/B
External Bus Interface Address/Data Line 1
U0C0_DX0B
I
St/B
USIC0 Channel 0 Shift Data Input
U0C0_DX1A
I
St/B
USIC0 Channel 0 Shift Clock Input
Data Sheet
17
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
61
P0.3
O0 / I St/B
Bit 3 of Port 0, General Purpose Input/Output
U1C0_
SELO0
O1
St/B
USIC1 Channel 0 Select/Control 0 Output
U1C1_
SELO1
O2
St/B
USIC1 Channel 1 Select/Control 1 Output
CCU61_
COUT60
O3
St/B
CCU61 Channel 0 Output
A3
OH
St/B
External Bus Interface Address Line 3
U1C0_DX2A
I
St/B
USIC1 Channel 0 Shift Control Input
RxDC0B
I
St/B
CAN Node 0 Receive Data Input
P10.2
O0 / I St/B
Bit 2 of Port 10, General Purpose Input/Output
U0C0_
SCLKOUT
O1
USIC0 Channel 0 Shift Clock Output
CCU60_
CC62
O2 / I St/B
CCU60 Channel 2 Input/Output
AD2
OH / I St/B
External Bus Interface Address/Data Line 2
U0C0_DX1B
I
USIC0 Channel 0 Shift Clock Input
P0.4
O0 / I St/B
Bit 4 of Port 0, General Purpose Input/Output
U1C1_
SELO0
O1
St/B
USIC1 Channel 1 Select/Control 0 Output
U1C0_
SELO1
O2
St/B
USIC1 Channel 0 Select/Control 1 Output
CCU61_
COUT61
O3
St/B
CCU61 Channel 1 Output
A4
OH
St/B
External Bus Interface Address Line 4
U1C1_DX2A
I
St/B
USIC1 Channel 1 Shift Control Input
RxDC1B
I
St/B
CAN Node 1 Receive Data Input
TRef
IO
Sp/1
Control Pin for Core Voltage Generation
Connect TRef to VDDPB to use the on-chip EVRs.
Connect TRef to VDDI1 for external core voltage
supply (on-chip EVRs off).
62
63
65
Data Sheet
Type Function
St/B
St/B
18
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
66
P2.10
O0 / I St/B
67
68
69
Type Function
Bit 10 of Port 2, General Purpose Input/Output
U0C1_DOUT O1
St/B
USIC0 Channel 1 Shift Data Output
U0C0_
SELO3
O2
St/B
USIC0 Channel 0 Select/Control 3 Output
CC2_7
O3 / I St/B
CAPCOM2 CC7IO Capture Inp./ Compare Out.
A23
OH
St/B
External Bus Interface Address Line 23
U0C1_DX0E
I
St/B
USIC0 Channel 1 Shift Data Input
CAPIN
I
St/B
GPT2 Register CAPREL Capture Input
P10.3
O0 / I St/B
Bit 3 of Port 10, General Purpose Input/Output
CCU60_
COUT60
O2
CCU60 Channel 0 Output
AD3
OH / I St/B
External Bus Interface Address/Data Line 3
U0C0_DX2A
I
St/B
USIC0 Channel 0 Shift Control Input
U0C1_DX2A
I
St/B
USIC0 Channel 1 Shift Control Input
P0.5
O0 / I St/B
Bit 5 of Port 0, General Purpose Input/Output
U1C1_
SCLKOUT
O1
St/B
USIC1 Channel 1 Shift Clock Output
U1C0_
SELO2
O2
St/B
USIC1 Channel 0 Select/Control 2 Output
CCU61_
COUT62
O3
St/B
CCU61 Channel 2 Output
A5
OH
St/B
External Bus Interface Address Line 5
U1C1_DX1A
I
St/B
USIC1 Channel 1 Shift Clock Input
U1C0_DX1C
I
St/B
USIC1 Channel 0 Shift Clock Input
P10.4
O0 / I St/B
Bit 4 of Port 10, General Purpose Input/Output
U0C0_
SELO3
O1
St/B
USIC0 Channel 0 Select/Control 3 Output
CCU60_
COUT61
O2
St/B
CCU60 Channel 1 Output
AD4
OH / I St/B
External Bus Interface Address/Data Line 4
U0C0_DX2B
I
St/B
USIC0 Channel 0 Shift Control Input
U0C1_DX2B
I
St/B
USIC0 Channel 1 Shift Control Input
Data Sheet
St/B
19
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
70
P10.5
O0 / I St/B
Bit 5 of Port 10, General Purpose Input/Output
U0C1_
SCLKOUT
O1
St/B
USIC0 Channel 1 Shift Clock Output
CCU60_
COUT62
O2
St/B
CCU60 Channel 2 Output
AD5
OH / I St/B
External Bus Interface Address/Data Line 5
U0C1_DX1B
I
USIC0 Channel 1 Shift Clock Input
P0.6
O0 / I St/B
71
72
Type Function
St/B
Bit 6 of Port 0, General Purpose Input/Output
U1C1_DOUT O1
St/B
USIC1 Channel 1 Shift Data Output
TxDC1
O2
St/B
CAN Node 1 Transmit Data Output
CCU61_
COUT63
O3
St/B
CCU61 Channel 3 Output
A6
OH
St/B
External Bus Interface Address Line 6
U1C1_DX0A
I
St/B
USIC1 Channel 1 Shift Data Input
CCU61_
CTRAPA
I
St/B
CCU61 Emergency Trap Input
U1C1_DX1B
I
St/B
USIC1 Channel 1 Shift Clock Input
P10.6
O0 / I St/B
Bit 6 of Port 10, General Purpose Input/Output
U0C0_DOUT O1
St/B
USIC0 Channel 0 Shift Data Output
TxDC4
O2
St/B
CAN Node 4 Transmit Data Output
U1C0_
SELO0
O3
St/B
USIC1 Channel 0 Select/Control 0 Output
AD6
OH / I St/B
External Bus Interface Address/Data Line 6
U0C0_DX0C
I
St/B
USIC0 Channel 0 Shift Data Input
U1C0_DX2D
I
St/B
USIC1 Channel 0 Shift Control Input
CCU60_
CTRAPA
I
St/B
CCU60 Emergency Trap Input
Data Sheet
20
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
73
P10.7
O0 / I St/B
74
78
Type Function
Bit 7 of Port 10, General Purpose Input/Output
U0C1_DOUT O1
St/B
USIC0 Channel 1 Shift Data Output
CCU60_
COUT63
O2
St/B
CCU60 Channel 3 Output
AD7
OH / I St/B
External Bus Interface Address/Data Line 7
U0C1_DX0B
I
St/B
USIC0 Channel 1 Shift Data Input
CCU60_
CCPOS0A
I
St/B
CCU60 Position Input 0
RxDC4C
I
St/B
CAN Node 4 Receive Data Input
P0.7
O0 / I St/B
Bit 7 of Port 0, General Purpose Input/Output
U1C1_DOUT O1
St/B
USIC1 Channel 1 Shift Data Output
U1C0_
SELO3
O2
St/B
USIC1 Channel 0 Select/Control 3 Output
A7
OH
St/B
External Bus Interface Address Line 7
U1C1_DX0B
I
St/B
USIC1 Channel 1 Shift Data Input
CCU61_
CTRAPB
I
St/B
CCU61 Emergency Trap Input
P1.0
O0 / I St/B
Bit 0 of Port 1, General Purpose Input/Output
U1C0_
MCLKOUT
O1
St/B
USIC1 Channel 0 Master Clock Output
U1C0_
SELO4
O2
St/B
USIC1 Channel 0 Select/Control 4 Output
A8
OH
St/B
External Bus Interface Address Line 8
EX0BINA
I
St/B
External Interrupt Trigger Input
CCU62_
CTRAPB
I
St/B
CCU62 Emergency Trap Input
Data Sheet
21
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
79
P10.8
O0 / I St/B
Bit 8 of Port 10, General Purpose Input/Output
U0C0_
MCLKOUT
O1
St/B
USIC0 Channel 0 Master Clock Output
U0C1_
SELO0
O2
St/B
USIC0 Channel 1 Select/Control 0 Output
AD8
OH / I St/B
External Bus Interface Address/Data Line 8
CCU60_
CCPOS1A
I
St/B
CCU60 Position Input 1
U0C0_DX1C
I
St/B
USIC0 Channel 0 Shift Clock Input
BRKIN_B
I
St/B
OCDS Break Signal Input
P10.9
O0 / I St/B
Bit 9 of Port 10, General Purpose Input/Output
U0C0_
SELO4
O1
St/B
USIC0 Channel 0 Select/Control 4 Output
U0C1_
MCLKOUT
O2
St/B
USIC0 Channel 1 Master Clock Output
AD9
OH / I St/B
External Bus Interface Address/Data Line 9
CCU60_
CCPOS2A
I
St/B
CCU60 Position Input 2
TCK_B
I
St/B
JTAG Clock Input
P1.1
O0 / I St/B
Bit 1 of Port 1, General Purpose Input/Output
CCU62_
COUT62
O1
St/B
CCU62 Channel 2 Output
U1C0_
SELO5
O2
St/B
USIC1 Channel 0 Select/Control 5 Output
U2C1_DOUT O3
St/B
USIC2 Channel 1 Shift Data Output
A9
OH
St/B
External Bus Interface Address Line 9
EX1BINA
I
St/B
External Interrupt Trigger Input
U2C1_DX0C
I
St/B
USIC2 Channel 1 Shift Data Input
80
81
Data Sheet
Type Function
22
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
82
P10.10
O0 / I St/B
Bit 10 of Port 10, General Purpose Input/Output
U0C0_
SELO0
O1
St/B
USIC0 Channel 0 Select/Control 0 Output
CCU60_
COUT63
O2
St/B
CCU60 Channel 3 Output
AD10
OH / I St/B
External Bus Interface Address/Data Line 10
U0C0_DX2C
I
St/B
USIC0 Channel 0 Shift Control Input
TDI_B
I
St/B
JTAG Test Data Input
U0C1_DX1A
I
St/B
USIC0 Channel 1 Shift Clock Input
P10.11
O0 / I St/B
Bit 11 of Port 10, General Purpose Input/Output
U1C0_
SCLKOUT
O1
St/B
USIC1 Channel 0 Shift Clock Output
BRKOUT
O2
St/B
OCDS Break Signal Output
AD11
OH / I St/B
External Bus Interface Address/Data Line 11
U1C0_DX1D
I
St/B
USIC1 Channel 0 Shift Clock Input
RxDC2B
I
St/B
CAN Node 2 Receive Data Input
TMS_B
I
St/B
JTAG Test Mode Selection Input
P1.2
O0 / I St/B
Bit 2 of Port 1, General Purpose Input/Output
CCU62_
CC62
O1 / I St/B
CCU62 Channel 2 Input/Output
U1C0_
SELO6
O2
St/B
USIC1 Channel 0 Select/Control 6 Output
U2C1_
SCLKOUT
O3
St/B
USIC2 Channel 1 Shift Clock Output
A10
OH
St/B
External Bus Interface Address Line 10
CCU61_
T12HRB
I
St/B
External Run Control Input for T12 of CCU61
EX2AINA
I
St/B
External Interrupt Trigger Input
U2C1_DX0D
I
St/B
USIC2 Channel 1 Shift Data Input
U2C1_DX1C
I
St/B
USIC2 Channel 1 Shift Clock Input
83
84
Data Sheet
Type Function
23
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
85
P10.12
O0 / I St/B
86
87
Type Function
Bit 12 of Port 10, General Purpose Input/Output
U1C0_DOUT O1
St/B
USIC1 Channel 0 Shift Data Output
TxDC2
O2
St/B
CAN Node 2 Transmit Data Output
TDO
O3
St/B
JTAG Test Data Output
AD12
OH / I St/B
External Bus Interface Address/Data Line 12
U1C0_DX0C
I
St/B
USIC1 Channel 0 Shift Data Input
U1C0_DX1E
I
St/B
USIC1 Channel 0 Shift Clock Input
P10.13
O0 / I St/B
Bit 13 of Port 10, General Purpose Input/Output
U1C0_DOUT O1
St/B
USIC1 Channel 0 Shift Data Output
TxDC3
O2
St/B
CAN Node 3 Transmit Data Output
U1C0_
SELO3
O3
St/B
USIC1 Channel 0 Select/Control 3 Output
WR/WRL
OH
St/B
External Bus Interface Write Strobe Output
Active for each external write access, when WR,
active for ext. writes to the low byte, when WRL.
U1C0_DX0D
I
St/B
USIC1 Channel 0 Shift Data Input
P1.3
O0 / I St/B
Bit 3 of Port 1, General Purpose Input/Output
CCU62_
COUT63
O1
St/B
CCU62 Channel 3 Output
U1C0_
SELO7
O2
St/B
USIC1 Channel 0 Select/Control 7 Output
U2C0_
SELO4
O3
St/B
USIC2 Channel 0 Select/Control 4 Output
A11
OH
St/B
External Bus Interface Address Line 11
CCU62_
T12HRB
I
St/B
External Run Control Input for T12 of CCU62
EX3AINA
I
St/B
External Interrupt Trigger Input
Data Sheet
24
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
89
P10.14
O0 / I St/B
Bit 14 of Port 10, General Purpose Input/Output
U1C0_
SELO1
O1
St/B
USIC1 Channel 0 Select/Control 1 Output
U0C1_DOUT O2
St/B
USIC0 Channel 1 Shift Data Output
RD
OH
St/B
External Bus Interface Read Strobe Output
U0C1_DX0C
I
St/B
USIC0 Channel 1 Shift Data Input
RxDC3C
I
St/B
CAN Node 3 Receive Data Input
P1.4
O0 / I St/B
Bit 4 of Port 1, General Purpose Input/Output
CCU62_
COUT61
O1
St/B
CCU62 Channel 1 Output
U1C1_
SELO4
O2
St/B
USIC1 Channel 1 Select/Control 4 Output
U2C0_
SELO5
O3
St/B
USIC2 Channel 0 Select/Control 5 Output
A12
OH
St/B
External Bus Interface Address Line 12
U2C0_DX2B
I
St/B
USIC2 Channel 0 Shift Control Input
P10.15
O0 / I St/B
Bit 15 of Port 10, General Purpose Input/Output
U1C0_
SELO2
O1
St/B
USIC1 Channel 0 Select/Control 2 Output
U0C1_DOUT O2
St/B
USIC0 Channel 1 Shift Data Output
U1C0_DOUT O3
St/B
USIC1 Channel 0 Shift Data Output
ALE
OH
St/B
External Bus Interf. Addr. Latch Enable Output
U0C1_DX1C
I
St/B
USIC0 Channel 1 Shift Clock Input
P1.5
O0 / I St/B
Bit 5 of Port 1, General Purpose Input/Output
CCU62_
COUT60
O1
St/B
CCU62 Channel 0 Output
U1C1_
SELO3
O2
St/B
USIC1 Channel 1 Select/Control 3 Output
BRKOUT
O3
St/B
OCDS Break Signal Output
A13
OH
St/B
External Bus Interface Address Line 13
U2C0_DX0C
I
St/B
USIC2 Channel 0 Shift Data Input
90
91
92
Data Sheet
Type Function
25
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
93
P1.6
O0 / I St/B
Bit 6 of Port 1, General Purpose Input/Output
CCU62_
CC61
O1 / I St/B
CCU62 Channel 1 Input/Output
U1C1_
SELO2
O2
St/B
USIC1 Channel 1 Select/Control 2 Output
U2C0_DOUT O3
St/B
USIC2 Channel 0 Shift Data Output
A14
OH
St/B
External Bus Interface Address Line 14
U2C0_DX0D
I
St/B
USIC2 Channel 0 Shift Data Input
P1.7
O0 / I St/B
Bit 7 of Port 1, General Purpose Input/Output
CCU62_
CC60
O1 / I St/B
CCU62 Channel 0 Input/Output
U1C1_
MCLKOUT
O2
St/B
USIC1 Channel 1 Master Clock Output
U2C0_
SCLKOUT
O3
St/B
USIC2 Channel 0 Shift Clock Output
A15
OH
St/B
External Bus Interface Address Line 15
U2C0_DX1C
I
St/B
USIC2 Channel 0 Shift Clock Input
95
XTAL2
O
Sp/1
Crystal Oscillator Amplifier Output
96
XTAL1
I
Sp/1
Crystal Oscillator Amplifier Input
To clock the device from an external source, drive
XTAL1, while leaving XTAL2 unconnected.
Voltages on XTAL1 must comply to the core
supply voltage VDDI1.
97
PORST
I
In/B
Power On Reset Input
A low level at this pin resets the XC226x
completely. A spike filter suppresses input pulses
<10 ns. Input pulses >100 ns safely pass the filter.
The minimum duration for a safe recognition
should be 120 ns.
98
ESR1
O0 / I St/B
External Service Request 1
EX0AINB
I
External Interrupt Trigger Input
ESR0
O0 / I St/B
94
99
Type Function
St/B
External Service Request 0
Note: After power-up, ESR0 operates as opendrain bidirectional reset with a weak pull-up.
Data Sheet
26
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 2
General Device Information
Pin Definitions and Functions (cont’d)
Pin
Symbol
Ctrl.
Type Function
10
VDDIM
-
PS/M Digital Core Supply Voltage for Domain M
Decouple with a 680 nF ceramic capacitor.
38,
64,
88
VDDI1
-
PS/1 Digital Core Supply Voltage for Domain 1
Decouple each with a 220 nF ceramic capacitor.
All VDDI1 pins must be connected to each other.
14
VDDPA
-
PS/A Digital Pad Supply Voltage for Domain A
Connect decoupling capacitors to adjacent
VDDP/VSS pin pairs as close as possible to the pins.
Note: The A/D_Converters and ports P5, P6, and
P15 are fed from supply voltage VDDPA.
2,
25,
27,
50,
52,
75,
77,
100
VDDPB
1,
26,
51,
76
VSS
-
PS/B Digital Pad Supply Voltage for Domain B
Connect decoupling capacitors to adjacent
VDDP/VSS pin pairs as close as possible to the pins.
Note: The on-chip voltage regulators and all ports
except P5, P6, and P15 are fed from supply
voltage VDDPB.
-
PS/-- Digital Ground
All VSS pins must be connected to the ground-line
or ground-plane.
1) To generate the reference clock output for bus timing measurement, fSYS must be selected as source for
EXTCLK and P2.8 must be selected as output pin. Also the high-speed clock pad must be enabled. This
configuration is referred to as reference clock output signal CLKOUT.
Data Sheet
27
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3
Functional Description
Functional Description
The architecture of the XC226x combines advantages of RISC, CISC, and DSP
processors with an advanced peripheral subsystem in a very well-balanced way. In
addition, the on-chip memory blocks allow the design of compact systems-on-silicon with
maximum performance (computing, control, communication).
The on-chip memory blocks (program code-memory and SRAM, dual-port RAM, data
SRAM) and the set of generic peripherals are connected to the CPU via separate buses.
Another bus, the LXBus, connects additional on-chip resources as well as external
resources (see Figure 3). This bus structure enhances the overall system performance
by enabling the concurrent operation of several subsystems of the XC226x.
The following block diagram gives an overview of the different on-chip components and
of the advanced, high bandwidth internal bus structure of the XC226x.
DPRAM
2 Kbytes
DSRAM
16 Kbytes
OCDS
Debug Support
EBC
LXBus Control
External Bus
Control
DMU
CPU
PMU
Program Flash 1
192/256 Kbytes
IMB
Program Flash 0
256 Kbytes
C166SV2 - Core
XTAL
Program Flash 2
0/64/256 Kbytes
WDT
Oscillators/PLL, System Fct.
Clock, Reset, Power Control,
Stand-By RAM
Interrupt & PEC
RTC
LXBus
PSRAM
16/32/64 Kbytes
ADC1 ADC0
8-Bit/
8-Bit/
10-Bit 10-Bit
8 Ch. 16 Ch.
GPT
...
CC2
CCU63
CCU60
T7
T12
T12
T8
T13
T13
T2
T3
T4
Peripheral
Data Bus
Interrupt Bus
T6
BRGen
Port 5
5
11
M ulti
CAN
RS232, RS232, RS232,
LIN,
LIN,
LIN,
5 ch.
SPI,
SPI,
SPI,
IIC, IIS IIC, IIS IIC, IIS
T5
P15
USIC2 USIC1 USIC0
2 Ch., 2 Ch., 2 Ch.,
64 x
64 x
64 x
Buffer Buffer Buffer
P10
P7 P6
16
5
P4
3
P2
4
P1
13
8
P0
8
MC_XC226X_BLOCKDIAGRAM
Figure 3
Data Sheet
Block Diagram
28
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.1
Functional Description
Memory Subsystem and Organization
The memory space of the XC226x is configured in a von Neumann architecture, which
means that all internal and external resources, such as code memory, data memory,
registers and I/O ports, are organized within the same linear address space.
Table 3
XC226x Memory Map
Address Area
Start Loc.
End Loc.
Area Size1)
Notes
IMB register space
FF’FF00H
FF’FFFFH
256 Bytes
–
Reserved (Access trap) F0’0000H
FF’FEFFH
<1 Mbyte
Minus IMB reg.
Reserved for EPSRAM E9’0000H
EF’FFFFH
448 Kbytes
Mirrors EPSRAM
Emulated PSRAM
E8’0000H
E8’FFFFH
64 Kbytes
Flash timing
Reserved for PSRAM
E1’0000H
E7’FFFFH
448 Kbytes
Mirrors PSRAM
Program SRAM
E0’0000H
E0’FFFFH
64 Kbytes
Maximum speed
Reserved for pr. mem.
CC’0000H
DF’FFFFH
<1.25 Mbytes –
Program Flash 2
C8’0000H
CB’FFFFH
256 Kbytes
Program Flash 1
C4’0000H
C7’FFFFH
256 Kbytes
–
–
C0’0000H
C3’FFFFH
256 Kbytes
2)
40’0000H
BF’FFFFH
8 Mbytes
–
20’5800H
3F’FFFFH
< 2 Mbytes
Minus USIC/CAN
USIC registers
20’4000H
20’57FFH
6 Kbytes
Accessed via EBC
MultiCAN registers
20’0000H
20’3FFFH
16 Kbytes
Accessed via EBC
External memory area
01’0000H
1F’FFFFH
< 2 Mbytes
Minus segment 0
SFR area
00’FE00H
00’FFFFH
0.5 Kbyte
–
Dual-Port RAM
00’F600H
00’FDFFH
2 Kbytes
–
Reserved for DPRAM
00’F200H
00’F5FFH
1 Kbyte
–
ESFR area
00’F000H
00’F1FFH
0.5 Kbyte
–
XSFR area
00’E000H
00’EFFFH
4 Kbytes
–
Data SRAM
00’A000H
00’DFFFH
16 Kbytes
–
Reserved for DSRAM
00’8000H
00’9FFFH
8 Kbytes
–
External memory area
00’0000H
00’7FFFH
32 Kbytes
–
Program Flash 0
External memory area
Available Ext. IO area
3)
1) The areas marked with “<” are slightly smaller than indicated, see column “Notes”.
2) One 4-Kbyte sector reserved for internal use.
3) Several pipeline optimizations are not active within the external IO area. This is necessary to control external
peripherals properly.
Data Sheet
29
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
This common memory space includes 16 Mbytes and is arranged as 256 segments of
64 Kbytes each, where each segment consists of four data pages of 16 Kbytes each.
The entire memory space can be accessed byte wise or word wise. Portions of the
on-chip DPRAM and the register spaces (ESFR/SFR) have additionally been made
directly bit addressable.
The internal data memory areas and the Special Function Register areas (SFR and
ESFR) are mapped into segment 0, the system segment.
The Program Management Unit (PMU) handles all code fetches and, therefore, controls
accesses to the program memories, such as Flash memory and PSRAM.
The Data Management Unit (DMU) handles all data transfers and, therefore, controls
accesses to the DSRAM and the on-chip peripherals.
Both units (PMU and DMU) are connected via the high-speed system bus to exchange
data. This is required if operands are read from program memory, code or data is written
to the PSRAM, code is fetched from external memory, or data is read from or written to
external resources, including peripherals on the LXBus (such as USIC or MultiCAN). The
system bus allows concurrent two-way communication for maximum transfer
performance.
Up to 64 Kbytes of on-chip Program SRAM (PSRAM) are provided to store user code
or data. The PSRAM is accessed via the PMU and is therefore optimized for code
fetches. A section of the PSRAM with programmable size can be write-protected.
Note: The actual size of the PSRAM depends on the chosen derivative (see Table 1).
16 Kbytes of on-chip Data SRAM (DSRAM) are provided as a storage for general user
data. The DSRAM is accessed via a separate interface and is, therefore, optimized for
data accesses.
2 Kbytes of on-chip Dual-Port RAM (DPRAM) are provided as a storage for user
defined variables, for the system stack, general purpose register banks. A register bank
can consist of up to 16 word wide (R0 to R15) and/or byte wide (RL0, RH0, …, RL7, RH7)
so-called General Purpose Registers (GPRs).
The upper 256 bytes of the DPRAM are directly bit addressable. When used by a GPR,
any location in the DPRAM is bit addressable.
1 Kbyte of on-chip Stand-By SRAM (SBRAM) is provided as a storage for systemrelevant user data that must be preserved while the major part of the device is powered
down. The SBRAM is accessed via a specific interface and is powered via domain M.
Data Sheet
30
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
1024 bytes (2 × 512 bytes) of the address space are reserved for the Special Function
Register areas (SFR space and ESFR space). SFRs are word wide registers which are
used for controlling and monitoring functions of the different on-chip units. Unused SFR
addresses are reserved for future members of the XC2000 Family. Therefore, they
should either not be accessed, or written with zeros, to ensure upward compatibility.
In order to meet the needs of designs where more memory is required than is provided
on chip, up to 12 Mbytes (approximately, see Table 3) of external RAM and/or ROM can
be connected to the microcontroller. The External Bus Interface also provides access to
external peripherals.
Up to 768 Kbytes of on-chip Flash memory store code, constant data, and control
data. The on-chip Flash memory consists of up to 3 modules with a maximum capacity
of 256 Kbytes each. Each module is organized in 4-Kbyte sectors. One 4-Kbyte sector
of Flash module 0 is used internally to store operation control parameters and protection
information.
Note: The actual size of the Flash memory depends on the chosen derivative (see
Table 1).
Each sector can be separately write protected1), erased and programmed (in blocks of
128 Bytes). The complete Flash area can be read-protected. A user-defined password
sequence temporarily unlocks protected areas. The Flash modules combine 128-bit
read accesses with protected and efficient writing algorithms for programming and
erasing. Dynamic error correction provides extremely high read data security for all read
accesses. Accesses to different Flash modules can be executed in parallel.
For timing characteristics, please refer to Section 4.4.2, for further Flash parameters,
please refer to Section 5.3.
1) To save control bits, sectors are clustered for protection purposes, they remain separate for
programming/erasing.
Data Sheet
31
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.2
Functional Description
External Bus Controller
All of the external memory accesses are performed by a particular on-chip External Bus
Controller (EBC). The EBC also controls accesses to resources connected to the on-chip
LXBus (MultiCAN and the USIC modules). The LXBus is an internal representation of
the external bus and allows accessing integrated peripherals and modules in the same
way as external components.
The EBC can be programmed either to Single Chip Mode when no external memory is
required, or to an external bus mode with the following possible selections1):
•
•
•
Address Bus Width with a range of 0 … 24-bit
Data Bus Width 8-bit or 16-bit
Bus Operation Multiplexed or Demultiplexed
The bus interface uses Port 10 and Port 2 for addresses and data. In the demultiplexed
bus modes, the lower addresses are separately output on Port 0 and Port 1. The number
of active segment address lines is selectable, restricting the external address space to
8 Mbytes … 64 Kbytes. This is required when interface lines shall be assigned to Port 2.
Up to 4 external CS signals (3 windows plus default) can be generated and output on
Port 4 in order to save external glue logic. External modules can directly be connected
to the common address/data bus and their individual select lines.
Important timing characteristics of the external bus interface have been made
programmable (via registers TCONCSx/FCONCSx) to allow the user the adaption of a
wide range of different types of memories and external peripherals.
Access to very slow memories or modules with varying access times is supported via a
particular ‘Ready’ function. The active level of the control input signal is selectable.
In addition, up to 4 independent address windows may be defined (via registers
ADDRSELx) which control accesses to resources with different bus characteristics.
These address windows are arranged hierarchically where window 4 overrides
window 3, and window 2 overrides window 1. All accesses to locations not covered by
these 4 address windows are controlled by TCONCS0/FCONCS0. The currently active
window can generate a chip select signal.
The external bus timing is related to the rising edge of the reference clock output
CLKOUT. The external bus protocol is compatible with that of the standard C166 Family.
1) Bus modes are switched dynamically if several address windows with different mode settings are used.
Data Sheet
32
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.3
Functional Description
Central Processing Unit (CPU)
The main core of the CPU consists of a 5-stage execution pipeline with a 2-stage
instruction-fetch pipeline, a 16-bit arithmetic and logic unit (ALU), a 32-bit/40-bit multiply
and accumulate unit (MAC), a register-file providing three register banks, and dedicated
SFRs. The ALU features a multiply and divide unit, a bit-mask generator, and a barrel
shifter.
PSRAM
Flash/ROM
PMU
CPU
Prefetch
Unit
Branch
Unit
FIFO
CSP
IP
VECSEG
CPUCON1
CPUCON2
Return
Stack
IDX0
IDX1
QX0
QX1
QR0
QR1
+/-
+/-
Multiply
Unit
MRW
+/-
MCW
MSW
MAH
MAL
2-Stage
Prefetch
Pipeline
TFR
Injection/
Exception
Handler
5-Stage
Pipeline
IFU
DPP0
DPP1
DPP2
DPP3
DPRAM
IPIP
SPSEG
SP
STKOV
STKUN
ADU
Division Unit
Bit-Mask-Gen.
Multiply Unit
Barrel-Shifter
MDC
CP
R15
R15
R14
R15
R14
R14
R15
R14
GPRs
GPRs
GPRs
GPRs
R1
R1
R0
R0R1
R0
R1
R0
RF
PSW
+/-
MDH
MDL
ZEROS
ONES
MAC
Buffer
ALU
WB
DSRAM
EBC
Peripherals
DMU
mca04917_x.vsd
Figure 4
Data Sheet
CPU Block Diagram
33
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
Based on these hardware provisions, most of the XC226x’s instructions can be executed
in just one machine cycle which requires 15 ns at 66 MHz CPU clock. For example, shift
and rotate instructions are always processed during one machine cycle independent of
the number of bits to be shifted. Also multiplication and most MAC instructions execute
in one single cycle. All multiple-cycle instructions have been optimized so that they can
be executed very fast as well: for example, a 32-/16-bit division is started within 4 cycles,
while the remaining cycles are executed in the background. Another pipeline
optimization, the branch target prediction, allows eliminating the execution time of
branch instructions if the prediction was correct.
The CPU has a register context consisting of up to three register banks with 16 word
wide GPRs each at its disposal. One of these register banks is physically allocated within
the on-chip DPRAM area. A Context Pointer (CP) register determines the base address
of the active register bank to be accessed by the CPU at any time. The number of these
register bank copies is only restricted by the available internal RAM space. For easy
parameter passing, a register bank may overlap others.
A system stack of up to 32 Kwords is provided as a storage for temporary data. The
system stack can be allocated to any location within the address space (preferably in the
on-chip RAM area), and it is accessed by the CPU via the stack pointer (SP) register.
Two separate SFRs, STKOV and STKUN, are implicitly compared against the stack
pointer value upon each stack access for the detection of a stack overflow or underflow.
The high performance offered by the hardware implementation of the CPU can efficiently
be utilized by a programmer via the highly efficient XC226x instruction set which includes
the following instruction classes:
•
•
•
•
•
•
•
•
•
•
•
•
•
Standard Arithmetic Instructions
DSP-Oriented Arithmetic Instructions
Logical Instructions
Boolean Bit Manipulation Instructions
Compare and Loop Control Instructions
Shift and Rotate Instructions
Prioritize Instruction
Data Movement Instructions
System Stack Instructions
Jump and Call Instructions
Return Instructions
System Control Instructions
Miscellaneous Instructions
The basic instruction length is either 2 or 4 bytes. Possible operand types are bits, bytes
and words. A variety of direct, indirect or immediate addressing modes are provided to
specify the required operands.
Data Sheet
34
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.4
Functional Description
Interrupt System
With an interrupt response time of typically 8 CPU clocks (in case of internal program
execution), the XC226x is capable of reacting very fast to the occurrence of nondeterministic events.
The architecture of the XC226x supports several mechanisms for fast and flexible
response to service requests that can be generated from various sources internal or
external to the microcontroller. Any of these interrupt requests can be programmed to
being serviced by the Interrupt Controller or by the Peripheral Event Controller (PEC).
In contrast to a standard interrupt service where the current program execution is
suspended and a branch to the interrupt vector table is performed, just one cycle is
‘stolen’ from the current CPU activity to perform a PEC service. A PEC service implies a
single byte or word data transfer between any two memory locations with an additional
increment of either the PEC source, or the destination pointer, or both. An individual PEC
transfer counter is implicitly decremented for each PEC service except when performing
in the continuous transfer mode. When this counter reaches zero, a standard interrupt is
performed to the corresponding source related vector location. PEC services are very
well suited, for example, for supporting the transmission or reception of blocks of data.
The XC226x has 8 PEC channels each of which offers such fast interrupt-driven data
transfer capabilities.
A separate control register which contains an interrupt request flag, an interrupt enable
flag and an interrupt priority bit field exists for each of the possible interrupt nodes. Via
its related register, each node can be programmed to one of sixteen interrupt priority
levels. Once having been accepted by the CPU, an interrupt service can only be
interrupted by a higher prioritized service request. For the standard interrupt processing,
each of the possible interrupt nodes has a dedicated vector location.
Fast external interrupt inputs are provided to service external interrupts with high
precision requirements. These fast interrupt inputs feature programmable edge
detection (rising edge, falling edge, or both edges).
Software interrupts are supported by means of the ‘TRAP’ instruction in combination with
an individual trap (interrupt) number.
Table 4 shows all of the possible XC226x interrupt sources and the corresponding
hardware-related interrupt flags, vectors, vector locations and trap (interrupt) numbers.
Note: Interrupt nodes which are not assigned to peripherals (unassigned nodes), may
be used to generate software controlled interrupt requests by setting the
respective interrupt request bit (xIR).
Data Sheet
35
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 4
Functional Description
XC226x Interrupt Nodes
Source of Interrupt or PEC
Service Request
Control
Register
Vector
Location1)
Trap
Number
CAPCOM Register 16, or
ERU Request 0
CC2_CC16IC
xx’0040H
10H / 16D
CAPCOM Register 17, or
ERU Request 1
CC2_CC17IC
xx’0044H
11H / 17D
CAPCOM Register 18, or
ERU Request 2
CC2_CC18IC
xx’0048H
12H / 18D
CAPCOM Register 19, or
ERU Request 3
CC2_CC19IC
xx’004CH
13H / 19D
CAPCOM Register 20, or
USIC0 Request 6
CC2_CC20IC
xx’0050H
14H / 20D
CAPCOM Register 21, or
USIC0 Request 7
CC2_CC21IC
xx’0054H
15H / 21D
CAPCOM Register 22, or
USIC1 Request 6
CC2_CC22IC
xx’0058H
16H / 22D
CAPCOM Register 23, or
USIC1 Request 7
CC2_CC23IC
xx’005CH
17H / 23D
CAPCOM Register 24, or
ERU Request 0
CC2_CC24IC
xx’0060H
18H / 24D
CAPCOM Register 25, or
ERU Request 1
CC2_CC25IC
xx’0064H
19H / 25D
CAPCOM Register 26, or
ERU Request 2
CC2_CC26IC
xx’0068H
1AH / 26D
CAPCOM Register 27, or
ERU Request 3
CC2_CC27IC
xx’006CH
1BH / 27D
CAPCOM Register 28, or
USIC2 Request 6
CC2_CC28IC
xx’0070H
1CH / 28D
CAPCOM Register 29, or
USIC2 Request 7
CC2_CC29IC
xx’0074H
1DH / 29D
CAPCOM Register 30
CC2_CC30IC
xx’0078H
1EH / 30D
CAPCOM Register 31
CC2_CC31IC
xx’007CH
1FH / 31D
GPT1 Timer 2
GPT12E_T2IC
xx’0080H
20H / 32D
GPT1 Timer 3
GPT12E_T3IC
xx’0084H
21H / 33D
GPT1 Timer 4
GPT12E_T4IC
xx’0088H
22H / 34D
Data Sheet
36
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 4
Functional Description
XC226x Interrupt Nodes (cont’d)
Source of Interrupt or PEC
Service Request
Control
Register
Vector
Location1)
Trap
Number
GPT2 Timer 5
GPT12E_T5IC
xx’008CH
23H / 35D
GPT2 Timer 6
GPT12E_T6IC
xx’0090H
24H / 36D
GPT2 CAPREL Register
GPT12E_CRIC
xx’0094H
25H / 37D
CAPCOM Timer 7
CC2_T7IC
xx’0098H
26H / 38D
CAPCOM Timer 8
CC2_T8IC
xx’009CH
27H / 39D
A/D Converter Request 0
ADC_0IC
xx’00A0H
28H / 40D
A/D Converter Request 1
ADC_1IC
xx’00A4H
29H / 41D
A/D Converter Request 2
ADC_2IC
xx’00A8H
2AH / 42D
A/D Converter Request 3
ADC_3IC
xx’00ACH
2BH / 43D
A/D Converter Request 4
ADC_4IC
xx’00B0H
2CH / 44D
A/D Converter Request 5
ADC_5IC
xx’00B4H
2DH / 45D
A/D Converter Request 6
ADC_6IC
xx’00B8H
2EH / 46D
A/D Converter Request 7
ADC_7IC
xx’00BCH
2FH / 47D
CCU60 Request 0
CCU60_0IC
xx’00C0H
30H / 48D
CCU60 Request 1
CCU60_1IC
xx’00C4H
31H / 49D
CCU60 Request 2
CCU60_2IC
xx’00C8H
32H / 50D
CCU60 Request 3
CCU60_3IC
xx’00CCH
33H / 51D
CCU61 Request 0
CCU61_0IC
xx’00D0H
34H / 52D
CCU61 Request 1
CCU61_1IC
xx’00D4H
35H / 53D
CCU61 Request 2
CCU61_2IC
xx’00D8H
36H / 54D
CCU61 Request 3
CCU61_3IC
xx’00DCH
37H / 55D
CCU62 Request 0
CCU62_0IC
xx’00E0H
38H / 56D
CCU62 Request 1
CCU62_1IC
xx’00E4H
39H / 57D
CCU62 Request 2
CCU62_2IC
xx’00E8H
3AH / 58D
CCU62 Request 3
CCU62_3IC
xx’00ECH
3BH / 59D
CCU63 Request 0
CCU63_0IC
xx’00F0H
3CH / 60D
CCU63 Request 1
CCU63_1IC
xx’00F4H
3DH / 61D
CCU63 Request 2
CCU63_2IC
xx’00F8H
3EH / 62D
CCU63 Request 3
CCU63_3IC
xx’00FCH
3FH / 63D
CAN Request 0
CAN_0IC
xx’0100H
40H / 64D
Data Sheet
37
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 4
Functional Description
XC226x Interrupt Nodes (cont’d)
Source of Interrupt or PEC
Service Request
Control
Register
Vector
Location1)
Trap
Number
CAN Request 1
CAN_1IC
xx’0104H
41H / 65D
CAN Request 2
CAN_2IC
xx’0108H
42H / 66D
CAN Request 3
CAN_3IC
xx’010CH
43H / 67D
CAN Request 4
CAN_4IC
xx’0110H
44H / 68D
CAN Request 5
CAN_5IC
xx’0114H
45H / 69D
CAN Request 6
CAN_6IC
xx’0118H
46H / 70D
CAN Request 7
CAN_7IC
xx’011CH
47H / 71D
CAN Request 8
CAN_8IC
xx’0120H
48H / 72D
CAN Request 9
CAN_9IC
xx’0124H
49H / 73D
CAN Request 10
CAN_10IC
xx’0128H
4AH / 74D
CAN Request 11
CAN_11IC
xx’012CH
4BH / 75D
CAN Request 12
CAN_12IC
xx’0130H
4CH / 76D
CAN Request 13
CAN_13IC
xx’0134H
4DH / 77D
CAN Request 14
CAN_14IC
xx’0138H
4EH / 78D
CAN Request 15
CAN_15IC
xx’013CH
4FH / 79D
USIC0 Request 0
U0C0_0IC
xx’0140H
50H / 80D
USIC0 Request 1
U0C0_1IC
xx’0144H
51H / 81D
USIC0 Request 2
U0C0_2IC
xx’0148H
52H / 82D
USIC0 Request 3
U0C1_0IC
xx’014CH
53H / 83D
USIC0 Request 4
U0C1_1IC
xx’0150H
54H / 84D
USIC0 Request 5
U0C1_2IC
xx’0154H
55H / 85D
USIC1 Request 0
U1C0_0IC
xx’0158H
56H / 86D
USIC1 Request 1
U1C0_1IC
xx’015CH
57H / 87D
USIC1 Request 2
U1C0_2IC
xx’0160H
58H / 88D
USIC1 Request 3
U1C1_0IC
xx’0164H
59H / 89D
USIC1 Request 4
U1C1_1IC
xx’0168H
5AH / 90D
USIC1 Request 5
U1C1_2IC
xx’016CH
5BH / 91D
USIC2 Request 0
U2C0_0IC
xx’0170H
5CH / 92D
USIC2 Request 1
U2C0_1IC
xx’0174H
5DH / 93D
USIC2 Request 2
U2C0_2IC
xx’0178H
5EH / 94D
Data Sheet
38
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 4
Functional Description
XC226x Interrupt Nodes (cont’d)
Source of Interrupt or PEC
Service Request
Control
Register
Vector
Location1)
Trap
Number
USIC2 Request 3
U2C1_0IC
xx’017CH
5FH / 95D
USIC2 Request 4
U2C1_1IC
xx’0180H
60H / 96D
USIC2 Request 5
U2C1_2IC
xx’0184H
61H / 97D
Unassigned node
–
xx’0188H
62H / 98D
Unassigned node
–
xx’018CH
63H / 99D
Unassigned node
–
xx’0190H
64H / 100D
Unassigned node
–
xx’0194H
65H / 101D
Unassigned node
–
xx’0198H
66H / 102D
Unassigned node
–
xx’019CH
67H / 103D
Unassigned node
–
xx’01A0H
68H / 104D
Unassigned node
–
xx’01A4H
69H / 105D
Unassigned node
–
xx’01A8H
6AH / 106D
SCU Request 1
SCU_1IC
xx’01ACH
6BH / 107D
SCU Request 0
SCU_0IC
xx’01B0H
6CH / 108D
Program Flash Modules
PFM_IC
xx’01B4H
6DH / 109D
RTC
RTC_IC
xx’01B8H
6EH / 110D
End of PEC Subchannel
EOPIC
xx’01BCH
6FH / 111D
1) Register VECSEG defines the segment where the vector table is located to.
Bitfield VECSC in register CPUCON1 defines the distance between two adjacent vectors. This table
represents the default setting, with a distance of 4 (two words) between two vectors.
Data Sheet
39
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
The XC226x also provides an excellent mechanism to identify and to process exceptions
or error conditions that arise during run-time, so-called ‘Hardware Traps’. Hardware
traps cause immediate non-maskable system reaction which is similar to a standard
interrupt service (branching to a dedicated vector table location). The occurrence of a
hardware trap is additionally signified by an individual bit in the trap flag register (TFR).
Except when another higher prioritized trap service is in progress, a hardware trap will
interrupt any actual program execution. In turn, hardware trap services can normally not
be interrupted by standard or PEC interrupts.
Table 5 shows all of the possible exceptions or error conditions that can arise during runtime:
Table 5
Hardware Trap Summary
Exception Condition
Trap
Flag
Trap
Vector
Vector
Trap
Trap
Location1) Number Priority
Reset Functions
–
RESET
xx’0000H
00H
III
Class A Hardware Traps:
• System Request 0
• Stack Overflow
• Stack Underflow
• Software Break
SR0
STKOF
STKUF
SOFTBRK
SR0TRAP
STOTRAP
STUTRAP
SBRKTRAP
xx’0008H
xx’0010H
xx’0018H
xx’0020H
02H
04H
06H
08H
II
II
II
II
SR1
UNDOPC
ACER
PRTFLT
BTRAP
BTRAP
BTRAP
BTRAP
xx’0028H
xx’0028H
xx’0028H
xx’0028H
0AH
0AH
0AH
0AH
I
I
I
I
ILLOPA
BTRAP
xx’0028H
0AH
I
Reserved
–
–
[2CH - 3CH] [0BH 0FH]
–
Software Traps:
• TRAP Instruction
–
–
Any
Any
[xx’0000H - [00H xx’01FCH] 7FH]
in steps of
4H
Current
CPU
Priority
Class B Hardware Traps:
• System Request 1
• Undefined Opcode
• Memory Access Error
• Protected Instruction
Fault
• Illegal Word Operand
Access
1) Register VECSEG defines the segment where the vector table is located to.
Bitfield VECSC in register CPUCON1 defines the distance between two adjacent vectors. This table
represents the default setting, with a distance of 4 (two words) between two vectors.
Data Sheet
40
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.5
Functional Description
On-Chip Debug Support (OCDS)
The On-Chip Debug Support system provides a broad range of debug and emulation
features built into the XC226x. The user software running on the XC226x can thus be
debugged within the target system environment.
The OCDS is controlled by an external debugging device via the debug interface,
consisting of the IEEE-1149-conforming JTAG port and a break interface. The debugger
controls the OCDS via a set of dedicated registers accessible via the JTAG interface.
Additionally, the OCDS system can be controlled by the CPU, e.g. by a monitor program.
An injection interface allows the execution of OCDS-generated instructions by the CPU.
Multiple breakpoints can be triggered by on-chip hardware, by software, or by an
external trigger input. Single stepping is supported as well as the injection of arbitrary
instructions and read/write access to the complete internal address space. A breakpoint
trigger can be answered with a CPU-halt, a monitor call, a data transfer, or/and the
activation of an external signal.
Tracing data can be obtained via the JTAG interface or via the external bus interface for
increased performance.
The debug interface uses a set of 6 interface signals (4 JTAG lines, 2 optional break
lines) to communicate with external circuitry.
Data Sheet
41
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.6
Functional Description
Capture/Compare Unit (CAPCOM2)
The CAPCOM2 unit supports generation and control of timing sequences on up to
16 channels with a maximum resolution of 1 system clock cycle (8 cycles in staggered
mode). The CAPCOM2 unit is typically used to handle high speed I/O tasks such as
pulse and waveform generation, pulse width modulation (PWM), Digital to Analog (D/A)
conversion, software timing, or time recording relative to external events.
Two 16-bit timers (T7/T8) with reload registers provide two independent time bases for
the capture/compare register array.
The input clock for the timers is programmable to several prescaled values of the internal
system clock, or may be derived from an overflow/underflow of timer T6 in module GPT2.
This provides a wide range of variation for the timer period and resolution and allows
precise adjustments to the application specific requirements. In addition, an external
count input for CAPCOM2 timer T7 allows event scheduling for the capture/compare
registers relative to external events.
The capture/compare register array contains 16 dual purpose capture/compare
registers, each of which may be individually allocated to either CAPCOM2 timer T7 or T8
and programmed for capture or compare function.
All registers of the CAPCOM2 module have each one port pin associated with it which
serves as an input pin for triggering the capture function, or as an output pin to indicate
the occurrence of a compare event.
Table 6
Compare Modes (CAPCOM2)
Compare Modes
Function
Mode 0
Interrupt-only compare mode;
Several compare interrupts per timer period are possible
Mode 1
Pin toggles on each compare match;
Several compare events per timer period are possible
Mode 2
Interrupt-only compare mode;
Only one compare interrupt per timer period is generated
Mode 3
Pin set ‘1’ on match; pin reset ‘0’ on compare timer overflow;
Only one compare event per timer period is generated
Double Register
Mode
Two registers operate on one pin;
Pin toggles on each compare match;
Several compare events per timer period are possible
Single Event Mode
Generates single edges or pulses;
Can be used with any compare mode
When a capture/compare register has been selected for capture mode, the current
contents of the allocated timer will be latched (‘captured’) into the capture/compare
Data Sheet
42
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
register in response to an external event at the port pin which is associated with this
register. In addition, a specific interrupt request for this capture/compare register is
generated. Either a positive, a negative, or both a positive and a negative external signal
transition at the pin can be selected as the triggering event.
The contents of all registers which have been selected for one of the five compare modes
are continuously compared with the contents of the allocated timers.
When a match occurs between the timer value and the value in a capture/compare
register, specific actions will be taken based on the selected compare mode.
Data Sheet
43
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
Reload Reg.
T7REL
fC C
T7IN
T6OUF
T7
Input
Control
Timer T7
CCxIO
CCxIO
CCxIRQ
CCxIRQ
Mode
Control
(Capture
or
Compare)
Sixteen
16-bit
Capture/
Compare
Registers
CCxIO
fC C
T6OUF
T7IRQ
CCxIRQ
T8
Input
Control
Timer T8
T8IRQ
Reload Reg.
T8REL
CAPCOM2 provides channels x = 16 … 31.
(see signals CCxIO and CCxIRQ)
MCB05569_2
Figure 5
Data Sheet
CAPCOM2 Unit Block Diagram
44
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.7
Functional Description
Capture/Compare Units CCU6x
The XC226x features up to four CCU6 units (CCU60, CCU61, CCU62, CCU63).
The CCU6 is a high-resolution capture and compare unit with application specific modes.
It provides inputs to start the timers synchronously, an important feature in devices with
several CCU6 modules.
The module provides two independent timers (T12, T13), that can be used for PWM
generation, especially for AC-motor control. Additionally, special control modes for block
commutation and multi-phase machines are supported.
Timer 12 Features
•
•
•
•
•
•
•
•
•
•
Three capture/compare channels, each channel can be used either as capture or as
compare channel.
Generation of a three-phase PWM supported (six outputs, individual signals for highside and low-side switches)
16 bit resolution, maximum count frequency = peripheral clock
Dead-time control for each channel to avoid short-circuits in the power stage
Concurrent update of the required T12/13 registers
Center-aligned and edge-aligned PWM can be generated
Single-shot mode supported
Many interrupt request sources
Hysteresis-like control mode
Automatic start on an HW event (T12HR, for synchronization purposes)
Timer 13 Features
•
•
•
•
•
•
One independent compare channel with one output
16 bit resolution, maximum count frequency = peripheral clock
Can be synchronized to T12
Interrupt generation at period-match and compare-match
Single-shot mode supported
Automatic start on an HW event (T13HR, for synchronization purposes)
Additional Features
•
•
•
•
•
•
•
Block commutation for Brushless DC-drives implemented
Position detection via Hall-sensor pattern
Automatic rotational speed measurement for block commutation
Integrated error handling
Fast emergency stop without CPU load via external signal (CTRAP)
Control modes for multi-channel AC-drives
Output levels can be selected and adapted to the power stage
Data Sheet
45
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
CCU6 Module Kernel
fSYS
com pare
Channel 0
Channel 3
com pare
3
1
2
2
trap i nput
T13
output select
st art
Hal l i nput
1
Trap
Control
output select
Channel 2
Multichannel
Control
compa re
1
compa re
Interrupts
Channel 1
Deadtime
Control
compa re
T12
capture
TxHR
1
3
2
1
CTRAP
CCPOS0
CCPOS1
CCPOS2
COUT60
CC60
COUT61
CC61
COUT62
CC62
COUT63
Input / Output Control
m c_ccu6_blockdiagram . vsd
Figure 6
CCU6 Block Diagram
Timer T12 can work in capture and/or compare mode for its three channels. The modes
can also be combined. Timer T13 can work in compare mode only. The multi-channel
control unit generates output patterns that can be modulated by timer T12 and/or timer
T13. The modulation sources can be selected and combined for the signal modulation.
Data Sheet
46
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.8
Functional Description
General Purpose Timer (GPT12E) Unit
The GPT12E unit represents a very flexible multifunctional timer/counter structure which
may be used for many different time related tasks such as event timing and counting,
pulse width and duty cycle measurements, pulse generation, or pulse multiplication.
The GPT12E unit incorporates five 16-bit timers which are organized in two separate
modules, GPT1 and GPT2. Each timer in each module may operate independently in a
number of different modes, or may be concatenated with another timer of the same
module.
Each of the three timers T2, T3, T4 of module GPT1 can be configured individually for
one of four basic modes of operation, which are Timer, Gated Timer, Counter, and
Incremental Interface Mode. In Timer Mode, the input clock for a timer is derived from
the system clock, divided by a programmable prescaler, while Counter Mode allows a
timer to be clocked in reference to external events.
Pulse width or duty cycle measurement is supported in Gated Timer Mode, where the
operation of a timer is controlled by the ‘gate’ level on an external input pin. For these
purposes, each timer has one associated port pin (TxIN) which serves as gate or clock
input. The maximum resolution of the timers in module GPT1 is 4 system clock cycles.
The count direction (up/down) for each timer is programmable by software or may
additionally be altered dynamically by an external signal on a port pin (TxEUD) to
facilitate e.g. position tracking.
In Incremental Interface Mode the GPT1 timers (T2, T3, T4) can be directly connected
to the incremental position sensor signals A and B via their respective inputs TxIN and
TxEUD. Direction and count signals are internally derived from these two input signals,
so the contents of the respective timer Tx corresponds to the sensor position. The third
position sensor signal TOP0 can be connected to an interrupt input.
Timer T3 has an output toggle latch (T3OTL) which changes its state on each timer
overflow/underflow. The state of this latch may be output on pin T3OUT e.g. for time out
monitoring of external hardware components. It may also be used internally to clock
timers T2 and T4 for measuring long time periods with high resolution.
In addition to their basic operating modes, timers T2 and T4 may be configured as reload
or capture registers for timer T3. When used as capture or reload registers, timers T2
and T4 are stopped. The contents of timer T3 is captured into T2 or T4 in response to a
signal at their associated input pins (TxIN). Timer T3 is reloaded with the contents of T2
or T4 triggered either by an external signal or by a selectable state transition of its toggle
latch T3OTL. When both T2 and T4 are configured to alternately reload T3 on opposite
state transitions of T3OTL with the low and high times of a PWM signal, this signal can
be constantly generated without software intervention.
Data Sheet
47
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
T3CON.BPS1
f GPT
2n:1
Basic Clock
Interrupt
Request
(T2IRQ)
Aux. Timer T2
T2IN
T2EUD
T2
Mode
Control
U/D
Reload
Capture
Interrupt
Request
(T3IRQ)
T3IN
T3
Mode
Control
T3EUD
Core Timer T3
T3OTL
T3OUT
Toggle
Latch
U/D
Capture
T4IN
T4EUD
T4
Mode
Control
Reload
Aux. Timer T4
U/D
Interrupt
Request
(T4IRQ)
MCA05563
Figure 7
Data Sheet
Block Diagram of GPT1
48
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
With its maximum resolution of 2 system clock cycles, the GPT2 module provides
precise event control and time measurement. It includes two timers (T5, T6) and a
capture/reload register (CAPREL). Both timers can be clocked with an input clock which
is derived from the CPU clock via a programmable prescaler or with external signals. The
count direction (up/down) for each timer is programmable by software or may
additionally be altered dynamically by an external signal on a port pin (TxEUD).
Concatenation of the timers is supported via the output toggle latch (T6OTL) of timer T6,
which changes its state on each timer overflow/underflow.
The state of this latch may be used to clock timer T5, and/or it may be output on pin
T6OUT. The overflows/underflows of timer T6 can additionally be used to clock the
CAPCOM2 timers, and to cause a reload from the CAPREL register.
The CAPREL register may capture the contents of timer T5 based on an external signal
transition on the corresponding port pin (CAPIN), and timer T5 may optionally be cleared
after the capture procedure. This allows the XC226x to measure absolute time
differences or to perform pulse multiplication without software overhead.
The capture trigger (timer T5 to CAPREL) may also be generated upon transitions of
GPT1 timer T3’s inputs T3IN and/or T3EUD. This is especially advantageous when T3
operates in Incremental Interface Mode.
Data Sheet
49
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
T6CON.BPS2
fGPT
2n:1
Basic Clock
Interrupt
Request
(T5IRQ)
GPT2 Timer T5
T5IN
T5
Mode
Control
U/D
Clear
Capture
CAPIN
T3IN/
T3EUD
CAPREL
Mode
Control
GPT2 CAPREL
Interrupt
Request
(CRIRQ)
Reload
Clear
Interrupt
Request
(T6IRQ)
Toggle
FF
T6IN
T6
Mode
Control
GPT2 Timer T6
T6OTL
T6OUT
T6OUF
U/D
MCA05564
Figure 8
Data Sheet
Block Diagram of GPT2
50
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.9
Functional Description
Real Time Clock
The Real Time Clock (RTC) module of the XC226x can be clocked with a selectable
clock signal from internal sources (oscillators or PLL) or external sources (pins).
The RTC basically consists of a chain of divider blocks:
•
•
•
Selectable 32:1 and 8:1 dividers (on - off)
The reloadable 16-bit timer T14
The 32-bit RTC timer block (accessible via registers RTCH and RTCL), made of:
– a reloadable 10-bit timer
– a reloadable 6-bit timer
– a reloadable 6-bit timer
– a reloadable 10-bit timer
All timers count up. Each timer can generate an interrupt request. All requests are
combined to a common node request.
fRTC
:32
M UX
RUN
M UX
Interrupt Sub Node
:8
PRE
REFCLK
CNT
INT0
CNT
INT1
CNT
INT2
RTCINT
CNT
INT3
REL-Register
f CNT
T14REL
10 Bits
6 Bits
6 Bits
10 Bits
T14
10 Bits
6 Bits
6 Bits
10 Bits
T14-Register
CNT-Register
M CB05568B
Figure 9
RTC Block Diagram
Note: The registers associated with the RTC are only affected by a power reset.
Data Sheet
51
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
The RTC module can be used for different purposes:
•
•
•
•
System clock to determine the current time and date
Cyclic time based interrupt, to provide a system time tick independent of CPU
frequency and other resources
48-bit timer for long term measurements
Alarm interrupt upon a defined time
Data Sheet
52
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.10
Functional Description
A/D Converters
For analog signal measurement, up to two 10-bit A/D converters (ADC0, ADC1) with 16
(or 8) multiplexed input channels including a sample and hold circuit have been
integrated on-chip. They use the method of successive approximation. The sample time
(for loading the capacitors) and the conversion time are programmable and can thus be
adjusted to the external circuitry. The A/D converters can also operate in 8-bit conversion
mode, where the conversion time is further reduced.
Several independent conversion result registers, selectable interrupt requests, and
highly flexible conversion sequences provide a high degree of programmability to fulfill
the requirements of the respective application. Both modules can be synchronized to
allow parallel sampling of two input channels.
For applications that require more analog input channels, external analog multiplexers
can be controlled automatically.
For applications that require less analog input channels, the remaining channel inputs
can be used as digital input port pins.
The A/D converters of the XC226x support two types of request sources which can be
triggered by several internal and external events.
•
•
Parallel requests are activated at the same time and then executed in a predefined
sequence.
Queued requests are executed in a user-defined sequence.
In addition, the conversion of a specific channel can be inserted into a running sequence
without disturbing this sequence. All requests are arbitrated according to the priority level
that has been assigned to them.
Data reduction features, such as limit checking or result accumulation, reduce the
number of required CPU accesses and so allow the precise evaluation of analog inputs
(high conversion rate) even at low CPU speed.
The Peripheral Event Controller (PEC) may be used to control the A/D converters or to
automatically store conversion results into a table in memory for later evaluation, without
requiring the overhead of entering and exiting interrupt routines for each data transfer.
Therefore, each A/D converter contains 8 result registers which can be concatenated to
build a result FIFO. Wait-for-read mode can be enabled for each result register to
prevent loss of conversion data.
In order to decouple analog inputs from digital noise and to avoid input trigger noise
those pins used for analog input can be disconnected from the digital input stages under
software control. This can be selected for each pin separately via registers P5_DIDIS
and P15_DIDIS (Port x Digital Input Disable).
The Auto-Power-Down feature of the A/D converters minimizes the power consumption
when no conversion is in progress.
Data Sheet
53
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.11
Functional Description
Universal Serial Interface Channel Modules (USIC)
The XC226x features three USIC modules (USIC0, USIC1, USIC2), each providing two
serial communication channels.
The Universal Serial Interface Channel (USIC) module is based on a generic data shift
and data storage structure which is identical for all supported serial communication
protocols. Each channel supports complete full-duplex operation with a basic data buffer
structure (one transmit buffer and two receive buffer stages). In addition, the data
handling software can use FIFOs.
The protocol part (generation of shift clock/data/control signals) is independent from the
general part and is handled by protocol-specific preprocessors (PPPs).
The USIC’s input/output lines are connected to pins by a pin routing unit, so the inputs
and outputs of each USIC channel can be assigned to different interface pins providing
great flexibility to the application software. All assignments can be done during runtime.
Bus
Buffer & Shift Structure Protocol Preprocessors
Pins
Control 0
DBU
0
PPP_B
DSU
0
PPP_C
PPP_D
Control 1
PPP_A
DBU
1
Pin Routing Shell
Bus Interface
PPP_A
PPP_B
DSU
1
PPP_C
PPP_D
fsys
Fractional
Dividers
Baud rate
Generators
USIC_basic.vsd
Figure 10
General Structure of a USIC Module
The regular structure of the USIC module brings the following advantages:
•
•
•
Higher flexibility through configuration with same look-and-feel for data management
Reduced complexity for low-level drivers serving different protocols
Wide range of protocols, but improved performances (baud rate, buffer handling)
Data Sheet
54
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
Target Protocols
Each USIC channel can receive and transmit data frames with a selectable data word
width from 1 to 16 bits in each of the following protocols:
•
•
•
•
•
UART (asynchronous serial channel)
– maximum baud rate: fSYS / 4
– data frame length programmable from 1 to 63 bits
– MSB or LSB first
LIN Support (Local Interconnect Network)
– maximum baud rate: fSYS / 16
– checksum generation under software control
– baud rate detection possible by built-in capture event of baud rate generator
SSC/SPI/QSPI (synchronous serial channel with or without data buffer)
– maximum baud rate in slave mode: fSYS
– maximum baud rate in master mode: fSYS / 2
– number of data bits programmable from 1 to 63, more with explicit stop condition
– MSB or LSB first
– optional control of slave select signals
IIC (Inter-IC Bus)
– supports baud rates of 100 kbit/s and 400 kbit/s
IIS (Inter-IC Sound Bus)
– maximum baud rate: fSYS / 2 for transmitter, fSYS for receiver
Note: Depending on the selected functions (such as digital filters, input synchronization
stages, sample point adjustment, etc.), the maximum reachable baud rate can be
limited. Please also take care about additional delays, such as internal or external
propagation delays and driver delays (e.g. for collision detection in UART mode,
for IIC, etc.).
Data Sheet
55
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.12
Functional Description
MultiCAN Module
The MultiCAN module contains up to five independently operating CAN nodes with FullCAN functionality which are able to exchange Data and Remote Frames via a gateway
function. Transmission and reception of CAN frames is handled in accordance with CAN
specification V2.0 B (active). Each CAN node can receive and transmit standard frames
with 11-bit identifiers as well as extended frames with 29-bit identifiers.
All CAN nodes share a common set of up to 128 message objects. Each message object
can be individually allocated to one of the CAN nodes. Besides serving as a storage
container for incoming and outgoing frames, message objects can be combined to build
gateways between the CAN nodes or to setup a FIFO buffer.
The message objects are organized in double-chained linked lists, where each CAN
node has its own list of message objects. A CAN node stores frames only into message
objects that are allocated to its own message object list, and it transmits only messages
belonging to this message object list. A powerful, command-driven list controller
performs all message object list operations.
MultiCAN Module Kernel
Clock
Control
Address
Decoder
CAN
Node 4
fCAN
Message
Object
Buffer
128
Objects
.
.
.
Linked
List
Control
CAN
Node 1
CAN
Node 0
Interrupt
Control
TXDC4
RXDC4
.
.
.
.
.
.
TXDC1
RXDC1
Port
Control
TXDC0
RXDC0
CAN Control
mc_mcan_block5.vsd
Figure 11
Data Sheet
Block Diagram of MultiCAN Module
56
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Functional Description
MultiCAN Features
•
•
•
•
•
•
•
•
•
•
CAN functionality conforms to CAN specification V2.0 B active for each CAN node
(compliant to ISO 11898)
Five independent CAN nodes
128 independent message objects (shared by the CAN nodes)
Dedicated control registers for each CAN node
Data transfer rate up to 1 Mbit/s, individually programmable for each node
Flexible and powerful message transfer control and error handling capabilities
Full-CAN functionality for message objects:
– Can be assigned to one of the CAN nodes
– Configurable as transmit or receive objects, or as message buffer FIFO
– Handle 11-bit or 29-bit identifiers with programmable acceptance mask for filtering
– Remote Monitoring Mode, and frame counter for monitoring
Automatic Gateway Mode support
16 individually programmable interrupt nodes
Analyzer mode for CAN bus monitoring
Data Sheet
57
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.13
Functional Description
Watchdog Timer
The Watchdog Timer represents one of the fail-safe mechanisms which have been
implemented to prevent the controller from malfunctioning for longer periods of time.
The Watchdog Timer is always enabled after a reset of the chip, and can be disabled
and enabled at any time by executing instructions DISWDT and ENWDT. Thus, the
chip’s start-up procedure is always monitored. The software has to be designed to
service the Watchdog Timer before it overflows. If, due to hardware or software related
failures, the software fails to do so, the Watchdog Timer overflows and generates a
prewarning interrupt and then a reset request.
The Watchdog Timer is a 16-bit timer, clocked with the system clock divided by 16,384
or 256. The Watchdog Timer register is set to a prespecified reload value (stored in
WDTREL) in order to allow further variation of the monitored time interval. Each time it
is serviced by the application software, the Watchdog Timer is reloaded and the
prescaler is cleared.
Thus, time intervals between 3.9 µs and 16.3 s can be monitored (@ 66 MHz).
The default Watchdog Timer interval after power-up is 6.5 ms (@ 10 MHz).
Data Sheet
58
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.14
Functional Description
Clock Generation
The Clock Generation Unit can generate the system clock signal fSYS for the XC226x with
high flexibility from several external or internal clock sources.
•
•
•
•
External clock signals on pad- or core-voltage level
External crystal controlled by on-chip oscillator
On-chip oscillator (IOSC) for operation without crystal
Wake-up oscillator (ultra-low power) to further reduce power consumption
The programmable on-chip PLL with multiple prescalers generates a clock signal for
maximum system performance from standard crystals or from the on-chip oscillator. See
also Section 4.4.1.
The Oscillator Watchdog (OWD) generates an interrupt if the crystal oscillator frequency
falls below a certain limit or stops completely. In this case, the system can be supplied
with an emergency clock to enable operation even after an external clock failure.
All available clock signals can also be output on one of two selectable pins.
Data Sheet
59
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.15
Functional Description
Parallel Ports
The XC226x provides up to 75 I/O lines which are organized into 7 input/output ports and
2 input ports. All port lines are bit-addressable, and all input/output lines can be
individually (bit-wise) configured via port control registers. This configuration selects the
direction (input/output), push/pull or open-drain operation, activation of pull devices, and
edge characteristics (shape) and driver characteristics (output current) of the port
drivers. The I/O ports are true bidirectional ports which are switched to high impedance
state when configured as inputs. During the internal reset, all port pins are configured as
inputs without pull devices active.
All port lines have programmable alternate input or output functions associated with
them. These alternate functions can be assigned to various port pins to support the
optimal utilization for a given application. For this reason, certain functions appear
several times in Table 7.
All port lines that are not used for these alternate functions may be used as general
purpose I/O lines.
Table 7
Summary of the XC226x’s Parallel Ports
Port
Width
Alternate Functions
Port 0
8
Address lines,
Serial interface lines of USIC1, CAN0, and CAN1,
Input/Output lines for CCU61
Port 1
8
Address lines,
Serial interface lines of USIC1 and USIC2,
Input/Output lines for CCU62,
OCDS control, interrupts
Port 2
13
Address and/or data lines, bus control,
Serial interface lines of USIC0, CAN0, and CAN1,
Input/Output lines for CCU60, CCU63, and CAPCOM2,
Timer control signals,
JTAG, interrupts, system clock output
Port 4
4
Chip select signals,
Serial interface lines of CAN2,
Input/Output lines for CAPCOM2,
Timer control signals
Port 5
11
Analog input channels to ADC0,
Input/Output lines for CCU6x,
Timer control signals,
JTAG, OCDS control, interrupts
Data Sheet
60
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 7
Functional Description
Summary of the XC226x’s Parallel Ports (cont’d)
Port
Width
Alternate Functions
Port 6
3
ADC control lines,
Serial interface lines of USIC1,
Timer control signals,
OCDS control
Port 7
5
ADC control lines,
Serial interface lines of USIC0 and CAN4,
Input/Output lines for CCU62,
Timer control signals,
JTAG, OCDS control,system clock output
Port 10
16
Address and/or data lines, bus control,
Serial interface lines of USIC0, USIC1, CAN2, CAN3, and CAN4,
Input/Output lines for CCU60,
JTAG, OCDS control
Port 15
5
Analog input channels to ADC1,
Timer control signals
Data Sheet
61
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.16
Functional Description
Power Management
The XC226x provides several means to control the power it consumes either at a given
time or averaged over a certain timespan. Three mechanisms can be used (partly in
parallel):
•
•
•
Supply Voltage Management allows the temporary reduction of the supply voltage
of major parts of the logic, or even the complete disconnection. This drastically
reduces the power consumed because of leakage current, in particular at high
temperature.
Several power reduction modes provide the optimal balance of power reduction and
wake-up time.
Clock Generation Management controls the frequency of internal and external
clock signals. While the clock signals for currently inactive parts of logic are disabled
automatically, the user can reduce the XC226x’s system clock frequency which
drastically reduces the consumed power.
External circuitry can be controlled via the programmable frequency output EXTCLK.
Peripheral Management permits temporary disabling of peripheral modules. Each
peripheral can separately be disabled/enabled. Also the CPU can be switched off
while the peripherals can continue to operate.
Wake-up from power reduction modes can be triggered either externally by signals
generated by the external system, or internally by the on-chip wake-up timer, which
supports intermittent operation of the XC226x by generating cyclic wake-up signals. This
offers full performance to quickly react on action requests while the intermittent sleep
phases greatly reduce the average power consumption of the system.
Note: When selecting the supply voltage and the clock source and generation method,
the required parameters must be carefully written to the respective bitfields, to
avoid unintended intermediate states. Recommended sequences are provided
which ensure the intended operation of power supply system and clock system.
Data Sheet
62
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
3.17
Functional Description
Instruction Set Summary
Table 8 lists the instructions of the XC226x in a condensed way.
The various addressing modes that can be used with a specific instruction, the operation
of the instructions, parameters for conditional execution of instructions, and the opcodes
for each instruction can be found in the “Instruction Set Manual”.
This document also provides a detailed description of each instruction.
Table 8
Instruction Set Summary
Mnemonic
Description
Bytes
ADD(B)
Add word (byte) operands
2/4
ADDC(B)
Add word (byte) operands with Carry
2/4
SUB(B)
Subtract word (byte) operands
2/4
SUBC(B)
Subtract word (byte) operands with Carry
2/4
MUL(U)
(Un)Signed multiply direct GPR by direct GPR
(16- × 16-bit)
2
DIV(U)
(Un)Signed divide register MDL by direct GPR (16-/16-bit) 2
DIVL(U)
(Un)Signed long divide reg. MD by direct GPR (32-/16-bit) 2
CPL(B)
Complement direct word (byte) GPR
2
NEG(B)
Negate direct word (byte) GPR
2
AND(B)
Bitwise AND, (word/byte operands)
2/4
OR(B)
Bitwise OR, (word/byte operands)
2/4
XOR(B)
Bitwise exclusive OR, (word/byte operands)
2/4
BCLR/BSET
Clear/Set direct bit
2
BMOV(N)
Move (negated) direct bit to direct bit
4
BAND/BOR/BXOR AND/OR/XOR direct bit with direct bit
4
BCMP
Compare direct bit to direct bit
4
BFLDH/BFLDL
Bitwise modify masked high/low byte of bit-addressable
direct word memory with immediate data
4
CMP(B)
Compare word (byte) operands
2/4
CMPD1/2
Compare word data to GPR and decrement GPR by 1/2
2/4
CMPI1/2
Compare word data to GPR and increment GPR by 1/2
2/4
PRIOR
Determine number of shift cycles to normalize direct
word GPR and store result in direct word GPR
2
SHL/SHR
Shift left/right direct word GPR
2
Data Sheet
63
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 8
Functional Description
Instruction Set Summary (cont’d)
Mnemonic
Description
Bytes
ROL/ROR
Rotate left/right direct word GPR
2
ASHR
Arithmetic (sign bit) shift right direct word GPR
2
MOV(B)
Move word (byte) data
2/4
MOVBS/Z
Move byte operand to word op. with sign/zero extension
2/4
JMPA/I/R
Jump absolute/indirect/relative if condition is met
4
JMPS
Jump absolute to a code segment
4
JB(C)
Jump relative if direct bit is set (and clear bit)
4
JNB(S)
Jump relative if direct bit is not set (and set bit)
4
CALLA/I/R
Call absolute/indirect/relative subroutine if condition is met 4
CALLS
Call absolute subroutine in any code segment
4
PCALL
Push direct word register onto system stack and call
absolute subroutine
4
TRAP
Call interrupt service routine via immediate trap number
2
PUSH/POP
Push/pop direct word register onto/from system stack
2
SCXT
Push direct word register onto system stack and update
register with word operand
4
RET(P)
Return from intra-segment subroutine
(and pop direct word register from system stack)
2
RETS
Return from inter-segment subroutine
2
RETI
Return from interrupt service subroutine
2
SBRK
Software Break
2
SRST
Software Reset
4
IDLE
Enter Idle Mode
4
PWRDN
Unused instruction1)
4
SRVWDT
Service Watchdog Timer
4
DISWDT/ENWDT
Disable/Enable Watchdog Timer
4
EINIT
End-of-Initialization Register Lock
4
ATOMIC
Begin ATOMIC sequence
2
EXTR
Begin EXTended Register sequence
2
EXTP(R)
Begin EXTended Page (and Register) sequence
2/4
EXTS(R)
Begin EXTended Segment (and Register) sequence
2/4
Data Sheet
64
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 8
Functional Description
Instruction Set Summary (cont’d)
Mnemonic
Description
Bytes
NOP
Null operation
2
CoMUL/CoMAC
Multiply (and accumulate)
4
CoADD/CoSUB
Add/Subtract
4
Co(A)SHR
(Arithmetic) Shift right
4
CoSHL
Shift left
4
CoLOAD/STORE
Load accumulator/Store MAC register
4
CoCMP
Compare
4
CoMAX/MIN
Maximum/Minimum
4
CoABS/CoRND
Absolute value/Round accumulator
4
CoMOV
Data move
4
CoNEG/NOP
Negate accumulator/Null operation
4
1) The Enter Power Down Mode instruction is not used in the XC226x, due to the enhanced power control
scheme. PWRDN will be correctly decoded, but will trigger no action.
Data Sheet
65
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
4
Electrical Parameters
Electrical Parameters
The operating range for the XC226x is defined by its electrical parameters. For proper
operation the indicated limitations must be respected when designing a system.
Attention: The parameters and values listed in the following sections of this
Preliminary Data Sheet are preliminary and will be adjusted and
amended after the complete device characterization has been
completed.
4.1
General Parameters
These parameters are valid for all subsequent descriptions, unless otherwise noted.
Table 9
Absolute Maximum Rating Parameters
Parameter
Symbol Values
Min.
Typ.
Max.
Unit Note /
Test Condition
TST
Junction temperature
TJ
Voltage on VDDI pins with VDDIM,
VDDI1
respect to ground (VSS)
Voltage on VDDP pins with VDDPA,
respect to ground (VSS)
VDDPB
Voltage on any pin with
VIN
respect to ground (VSS)
-65
–
150
°C
–
-40
–
150
°C
under bias
-0.5
–
1.65
V
–
-0.5
–
6.0
V
–
-0.5
–
VDDP
V
VIN < VDDPmax
Input current on any pin
during overload condition
–
-10
–
10
mA
–
Absolute sum of all input
currents during overload
condition
–
–
–
|100|
mA
–
Storage temperature
+ 0.5
Note: Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in
the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
During absolute maximum rating overload conditions (VIN > VDDP or VIN < VSS) the
voltage on VDDP pins with respect to ground (VSS) must not exceed the values
defined by the absolute maximum ratings.
Data Sheet
66
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
Operating Conditions
The following operating conditions must not be exceeded to ensure correct operation of
the XC226x. All parameters specified in the following sections refer to these operating
conditions, unless otherwise noticed.
Table 10
Operating Condition Parameters
Parameter
Symbol
Digital core supply voltage VDDI
(if supplied externally)
Values
Min.
Typ.
Max.
Unit Note /
Test Condition
1.4
–
1.6
V
-10
–
+10
mV
Core Supply Voltage
Difference
∆VDDI
Digital supply voltage for
IO pads and voltage
regulators,
upper voltage range
VDDPA,
VDDPB
4.5
–
5.5
V
2)
Digital supply voltage for
IO pads and voltage
regulators,
lower voltage range
VDDPA,
VDDPB
3.0
–
4.5
V
2)
-0.5
–
–
V
VDDP - VDDI3)
VDDIM - VDDI1
1)
Supply Voltage Difference ∆VDD
Digital ground voltage
VSS
0
–
0
V
Reference
voltage
Overload current
IOV
-5
–
5
mA
Per IO pin4)5)
-2
–
5
mA
Per analog input
pin4)5)
KOVA
–
–
1.0 ×
10-4
–
IOV > 0
Overload negative current KOVA
coupling factor for analog
inputs6)
–
–
1.5 ×
10-3
–
IOV < 0
KOVD
–
–
5.0 ×
10-3
–
IOV > 0
Overload negative current KOVD
coupling factor for digital
I/O pins6)
–
–
1.0 ×
10-2
–
IOV < 0
Overload positive current
coupling factor for analog
inputs6)
Overload positive current
coupling factor for digital
I/O pins6)
Data Sheet
67
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 10
Electrical Parameters
Operating Condition Parameters (cont’d)
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit Note /
Test Condition
Absolute sum of overload
currents
Σ|IOV|
–
–
50
mA
5)
External Pin Load
Capacitance
CL
–
20
–
pF
Pin drivers in
default mode7)
Voltage Regulator Buffer
Capacitance
CEVR
–
680
–
nF
For each core
domain8)
Ambient temperature
TA
–
–
–
°C
See Table 1
1) In case both core power domains are clocked, the difference between the power supply voltages must be less
than 10mV. This condition imposes additional constraints when using external power supplies. In order to
supply both core power domains, two independent external voltage regulators may not be used. The simplest
possibility is to supply both power domains directly via a single external power supply.
2) Performance of pad drivers, A/D Converter, and Flash module depends on VDDP.
3) This limitation must be fulfilled under all operating conditions including power-ramp-up, power-ramp-down,
and power-save modes, if VDDI is supplied externally.
4) Overload conditions occur if the standard operating conditions are exceeded, i.e. the voltage on any pin
exceeds the specified range: VOV > VIHmax (IOV > 0) or VOV < VILmin (IOV < 0). The absolute sum of input
overload currents on all pins may not exceed 50 mA. The supply voltages must remain within the specified
limits. Proper operation under overload conditions depends on the application.
Overload conditions must not occur on pin XTAL1 (powered by VDDI).
5) Not subject to production test - verified by design/characterization.
6) An overload current (IOV) through a pin injects a certain error current (IINJ) into the adjacent pins. This error
current adds to the respective pin’s leakage current (IOZ). The amount of error current depends on the overload
current and is defined by the overload coupling factor KOV. The polarity of the injected error current is inverse
compared to the polarity of the overload current that produces it.
The total current through a pin is |ITOT| = |IOZ| + (|IOV| × KOV). The additional error current may distort the input
voltage on analog inputs.
7) The timing is valid for pin drivers operating in default current mode (selected after reset). Reducing the output
current may lead to increased delays or reduced driving capability (CL).
8) To ensure the stability of the voltage regulators each core voltage domain must be buffered with a ceramic
capacitor. For domain M a 680 nF capacitor is recommended, for domain 1 three 220 nF capacitors are
recommended. All buffer capacitors must be connected als close to the VDDI pins as possible to keep the
resistance of the board tracks below 2 Ω.
Data Sheet
68
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
Parameter Interpretation
The parameters listed in the following partly represent the characteristics of the XC226x
and partly its demands on the system. To aid in interpreting the parameters right, when
evaluating them for a design, they are marked in column “Symbol”:
CC (Controller Characteristics):
The logic of the XC226x will provide signals with the respective characteristics.
SR (System Requirement):
The external system must provide signals with the respective characteristics to the
XC226x.
Data Sheet
69
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
4.2
Electrical Parameters
DC Parameters
These parameters are static or average values, which may be exceeded during
switching transitions (e.g. output current).
The XC226x can operate within a wide supply voltage range from 3.0 V to 5.5 V.
However, during operation this supply voltage must not vary within the complete
operating voltage range, but must remain within a certain band of 10% of the chosen
nominal supply voltage.
For this reason and because the electrical behaviour partly depends on the supply
voltage, the parameters are specified twice for the upper and the lower voltage area.
During operation, the supply voltages may only change with a maximum speed of
dV/dt < 1 V/ms.
The leakage currents strongly depend on the operating temperature and the actual
voltage level at the respective pin. The maximum values given in the following tables
apply under worst case conditions, i.e. maximum temperature and an input level equal
to the supply voltage.
The actual value for the leakage current can be determined by evaluating the respective
leakage derating formula (see tables) using values from the actual application.
The pads of the XC226x are designed to operate in various driver modes. The DC
parameter specifications refer to the current limits given in Table 11.
Table 11
Current Limits for Port Output Drivers
Port Output Driver
Mode
Maximum Output Current
(IOLmax, -IOHmax)1)
Nominal Output Current
(IOLnom, -IOHnom)
VDDP ≥ 4.5 V
VDDP < 4.5 V
VDDP ≥ 4.5 V
VDDP < 4.5 V
Strong driver
10 mA
10 mA
2.5 mA
2.5 mA
Medium driver
4.0 mA
2.5 mA
1.0 mA
1.0 mA
Weak driver
0.5 mA
0.5 mA
0.1 mA
0.1 mA
1) An output current above |IOXnom| may be drawn from up to three pins at the same time.
For any group of 16 neighboring output pins the total output current in each direction (ΣIOL and Σ-IOH) must
remain below 50 mA.
Data Sheet
70
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
4.2.1
Electrical Parameters
DC Parameters for Upper Voltage Area
These parameters apply to the upper IO voltage area of 4.5 V ≤ VDDP ≤ 5.5 V.
Table 12
DC Characteristics for 4.5 V ≤ VDDP ≤ 5.5 V
(Operating Conditions apply)1)
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit Note /
Test Condition
-0.3
–
0.3 ×
V
–
Input low voltage
(all except XTAL1)
VIL SR
Input low voltage for
XTAL1
VILC SR -1.7 +
VDDI
VIH SR 0.7 ×
VDDP
VIHC SR 0.7 ×
VDDI
Input high voltage
(all except XTAL1)
Input high voltage for
XTAL1
Input Hysteresis3)
Output low voltage
Output low voltage
Output high voltage6)
VDDP
–
0.3 ×
V
–
–
VDDI
VDDP
V
–
1.7
V
2)
HYS CC 0.11
–
× VDDP
–
V
VDD in [V],
VOL CC –
VOL CC –
VOH CC VDDP
–
1.0
V
–
0.4
V
–
–
V
IOL ≤ IOLmax4)
IOL ≤ IOLnom4) 5)
IOH ≥ IOHmax4)
–
–
V
IOH ≥ IOHnom4) 5)
+ 0.3
–
Series
resistance = 0 Ω
- 1.0
Output high voltage6)
VOH CC VDDP
- 0.4
Input leakage current
(Port 5, Port 15)7)
IOZ1 CC –
±200
–
nA
0 V < VIN < VDDP
Input leakage current
(all other)7)8)
IOZ2 CC –
±2
±5
µA
Input leakage current
(all other)7)8)
IOZ2 CC –
±10
±30
µA
–
–
-30
µA
-220
–
–
µA
TJ ≤ 110°C,
0.45 V < VIN
< VDDP
TJ ≤ 150°C,
0.45 V < VIN
< VDDP
VOUT ≥ VIHmin
VOUT ≤ VILmax
Level inactive hold current ILHI
Level active hold current
Data Sheet
ILHA
71
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 12
Electrical Parameters
DC Characteristics for 4.5 V ≤ VDDP ≤ 5.5 V (cont’d)
(Operating Conditions apply)1)
Parameter
XTAL1 input current
Pin capacitance9)
(digital inputs/outputs)
Symbol
IIL CC
CIO CC
Values
Min.
Typ.
Max.
Unit Note /
Test Condition
–
–
±20
µA
–
–
10
pF
0 V < VIN < VDDI
1) Keeping signal levels within the limits specified in this table, ensures operation without overload conditions.
For signal levels outside these specifications, also refer to the specification of the overload current IOV.
2) Overload conditions must not occur on pin XTAL1.
3) Not subject to production test - verified by design/characterization. Hysteresis is implemented to avoid meta
stable states and switching due to internal ground bounce. It cannot suppress switching due to external system
noise under all conditions.
4) The maximum deliverable output current of a port driver depends on the selected output driver mode, see
Table 11, Current Limits for Port Output Drivers. The limit for pin groups must be respected.
5) As a rule, with decreasing output current the output levels approach the respective supply level (VOL→VSS,
VOH→VDDP). However, only the levels for nominal output currents are verified.
6) This specification is not valid for outputs which are switched to open drain mode. In this case the respective
output will float and the voltage results from the external circuitry.
7) An additional error current (IINJ) will flow if an overload current flows through an adjacent pin. Please refer to
the definition of the overload coupling factor KOV.
8) The given values are worst-case values. In the production test, this leakage current value is only tested at
125°C, other values are ensured via correlation. For derating, please refer to the following descriptions:
Leakage derating depending on temperature (TJ = junction temperature [°C]):
IOZ = 0.009 × e(0.054×TJ) [µA]. For example, at a temperature of 130°C the resulting leakage current is 10.07 µA.
Leakage derating depending on voltage level (DV = VDDP - VPIN [V]):
IOZ = IOZtempmax - (1.6 × DV) [µA]
The shown voltage derating formula is an approximation which applies for maximum temperature.
Pin P2.8 is connected to two pads (additionally the high-speed clock pad), so it sees twice the normal leakage.
9) Not subject to production test - verified by design/characterization.
Pin P2.8 is connected to two pads (additionally the high-speed clock pad), so it sees twice the normal
capacitance.
Data Sheet
72
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
4.2.2
Electrical Parameters
DC Parameters for Lower Voltage Area
These parameters apply to the lower IO voltage area of 3.0 V ≤ VDDP ≤ 4.5 V.
Table 13
DC Characteristics for 3.0 V ≤ VDDP ≤ 4.5 V
(Operating Conditions apply)1)
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit Note /
Test Condition
-0.3
–
0.3 ×
V
–
Input low voltage
(all except XTAL1)
VIL SR
Input low voltage for
XTAL1
VILC SR -1.7 +
VDDI
VIH SR 0.7 ×
VDDP
VIHC SR 0.7 ×
VDDI
Input high voltage
(all except XTAL1)
Input high voltage for
XTAL1
Input Hysteresis3)
Output low voltage
Output low voltage
Output high voltage6)
VDDP
–
0.3 ×
V
–
–
VDDI
VDDP
V
–
1.7
V
2)
HYS CC 0.11
–
× VDDP
–
V
VDD in [V],
VOL CC –
VOL CC –
VOH CC VDDP
–
1.0
V
–
0.4
V
–
–
V
IOL ≤ IOLmax4)
IOL ≤ IOLnom4) 5)
IOH ≥ IOHmax4)
–
–
V
IOH ≥ IOHnom4) 5)
+ 0.3
–
Series
resistance = 0 Ω
- 1.0
Output high voltage6)
VOH CC VDDP
- 0.4
Input leakage current
(Port 5, Port 15)7)
IOZ1 CC –
±100
–
nA
0 V < VIN < VDDP
Input leakage current
(all other)7)8)
IOZ2 CC –
±1
±2.5
µA
Input leakage current
(all other)7)8)
IOZ2 CC –
±5
±15
µA
–
–
-10
µA
-150
–
–
µA
TJ ≤ 110°C,
0.45 V < VIN
< VDDP
TJ ≤ 150°C,
0.45 V < VIN
< VDDP
VOUT ≥ VIHmin
VOUT ≤ VILmax
Level inactive hold current ILHI
Level active hold current
Data Sheet
ILHA
73
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 13
Electrical Parameters
DC Characteristics for 3.0 V ≤ VDDP ≤ 4.5 V (cont’d)
(Operating Conditions apply)1)
Parameter
XTAL1 input current
Pin capacitance9)
(digital inputs/outputs)
Symbol
IIL CC
CIO CC
Values
Min.
Typ.
Max.
Unit Note /
Test Condition
–
–
±20
µA
–
–
10
pF
0 V < VIN < VDDI
1) Keeping signal levels within the limits specified in this table, ensures operation without overload conditions.
For signal levels outside these specifications, also refer to the specification of the overload current IOV.
2) Overload conditions must not occur on pin XTAL1.
3) Not subject to production test - verified by design/characterization. Hysteresis is implemented to avoid meta
stable states and switching due to internal ground bounce. It cannot suppress switching due to external system
noise under all conditions.
4) The maximum deliverable output current of a port driver depends on the selected output driver mode, see
Table 11, Current Limits for Port Output Drivers. The limit for pin groups must be respected.
5) As a rule, with decreasing output current the output levels approach the respective supply level (VOL→VSS,
VOH→VDDP). However, only the levels for nominal output currents are verified.
6) This specification is not valid for outputs which are switched to open drain mode. In this case the respective
output will float and the voltage results from the external circuitry.
7) An additional error current (IINJ) will flow if an overload current flows through an adjacent pin. Please refer to
the definition of the overload coupling factor KOV.
The leakage current value is not tested in the lower voltage range, but only in the upper voltage range. This
parameter is ensured via correlation.
8) The given values are worst-case values. In the production test, this leakage current value is only tested at
125°C, other values are ensured via correlation. For derating, please refer to the following descriptions:
Leakage derating depending on temperature (TJ = junction temperature [°C]):
IOZ = 0.005 × e(0.054×TJ) [µA]. For example, at a temperature of 130°C the resulting leakage current is 5.6 µA.
Leakage derating depending on voltage level (DV = VDDP - VPIN [V]):
IOZ = IOZtempmax - (1.3 × DV) [µA]
The shown voltage derating formula is an approximation which applies for maximum temperature.
Pin P2.8 is connected to two pads (additionally the high-speed clock pad), so it sees twice the normal leakage.
9) Not subject to production test - verified by design/characterization.
Pin P2.8 is connected to two pads (additionally the high-speed clock pad), so it sees twice the normal
capacitance.
Data Sheet
74
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
4.2.3
Electrical Parameters
Power Consumption
The amount of power that is consumed by the XC226x depends on several factors, such
as supply voltage, operating frequency, amount of active circuitry, and operating
temperature. Part of this depends on the device’s activity (switching current), part of this
is independent (leakage current). Therefore, the leakage current must be added to all
other (frequency-dependent) parameters.
For additional information, please refer to Section 5.2, Thermal Considerations.
Table 14
Power Consumption XC226x (Operating Conditions apply)
Parameter
SymValues
bol
Min. Typ.
Max.
Unit Note /
Test Condition
Supply current caused by
leakage1)
(DMP_1 powered)
IDDL
–
600,000 tbd
× e-α
mA
Supply current caused by
leakage1)
(DMP_1 switched off)
IDDL
–
500,000 tbd
× e-α
µA
Power supply current
IDDP
(active) with all peripherals
active and EVVRs on
–
10 +
tbd
0.6×fSYS
mA
VDDP = VDDPmax2)
α=
5000 / (273 + TJ),
TJ in [°C]
VDDP = VDDPmax2)
α=
3000 / (273 + TJ),
TJ in [°C]
Active Mode3)
fSYSin [MHz]
1) The supply current caused by leakage mainly depends on the junction temperature (see Figure 12) and the
supply voltage. The temperature difference between the junction temperature TJ and the ambient temperature
TA must be taken into account. As this fraction of the supply current does not depend on the device’s activity,
it must be added to each other power consumption parameter.
2) All inputs (including pins configured as inputs) at 0 V to 0.1 V or at VDDP - 0.1 V to VDDP, all outputs (including
pins configured as outputs) disconnected. This parameter is tested at 25 °C and is valid for TJ ≥ 25 °C.
3) The pad supply voltage pins (VDDP) provide the input current for the on-chip EVVRs and the current consumed
by the pin output drivers. A small amount of current is consumed because the drivers’ input stages are
switched.
Data Sheet
75
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
IDDL [mA]
6
DMP_1 ON
4
2
DMP_1 off
-50
0
50
100
T J [°C]
150
MC_XC2X_IDDL
Figure 12
Leakage Supply Current as a Function of Temperature
Data Sheet
76
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
IDDtyp
IDD [mA]
100
80
60
50
40
30
20
10
20
60
40
80
fSYS [MHz]
MC_XC2X_IDD
Figure 13
Data Sheet
Supply Current in Active Mode as a Function of Frequency
77
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
4.3
Electrical Parameters
Analog/Digital Converter Parameters
These parameters describe how the optimum ADC performance can be reached.
Table 15
A/D Converter Characteristics (Operating Conditions apply)
Parameter
Symbol
Limit Values
Max.
Unit Test
Condition
SR VAGND
+ 1.0
VDDPA
V
1)
SR VSS
- 0.05
VAREF
V
–
SR VAGND
VAREF
V
2)
16.5
MHz
3)
CC (17 + STC) × tADCI
–
–
–
–
Min.
Analog reference supply
Analog reference ground
VAREF
VAGND
Analog input voltage range VAIN
fADCI
Conversion time for 10-bit tC10
Basic clock frequency
4)
0.5
+ 0.05
- 1.0
result
Conversion time for 8-bit
result4)
tC8
CC (15 + STC) × tADCI
Total unadjusted error
TUE
CC –
±2
LSB
1)
Total capacitance
of an analog input
CAINT
CC –
15
pF
5)
Switched capacitance
of an analog input
CAINS
CC –
7
pF
5)
Resistance of
the analog input path
RAIN
CC –
1.5
kΩ
5)
Total capacitance
of the reference input
CAREFT CC –
20
pF
5)
Switched capacitance
of the reference input
CAREFS CC –
20
pF
5)
Resistance of
the reference input path
RAREF
2
kΩ
5)
CC –
1) TUE is tested at VAREFx = VDDPA, VAGND = 0 V. It is verified by design for all other voltages within the defined
voltage range.
The specified TUE is valid only, if the absolute sum of input overload currents on Port 5 or Port 15 pins (see
IOV specification) does not exceed 10 mA, and if VAREF and VAGND remain stable during the respective period
of time.
2) VAIN may exceed VAGND or VAREFx up to the absolute maximum ratings. However, the conversion result in these
cases will be X000H or X3FFH, respectively.
3) The limit values for fADCI must not be exceeded when selecting the peripheral frequency and the prescaler
setting.
Data Sheet
78
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
4) This parameter includes the sample time (also the additional sample time specified by STC), the time for
determining the digital result and the time to load the result register with the conversion result.
Values for the basic clock tADCI depend on programming and can be taken from Table 16.
5) Not subject to production test - verified by design/characterization.
The given parameter values cover the complete operating range. Under relaxed operating conditions
(temperature, supply voltage) reduced values can be used for calculations. At room temperature and nominal
supply voltage the following typical values can be used:
CAINTtyp = 12 pF, CAINStyp = 5 pF, RAINtyp = 1.0 kΩ, CAREFTtyp = 15 pF, CAREFStyp = 10 pF, RAREFtyp = 1.0 kΩ.
RSource
V AIN
R AIN, On
C AINT - C AINS
C Ext
A/D Converter
CAINS
MCS05570
Figure 14
Data Sheet
Equivalent Circuitry for Analog Inputs
79
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
Sample time and conversion time of the XC226x’s A/D Converters are programmable.
The above timing can be calculated using Table 16.
The limit values for fADCI must not be exceeded when selecting the prescaler value.
Table 16
A/D Converter Computation Table
GLOBCTR.5-0
(DIVA)
A/D Converter
Basic Clock fADCI
INPCRx.7-0
(STC)
000000B
fSYS
fSYS / 2
fSYS / 3
fSYS / (DIVA+1)
fSYS / 63
fSYS / 64
00H
000001B
000010B
:
111110B
111111B
01H
02H
:
FEH
FFH
Sample Time
tS
tADCI × 2
tADCI × 3
tADCI × 4
tADCI × (STC+2)
tADCI × 256
tADCI × 257
Converter Timing Example:
Assumptions:
Basic clock
Sample time
fSYS
fADCI
tS
= 66 MHz (i.e. tSYS = 15.2 ns), DIVA = 03H, STC = 00H
= fSYS / 4 = 16.5 MHz, i.e. tADCI = 60.6 ns
= tADCI × 2 = 121 ns
Conversion 10-bit:
tC10
= 17 × tADCI = 17 × 60.6 ns = 1.03 µs
Conversion 8-bit:
tC8
= 15 × tADCI = 15 × 60.6 ns = 0.91 µs
Converter Timing Example:
Assumptions:
Basic clock
Sample time
fSYS
fADCI
tS
= 40 MHz (i.e. tSYS = 25 ns), DIVA = 02H, STC = 03H
= fSYS / 3 = 13.3 MHz, i.e. tADCI = 75 ns
= tADCI × 5 = 375 ns
Conversion 10-bit:
tC10
= 20 × tADCI = 20 × 75 ns = 1.5 µs
Conversion 8-bit:
tC8
Data Sheet
= 18 × tADCI = 18 × 75 ns = 1.35 µs
80
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
4.4
Electrical Parameters
AC Parameters
These parameters describe the dynamic behavior of the XC226x.
4.4.1
Definition of Internal Timing
The internal operation of the XC226x is controlled by the internal system clock fSYS.
Because the system clock signal fSYS can be generated from several internal and
external sources via different mechanisms, the duration of system clock periods (TCSs)
and their variation (and also the derived external timing) depend on the used mechanism
to generate fSYS. This influence must be regarded when calculating the timings for the
XC226x.
Phase Locked Loop Operation (1:N)
f IN
f SYS
TCS
Direct Clock Drive (1:1)
f IN
f SYS
TCS
Prescaler Operation (N:1)
f IN
f SYS
TCS
M C_XC2X_CLOCKGEN
Figure 15
Generation Mechanisms for the System Clock
Note: The example for PLL operation shown in Figure 15 refers to a PLL factor of 1:4,
the example for prescaler operation refers to a divider factor of 2:1.
Data Sheet
81
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
The specification of the external timing (AC Characteristics) depends on the period of the
system clock (TCS).
Direct Drive
When direct drive operation is configured (SYSCON0.CLKSEL = 11B), the system clock
is derived directly from the input clock signal DIRIN:
fSYS = fIN.
The frequency of fSYS directly follows the frequency of fIN. In this case, the high and low
time of fSYS is defined by the duty cycle of the input clock fIN.
A similar configuration can be achieved by selecting the XTAL11) input.
Prescaler Operation
When prescaler operation is configured (SYSCON0.CLKSEL = 10B, PLLCON0.VCOBY
= 1B), the system clock is derived either from the crystal oscillator (input clock signal
XTAL1) or from the internal oscillator through the output-prescaler:
fSYS = fOSC / (K1DIV + 1).
If the divider factor is selected as 1, the frequency of fSYS directly follows the frequency
of fOSC. In this case, the high and low time of fSYS is defined by the duty cycle of the input
clock fOSC (external or internal).
The lowest system clock frequency can be achieved in this mode by selecting the
maximum value for divider factor K1:
fSYS = fOSC / 1024.
Phase Locked Loop (PLL)
When PLL operation is configured (SYSCON0.CLKSEL = 10B, PLLCON0.VCOBY = 0B),
the on-chip phase locked loop provides the system clock. The PLL multiplies the
selected input frequency by the factor F (fSYS = fIN × F), which results from the input
divider (P), the multiplication factor (N), and the output divider (K2): (F = N+1 / (P+1 ×
K2+1)).
The input clock can be derived either from an external source via XTAL1 or from the onchip oscillator.
The PLL circuit synchronizes the system clock to the input clock. This synchronization is
done smoothly, i.e. the system clock frequency does not change abruptly.
Due to this adaptation to the input clock the frequency of fSYS is constantly adjusted so it
is locked to fIN. The slight variation causes a jitter of fSYS which also affects the duration
of individual TCSs.
1) Voltages on XTAL1 must comply to the core supply voltage VDDI1.
Data Sheet
82
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
The timing listed in the AC Characteristics refers to TCSs. Therefore, the timing must be
calculated using the minimum TCS possible under the respective circumstances.
The actual minimum value for TCS depends on the jitter of the PLL. As the PLL is
constantly adjusting its output frequency so it corresponds to the applied input frequency
(crystal or oscillator), the accumulated jitter is limited, which means that the relative
deviation for periods of more than one TCS is lower than for one single TCS.
This is especially important for bus cycles using waitstates and e.g. for the operation of
timers, serial interfaces, etc. For all slower operations and longer periods (e.g. pulse train
generation or measurement, lower baudrates, etc.) the deviation caused by the PLL jitter
is, therefore, negligible.
The value of the accumulated PLL jitter depends on the number of consecutive VCO
output cycles within the respective timeframe. The VCO output clock is divided by the
output prescaler (K2+1) to generate the system clock signal fSYS. Therefore, the number
of VCO cycles can be represented as (K2+1) × T, where T is the number of consecutive
fSYS cycles (TCS).
Different frequency bands can be selected for the VCO, so the operation of the PLL can
be adjusted to a wide range of input and output frequencies:
Table 17
VCO Bands for PLL Operation1)
PLLCON0.VCOSEL VCO Frequency Range
Base Frequency Range
00
40 … 120 MHz
10 … 40 MHz
01
90 … 160 MHz
20 … 80 MHz
1X
Reserved
1) Not subject to production test - verified by design/characterization.
Wakeup Oscillator
When wakeup oscillator operation is configured (SYSCON0.CLKSEL = 00B), the system
clock is derived from the low-frequency wakeup oscillator:
fSYS = fWU.
In this mode, a basic functionality can be maintained without requiring an external clock
source and while minimizing the power consumption.
Data Sheet
83
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
Selecting and Changing the Operating Frequency
When selecting a clock source and the clock generation method, the required
parameters must be carefully written to the respective bitfields, to avoid unintended
intermediate states.
Many applications change the frequency of the system clock (fSYS) during the operation,
to optimize performance and power consumption of the system. Changing the operating
frequency also changes the consumed switching current, which influences the power
supply. Therefore, while the core voltage is generated by the on-chip EVRs, the
operating frequency may only be changed by factors of 5 maximum, or in steps of
20 MHz maximum, whatever condition is tighter.
To avoid the indicated problems, recommended sequences are provided which ensure
the intended operation of the clock system interacting with the power system.
4.4.2
On-chip Flash Operation
Accesses to the XC226x’s Flash modules are controlled by the IMB.
Built-in prefetching mechanisms optimize the performance for sequential accesses.
Table 18
Flash Characteristics (Operating Conditions apply)
Parameter
Symbol
Limit Values
Min.
Programming time per 128-byte page
Erase time per sector/page
tPR
tER
Unit
Typ.
Max.
CC –
31)
tbd
ms
CC –
41)
tbd
ms
1) Programming and erase times depend on the internal Flash clock source. The control state machine needs a
few system clock cycles, which only becomes relevant for extremely low system frequencies.
Data Sheet
84
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
4.4.3
Electrical Parameters
External Clock Drive
These parameters define the external clock supply for the XC226x. The clock signal can
be supplied either to pin P2.9 or to pin XTAL1.
Table 19
External Clock Drive Characteristics (Operating Conditions apply)
Parameter
Symbol
tOSC
t1
t2
t3
t4
Oscillator period
High time2)
Low time2)
2)
Rise time
2)
Fall time
Limit Values
Unit
Min.
Max.
SR
25
2501)
ns
SR
6
–
ns
SR
6
–
ns
SR
–
8
ns
SR
–
8
ns
1) The maximum limit is only relevant for PLL operation to ensure the minimum input frequency for the PLL.
2) The clock input signal must reach the defined levels VILC and VIHC (for XTAL1) or VIL and VIH for P2.9.
t3
t1
t4
V IHC
V ILC
0.5 V DDI
t2
t OSC
MCT05572
Figure 16
External Clock Drive XTAL1
Note: If the on-chip oscillator is used together with a crystal or a ceramic resonator, the
oscillator frequency is limited to a range of 4 MHz to 16 MHz.
It is strongly recommended to measure the oscillation allowance (negative
resistance) in the final target system (layout) to determine the optimum
parameters for the oscillator operation. Please refer to the limits specified by the
crystal supplier.
When driven by an external clock signal it will accept the specified input frequency
range. Operation at input frequencies below 4 MHz is possible but is verified by
design only (not subject to production test).
Data Sheet
85
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
4.4.4
Electrical Parameters
Testing Waveforms
These references are used for characterization and production testing (except for pin
XTAL1).
Output delay
Output delay
Hold time
Hold time
0.8 V DDP
0.7 V DDP
Input Signal
(driven by tester)
0.3 V DDP
0.2 V DDP
Output Signal
(measured)
Output timings refer to the rising edge of CLKOUT.
Input timings are calculated from the time, when the input signal reaches
V IH or V IL, respectively.
MCD05556C
Figure 17
Input Output Waveforms
VLoad + 0.1 V
V OH - 0.1 V
Timing
Reference
Points
V Load - 0.1 V
V OL + 0.1 V
For timing purposes a port pin is no longer floating when a 100 mV
change from load voltage occurs, but begins to float when a 100 mV
change from the loaded V OH /V OL level occurs (IOH / IOL = 20 mA).
MCA05565
Figure 18
Data Sheet
Float Waveforms
86
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
4.4.5
Electrical Parameters
External Bus Timing
The following parameters define the behavior of the XC226x’s bus interface.
Table 20
CLKOUT Reference Signal
Parameter
Symbol
Limits
Min.
tc5
tc6
tc7
tc8
tc9
CLKOUT cycle time
CLKOUT high time
CLKOUT low time
CLKOUT rise time
CLKOUT fall time
Unit
Max.
40/25/151)
CC
ns
CC
3
–
ns
CC
3
–
ns
CC
–
3
ns
CC
–
3
ns
1) The CLKOUT cycle time is influenced by the PLL jitter (given values apply to fCPU = 25/40/66 MHz).
For longer periods the relative deviation decreases (see PLL deviation formula).
t C9
t C5
tC6
t C7
tC8
CLKOUT
MCT05571
Figure 19
CLKOUT Signal Timing
Note: The term CLKOUT refers to the reference clock output signal which is generated
by selecting fSYS as source signal for the clock output signal EXTCLK on pin P2.8
and by enabling the high-speed clock driver on this pin.
Data Sheet
87
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
Variable Memory Cycles
External bus cycles of the XC226x are executed in five subsequent cycle phases (AB,
C, D, E, F). The duration of each cycle phase is programmable (via the TCONCSx
registers) to adapt the external bus cycles to the respective external module (memory,
peripheral, etc.).
The duration of the access phase can optionally be controlled by the external module via
the READY handshake input.
This table provides a summary of the phases and the respective choices for their
duration.
Table 21
Programmable Bus Cycle Phases (see timing diagrams)
Bus Cycle Phase
Parameter
Valid Values Unit
Address setup phase, the standard duration of this tpAB
phase (1 … 2 TCS) can be extended by 0 … 3 TCS
if the address window is changed
1 … 2 (5)
TCS
Command delay phase
tpC
0…3
TCS
Write Data setup/MUX Tristate phase
tpD
0…1
TCS
Access phase
tpE
1 … 32
TCS
Address/Write Data hold phase
tpF
0…3
TCS
Note: The bandwidth of a parameter (minimum and maximum value) covers the whole
operating range (temperature, voltage) as well as process variations. Within a
given device, however, this bandwidth is smaller than the specified range. This is
also due to interdependencies between certain parameters. Some of these
interdependencies are described in additional notes (see standard timing).
Timing values are listed in Table 22 and Table 23. The shaded parameters have been
verified by characterization. They are not subject to production test.
Data Sheet
88
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 22
Electrical Parameters
External Bus Cycle Timing for 4.5 V ≤ VDDP ≤ 5.5 V
(Operating Conditions apply)
Parameter
Symbol
Limits
Min.
Typ.
Unit
Max.
Output valid delay for:
RD, WR(L/H)
tc10 CC –
13
ns
Output valid delay for:
BHE, ALE
tc11 CC –
13
ns
Output valid delay for:
A23 … A16, A15 … A0 (on P0/P1)
tc12 CC –
14
ns
Output valid delay for:
A15 … A0 (on P2/P10)
tc13 CC –
14
ns
Output valid delay for:
CS
tc14 CC –
13
ns
Output valid delay for:
D15 … D0 (write data, MUX-mode)
tc15 CC –
14
ns
Output valid delay for:
D15 … D0 (write data, DEMUXmode)
tc16 CC –
14
ns
Output hold time for:
RD, WR(L/H)
tc20 CC 0
8
ns
Output hold time for:
BHE, ALE
tc21 CC 0
8
ns
0
8
ns
Output hold time for:
CS
tc24 CC 0
8
ns
Output hold time for:
D15 … D0 (write data)
tc25 CC 0
8
ns
Input setup time for:
READY, D15 … D0 (read data)
tc30 SR
18
–
ns
Input hold time for:
READY, D15 … D0 (read data)1)
tc31 SR
-4
–
ns
Output hold time for:
tc23 CC
A23 … A16, A15 … A0 (on P2/P10)
Note
1) Read data are latched with the same (internal) clock edge that triggers the address change and the rising edge
of RD. Therefore address changes before the end of RD have no impact on (demultiplexed) read cycles. Read
data can be removed after the rising edge of RD.
Data Sheet
89
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Table 23
Electrical Parameters
External Bus Cycle Timing for 3.0 V ≤ VDDP ≤ 4.5 V
(Operating Conditions apply)
Parameter
Symbol
Limits
Min.
Typ.
Unit
Max.
Output valid delay for:
RD, WR(L/H)
tc10 CC –
20
ns
Output valid delay for:
BHE, ALE
tc11 CC –
20
ns
Output valid delay for:
A23 … A16, A15 … A0 (on P0/P1)
tc12 CC –
22
ns
Output valid delay for:
A15 … A0 (on P2/P10)
tc13 CC –
22
ns
Output valid delay for:
CS
tc14 CC –
20
ns
Output valid delay for:
D15 … D0 (write data, MUX-mode)
tc15 CC –
21
ns
Output valid delay for:
D15 … D0 (write data, DEMUXmode)
tc16 CC –
21
ns
Output hold time for:
RD, WR(L/H)
tc20 CC 0
10
ns
Output hold time for:
BHE, ALE
tc21 CC 0
10
ns
0
10
ns
Output hold time for:
CS
tc24 CC 0
10
ns
Output hold time for:
D15 … D0 (write data)
tc25 CC 0
10
ns
Input setup time for:
READY, D15 … D0 (read data)
tc30 SR
29
–
ns
Input hold time for:
READY, D15 … D0 (read data)1)
tc31 SR
-6
–
ns
Output hold time for:
tc23 CC
A23 … A16, A15 … A0 (on P2/P10)
Note
1) Read data are latched with the same (internal) clock edge that triggers the address change and the rising edge
of RD. Therefore address changes before the end of RD have no impact on (demultiplexed) read cycles. Read
data can be removed after the rising edge of RD.
Data Sheet
90
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
tp AB
tpC
tp D
tp E
tp F
CLKOUT
tc 21
tc 11
ALE
tc 11/tc 14
A23-A16,
BHE, CSx
High Address
tc 20
tc 10
RD
WR(L/H)
tc 31
tc 13
AD15-AD0
(read)
tc 23
Low Address
Data In
tc 13
AD15-AD0
(write)
tc 30
tc 15
Low Address
tc 25
Data Out
MCT05557
Figure 20
Data Sheet
Multiplexed Bus Cycle
91
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
tp AB
tp C
tp D
tp E
tp F
CLKOUT
tc 21
tc 11
ALE
tc 11 /tc 14
A23-A0,
BHE, CSx
Address
tc 20
tc 10
RD
WR(L/H)
tc 31
tc 30
D15-D0
(read)
Data In
tc 16
D15-D0
(write)
tc 25
Data Out
MCT05558
Figure 21
Data Sheet
Demultiplexed Bus Cycle
92
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
Bus Cycle Control via READY Input
The duration of an external bus cycle can be controlled by the external circuitry via the
READY input signal. The polarity of this input signal can be selected.
Synchronous READY permits the shortest possible bus cycle but requires the input
signal to be synchronous to the reference signal CLKOUT.
Asynchronous READY puts no timing constraints on the input signal but incurs one
waitstate minimum due to the additional synchronization stage. The minimum duration
of an asynchronous READY signal to be safely synchronized must be one CLKOUT
period plus the input setup time.
An active READY signal can be deactivated in response to the trailing (rising) edge of
the corresponding command (RD or WR).
If the next following bus cycle is READY-controlled, an active READY signal must be
disabled before the first valid sample point for the next bus cycle. This sample point
depends on the programmed phases of the next following cycle.
Data Sheet
93
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Electrical Parameters
tpD
tp E
tpRDY
tpF
CLKOUT
tc 10
tc 20
RD, WR
tc 31
tc 30
D15-D0
(read)
Data In
tc 25
D15-D0
(write)
Data Out
READY
Synchronous
READY
Asynchron.
tc31
tc 30
tc 30
Not Rdy
READY
tc 31
tc 30
tc 30
Not Rdy
READY
tc 31
tc 31
MCT05559
Figure 22
READY Timing
Note: If the READY input is sampled inactive at the indicated sampling point (“Not Rdy”)
a READY-controlled waitstate is inserted (tpRDY),
sampling the READY input active at the indicated sampling point (“Ready”)
terminates the currently running bus cycle.
Note the different sampling points for synchronous and asynchronous READY.
This example uses one mandatory waitstate (see tpE) before the READY input is
evaluated.
Data Sheet
94
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
5
Package and Reliability
Package and Reliability
In addition to the electrical parameters, the following information ensures proper
integration of the XC226x into the target system.
5.1
Packaging
These parameters describe the housing rather than the silicon.
Table 24
Package Parameters (PG-LQFP-100)
Parameter
Symbol
Limit Values
Min.
Max.
Unit
Notes
Exposed Pad Dimension
Ex × Ey
–
6.2 × 6.2
mm
–
Power Dissipation
PDISS
RΘJA
–
1.0
W
–
–
49
K/W
No thermal via1)
37
K/W
4-layer, no pad2)
22
K/W
4-layer, pad3)
Thermal resistance
Junction-Ambient
1) Device mounted on a 2-layer or 4-layer board without thermal vias.
2) Device mounted on a 4-layer board with thermal vias, exposed pad not soldered.
3) Device mounted on a 4-layer board with thermal vias, exposed pad soldered to the board.
Data Sheet
95
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
Package and Reliability
Package Outlines
Figure 23
PG-LQFP-100 (Plastic Green Thin Quad Flat Package)
You can find all of our packages, sorts of packing and others in our Infineon Internet
Page “Packages”: http://www.infineon.com/packages
Dimensions in mm.
Data Sheet
96
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
5.2
Package and Reliability
Thermal Considerations
When operating the XC226x in a system, the total heat generated on the chip must be
dissipated to the ambient environment to prevent overheating and resulting thermal
damages.
The maximum heat that can be dissipated depends on the package and its integration
into the target board. The “Thermal resistance RΘJA” is a measure for these parameters.
The power dissipation must be limited so the average junction temperature does not
exceed 150 °C.
The difference between junction temperature and ambient temperature is determined by
∆T = (PINT + PIOSTAT + PIODYN) × RΘJA
The internal power consumption is defined as
PINT = VDDP × IDDP (see Table 14).
The static external power consumption caused by the output drivers is defined as
PIOSTAT = Σ((VDDP-VOH) × IOH) + Σ(VOL × IOL)
The dynamic external power consumption caused by the output drivers (PIODYN) depends
on the capacitive load connected to the respective pins and the switching frequencies.
If the total power dissipation determined for a given system configuration exceeds the
defined limit countermeasures must be taken to ensure proper system operation:
•
•
•
•
Reduce VDDP, if possible in the system
Reduce the system frequency
Reduce the number of output pins
Reduce the load on active output drivers
Data Sheet
97
V0.1, 2007-02
Draft Version
XC2267 / XC2264
XC2000 Family Derivatives
Preliminary
5.3
Package and Reliability
Flash Memory Parameters
The data retention time of the XC226x’s Flash memory (i.e. the time after which stored
data can still be retrieved) depends on the number of times the Flash memory has been
erased and programmed.
Table 25
Flash Parameters (XC226x, 768 Kbytes)
Parameter
Data retention time
Symbol
tRET
Flash Erase Endurance NER
Data Sheet
Limit Values
Unit
Notes
Min.
Max.
20
–
years
103 erase/program
cycles
15 × 103
–
cycles
Data retention time
5 years
98
V0.1, 2007-02
Draft Version
w w w . i n f i n e o n . c o m
Published by Infineon Technologies AG