OPTOWAY SPS

Optoway
SPS-33200WG
1
***********************************************************************************************************************************************************************
SPS-33200WG / SPS-33200BWG (RoHS Compliant)
3.3V / 1550 nm / 155 Mbps Digital Diagnostic LC SFP SINGLE-MODE TRANSCEIVER
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l
l
l
l
l
l
l
l
l
l
l
l
l
The SPS-33200WG series single mode transceiver is small
form factor pluggable module for bi-directional serial
optical data communications such as SONET OC-3 / SDH
STM-1 and Fast Ethernet. It is with the SFP 20-pin
connector to allow hot plug capability. Digital diagnostic
functions are available via an I2C. A guaranteed minimum
optical link budget of 46 dB is offered which can
correspond to a link distance of over 200 km (assuming
worst case fiber loss of 0.2 dB/km). This module is
designed for single mode fiber and operates at a nominal
wavelength of 1550 nm. The transmitter section uses a
1550 nm multiple quantum well DFB laser and is a class 1
laser compliant according to International Safety Standard
IEC-60825. The receiver section uses an integrated InGaAs
detector preamplifier (IDP) mounted in an optical header
and a limiting post-amplifier IC.
Hot-Pluggable SFP Footprint LC Optical Transceiver
Small Form-Factor Pluggable (SFP) MSA compatible
Compliant with SONET OC-3 / SDH STM-1
SFF-8472 Digital Diagnostic Function
1550 nm DFB LD Transmitter
46 dB Power Budget at Least
Distance up to 200 km
AC/AC Coupling according to MSA
Single +3.3 V Power Supply
RoHS Compliant
0 to 70oC Operation: SPS-33200WG
-10 to 85oC Operation: SPS-33200BWG
Class 1 Laser International Safety Standard IEC-60825
Compliant
APPLICATIONS
l ATM Switches and Routers
l SONET / SDH Switch Infrastructure
l Fast Ethernet Applications
LASER SAFETY
This single mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
ORDER INFORMATION
P/No.
Bit Rate
(Mb/s)
SONET
/SDH
Distance
(km)
Wavelength
(nm)
Package
Temp.
(oC)
SPS-33200WG
125 / 155
200
1550 DFB LC SFP with DMI
0 to 70
SPS-33200BWG
125 / 155
200
1550 DFB LC SFP with DMI -10 to 85
TX Power RX Sens.
RoHS
(dBm)
(dBm) Compliant
5 to 1
-45
Yes
5 to 1
-45
Yes
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Case Temperature
Power Supply Voltage
Symbol
Tstg
Topr
Vcc
Min
-40
0
-10
-0.5
Max
85
70
85
3.6
Units
o
C
o
C
Min
3.13
0
-10
Typ
3.3
Max
3.47
70
85
300
200
Notes
SPS-33200WG
SPS-33200BWG
V
Recommended Operating Conditions
Parameter
Power Supply Voltage
Operating Case Temperature
Power Supply Current
Data Rate
Symbol
Vcc
Topr
ICC (TX+RX)
200
125/155
Units / Notes
V
o
C / SPS-33200WG
o
C / SPS-33200BWG
mA
Mb/s
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
3/1/2006 V1.0
Optoway
SPS-33200WG
2
***********************************************************************************************************************************************************************
Transmitter Specifications (0 oC < Topr < 70 oC, 3.13V < Vcc < 3.47V)
Parameter
Symbol
Min
Typ
Max
Units
Optical
Optical Transmit Power
Po
1
--5
dBm
Output Center Wavelength
1480
1580
nm
λ
Output Spectrum Width
----1
nm
∆λ
Side Mode Suppression Ratio
SMSR
30
dB
Extinction Ratio
ER
10
----dB
Output Eye
Compliant with Bellcore TR-NWT-000253 and ITU recommendation G.957
Optical Rise Time
tr
2
ns
Optical Fall Time
tf
2
ns
Relative Intensity Noise
RIN
-120
dB/Hz
Electrical
Data Input Current – Low
IIL
-350
µA
Data Input Current – High
IIH
350
µA
Differential Input Voltage
VIH - V IL
0.5
2.4
V
TX Disable Input Voltage – Low
TDIS, L
0
0.5
V
TX Disable Input Voltage – High
TDIS, H
2.0
Vcc
V
TX Disable Assert Time
T ASSERT
10
µs
TX Disable Deassert Time
TDEASSERT
1
ms
TX Fault Output Voltage -- Low
TFaultL
0
0.8
V
TX Fault Output Voltage -- High
TFaultH
2.0
Vcc+0.3
V
1. Output power is power coupled into a 9/125 µm single mode fiber.
2. There is an internal 4.7K to 10K ohm pull-up resistor to VccTX.
3. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage).
Notes
1
-20 dB Width
10 % to 90% Values
10 % to 90% Values
Peak-to-Peak
2
2
3
3
Receiver Specifications (0oC < Topr < 70oC, 3.13V < Vcc < 3.47V)
Parameter
Symbol
Min
Typ
Max
Units
Notes
Optical
Sensitivity
Sens
-45
dBm
4
Maximum Input Power
Pin
-10
dBm
4
Signal Detect -- Asserted
Pa
---45
dBm
Transition: low to high
Signal Detect -- Deasserted
Pd
-55
----dBm
Transition: high to low
Signal detect -- Hysteresis
1.0
--dB
Wavelength of Operation
1200
--1600
nm
Electrical
Differential Output Voltage
VOH – VOL
0.6
2.0
V
Output LOS Voltage -- Low
VOL
0
0.8
V
5
Output LOS Voltage -- High
VOH
2.0
Vcc+0.3
V
5
23
4. Measured at 2 -1 PRBS at BER 1E-10. Receiver sensitivity is better than -45dBm at 155 Mbps and 125 Mbps. However, due to the
resolution limitation of Digital Diagnostic Monitoring, the effect readout range for the RX received power at EEPROM A2 is from -10
to -34 dBm.
5. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage).
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
3/1/2006 V1.0
Optoway
SPS-33200WG
3
***********************************************************************************************************************************************************************
CONNECTION DIAGRAM
PIN
Signal Name
1
2
3
TX GND
TX Fault
TX Disable
4
MOD-DFE2
5
MOD-DEF1
6
MOD-DEF0
7
8
9
10
N/C
LOS
RX GND
RX GND
Description
PIN
Transmitter Ground
Transmitter Fault Indication
Transmitter Disable (Module disables
on high or open)
Modulation Definition 2 – Two wires
serial ID Interface
Modulation Definition 1 – Two wires
serial ID Interface
Modulation Definition 0 – Ground in
Module
Not Connected
Loss of Signal
Receiver Ground
Receiver Ground
11
12
13
RX GND
Receiver Ground
RX DATA OUT- Inverse Receiver Data Out
RX DATA OUT+ Receiver Data Out
Signal Name
Description
14
RX GND
Receiver Ground
15
Vcc RX
Receiver Power – 3.3V±5%
16
Vcc TX
Transmitter Power – 3.3V±5%
17
18
19
20
TX GND
TX DATA IN+
TX DATA INTX GND
Transmitter Ground
Transmitter Data In
Inverse Transmitter Data In
Transmitter Ground
Module Definition
Module Definition
MOD-DEF2
PIN 4
MOD-DEF1
PIN 5
MOD-DEF0
PIN 6
Interpretation by Host
4
SDA
SCL
LV-TTL Low
Serial module definition
protocol
Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector
(NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the
2-wire serial CMOS E 2PROM protocol of the ATMEL AT24C01A/02/04 family of components.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
3/1/2006 V1.0
Optoway
SPS-33200WG
4
***********************************************************************************************************************************************************************
RECOMMENDED CIRCUIT SCHEMATIC
VeeT
Tx_DISABLE
Tx_FAULT
(1,17,20)
3
Tx_DISABLE
2
Tx_FAULT
4.7K to 10KΩ
LD
Driver
TD +
18
TD -
19
TD +
Z=50Ω
100Ω
TD Z=50Ω
VccT
1μH
16
Vcc 3.3V
10μF
10nF
10μF
10nF
SerDes
IC
1μH
VccR
15
10μF
10nF
RD -
12
Protocol
IC
RD Z=50Ω
100Ω
POST
Amp
RD +
13
RD +
Z=50Ω
4.7K to 10KΩ
LOS
VeeR
MOD_DEF(0)
EEPROM
MOD_DEF(1)
MOD_DEF(2)
SFP module
depending on SERDES
8
LOSS OF SINGAL
(9,10,11,14)
6
MODULE DETECT
5
SCL
4
SDA
4.7K to 10KΩ
4.7K to 10KΩ
Vcc 3.3V
4.7K to 10KΩ
PACKAGE DIAGRAM
Units in mm
Note: Specifications subject to change without notice.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
3/1/2006 V1.0