SY2333 Semiconductor Chip LED Features • • • • Colorless transparency lens type Compact type Radiation size 1.3 ㎜×2.9 ㎜ Surface mount lead configuration Outline Dimensions unit : mm 2.40~2.60 0.50 Max. 1.80~2.00 2.80~3.00 1.20~1.40 0.10 Max. 0.90~1.10 0.50 Max. 0.20 Min. 1 2 PIN Connections 1. Anode 2. N.C. 3. Cathode 1 KSD-O8Q004-001 1 SY2333 Absolute Maximum Ratings (Ta=25oC) Characteristic Symbol Ratings Unit Power dissipation PD 63 mW Forward current IF 25 mA IFP 50 mA Reverse voltage VR 4 V Operating temperature range Topr -25∼80 ℃ Storage temperature range Tstg -30∼100 ℃ 1 * Peak forward current 2 * Soldering temperature Tsol 240℃ for 10 seconds *1. Duty ratio = 1/16, Pulse width = 0.1ms *2. Recommended reflow soldering temperature profile - Preheating 150℃ to 185℃ within 120 seconds soldering 240℃ within 10 seconds Gradual cooling (Avoid quenching) Temp (℃) Peak Temp max. 240℃ 240 Preheating area 150~185℃, 90±30sec max. 10sec Solder area 220℃, max. 60sec 185 150 max. 3℃/sec max. -6℃/sec max. 4℃/sec Time from 25℃ to Peak Temperature max. 6min 25 0 60 150 180 240 Time (sec) Electrical / Optical Characteristics Characteristic (Ta=25oC) Symbol Test Condition Min Typ. Max. Unit Forward voltage VF IF= 20mA - 2.1 2.5 V Luminous intensity IV IF= 20mA 2 - - mcd Peak wavelength λP ∆λ IR IF= 20mA - 585 - nm IF= 20mA - 30 - nm VR=4V - - 10 uA - ±55 - Spectrum bandwidth Reverse current *3Half angle θ1/2 X Y IF= 20mA ±70 deg *3. θ1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity KSD-O8Q004-001 2 SY2333 Fig. 1 IF - VF Fig. 2 IV - IF Forward Current IF [mA] Luminous Intensity Iv [mcd] Characteristic Diagrams Forward Voltage VF [V] Forward Fig. 3 IF – Ta Forward Relative Intensity [%] Current IF [mA] Fig.4 Spectrum Distribution Ambient Temperature Ta [℃] Wavelength λ [nm] Fig. 5-1 Radiation Diagram(X) 100 Current IF [mA] 50 0 Fig. 5-2 Radiation Diagram(Y) 50 100 Relative Luminous Intensity Iv [%] KSD-O8Q004-001 Relative Luminous Intensity Iv [%] Relative Luminous Intensity Iv [%] 3 SY2333 The AUK Corp. products are intended for the use as components in general electronic equipment (Office and communication equipment, measuring equipment, home appliance, etc.). Please make sure that you consult with us before you use these AUK Corp. products in equipments which require high quality and / or reliability, and in equipments which could have major impact to the welfare of human life(atomic energy control, airplane, spaceship, transportation, combustion control, all types of safety device, etc.). AUK Corp. cannot accept liability to any damage which may occur in case these AUK Corp. products were used in the mentioned equipments without prior consultation with AUK Corp.. Specifications mentioned in this publication are subject to change without notice. KSD-O8Q004-001 4