TC74HC4066AP/AF/AFN/AFT TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74HC4066AP,TC74HC4066AF,TC74HC4066AFN,TC74HC4066AFT Quad Bilateral Switch The TC74HC4066A is a high speed CMOS QUAD BILATERAL SWITCH fabricated with silicon gate C2MOS technology. It consists of four independent high speed switches capable of controlling either digital or analog signals while maintaining the CMOS low power dissipation. Control input (C) is provided to control the switch. The switch turns ON while the C input is high, and the switch turns OFF while low. All inputs are equipped with protection circuits against static discharge or transient excess voltage. Note: xxxFN (JEDEC SOP) is not available in Japan. TC74HC4066AP TC74HC4066AF Features • High speed: tpd = 7 ns (typ.) at VCC = 5 V • Low power dissipation: ICC = 1 μA (max) at Ta = 25°C • High noise immunity: VNIH = VNIL = 28% VCC (min) • Low on resistance: RON = 50 Ω (typ.) at VCC = 9 V • High degree of linearity: THD = 0.05% (typ.) at VCC = 5 V • Pin and function compatible with 4066B TC74HC4066AFN TC74HC4066AFT Weight DIP14-P-300-2.54 SOP14-P-300-1.27A SOL14-P-150-1.27 TSSOP14-P-0044-0.65A 1 : 0.96 g (typ.) : 0.18 g (typ.) : 0.12 g (typ.) : 0.06 g (typ.) 2007-10-01 TC74HC4066AP/AF/AFN/AFT Pin Assignment 1I/O IEC Logic Symbol 14 1 1C VCC 1O/I 2 13 1C 2O/I 3 12 4C 2I/O 4 11 4I/O 1I/O 2C 2I/O 3C 2C 5 10 4O/I 3C 6 9 3O/I GND (VSS) 7 8 3I/O 3I/O 4C 4I/O (13) (1) ×1 1 1 (2) 1O/I (5) (4) (3) 2O/I (6) (8) (9) 3O/I (12) (11) (10) 4O/I (top view) Truth Table Control Switch Function H On L Off 2 2007-10-01 TC74HC4066AP/AF/AFN/AFT Absolute Maximum Ratings (Note 1) Characteristics Symbol Rating Unit Supply voltage range VCC −0.5 to 13 V Control input voltage VIN −0.5 to VCC + 0.5 V Switch I/O voltage VI/O −0.5 to VCC + 0.5 V Control input diode current IIK ±20 mA I/O diode current IOK ±20 mA Switch through Current IOUT ±25 mA DC VCC/ground current ICC ±50 mA Power dissipation PD 500 (DIP) (Note 2)/180 (SOP/TSSOP) mW Storage temperature Tstg −65 to 150 °C Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 2: 500 mW in the range of Ta = −40 to 65°C. From Ta = 65 to 85°C a derating factor of −10 mW/°C should be applied up to 300 mW. Operating Ranges (Note) Characteristics Symbol Rating Unit Supply voltage VCC 2 to 12 V Control input voltage VIN 0 to VCC V Switch I/O voltage VI/O 0 to VCC V Operating temperature Topr −40 to 85 °C 0 to 1000 (VCC = 2.0 V) Input rise and fall time 0 to 500 (VCC = 4.5 V) tr, tf 0 to 400 (VCC = 6.0 V) ns 0 to 250 (VCC = 10.0 V) Note: The operating ranges must be maintained to ensure the normal operation of the device. Unused control inputs must be tied to either VCC or GND. 3 2007-10-01 TC74HC4066AP/AF/AFN/AFT Electrical Characteristics DC Characteristics Ta = −40 to 85°C Ta = 25°C Characteristics High-level control input voltage Low-level control input voltage On resistance Symbol Test Condition Min Typ. Max Min Max 2.0 1.50 ― ― 1.50 ― 4.5 3.15 ― ― 3.15 ― 9.0 6.30 ― ― 6.30 ― 12.0 8.40 ― ― 8.40 ― 2.0 ― ― 0.50 ― 0.50 4.5 ― ― 1.35 ― 1.35 9.0 ― ― 2.70 ― 2.70 12.0 ― ― 3.60 ― 3.60 VIN = VIHC 4.5 ― 96 170 ― 200 VI/O = VCC to GND 9.0 ― 55 85 ― 100 II/O ≤ 1 mA 12.0 ― 45 80 ― 90 2.0 ― 160 ― ― ― 4.5 ― 70 100 ― 130 9.0 ― 50 75 ― 95 12.0 ― 45 70 ― 90 VIN = VIHC 4.5 ― 10 ― ― ― VI/O = VCC to GND 9.0 ― 5 ― ― ― II/O ≤ 1 mA 12.0 ― 5 ― ― ― 12.0 ― ― ±100 ― ±1000 nA 12.0 ― ― ±100 ― ±1000 nA 12.0 ― ― ±100 ― ±1000 nA 6.0 ― ― 1.0 ― 10.0 9.0 ― ― 4.0 ― 40.0 12.0 ― ― 8.0 ― 80.0 ― VIHC ― VILC RON VIN = VIHC VI/O = VCC or GND II/O ≤ 1 mA Difference of on resistance between switches Input/output leakage current ΔRON (switch on, output open) V V Ω Ω VOS = VCC or GND IOFF (switch off) Switch input leakage current Unit VCC (V) VIS = GND or VCC VIN = VILC IIZ VOS=VCC or GND VIN = VIHC Control input current IIN VIN = VCC or GND Quiescent supply current ICC VIN = VCC or GND 4 μA 2007-10-01 TC74HC4066AP/AF/AFN/AFT AC Characteristics (CL = 50 pF, input: tr = tf = 6 ns) Characteristics Phase difference between input and output Output enable time Output disable time Symbol φI-O tpZL tpZH tpLZ tpHZ ― RL = 1 kΩ RL = 1 kΩ RL = 1 kΩ Maximum control input frequency Ta = −40 to 85°C Ta = 25°C Test Condition CL = 15 pF VOUT = 1/2 VCC VCC (V) Min Typ. Max Min Max 2.0 ― 10 50 ― 65 4.5 ― 4 10 ― 13 9.0 ― 3 8 ― 10 12.0 ― 3 7 ― 9 2.0 ― 18 100 ― 125 4.5 ― 8 20 ― 25 9.0 ― 6 12 ― 22 12.0 ― 6 12 ― 18 2.0 ― 20 115 ― 145 4.5 ― 10 23 ― 29 9.0 ― 8 20 ― 25 12.0 ― 8 18 ― 22 2.0 ― 30 ― ― ― 4.5 ― 30 ― ― ― 9.0 ― 30 ― ― ― 12.0 ― 30 ― ― ― Unit pF pF pF MHz Control input capacitance CIN ― ― 5 10 ― 10 pF Switch terminal capacitance CI/O ― ― 6 ― ― ― pF Feed through capacitance CIOS ― ― 0.5 ― ― ― pF Power dissipation capacitance CPD ― 15 ― ― ― pF Note: (Note) CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD·VCC·fIN + ICC/4 (per channel) 5 2007-10-01 TC74HC4066AP/AF/AFN/AFT Analog Switch Characteristics (GND = 0 V, Ta = 25°C) (Note) Characteristics Symbol Test Condition VCC (V) Typ. 4.5 0.05 9.0 0.04 Increase fIN frequency until dB meter reads −3dB 4.5 200 RL = 50 Ω, CL = 10 pF 9.0 200 fIN = 1 kHz, VIN = 4 Vp-p, @VCC = 4.5 V Sine wave distortion RL = 10 kΩ, VIN = 8 Vp-p, @VCC = 9.0 V (T.H.D) CL = 50 pF Unit % Adjust fIN voltage to obtain 0dBm at VOS Frequency response (switch on) fmax MHz fIN = 1 MHz, sine wave Vin is centered at VCC/2 Feedthrough attenuation Adjust input for 0dBm 4.5 −60 (switch off) RL = 600 Ω, CL = 50 pF 9.0 −60 dB fIN = 1 MHz, sine wave Crosstalk RL = 600 Ω, CL = 50 pF 4.5 60 (control input to signal output) fIN = 1 MHz, square wave (tr = tf = 6 ns) 9.0 100 4.5 −60 9.0 −60 Adjust VIN to obtain 0dBm at input Crosstalk (between any switches) Note: RL = 600 Ω, CL = 50 pF fIN = 1 MHz, sine wave mV dB These characteristics are determined by design of devices. 6 2007-10-01 TC74HC4066AP/AF/AFN/AFT Switching Characteristics Test Circuits 1. tpLZ, tpHZ, tpZL, tpZH 6 ns VCC 6 ns VCC VC C I/O 1 kΩ O/I S1 VO/I (S1 = VCC, S2 = GND) S2 50% GND GND 50% VO/I (S1 = GND, S2 = VCC) 50% tpZL 90% tpHZ tpZH 50 pF from P.G 10% VCC VOH VOL VOH 10% VOL tpLZ 2. Cross Talk (control input-switch output) fIN = 1 MHz duty = 50% tr = tf = 6 ns VCC from P.G I/O O/I 600 Ω VCC/2 50 pF VCC/2 VCC C 600 Ω VCC GND GND 3. Feedthrough Attenuation VCC I/O O/I GND 50 pF 600 Ω 0.1 μF VCC 600 Ω C 7 2007-10-01 TC74HC4066AP/AF/AFN/AFT 4. CIOS, CI/O CIOS VCC VCC C I/O O/I CI/O CI/O GND 5. Crosstalk (between any two switches) VIN VCC C VCC I/O O/I O/I GND 50 pF I/O 600 Ω 600 Ω C 50 pF 600 Ω 0.1 μF 600 Ω 6. Frequency Response (switch on) I/O O/I GND 10 pF 0.1 μF VCC 50 Ω C 8 2007-10-01 TC74HC4066AP/AF/AFN/AFT Package Dimensions Weight: 0.96 g (typ.) 9 2007-10-01 TC74HC4066AP/AF/AFN/AFT Package Dimensions Weight: 0.18 g (typ.) 10 2007-10-01 TC74HC4066AP/AF/AFN/AFT Package Dimensions (Note) Note: This package is not available in Japan. Weight: 0.12 g (typ.) 11 2007-10-01 TC74HC4066AP/AF/AFN/AFT Package Dimensions Weight: 0.06 g (typ.) 12 2007-10-01 TC74HC4066AP/AF/AFN/AFT RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 13 2007-10-01