SN74CBTLV1G125 LOW-VOLTAGE SINGLE FET BUS SWITCH www.ti.com SCDS057H – MARCH 1998 – REVISED JUNE 2006 FEATURES • • • 5-Ω Switch Connection Between Two Ports Rail-to-Rail Switching on Data I/O Ports Ioff Supports Partial-Power-Down Mode Operation DBV PACKAGE (TOP VIEW) OE 1 A 2 GND 3 DCK PACKAGE (TOP VIEW) OE 1 A 2 GND 3 VCC 5 5 VCC 4 B B 4 See mechanical drawings for dimensions. DESCRIPTION/ORDERING INFORMATION The SN74CBTLV1G125 features a single high-speed line switch. The switch is disabled when the output-enable (OE) input is high. This device is fully specified for partial-power-down applications using Ioff. The Ioff feature ensures that damaging current will not backflow through the device when it is powered down. The device has isolation during power off. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION TA –40°C to 85°C (1) (2) PACKAGE (1) TOP-SIDE MARKING (2) ORDERABLE PART NUMBER SOT (SOT-23) – DBV Reel of 3000 SN74CBTLV1G125DBVR V25_ SOT (SC-70) – DCK Reel of 3000 SN74CBTLV1G125DCKR VM_ Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. The actual top-side marking has one additional character that designates the assembly/test site. FUNCTION TABLE INPUT OE FUNCTION L A port = B port H Disconnect LOGIC DIAGRAM (POSITIVE LOGIC) 2 A OE 4 SW B 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1998–2006, Texas Instruments Incorporated SN74CBTLV1G125 LOW-VOLTAGE SINGLE FET BUS SWITCH www.ti.com SCDS057H – MARCH 1998 – REVISED JUNE 2006 SIMPLIFIED SCHEMATIC, EACH FET SWITCH A B (OE) Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range –0.5 4.6 V VI Input voltage range (2) –0.5 4.6 V 128 V VI/O < 0 –50 mA DBV package 206 DCK package 252 Continuous channel current IIK Input clamp current θJA Package thermal impedance (3) Tstg Storage temperature range (1) (2) (3) –65 150 UNIT °C/W °C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions (1) VCC VIH High-level control input voltage VIL Low-level control input voltage TA Operating free-air temperature (1) 2 Supply voltage MIN MAX 2.3 3.6 VCC = 2.3 V to 2.7 V 1.7 VCC = 2.7 V to 3.6 V 2 V V VCC = 2.3 V to 2.7 V 0.7 VCC = 2.7 V to 3.6 V 0.8 –40 UNIT 85 V °C All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. Submit Documentation Feedback SN74CBTLV1G125 LOW-VOLTAGE SINGLE FET BUS SWITCH www.ti.com SCDS057H – MARCH 1998 – REVISED JUNE 2006 Electrical Characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER MIN TYP (1) MAX TEST CONDITIONS VIK VCC = 3 V, II = –18 mA II UNIT –1.2 V VCC = 3.6 V, VI = VCC or GND ±1 µA Ioff VCC = 0, VI or VO = 0 to 3.6 V 10 µA ICC VCC = 3.6 V, IO = 0, VI = VCC or GND 10 µA 300 µA ∆ICC (2) Control inputs VCC = 3.6 V, One input at 3 V, Other inputs at VCC or GND Ci Control inputs VI = 3 V or 0 Cio(OFF) 2.5 VO = 3 V or 0, OE = VCC VCC = 2.3 V, TYP at VCC = 2.5 V ron (3) II = 64 mA VI = 0 VI = 1.7 V, VI = 0 VCC = 3 V VI = 2.4 V, (1) (2) (3) pF 7 pF 7 10 II = 24 mA 7 10 II = 15 mA 15 25 II = 64 mA 5 7 II = 24 mA 5 7 II = 15 mA 10 15 Ω All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C. This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND. Measured by the voltage drop between A and B terminals at the indicated current through the switch. On-state resistance is determined by the lower of the voltages of the two (A or B) terminals. Switching Characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) (1) VCC = 2.5 V ± 0.2 V VCC = 3.3 V ± 0.3 V FROM (INPUT) TO (OUTPUT) tpd (1) A or B B or A ten OE A or B 1 4 tdis OE A or B 1 5 PARAMETER MIN MAX MIN 0.15 UNIT MAX 0.25 ns 1 4 ns 1 4.1 ns The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance of 50 pF, when driven by an ideal voltage source (zero output impedance). Submit Documentation Feedback 3 SN74CBTLV1G125 LOW-VOLTAGE SINGLE FET BUS SWITCH www.ti.com SCDS057H – MARCH 1998 – REVISED JUNE 2006 PARAMETER MEASUREMENT INFORMATION 2 × VCC S1 RL From Output Under Test Open GND CL (see Note A) TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND RL LOAD CIRCUIT VCC CL RL V∆ 2.5 V ±0.2 V 3.3 V ±0.3 V 30 pF 50 pF 500 Ω 500 Ω 0.15 V 0.3 V VCC Timing Input VCC/2 0V tw tsu VCC VCC/2 Input th VCC VCC/2 VCC/2 Data Input VCC/2 0V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION VCC VCC/2 Input 0V tPHL tPLH VOH VCC/2 Output VCC/2 VOL tPHL Output Waveform 1 S1 at 2 × VCC (see Note B) tPLH VOH Output VCC/2 VCC Output Control VCC/2 VCC/2 VOL Output Waveform 2 S1 at GND (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS VCC/2 0V tPZL tPLZ VCC VCC/2 tPZH VOL + V∆ VOH − V∆ VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2 ns, tf ≤ 2 ns. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. All parameters and waveforms are not applicable to all devices. Submit Documentation Feedback VOL tPHZ VCC/2 Figure 1. Load Circuit and Voltage Waveforms 4 VCC/2 VOH ≈0 V PACKAGE OPTION ADDENDUM www.ti.com 12-Mar-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TBD Lead/Ball Finish Call TI MSL Peak Temp (3) 74CBTLV1G125CRE4 ACTIVE SC70 DCK 5 74CBTLV1G125CRG4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Call TI Level-1-260C-UNLIM 74CBTLV1G125DBVRE4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74CBTLV1G125DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74CBTLV1G125DCKRG4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74CBTLV1G125DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74CBTLV1G125DCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN74CBTLV1G125 : • Automotive: SN74CBTLV1G125-Q1 NOTE: Qualified Version Definitions: • Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 22-Feb-2010 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN74CBTLV1G125DBVR SOT-23 DBV 5 3000 180.0 9.2 3.23 3.17 1.37 4.0 8.0 Q3 SN74CBTLV1G125DCKR DCK 5 3000 180.0 9.2 2.24 2.34 1.22 4.0 8.0 Q3 SC70 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 22-Feb-2010 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74CBTLV1G125DBVR SN74CBTLV1G125DCKR SOT-23 DBV 5 3000 205.0 200.0 33.0 SC70 DCK 5 3000 205.0 200.0 33.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated