05074 SMDA03LC - SMDA24LCC Only One Name Means ProTek’Tion™ 500 WATT MULTI-LINE LOW CAPACITANCE TVS ARRAY Description The SMDAxxLC and SMDAxxLCC Series are low capacitance multi-line transient voltage suppressor arrays that provides board level protection for standard TTL and MOS bus line applications against the damaging effects of ESD, tertiary lightning and switching transients. The SMDAxxLC/LCC Series has a peak pulse power rating of 500 Watts for an 8/20µs waveshape. This device series meets the IEC 61000-4-2, IEC 61000-4-4 and IEC 61000-4-5 requirements. SO-8 package Features applications • Compatible with IEC 61000-4-2 (ESD): Air - 15kV, Contact - 8kV • Compatible with IEC 61000-4-4 (EFT): 40A - 5/50ns • Compatible with IEC 61000-4-5 (Surge): 12A, 8/20µs - Level 1(LineGnd) & Level 2(Line-Line) • 500 Watts Peak Pulse Power per Line (tp = 8/20µs) • Unidirectional and Bidirectional Configurations • Available in Multiple Voltages Ranging from 3V to 24V • Protects up to Four Lines • Low Capacitance: 15pF • RoHS Compliant • REACH Compliant • Computer Interface Protection • Ethernet - 10/100/1000 Base T • Test and Measurement Equipment • Industrial Control - Low Voltage Sensors Mechanical characteristics • Molded JEDEC SO-8 Package • Approximate Weight: 70 milligrams • Lead-Free Pure-Tin Plating (Annealed) • Solder Reflow Temperature: Pure-Tin - Sn, 100: 260-270°C • 12mm Tape and Reel Per EIA Standard 481 • Flammability Rating UL 94V-0 PIN CONFIGURATIONS 8 7 6 5 8 7 6 5 1 2 3 4 1 2 3 4 UNIDIRECTIONAL 05074.R10 10/12 BIDIRECTIONAL Page 1 www.protekdevices.com 05074 SMDA03LC - SMDA24LCC Only One Name Means ProTek’Tion™ typical device characteristics MAXIMUM RATINGS @ 25°C Unless Otherwise Specified PARAMETER SYMBOL VALUE UNITS TL -55 to 150 °C Storage Temperature TSTG -55 to 150 °C Peak Pulse Power (tp = 8/20µs) - See Figure 1 PPP 500 Watts Forward Voltage @ 50mA, 300µs - Square Wave (See Note 1) VF 1.5 Volts Operating Temperature Note 1. Only applies to unidirectional devices. ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified PART NUMBER (Note 1) DEVICE MARKING RATED STAND-OFF VOLTAGE minimum breakdown voltage MAXIMUM CLAMPING VOLTAGE (Fig. 2) MAXIMUM CLAMPING VOLTAGE (Fig. 2) MAXIMUM LEAKAGE CURRENT MAXIMUM CAPACITANCE VWM VOLTS @1mA V(BR) VOLTS @I P = 1A VC VOLTS @ 8/20µs VC @ IPP VOLTS @V WM ID µA @0V, 1MHz C pF SMDA03LC SLA 3.3 4.5 7.0 10.9V @ 43.0A 125 15 SMDA03LCC SLB 3.3 4.5 7.0 10.9V @ 43.0A 125 15 SMDA05LC SLC 5.0 6.0 9.8 13.5V @ 42.0A 20 15 SMDA05LCC SLD 5.0 6.0 9.8 13.5V @ 42.0A 20 15 SMDA08LC SLE 8.0 8.5 13.4 16.9V @ 34.0A 10 15 SMDA08LCC SLF 8.0 8.5 13.4 16.9V @ 34.0A 10 15 SMDA12LC SLG 12.0 13.3 19.0 25.9V @ 27.0A 1 15 SMDA12LCC SLH 12.0 13.3 19.0 25.9V @ 27.0A 1 15 SMDA15LC SLJ 15.0 16.7 24.0 30.0V @ 17.0A 1 15 SMDA15LCC SLK 15.0 16.7 24.0 30.0V @ 17.0A 1 15 SMDA24LC SLL 24.0 26.7 43.0 49.0V @ 12.0A 1 15 SMDA24LCC SLM 24.0 26.7 43.0 49.0V @ 12.0A 1 15 Notes 1. Part numbers with a “C” suffix are bidirectional devices, i.e., SMDA03LCC. 05074.R10 10/12 Page 2 www.protekdevices.com 05074 SMDA03LC - SMDA24LCC Only One Name Means ProTek’Tion™ typical device characteristics figure 1 peak pulse power vs pulse time PPP - Peak Pulse Power - Watts 10,000 1,000 500W, 8/20µs Waveform 100 10 0.1 10 100 td - Pulse Duration - µs Peak Value IPP 80 100 TEST WAVEFORM PARAMETERS tf = 8µs td = 20µs e-t 60 40 10,000 figure 3 power derating curve Peak Pulse Power 8/20µs 80 % Of Rated Power tf 100 td = t/(IPP/2) 60 40 20 20 0 1,000 figure 2 pulse wave form 120 IPP - Peak Pulse Current - % of IPP 1 0 05074.R10 10/12 5 10 15 t - Time - µs 20 25 30 Page 3 0 Average Power 0 25 50 75 100 125 TA - Ambient Temperature - °C 150 www.protekdevices.com 05074 SMDA03LC - SMDA24LCC Only One Name Means ProTek’Tion™ typical device characteristics figure 4 overshoot & clamping voltage for SMDA05LC 20 5 Volts per Division 10 0 -10 -20 ESD Test Pulse - 5 kilovolt, 1/30ns (Waveshape) 05074.R10 10/12 Page 4 www.protekdevices.com 05074 SMDA03LC - SMDA24LCC Only One Name Means ProTek’Tion™ SPICE MODEL figure 1 spice model I/O I/O LCRD ABD LCRD ABD LCRD ABD LCRD Lg 0.8nH Lg 0.8nH UNIDIRECTIONAL BIDIRECTIONAL ABD - Avalanche Breakdown Diode (TVS) LCRD: Low Capacitance Rectifier Diode Lg - Lead Inductance table 1 - spice parameters parameter PART NUMBER 05074.R10 10/12 unit abd(tvs) LCRD BV V See Table 2 200 IBV µA 1 0.01 Cjo pF See Table 2 5 IS A See Table 2 1E-13 Vj V 0.6 0.6 M - 0.33 0.33 N - 1 1 RS Ohms See Table 2 0.31 TT s 1E-8 1E-9 EG eV 1.11 1.11 table 2 - abd specific spice parameters i s (amps) bv(volts) cjo(pF) rs(ohms) SMDA03LC 4.5 438 1E-11 0.21 SMDA05LC 6.0 284 1E-11 0.14 SMDA08LC 8.5 146 1E-11 0.28 SMDA12LC 13.3 123 1E-13 0.40 SMDA15LC 16.7 102 1E-13 0.52 SMDA24LC 26.7 61 1E-13 1.54 SMDA03LCC 4.5 438 1E-11 0.21 SMDA05LCC 6.0 284 1E-11 0.14 SMDA08LCC 8.5 146 1E-11 0.28 SMDA12LCC 13.3 123 1E-13 0.40 SMDA15LCC 16.7 102 1E-13 0.52 SMDA24LCC 26.7 61 1E-13 1.54 Page 5 www.protekdevices.com 05074 SMDA03LC - SMDA24LCC Only One Name Means ProTek’Tion™ application information Line 1 Line 2 Line 3 Line 4 8 7 6 5 1 2 3 4 GND figure 1 - UNIDIRECTIONAL COMMON-MODE PROTECTION Circuit connectivity is as follows: • Line 1 connected to Pin 5. • Line 2 connected to Pin 6. • Line 3 connected to Pin 7. • Line 4 connected to Pin 8. • Pins 1 - 4 connected to ground. 05074.R10 10/12 Page 6 www.protekdevices.com 05074 SMDA03LC - SMDA24LCC Only One Name Means ProTek’Tion™ application information TPIN TPIP 7 6 5 1 2 3 4 ETHERNET REPEATER 8 TPON TPOP figure 2 - BIDIRECTIONAL COMMON-MODE ETHERNET PROTECTION Circuit connectivity is as follow: • TPIN connected to Pin 5. • TPIP connected to Pin 6. • TPON connected to Pin 1. • TPOP connected to Pin 2. • Pins 3, 4, 7 and 8 connected to ground. circuit board recommendations Circuit board layout is critical for electromagnetic compatibility protection. The following guidelines are recommended: • The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. • The path length between the TVS device and the protected line should be minimized. • All conductive loops including power and ground loops should be minimized. • The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. • Ground planes should be used whenever possible. For multilayer PCBs, use ground vias. 05074.R10 10/12 Page 7 www.protekdevices.com 05074 SMDA03LC - SMDA24LCC Only One Name Means ProTek’Tion™ SO-8 package information outline dimensions dim millimeters -A- inches min max min max A 4.80 5.00 0.189 0.196 B 3.80 4.00 0.150 0.157 C 1.35 1.75 0.054 0.068 D 0.35 0.49 0.014 0.019 F 0.40 1.25 0.016 0.049 G 1.27 BSC 8 5 -B- 1 G 4 D 0.18 0.25 0.007 0.009 K 0.10 0.25 0.004 0.008 P 5.80 6.20 0.229 0.244 R 0.25 0.50 0.010 0.019 R x 45° C 0.05 BSC J + 0.010” (0.25mm) M B M 4 PL P 0° - 10° -T- K + 0.010” (0.25mm) M T B S A S 8 PL J F NOTES 1. 2. 3. 4. 5. 6. -T- = Seating plane and datum surface. Dimensions “A” and “B” are datum. Dimensions “A” and “B” do not include mold protrusion. Maximum mold protrusion is 0.015” (0.380mm) per side. Dimensioning and tolerances per ANSI Y14.5M, 1982. Dimensions are exclusive of mold flash and metal burrs. A pad layout dimensions dim millimeters B inches min max min max A 1.14 1.40 0.045 0.055 B 0.64 0.89 0.025 0.035 C 6.22 - 0.245 - D 3.94 4.17 0.155 0.165 E 1.02 1.27 0.040 0.050 NOTES 1. Controlling dimension: inches. 05074.R10 10/12 D C E Page 8 www.protekdevices.com 05074 SMDA03LC - SMDA24LCC Only One Name Means ProTek’Tion™ TAPE AND REEL P0 D t 10 Pitches Cumulative Tolerance on tape ± 0.2 P2 E F W K0 B0 A0 P User Direction of Feed specifications Reel Dia. Tape Width 178mm (7”) 12mm A0 B0 K0 D E F W P0 P2 P tmax 6.50 ± 0.10 5.40 ± 0.10 2.00 ± 0.10 1.50 ± 0.10 1.75 ± 0.10 5.50 ± 0.05 12.00 ± 0.30 4.00 ± 0.12 2.00 ± 0.10 4.00 ± 0.10 0.25 Notes 1. 2. 3. 4. 5. 6. Dimensions are in millimeters. Surface mount product is taped and reeled in accordance with EIA-481. Suffix - T7 = 7” Reel - 1,000 pieces per 12mm tape. Suffix - T13 = 13” Reel - 2,500 pieces per 12mm tape. Bulk product shipped in tubes of 98 pieces per tube. Marking on Part - marking code (see page 2), date code, logo and pin one defined by dot on top of package. Package outline, pad layout and tape specifications per document number 06009.R3 9/10. ORDERING INFORMATION base PART NUMBER (xx = Voltage) LEADFREE SUFFIX TAPE SUFFIX QTY/REEL REEL SIZE TUBE qty SMDAxx/SMDAxxC -LF -T7 1,000 7” 98 SMDAxx/SMDAxxC -LF -T13 2,500 13” 98 This device is only available in a Lead-Free configuration. 05074.R10 10/12 Page 9 www.protekdevices.com 05074 SMDA03LC - SMDA24LCC Only One Name Means ProTek’Tion™ company information COMPANY PROFILE In business more than 20 years, ProTek Devices™ is a privately-held company located in Tempe, Arizona, that offers a product line of transient voltage suppressors (TVS); avalanche breakdown diodes; steering diode TVS arrays and other surge suppressor component products. These TVS devices protect electronic systems from the effects of lightning, electrostatic discharge (ESD), nuclear electromagnetic pulses (NEMP), inductive switching and EMI / RFI. ProTek Devices also offers high performance interface and linear products that include analog switches; multiplexers; LED drivers; audio control ICs; RF and related high frequency products. The analog devices work in a host of consumer; industrial; automotive and other applications. CONTACT US Corporate Headquarters 2929 South Fair Lane Tempe, Arizona 85282 USA By Telephone General: 602-431-8101 Sales: & Marketing: 602-414-5109 Customer Service: 602-414-5114 Product Technical Support: 602-414-5107 By Fax General: 602-431-2288 By E-mail: Sales: [email protected] Customer Service: [email protected] Technical Support: [email protected] ProTek Devices (Asia Pacific) Pte. Ltd. 8 Ubi Road 2, #06-19 Zervex Singapore - 408538 Tel: +65-67488312 Fax: +65-67488313 Web www.protekdevices.com COPYRIGHT © ProTek Devices 2000 - This literature is subject to all applicable copyright laws and is not for resale in any manner. SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice. DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance. ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ProTek assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability without limitation special, consequential or incidental damages. LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without written consent from the factory. 05074.R10 10/12 Page 10 www.protekdevices.com