TI TLC2201CP

TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
D
D
D
D
B Grade Is 100% Tested for Noise
30 nV/√Hz Max at f = 10 Hz
12 nV/√Hz Max at f = 1 kHz
Low Input Offset Voltage . . . 500 µV Max
Excellent Offset Voltage Stability
With Temperature . . . 0.5 µV/°C Typ
Rail-to-Rail Output Swing
D
D
D
Low Input Bias Current
1 pA Typ at TA = 25°C
Common-Mode Input Voltage Range
Includes the Negative Rail
Fully Specified For Both Single-Supply and
Split-Supply Operation
TYPICAL EQUIVALENT
INPUT NOISE VOLTAGE
vs
FREQUENCY
description
The combination of excellent dc and noise
performance with a common-mode input voltage
range that includes the negative rail makes these
devices an ideal choice for high-impedance,
low-level signal-conditioning applications in either
single-supply or split-supply configurations.
60
V n – Equivalent Input Noise Voltage – nV/ Hz
Hz
Vn
The TLC220x, TLC220xA, TLC220xB, and
TLC220xY are precision, low-noise operational
amplifiers using Texas Instruments Advanced
LinCMOS process. These devices combine the
noise performance of the lowest-noise JFET
amplifiers with the dc precision available
previously only in bipolar amplifiers. The
Advanced LinCMOS process uses silicon-gate
technology to obtain input offset voltage stability
with temperature and time that far exceeds that
obtainable using metal-gate technology. In
addition, this technology makes possible input
impedance levels that meet or exceed levels
offered by top-gate JFET and expensive
dielectric-isolated devices.
VDD = 5 V
RS = 20 Ω
TA = 25°C
50
40
30
20
10
0
1
10
100
1k
10 k
f – Frequency – Hz
The device inputs and outputs are designed to withstand –100-mA surge currents without sustaining latch-up.
In addition, internal ESD-protection circuits prevent functional failures at voltages up to 2000 V as tested under
MIL-PRF-38535, Method 3015.2; however, care should be exercised in handling these devices as exposure
to ESD may result in degradation of the parametric performance.
The C-suffix devices are characterized for operation from 0°C to 70°C. The I-suffix devices are characterized
for operation from – 40 °C to 85°C. The M-suffix devices are characterized for operation over the full military
temperature range of – 55°C to 125°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Advanced LinCMOS is a trademark of Texas Instruments Incorporated.
Copyright  1997, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201 AVAILABLE OPTIONS
TA
VIOmax
AT 25°C
Vnmax
f = 10 Hz
AT 25°C
Vnmax
f = 1 kHz
AT 25°C
0C
0°C
to
70°C
200 µV
200 µV
µ
500 µV
35 nV/√Hz
30 nV/√Hz
—
– 40
40°C
C
to
85°C
200 µV
200 µV
µ
500 µV
– 55°C
to
125°C
200 µV
µ
200 µV
500 µV
PACKAGED DEVICES
CHIP
FORM‡
(Y)
SMALL
OUTLINE†
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(P)
15 nV/√Hz
12 nV/√Hz
—
TLC2201ACD
TLC2201BCD
TLC2201CD
—
—
TLC2201ACP
TLC2201BCP
TLC2201CP
TLC2201Y
35 nV/√Hz
30 nV/√Hz
—
15 nV/√Hz
12 nV/√Hz
—
TLC2201AID
TLC2201BID
TLC2201ID
—
—
TLC2201AIP
TLC2201BIP
TLC2201IP
—
35 nV/√Hz
30 nV/√Hz
—
15 nV/√Hz
12 nV/√Hz
—
TLC2201AMD
TLC2201BMD
TLC2201MD
TLC2201AMJG
TLC2201BMJG
TLC2201MJG
TLC2201AMP
TLC2201BMP
TLC2201MP
—
TLC2201AMFK
TLC2201BMFK
TLC2201MFK
† The D packages are available taped and reeled. Add R suffix to device type (e.g. TLC220xBCDR).
‡ Chip forms are tested at 25°C only.
TLC2202 AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax
AT 25°C
Vnmax
f = 10 Hz
AT 25°C
Vnmax
f = 1 kHz
AT 25°C
0°C to 70°C
500 µV
500 µV
1 mV
30 nV/√Hz
35 nV/√Hz
—
– 40°C to 85°C
500 µV
500 µV
1 mV
– 55°C to 125°C
500 µV
500 µV
1 mV
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(P)
12 nV/√Hz
15 nV/√Hz
—
TLC2202BCD
TLC2202ACD
TLC2202CD
—
—
—
—
—
—
TLC2202BCP
TLC2202ACP
TLC2202CP
TLC2202Y
30 nV/√Hz
35 nV/√Hz
—
12 nV/√Hz
15 nV/√Hz
—
TLC2202BID
TLC2202AID
TLC2202ID
—
—
—
—
—
—
TLC2202BIP
TLC2202AIP
TLC2202IP
—
30 nV/√Hz
35 nV/√Hz
—
12 nV/√Hz
15 nV/√Hz
—
TLC2202BMD
TLC2202AMD
TLC2202MD
TLC2202BMFK
TLC2202AMFK
TLC2202MFK
TLC2202BMJG
TLC2202AMJG
TLC2202MJG
TLC2202BMP
TLC2202AMP
TLC2202MP
—
† The D packages are available taped and reeled. Add R suffix to device type (e.g. TLC220xBCDR).
‡ Chip forms are tested at 25°C only.
2
CHIP
FORM‡
(Y)
SMALL
OUTLINE†
(D)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201
D, JG, OR P PACKAGE
(TOP VIEW)
NC
IN –
IN +
VDD – /GND
1
8
2
7
3
6
4
5
NC
VDD +
OUT
NC
TLC2202
JG OR P PACKAGE
(TOP VIEW)
1OUT
1IN –
1IN +
VDD – /GND
1
8
2
7
3
6
4
5
TLC2202
D PACKAGE
(TOP VIEW)
3 2 1 20 19
18
5
17
6
16
7
15
NC
VDD +
NC
OUT
NC
NC
1IN –
NC
1IN +
NC
13
3
12
4
11
5
10
6
9
7
8
NC
NC
VDD +
2OUT
2IN –
2IN +
NC
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
NC
2OUT
NC
2IN –
NC
NC
VDD – /GND
NC
2IN+
NC
NC
VDD – /GND
NC
NC
NC
14
8
9 10 11 12 13
14
2
TLC2202
FK PACKAGE
(TOP VIEW)
NC
NC
NC
NC
NC
4
1
NC
1OUT
NC
VDD+
NC
TLC2201
FK PACKAGE
(TOP VIEW)
NC
IN –
NC
IN +
NC
NC
NC
1OUT
1IN –
1IN +
VDD – /GND
NC
VDD +
2OUT
2IN –
2IN +
NC – No internal connection
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
equivalent schematic (each amplifier)
VDD +
Q3
Q6
Q9
Q12
Q14
Q16
IN +
OUT
C1
IN –
Q1
Q4
Q13
Q15
Q17
D1
Q7
Q8
Q10
Q11
R1
Q2
Q5
VDD – / GND
ACTUAL DEVICE COMPONENT COUNT
COMPONENT
TLC2201
TLC2202
Transistors
4
17
34
Resistors
2
2
Diodes
1
4
Capacitors
1
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
R2
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201Y chip information
This chip, when properly assembled, displays characteristics similar to the TLC2201C. Thermal compression
or ultrasonic bonding may be used on the doped-aluminum bonding path. Chips may be mounted with
conductive epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
(8)
(7)
(6)
IN –
IN +
(2)
(3)
VDD+
(7)
+
(6)
OUT
–
(4)
VDD –
77
CHIP THICKNESS: 15 MILS TYPICAL
BONDING PADS: 4 × 4 MILS MINIMUM
TJmax = 150°C
TOLERANCES ARE ± 10%.
ALL DIMENSIONS ARE IN MILS.
(1)
(2)
(3)
(4)
TERMINAL NUMBERS ARE FOR THE
D, JG, AND P PACKAGES.
65
POST OFFICE BOX 655303
PIN (4) IS INTERNALLY CONNECTED
TO BACK SIDE OF CHIP.
• DALLAS, TEXAS 75265
5
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202Y chip formation
This chip, when properly assembled, displays characteristics similar to the TLC2202C. Thermal compression
or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with
conductive epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
(8)
(7)
(6)
1IN +
(3)
(2)
1IN –
(5)
(7)
VDD+
(8)
+
(1)
1OUT
–
+
2OUT
–
(5)
(6)
2IN +
2IN –
(4)
80
VDD–
CHIP THICKNESS: 15 MILS TYPICAL
BONDING PADS: 4 × 4 MILS MINIMUM
TJmax = 150°C
(4)
TOLERANCES ARE ± 10%.
ALL DIMENSIONS ARE IN MILS.
(1)
(2)
(3)
100
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PIN (4) IS INTERNALLY CONNECTED
TO BACKSIDE OF CHIP.
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VDD + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V
Supply voltage, VDD – . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 8 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 16 V
Input voltage, VI (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 8 V
Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 5 mA
Output current, IO (each output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA
Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D or P package . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: JG package . . . . . . . . . . . . . . . . . . . . 300°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values except differential voltages are with respect to the midpoint between VDD + and VDD – .
2. Differential voltages are at IN+ with respect to IN –.
3. The output may be shorted to either supply. Temperature and /or supply voltages must be limited to ensure that the maximum
dissipation rating in not exceeded.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
TA = 125°C
POWER RATING
D–8
725 mW
5.8 mW/°C
464 mW
377 mW
145 mW
D–14
950 mW
7.6 mW/°C
608 mW
494 mW
190 mW
FK
1375 mW
11.0 mW/°C
880 mW
715 mW
275 mW
JG
1050 mW
8.4 mW/°C
672 mW
546 mW
210 mW
P
1000 mW
8.0 mW/°C
640 mW
520 mW
200 mW
recommended operating conditions
C SUFFIX
Supply voltage, VDD ±
Common-mode input voltage, VIC
Operating free-air temperature, TA
I SUFFIX
M SUFFIX
MIN
MAX
MIN
MAX
MIN
MAX
± 2.3
±8
± 2.3
±8
± 2.3
±8
VDD –
0
VDD + – 2.3
70
POST OFFICE BOX 655303
VDD –
– 40
• DALLAS, TEXAS 75265
VDD + – 2.3
85
VDD –
– 55
VDD + – 2.3
125
UNIT
V
V
°C
7
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201C electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
Input offset voltage
αVIO
Temperature coefficient of input offset voltage
TYP
MAX
100
500
Full range
Input offset voltage long-term drift (see Note 4)
IIO
Input offset current
IIB
Input bias current
VICR
Common-mode input voltage
g range
g
VOM +
Maximum positive peak output voltage swing
600
Full range
RS = 50 Ω
VIC = 0
0,
25°C
0.001
25°C
0.5
25°C
RS = 50 Ω
Maximum negative peak output voltage swing
VO = ± 4 V
V,
RL = 500 kΩ
Large signal differential voltage amplification
Large-signal
VO = ± 4 V
V,
RL = 10 kΩ
VO = 0,,
CMRR
Common mode rejection ratio
Common-mode
VIC = VICRmin,,
RS = 50 Ω
kSVR
Supply voltage rejection ratio (∆VDD ± /∆VIO)
VDD ± = ± 2
2.3
3 V to ± 8 V
IDD
Supply current
VO = 0
0,
No load
0.005
100
1
Full range
100
Full range
g
–5
to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
400
Full range
300
25°C
90
Full range
70
Full range
85
25°C
90
Full range
85
25°C
UNIT
µV
µV/°C
05
0.5
Full range
RL = 10 kΩ
AVD
TLC2201C
MIN
25°C
VIO
VOM –
TA†
µV/mo
pA
pA
V
4.8
V
– 4.9
V
560
V/mV
100
dB
110
1.1
Full range
dB
1.5
1.5
mA
† Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated
to TA = 25 °C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2201C operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
TEST CONDITIONS
VO = ± 2.3 V,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
φm
Phase margin at unity gain
† Full range is 0°C to 70°C.
8
RL = 10 kΩ,
TA†
25°C
Full range
TLC2201C
MIN
TYP
2
2.7
1.5
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
MHz
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
25°C
19
1.9
RL = 10 kΩ,
CL = 100 pF
25°C
48°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201C electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient of input
offset voltage
Input offset voltage long-term
drift (see Note 4)
IIO
Input offset current
IIB
Input bias current
VICR
Common-mode input voltage
range
VOM +
Maximum positive peak output
voltage swing
VOM –
Maximum negative
peak output
g
voltage swing
AVD
Large-signal
g
g
differential voltage
g
amplification
TEST CONDITIONS
TA†
TLC2201AC
MIN
25°C
MAX
80
200
Full range
RS = 50 Ω
25°C
RL = 500 kΩ
VO = ± 4 V
V,
RL = 10 kΩ
CMRR
Common mode rejection ratio
Common-mode
VIC = VICRmin,
VO = 0,
RS = 50 Ω
kSVR
Supply
y voltage
g rejection
j
ratio
(∆VDD ± /∆VIO)
VDD ± = ± 2
2.3
3 V to ± 8 V
IDD
Supply current
VO = 0
0,
No load
200
100
1
1
100
– 5 to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
400
Full range
300
25°C
90
Full range
70
25°C
90
Full range
85
25°C
90
Full range
85
25°C
Full range
100
– 5 to
2.7
4.8
4.7
– 4.7
4.8
400
– 4.9
90
pA
pA
V
560
300
100
µV/mo
V
– 4.7
560
µV
V
4.7
– 4.9
UNIT
µV/°C
0.5
100
25°C
VO = ± 4 V
V,
80
0.001 0.005
0.5
Full range
RL = 10 kΩ
MAX
0.5
0.001 0.005
25°C
Full range
TYP
300
0.5
Full range
RS = 50 Ω
MIN
300
Full range
VIC = 0,
TLC2201BC
TYP
V/mV
100
70
115
90
115
dB
85
110
90
110
dB
85
1.1
1.5
1.5
1.1
1.5
1.5
mA
† Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated
to TA = 25 °C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201C operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
SR
Slew rate at unity gain
Vn
Equivalent
q
input noise voltage (see Note 5)
TEST CONDITIONS
VO = ± 2.3 V,,
CL = 100 pF
RL = 10 kΩ,
TA†
25°C
Full range
TLC2201AC
MIN
TYP
2
2.7
TLC2210BC
MAX
1.5
MIN
TYP
2
2.7
MAX
UNIT
V/µs
1.5
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
Peak-to-peak equivalent
q
input f = 0.1 to 1 Hz
VN(PP)
noise voltage
f = 0.1 to 10 Hz
25°C
0.5
0.5
25°C
0.7
0.7
In
25°C
0.6
0.6
fA/√Hz
25°C
19
1.9
19
1.9
MHz
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
f = 10 kHz,,
CL = 100 pF
RL = 10 kΩ,
nV/√Hz
µV
φm
Phase margin at unity gain
RL = 10 kΩ,
CL = 100 pF
25°C
48°
48°
† Full range is 0°C to 70°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201C electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA†
TLC2201C
MIN
25°C
TYP
MAX
100
500
VIO
Input offset voltage
αVIO
Temperature coefficient of input offset voltage
Full range
Input offset voltage long-term drift (see Note 4)
25°C
0.001
25°C
0.5
Full range
Input offset current
IIB
Input bias current
VICR
Common-mode input voltage
g range
g
RS = 50 Ω
VOH
Maximum high-level
high level output voltage
RL = 10 kΩ
VOL
Maximum low-level
low level output voltage
IO = 0
AVD
RS = 50 Ω
VIC = 0
0,
IIO
600
1
Full range
Large signal differential voltage amplification
Large-signal
100
Full range
g
0
to
2.7
25°C
4.7
Full range
4.7
25°C
4.8
0
VO = 1 V to 4 V,,
RL = 10 kΩ
CMRR
Common mode rejection ratio
Common-mode
VIC = VICRmin,,
RS = 50 Ω
VO = 0,,
kSVR
Supply voltage rejection ratio (∆VDD ± /∆VIO)
VDD = 4.6
4 6 V to 16 V
IDD
Supply current
VO = 2.5
2 5 V,
V
No load
25°C
150
100
25°C
25
Full range
15
25°C
90
Full range
85
25°C
90
Full range
85
25°C
pA
pA
V
50
50
Full range
µV/mo
V
Full range
VO = 1 V to 4 V,,
RL = 500 kΩ
0.005
100
25°C
µV
µV/°C
0.5
Full range
UNIT
mV
315
V/mV
55
110
dB
110
1
Full range
dB
1.5
1.5
mA
† Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated
to TA = 25 °C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2201C operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
VO = 0.5 V to 2.5 V,
RL = 10 kΩ,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
φm
Phase margin at unity gain
† Full range is 0°C to 70°C.
TLC2201C
TA†
MIN
TYP
25°C
1.8
2.5
Full range
1.3
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
MHz
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
25°C
18
1.8
RL = 10 kΩ,
CL = 100 pF
25°C
45°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
11
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201C electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient of
input offset voltage
Input offset voltage long-term
drift (see Note 4)
TEST CONDITIONS
MIN
25°C
VIC = 0,
RS = 50 Ω
TYP
MAX
80
200
Input bias current
VICR
Common-mode input voltage
g
range
RS = 50 Ω
VOH
Maximum high-level
g
output
voltage
RL = 10 kΩ
VOL
Maximum low-level output
voltage
IO = 0
25°C
Full range
0 to
2.7
25°C
4.7
Full range
4.7
kSVR
Supplyy voltage
g rejection
j
ratio
(∆VDD ± /∆VIO)
VDD = 4
4.6
6 V to 16 V
IDD
Supply current
VO = 2.5
2 5 V,
V
No load
100
1
100
0 to
2.7
4.8
4.7
50
4.8
0
50
25°C
150
Full range
100
25°C
25
Full range
15
25°C
90
Full range
85
25°C
90
Full range
85
25°C
Full range
315
50
25
pA
pA
mV
315
100
55
µV/mo
V
50
150
µV
V
4.7
0
UNIT
µV/°C
0.5
100
Full range
Common mode rejection ratio
Common-mode
200
0.001 0.005
1
25°C
CMRR
80
100
25°C
VIC = VICRmin,
VO = 0,
RS = 50 Ω
MAX
05
0.5
0.5
Full range
VO = 1 V to 4 V,,
RL = 10 kΩ
TYP
300
0.001 0.005
Full range
VO = 1 V to 4 V,,
RL = 500 kΩ
MIN
05
0.5
25°C
IIB
TLC2201BC
300
Full range
Input offset current
Large-signal
g
g
differential
voltage amplification
TLC2201AC
Full range
IIO
AVD
TA†
V/mV
55
15
110
90
110
dB
85
110
90
110
dB
85
1
1.5
1.5
1
1.5
1.5
mA
† Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated
to TA = 25 °C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201C operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
TA†
SR
Slew rate at unity gain
VO = 0.5 V to 2.5 V,
RL = 10 kΩ, CL = 100 pF
Vn
Equivalent
q
input noise voltage
g
(see Note 5)
Peak-to-peak equivalent
q
input
VN(PP)
noise voltage
In
TYP
25°C
1.8
2.5
Full range
1.3
TLC2210BC
MAX
MIN
TYP
1.8
2.5
MAX
UNIT
V/µs
1.3
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
25°C
0.6
0.6
fA/√Hz
25°C
1.8
1.8
MHz
Equivalent input noise current
Gain-bandwidth product
TLC2201AC
MIN
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
nV/√Hz
µV
φm
Phase margin at unity gain
RL = 10 kΩ, CL = 100 pF
25°C
45°
45°
† Full range is 0°C to 70°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202C electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless
otherwise specified)
PARAMETER
VIO
αVIO
TEST CONDITIONS
Temperature coefficient of input offset voltage
RS = 50 Ω
VIC = 0
0,
Input offset current
RS = 50 Ω
VIC = 0
0,
IIB
Input bias current
RS = 50 Ω
Common-mode input voltage
g range
g
VOM +
Maximum positive peak output voltage swing
RL = 10 kΩ
AVD
TYP
MAX
100
1000
Full range
1150
Full range
0.001
25°C
0.5
Full range
Maximum negative peak output voltage swing
VO = ± 4 V
V,
RL = 500 kΩ
VO = ± 4 V
V,
RL = 10 kΩ
Large signal differential voltage amplification
Large-signal
CMRR
Common mode rejection ratio
Common-mode
VO = 0,,
RS = 50 Ω
VIC = VICRmin,,
kSVR
Supply voltage rejection ratio (∆VDD ± /∆VIO)
Supply-voltage
VDD ± = ± 2
2.3
3 V to ± 8 V
IDD
Supply current
VO = 0
0,
No load
0.005
100
25°C
UNIT
µV
µV/°C
0.5
25°C
1
Full range
VICR
VOM –
TLC2202C
MIN
25°C
Input offset voltage
Input offset voltage long-term drift (see Note 4)
IIO
TA†
µV/mo
pA
100
Full range
g
–5
to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
300
Full range
200
25°C
50
Full range
25
25°C
80
Full range
80
25°C
80
Full range
80
V
4.8
V
– 4.9
V
560
V/mV
100
115
dB
110
25°C
1.8
Full range
dB
2.7
2.7
mA
† Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated
to TA = 25 °C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2202C operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
TEST CONDITIONS
VO = ± 2.3 V,,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
φm
Phase margin at unity gain
† Full range is 0°C to 70°C.
14
RL = 10 kΩ,,
TA†
TLC2202C
MIN
TYP
25°C
1.8
2.7
Full range
1.3
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
MHz
f = 10 kHz,,
CL = 100 pF
RL = 10 kΩ,,
25°C
19
1.9
RL = 10 kΩ,
CL = 100 pF
25°C
48°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202C electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless
otherwise noted)
PARAMETER
VIO
Input
In
ut offset voltage
αVIO
Temperature coefficient
of input offset voltage
TEST CONDITIONS
25°C
VIC = 0
0,
RS = 50 Ω
Input
In
ut bias current
VICR
Common-mode
Common
mode input voltage
range
VOM +
Maximum positive peak
output voltage swing
VOM –
AVD
Maximum negative
peak
g
output voltage swing
Large-signal
differential
g
g
voltage amplification
Full range
MAX
80
500
RS = 50 Ω
RL = 10 kΩ
VO = ± 4 V,
V
RL = 500 kΩ
VO = ± 4 V,
V
RL = 10 kΩ
CMRR
Common-mode rejection ratio
VIC = VICRmin,
VO = 0,
RS = 50 Ω
kSVR
Supply-voltage
y
g rejection
j
ratio
(∆VDD ± /∆VIO)
VDD ± = ± 2
2.3
3 V to ± 8 V
IDD
Supply
Su
ly current
VO = 0
0,
No load
TYP
MAX
80
500
650
0.001 0.005
0.001 0.005
0.5
0.5
Full range
100
25°C
100
1
1
100
Full range
–5
to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
300
Full range
200
25°C
50
Full range
25
25°C
80
Full range
80
25°C
80
Full range
80
25°C
100
–5
to
2.7
4.8
4.7
– 4.7
4.8
300
– 4.9
50
pA
A
pA
A
V
560
200
100
µV/mo
V
– 4.7
560
µV
V
4.7
– 4.9
UNIT
µV/°C
05
0.5
Full range
RS = 50 Ω
MIN
05
0.5
25°C
VIC = 0
0,
TLC2202BC
TYP
650
25°C
Input
In
ut offset current
IIB
TLC2202AC
MIN
Full range
Input offset voltage long-term
drift (see Note 4)
IIO
TA†
V/mV
100
25
115
80
115
dB
80
110
80
110
dB
80
1.8
2.7
Full range
1.8
2.7
2.7
2.7
mA
† Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2202C operating characteristics at specified free-air temperature, VDD± = ±5 V
PARAMETER
TLC2202AC
TEST CONDITIONS
TA†
MIN
TYP
VO = ± 2
2.3
3V
V,
RL = 10 kΩ, CL = 100 pF
25°C
18
1.8
27
2.7
Full range
1.3
TLC2202BC
MAX
MIN
TYP
18
1.8
27
2.7
MAX
UNIT
SR
Slew rate at unity gain
Vn
Equivalent
q
input noise voltage
g
(see Note 5)
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
VN(PP)
Peak-to-peak equivalent
q
input
noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
25°C
0.6
0.6
fA/√Hz
25°C
1.9
1.9
MHz
Gain-bandwidth product
f = 10 kHz,
kHz RL = 10 kΩ
kΩ,
CL = 100 pF
V/µs
1.3
nV/√Hz
µV
φm
Phase margin at unity gain
RL = 10 kΩ,
kΩ CL = 100 pF
F
25°C
48°
48°
† Full range is 0°C to 70°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202C electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
VIO
αVIO
TEST CONDITIONS
TLC2202C
MIN
TYP
MAX
100
1000
25°C
Input offset voltage
Temperature coefficient of input offset voltage
RS = 50 Ω
VIC = 0
0,
Input offset voltage long-term drift (see Note 4)
Full range
1150
Full range
Input offset current
IIB
Input bias current
VICR
Common-mode input voltage
g range
g
RS = 50 Ω
VOH
Maximum high
high-level
level output voltage
RL = 10 kΩ
VOL
Maximum low-level
low level output voltage
IO = 0
0.001
0.005
Full range
RS = 50 Ω
VIC = 0,
Large signal differential voltage amplification
Large-signal
25°C
100
Full range
g
0
to
2.7
25°C
4.7
Full range
4.7
V
4.8
25°C
CMRR
Common mode rejection ratio
Common-mode
VO = 0,,
RS = 50 Ω
VIC = VICRmin,,
kSVR
Supply voltage rejection ratio (∆VDD ± /∆VIO)
Supply-voltage
VDD= 4.6
4 6 V to 16 V
IDD
Supply current
VO = 0
0,
No load
µV/mo
pA
1
0
Full range
VO = 1 V to 4 V,,
RL = 10 kΩ
µV
100
Full range
VO =1 V to 4 V,,
RL = 500 kΩ
UNIT
µV/°C
0.5
25°C
IIO
AVD
TA†
V
50
50
25°C
150
Full range
100
25°C
25
Full range
15
25°C
75
Full range
75
25°C
80
Full range
80
mV
315
V/mV
55
110
dB
110
25°C
1.7
Full range
dB
2.6
2.6
mA
† Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2202C operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
VO = 0.5 V to 2.5 V,,
RL = 10 kΩ,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
φm
Phase margin at unity gain
† Full range is 0°C to 70°C.
16
TA†
TLC2202C
MIN
TYP
25°C
1.6
2.5
Full range
1.1
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
MHz
f = 10 kHz,,
CL = 100 pF
RL = 10 kΩ,,
25°C
19
1.9
RL = 10 kΩ,
CL = 100 pF
25°C
47°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202C electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
VIO
Input
In
ut offset voltage
αVIO
Temperature coefficient
of input offset voltage
TEST CONDITIONS
TLC2202AC
MIN
25°C
VIC = 0
0,
RS = 50 Ω
MAX
80
500
Full range
IIB
Input
In
ut bias current
VICR
Common-mode
Common
mode input
voltage range
RS = 50 Ω
VOH
Maximum high-level
g
output voltage
RL = 10 kΩ
VOL
Maximum low-level
output voltage
IO = 0
AVD
Large-signal
g
g
differential
voltage amplification
RS = 50 Ω
0.001 0.005
CMRR
Common-mode rejection ratio
kSVR
Supply-voltage
ratio
y
g rejection
j
(∆VDD ± /∆VIO)
4 6 V to 16 V
VDD = 4.6
IDD
Supply
Su
ly current
VO = 2.5
2 5 V,
V
No load
500
25°C
0.5
100
1
1
100
Full range
0
to
2.7
25°C
4.7
Full range
4.7
100
0
to
2.7
4.8
4.7
50
4.8
25°C
150
100
25°C
25
Full range
15
25°C
75
Full range
75
25°C
80
Full range
80
25°C
315
0
50
50
150
25
pA
A
pA
A
mV
315
100
55
µV/mo
V
50
Full range
µV
V
4.7
0
UNIT
µV/°C
100
Full range
VIC = VICRmin,
VO = 0,
RS = 50 Ω
80
0.001 0.005
0.5
Full range
25°C
VO = 1 V to 4 V,
RL = 10 kΩ
MAX
05
0.5
Full range
VO = 1 V to 4 V,
RL = 500 kΩ
TYP
650
05
0.5
25°C
VIC = 0
0,
MIN
650
25°C
Input
In
ut offset current
TLC2202BC
TYP
Full range
Input offset voltage
long-term drift (see Note 4)
IIO
TA†
V/mV
55
15
110
75
110
dB
75
110
80
110
dB
80
1.7
2.6
Full range
1.7
2.6
2.6
2.6
mA
† Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2202C operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TLC2202AC
TEST CONDITIONS
TA†
MIN
TYP
VO = 0.5
0 5 V to 2
2.5
5 V,
V
RL = 10 kΩ, CL = 100 pF
25°C
16
1.6
25
2.5
Full range
1.1
TLC2202BC
MAX
MIN
TYP
16
1.6
25
2.5
MAX
UNIT
SR
Slew rate at unity gain
Vn
Equivalent
q
input noise voltage
g
(see Note 5)
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
VN(PP)
Peak-to-peak equivalent
input
q
noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
25°C
0.6
0.6
fA/√Hz
25°C
1.9
1.9
MHz
Gain-bandwidth product
f = 10 kHz,
kHz RL = 10 kΩ
kΩ,
CL = 100 pF
V/µs
1.1
nV/√Hz
µV
kΩ CL = 100 pF
φm
Phase margin at unity gain
RL = 10 kΩ,
F
25°C
47°
47°
† Full range is 0°C to 70°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201I electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
Input offset voltage
αVIO
Temperature coefficient of input offset voltage
TYP
MAX
100
500
Full range
Input offset voltage long-term drift (see Note 4)
IIO
Input offset current
IIB
Input bias current
VICR
Common-mode input voltage
g range
g
VOM +
Maximum positive peak output voltage swing
650
Full range
RS = 50 Ω
VIC = 0
0,
25°C
0.001
25°C
0.5
25°C
RS = 50 Ω
Maximum negative peak output voltage swing
VO = ± 4 V
V,
RL = 500 kΩ
Large signal differential voltage amplification
Large-signal
VO = ± 4 V
V,
RL = 10 kΩ
CMRR
Common mode rejection ratio
Common-mode
VIC = VICRmin,
VO = 0,
RS = 50 Ω
kSVR
Supply voltage rejection ratio (∆VDD ± /∆VIO)
VDD ± = ± 2
2.3
3 V to ± 8 V
IDD
Supply current
VO = 0
0,
No load
0.005
150
1
Full range
150
Full range
g
–5
to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
400
Full range
250
25°C
90
Full range
65
25°C
90
Full range
85
25°C
90
Full range
85
25°C
UNIT
µV
µV/°C
05
0.5
Full range
RL = 10 kΩ
AVD
TLC2201I
MIN
25°C
VIO
VOM –
TA†
µV/mo
pA
pA
V
4.8
V
– 4.9
V
560
V/mV
100
115
dB
110
1.1
Full range
dB
1.5
1.5
mA
† Full range is – 40°C to 85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2201I operating characteristics at specified free-air temperature, VDD ± = ±5 V
PARAMETER
TEST CONDITIONS
VO = ± 2.3 V,,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
φm
Phase margin at unity gain
† Full range is – 40°C to 85°C.
18
RL = 10 kΩ,
TA†
25°C
Full range
TLC2201I
MIN
TYP
2
2.7
1.4
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
MAX
UNIT
V/µs
nV/√Hz
µV
25°C
0.6
fA/√Hz
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
25°C
19
1.9
MHz
RL = 10 kΩ,
CL = 100 pF
25°C
48°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201I electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise
noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient of input
offset voltage
Input offset voltage long-term
drift (see Note 4)
IIO
Input offset current
IIB
Input bias current
VICR
input
Common-mode in
ut voltage
range
VOM +
Maximum positive peak output
voltage swing
VOM –
Maximum negative
g
peak output
voltage swing
AVD
Large-signal
g
g
differential voltage
g
amplification
Common mode rejection ratio
CMRR Common-mode
TEST CONDITIONS
TA†
TLC2201AI
MIN
25°C
MAX
80
200
Full range
RS = 50 Ω
25°C
VO = ± 4 V
V,
RL = 500 kΩ
RL = 10 kΩ
VIC = VICRmin,
VO = 0,
RS = 50 Ω
kSVR
Supplyy voltage
g rejection
j
ratio
(∆VDD ± /∆VIO)
VDD ± = ± 2
2.3
3 V to ± 8 V
IDD
Supply current
VO = 0
0,
No load
200
150
1
1
150
– 5 to
2.7
2
7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
400
Full range
250
25°C
90
Full range
65
25°C
90
Full range
85
25°C
90
Full range
85
25°C
Full range
150
– 5 to
2.7
2
7
4.8
4.7
– 4.7
4.8
400
– 4.9
90
pA
pA
V
560
250
100
µV/mo
V
– 4.7
560
µV
V
4.7
– 4.9
UNIT
µV/°C
0.5
150
25°C
VO = ± 4 V
V,
80
0.001 0.005
0.5
Full range
RL = 10 kΩ
MAX
05
0.5
0.001 0.005
25°C
g
Full range
TYP
350
05
0.5
Full range
RS = 50 Ω
MIN
350
Full range
VIC = 0,
TLC2210BI
TYP
V/mV
100
65
115
90
115
dB
85
110
90
110
dB
85
1.1
1.5
1.5
1.1
1.5
1.5
mA
† Full range is – 40°C to 85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated
to TA = 25°C using the Arrhenius equation assuming an activation energy of 0.96 eV.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201I operating characteristics at specified free-air temperature, VDD ± = ±5 V
PARAMETER
TEST CONDITIONS
TA†
SR
Slew rate at unity gain
VO = ± 2.3 V,
RL = 10 kΩ, CL = 100 pF
25°C
Vn
Equivalent
input noise voltage
q
g
(see Note 5)
Peak-to-peak equivalent
q
input
VN(PP)
noise voltage
In
TYP
2
2.7
TLC2210BI
MAX
1.4
MIN
TYP
2
2.7
MAX
UNIT
V/µs
1.4
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
25°C
0.6
0.6
fA/√Hz
25°C
19
1.9
19
1.9
MHz
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
Full range
TLC2201AI
MIN
f = 10 kHz,
RL = 10 kΩ,
CL = 100 pF
nV/√Hz
µV
φm
Phase margin at unity gain
RL = 10 kΩ, CL = 100 pF
25°C
48°
48°
† Full range is – 40°C to 85°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
20
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201I electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA†
TLC2201I
MIN
25°C
TYP
MAX
100
500
VIO
Input offset voltage
αVIO
Temperature coefficient of input offset voltage
Full range
Input offset voltage long-term drift (see Note 4)
25°C
0.001
25°C
0.5
Full range
Input offset current
IIB
Input bias current
VICR
Common-mode input voltage
g range
g
RS = 50 Ω
VOH
Maximum high-level
high level output voltage
RL = 10 kΩ
VOL
Maximum low-level
low level output voltage
IO = 0
AVD
RS = 50 Ω
VIC = 0
0,
IIO
650
1
Full range
Large signal differential voltage amplification
Large-signal
150
Full range
g
0
to
2.7
25°C
4.7
Full range
4.7
4.8
0
Full range
VO = 1 V to 4 V,,
RL = 10 kΩ
CMRR
Common mode rejection ratio
Common-mode
VIC = VICRmin,
VO = 0,
RS = 50 Ω
kSVR
Supply voltage rejection ratio (∆VDD ± /∆VIO)
VDD = 4
4.6
6 V to 16 V
IDD
Supply current
VO = 2
2.5
5V
V,
No load
25°C
150
100
25°C
25
Full range
15
25°C
90
Full range
85
25°C
90
Full range
85
pA
pA
V
50
50
Full range
µV/mo
V
25°C
VO = 1 V to 4 V,,
RL = 500 kΩ
0.005
150
25°C
µV
µV/°C
0.5
Full range
UNIT
mV
315
V/mV
55
110
dB
110
25°C
1
Full range
dB
1.5
1.5
mA
† Full range is – 40°C to 85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2201I operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
VO = 0.5 V to 2.5 V,
RL = 10 kΩ,,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
φm
Phase margin at unity gain
† Full range is – 40°C to 85°C.
TLC2201I
TA†
MIN
TYP
25°C
1.8
2.5
Full range
1.2
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
MHz
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
25°C
18
1.8
RL = 10 kΩ,
CL = 100 pF
25°C
45°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
21
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201I electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
VIO
Input
In
ut offset voltage
αVIO
Temperature coefficient of
input offset voltage
Input offset voltage long-term
drift (see Note 4)
TEST CONDITIONS
TLC2201AI
MIN
25°C
MAX
80
200
RS = 50 Ω
IIB
Input
In
ut bias current
VICR
Common-mode
Common
mode input voltage
range
RS = 50 Ω
VOH
Maximum high-level
g
output
voltage
RL = 10 kΩ
VOL
Maximum low-level output
voltage
IO = 0
AVD
Large-signal
g
g
differential
voltage amplification
25°C
Full range
0
to
2.7
25°C
4.7
Full range
4.7
25°C
Supplyy voltage
ratio
g rejection
j
(∆VDD ± /∆VIO)
6 V to 16 V
VDD = 4
4.6
IDD
Supply
Su
ly current
VO = 2.5
25V
V,
No load
150
1
150
150
0
to
2.7
4.8
4.7
50
4.8
0
50
25°C
150
Full range
100
25°C
25
Full range
15
25°C
90
Full range
85
25°C
90
Full range
85
25°C
Full range
315
50
25
pA
A
pA
A
mV
315
100
55
µV/mo
V
50
150
µA
V
4.7
0
UNIT
µV/°C
0.5
1
Full range
kSVR
200
150
25°C
VIC = VICRmin,
VO = 0,
RS = 50 Ω
80
0.001 0.005
0.5
Full range
VO = 1 V to 4 V,
RL = 10 kΩ
MAX
05
0.5
0.001 0.005
Full range
VO = 1 V to 4 V,
RL = 500 kΩ
TYP
350
05
0.5
25°C
Input
In
ut offset current
MIN
350
Full range
VIC = 0,
TLC2201BI
TYP
Full range
IIO
CMRR Common-mode rejection ratio
TA†
V/mV
55
15
110
90
110
dB
85
110
90
110
dB
85
1
1.5
1.5
1
1.5
1.5
mA
† Full range is – 40°C to 85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
22
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201I operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
SR
Slew rate at unity gain
Vn
Equivalent
q
input noise
voltage (see Note 5)
TEST CONDITIONS
TA†
VO = 0.5 V to 2.5 V,
RL = 10 kΩ, CL = 100 pF
TLC2201AI
MIN
TYP
25°C
1.8
2.5
Full range
1.2
TLC2210BI
MAX
MIN
TYP
1.8
2.5
MAX
UNIT
V/µs
1.2
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
Peak-to-peak equivalent
q
input f = 0.1 to 1 Hz
VN(PP)
noise voltage
f = 0.1 to 10 Hz
25°C
0.5
0.5
25°C
0.7
0.7
In
25°C
0.6
0.6
fA/√Hz
25°C
18
1.8
18
1.8
MHz
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
f = 10 kHz,,
CL = 100 pF
RL = 10 kΩ,
nV/√Hz
µV
φm
CL = 100 pF
kΩ
Phase margin at unity gain
RL = 10 kΩ,
25°C
45°
45°
† Full range is – 40°C to 85°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
23
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202I electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
Input offset voltage
αVIO
Temperature coefficient of input offset voltage
RS = 50 Ω
VIC = 0
0,
Input offset voltage long-term drift (see Note 4)
Input offset current
IIB
Input bias current
MAX
100
1000
Full range
1200
Full range
0.001
RS = 50 Ω
VOM +
Maximum positive peak output voltage swing
RL = 10 kΩ
Maximum negative peak output voltage swing
VO = ± 4 V
V,
RL = 500 kΩ
Large signal differential voltage amplification
Large-signal
VO = ± 4 V
V,
RL = 10 kΩ
VIC = VICRmin,,
CMRR
Common mode rejection ratio
Common-mode
VO = 0,,
RS = 50 Ω
kSVR
Supply voltage rejection ratio (∆VDD ± /∆VIO)
Supply-voltage
3 V to ± 8 V
VDD = ± 2
2.3
IDD
Supply current
VO = 0
0,
No load
µV
0.005
µV/mo
150
pA
1
25°C
Full range
RS = 50 Ω
UNIT
µV/°C
0.5
25°C
VIC = 0,
Common-mode input voltage
g range
g
AVD
TYP
Full range
VICR
VOM –
TLC2202I
MIN
25°C
VIO
IIO
TA†
150
Full range
g
–5
to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
300
Full range
150
25°C
50
Full range
25
25°C
80
Full range
80
25°C
80
Full range
80
25°C
V
4.8
V
– 4.9
V
560
V/mV
100
115
dB
110
1.8
Full range
dB
2.7
2.7
mA
† Full range is – 40°C to 85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2202I operating characteristics at specified free-air temperature, VDD ± = ±5 V
PARAMETER
TEST CONDITIONS
VO = ± 2.3 V,,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
φm
Phase margin at unity gain
† Full range is – 40°C to 85°C.
24
RL = 10 kΩ,,
TA†
TLC2202I
MIN
TYP
25°C
1.8
2.7
Full range
1.2
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
MHz
f = 10 kHz,,
CL = 100 pF
RL = 10 kΩ,,
25°C
19
1.9
RL = 10 kΩ,
CL = 100 pF
25°C
48°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202I electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise
noted)
PARAMETER
VIO
Input
In
ut offset voltage
αVIO
Temperature coefficient
of input offset voltage
TEST CONDITIONS
25°C
VIC = 0
0,
RS = 50 Ω
Input
In
ut bias current
VICR
Common-mode
Common
mode input
voltage range
VOM +
Maximum positive peak
output voltage swing
VOM –
Maximum negative
peak
g
output voltage swing
AVD
Large-signal
g
g
differential
voltage amplification
Full range
MAX
80
500
RS = 50 Ω
RL = 10 kΩ
VO = ± 4 V,
RL = 500 kΩ
VO = ± 4 V,
RL = 10 kΩ
CMRR
Common-mode rejection ratio
VIC = VICRmin,
VO = 0,
RS = 50 Ω
kSVR
Supply-voltage
ratio
y
g rejection
j
(∆VDD ± /∆VIO)
3 V to ± 8 V
VDD ± ± 2
2.3
IDD
Supply
Su
ly current
VO = 0
0,
No load
TYP
MAX
80
500
700
0.001 0.005
0.001 0.005
0.5
0.5
Full range
150
25°C
150
1
1
150
Full range
–5
to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
300
Full range
150
25°C
50
Full range
25
25°C
80
Full range
80
25°C
80
Full range
80
25°C
150
–5
to
2.7
4.8
4.7
– 4.7
4.8
300
– 4.9
50
pA
A
pA
A
V
560
150
100
µV/mo
V
– 4.7
560
µV
V
4.7
– 4.9
UNIT
µV/°C
05
0.5
Full range
RS = 50 Ω
MIN
05
0.5
25°C
VIC = 0
0,
TLC2202BI
TYP
700
25°C
Input
In
ut offset current
IIB
TLC2202AI
MIN
Full range
Input offset voltage long-term
drift (see Note 4)
IIO
TA†
V/mV
100
25
115
80
115
dB
80
110
80
110
dB
80
1.8
2.7
Full range
1.8
2.7
2.7
2.7
mA
† Full range is – 40°C to 85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2202I operating characteristics at specified free-air temperature, VDD ± = ±5 V
PARAMETER
TLC2202AI
TEST CONDITIONS
TA†
MIN
TYP
VO = ± 2
2.3
3V
V, RL = 10 kΩ
kΩ,
CL = 100 pF
25°C
18
1.8
27
2.7
Full range
1.2
TLC2202BI
MAX
MIN
TYP
18
1.8
27
2.7
MAX
UNIT
SR
Slew rate at unity gain
Vn
Equivalent
q
input noise voltage
g
(see Note 5)
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
VN(PP)
Peak-to-peak equivalent
q
input noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
25°C
0.6
0.6
fA/√Hz
25°C
1.9
1.9
MHz
Gain-bandwidth product
f = 10 kHz,
kHz RL = 10 kΩ
kΩ,
CL = 100 pF
V/µs
1.2
nV/√Hz
µV
kΩ CL = 100 pF
φm
Phase margin at unity gain
RL = 10 kΩ,
F
25°C
48°
48°
† Full range is – 40°C to 85°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
25
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202I electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
VIO
αVIO
TEST CONDITIONS
TLC2202I
MIN
25°C
Input offset voltage
Temperature coefficient of input offset voltage
RS = 50 Ω
VIC = 0
0,
Input offset voltage long-term drift (see Note 4)
Input offset current
IIB
Input bias current
VICR
Common-mode input voltage
g range
g
RS = 50 Ω
VOH
Maximum high
high-level
level output voltage
RL = 10 kΩ
VOL
Maximum low-level
low level output voltage
IO = 0
TYP
MAX
100
1000
Full range
1200
Full range
0.001
Full range
RS = 50 Ω
VIC = 0,
Large signal differential voltage amplification
Large-signal
25°C
Common mode rejection ratio
Common-mode
VO = 0,,
RS = 50 Ω
VIC = VICRmin,,
kSVR
Supply voltage rejection ratio (∆VDD ± /∆VIO)
Supply-voltage
VDD= 4.6
4 6 V to 16 V
IDD
Supply current
VO = 2.5
25V
V,
No load
µV/mo
pA
150
Full range
g
0
to
2.7
25°C
4.7
Full range
4.7
V
4.8
25°C
CMRR
0.005
1
0
Full range
VO = 1 V to 4 V,,
RL = 10 kΩ
µV
150
Full range
VO =1 V to 4 V,,
RL = 500 kΩ
UNIT
µV/°C
0.5
25°C
IIO
AVD
TA†
V
50
50
25°C
150
Full range
100
25°C
25
Full range
15
25°C
75
Full range
75
25°C
80
Full range
80
mV
315
V/mV
55
110
dB
110
25°C
1.7
Full range
dB
2.6
2.6
mA
† Full range is – 40°C to 85°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2202I operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
φm
Phase margin at unity gain
† Full range is – 40°C to 85°C.
26
TEST CONDITIONS
TA†
VO = 0.5 V to 2.5 V,,
RL = 10 kΩ,
CL = 100 pF
25°C
Full range
TLC2202I
MIN
TYP
1.6
2.5
1
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
MAX
UNIT
V/µs
nV/√Hz
µV
25°C
0.6
fA/√Hz
f = 10 kHz,,
CL = 100 pF
RL = 10 kΩ,,
25°C
19
1.9
MHz
RL = 10 kΩ,
CL = 100 pF
25°C
47°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202I electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
VIO
Input
In
ut offset voltage
αVIO
Temperature coefficient of
input offset voltage
TEST CONDITIONS
25°C
VIC = 0
0,
RS = 50 Ω
IIB
Input
In
ut bias current
VICR
Common-mode
Common
mode input
voltage range
RS = 50 Ω
VOH
Maximum high-level
g
output
voltage
RL = 10 kΩ
VOL
Maximum low-level output
voltage
IO = 0
Large-signal
differential
g
g
voltage amplification
Full range
MAX
80
500
RS = 50 Ω
CMRR
Common-mode rejection ratio
kSVR
Supply-voltage
y
g rejection
j
ratio
(∆VDD ± /∆VIO)
VDD = 4.6
4 6 V to 16 V
IDD
Supply
Su
ly current
VO = 2.5
2 5 V,
V
No load
80
500
0.5
150
25°C
150
1
1
150
Full range
0
to
2.7
25°C
4.7
Full range
4.7
150
0
to
2.7
4.8
4.7
50
4.8
25°C
150
100
25°C
25
Full range
15
25°C
75
Full range
75
25°C
80
Full range
80
25°C
315
0
50
50
150
25
pA
A
pA
A
mV
315
100
55
µV/mo
V
50
Full range
µV
V
4.7
0
UNIT
µV/°C
0.001 0.005
0.5
Full range
25°C
VIC = VICRmin,
VO = 0,
RS = 50 Ω
MAX
700
0.001 0.005
Full range
VO =1 V to 4 V,
RL = 10 kΩ
TYP
05
0.5
Full range
VO = 1 V to 4 V,
RL = 500 kΩ
MIN
05
0.5
25°C
Input
In
ut offset current
TLC2202BI
TYP
700
25°C
VIC = 0
0,
AVD
TLC2202AI
MIN
Full range
Input offset voltage long-term
drift (see Note 4)
IIO
TA†
V/mV
55
15
110
75
110
dB
75
110
80
110
dB
80
1.7
2.6
Full range
1.7
2.6
2.6
2.6
mA
† Full range is – 40°C to 85°C
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2202I operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TLC2202AI
TEST CONDITIONS
TA†
MIN
TYP
VO = 0.5
0 5 V to 2
2.5
5 V,
V
RL = 10 kΩ, CL = 100 pF
25°C
16
1.6
25
2.5
TLC2202BI
MAX
MIN
TYP
16
1.6
25
2.5
MAX
UNIT
SR
Slew rate at unity gain
Vn
Equivalent
q
input noise voltage
g
(see Note 5)
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
VN(PP)
Peak-to-peak equivalent
q
input noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
25°C
0.6
0.6
fA/√Hz
25°C
1.9
1.9
MHz
Gain-bandwidth product
f = 10 kHz,
kHz RL = 10 kΩ
kΩ,
CL = 100 pF
Full range
1
V/µs
1
nV/√Hz
µV
φm
Phase margin at unity gain
RL = 10 kΩ,
kΩ CL = 100 pF
F
25°C
47°
47°
† Full range is – 40°C to 85°C
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
27
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201M electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLC2201M
MIN
25°C
TYP
MAX
100
500
VIO
Input offset voltage
αVIO
Temperature coefficient of input offset voltage
Full range
Input offset voltage long-term drift (see Note 4)
25°C
0.001
25°C
0.5
Full range
IIO
Input offset current
IIB
Input bias current
VICR
Common-mode input voltage
g range
g
VOM +
Maximum positive peak output voltage swing
VOM –
Maximum negative peak output voltage swing
RS = 50 Ω
VIC = 0
0,
1
Full range
RS = 50 Ω
VO = ± 4 V
V,
RL = 500 kΩ
VO = ± 4 V
V,
RL = 10 kΩ
Large signal differential voltage amplification
Large-signal
CMRR
Common mode rejection ratio
Common-mode
VIC = VICRmin,
VO = 0,
RS = 50 Ω
kSVR
Supply voltage rejection ratio (∆VDD ± /∆VIO)
VDD ± = ± 2
2.3
3 V to ± 8 V
IDD
Supply current
VO = 0
0,
No load
0.005
500
25°C
500
Full range
g
–5
to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
400
Full range
200
25°C
90
Full range
45
25°C
90
Full range
85
25°C
90
Full range
85
µV
µV/°C
0.5
Full range
RL = 10 kΩ
AVD
700
UNIT
µV/mo
pA
pA
V
4.8
V
– 4.9
V
560
V/mV
100
115
dB
110
25°C
1.1
Full range
dB
1.5
1.5
mA
† Full range is – 55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2201M operating characteristics at specified free-air temperature, VDD ± = ±5 V
PARAMETER
TEST CONDITIONS
VO = ± 2.3 V,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
φm
Phase margin
† Full range is – 55°C to 125°C.
28
RL = 10 kΩ,
TA†
25°C
Full range
TLC2201M
MIN
TYP
2
2.7
1.3
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
MHz
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
25°C
19
1.9
RL = 10 kΩ,
CL = 100 pF
25°C
48°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201M electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless
otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient of
input offset voltage
Input offset voltage
long-term drift (see Note 4)
IIO
Input offset current
IIB
Input bias current
VICR
Common mode input
Common-mode
voltage range
VOM
OM+
Maximum positive peak
output voltage swing
VOM –
AVD
Maximum negative
g
peak
output voltage swing
Large-signal
g
g
differential
voltage amplification
TA†
TEST CONDITIONS
TLC2201AM
MIN
25°C
TYP
MAX
80
200
Full range
RS = 50 Ω
25°C
0.001
25°C
0.5
25°C
Full range
g
–5
to
2.7
25°C
4.7
Full range
4.7
– 4.7
– 4.7
25°C
400
Full range
200
VO = ± 4 V,,
RL = 10 kΩ
25°C
90
Full range
45
25°C
90
Full range
85
25°C
90
Full range
85
Common-mode rejection
j
ratio
VIC = VICRmin,
RS = 50 Ω
VO = 0,
kSVR
Supplyy voltage
g rejection
j
ratio (∆VDD ± /∆VIO)
VDD ± = ± 2
2.3
3 V to ± 8 V
IDD
Supply current
VO = 0
0,
No load
200
0.005
0.001
25°C
Full range
0.005
500
1
500
–5
to
2.7
4.8
4.7
– 4.7
4.8
400
– 4.9
90
pA
pA
V
560
200
100
µV/mo
V
– 4.7
560
µV
V
4.7
– 4.9
UNIT
µV/°C
0.5
500
25°C
CMRR
80
05
0.5
1
Full range
VO = ± 4 V,,
RL = 500 kΩ
MAX
500
Full range
RL = 10 kΩ
TYP
400
05
0.5
Full range
RS = 50 Ω
MIN
400
Full range
VIC = 0,
TLC2210BM
V/mV
100
45
115
90
115
dB
85
110
90
110
dB
85
1.1
1.5
1.5
1.1
1.5
1.5
mA
† Full range is – 55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observable through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
29
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201M operating characteristics at specified free-air temperature, VDD ± = ±5 V
PARAMETER
SR
Slew rate at unity gain
TEST
CONDITIONS
VO = ± 2.3
23V
V,
RL = 10 kΩ,
kΩ
CL = 100 pF
TA†
25°C
TLC2201AM
MIN
TYP
2
27
2.7
TLC2201BM
MAX
MIN
TYP
2
27
2.7
MAX
UNIT
V/µs
Full range
1.3
1.3
Vn
Equivalent
q
input noise voltage
g
(see Note 5)
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
VN(PP)
Peak-to-peak equivalent
q
input
noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
25°C
0.6
0.6
fA/√Hz
MHz
φm
Gain-bandwidth product
f = 10 kHz,
RL = 10 kΩ,,
CL = 100 pF
25°C
1.9
1.9
Phase margin at unity gain
RL = 10 kΩ,
CL = 100 pF
25°C
48°
48°
nV/√Hz
µV
† Full range is – 55°C to 125°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
30
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201M electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA†
TLC2201M
MIN
25°C
TYP
MAX
100
500
VIO
Input offset voltage
αVIO
Temperature coefficient of input offset voltage
Full range
Input offset voltage long-term drift (see Note 4)
25°C
0.001
25°C
0.5
Full range
Input offset current
IIB
Input bias current
VICR
Common-mode input voltage
g range
g
RS = 50 Ω
VOH
Maximum high-level
high level output voltage
RL = 10 kΩ
VOL
Maximum low-level
low level output voltage
IO = 0
AVD
RS = 50 Ω
VIC = 0
0,
IIO
700
0.005*
Full range
500
1
Full range
Large signal differential voltage amplification
Large-signal
500
Full range
g
0
to
2.7
25°C
4.7
Full range
4.7
4.8
0
Full range
VO = 1 V to 4 V,,
RL = 10 kΩ
CMRR
Common mode rejection ratio
Common-mode
VIC = VICRmin,
VO = 0,
RS = 50 Ω
kSVR
Supply voltage rejection ratio (∆VDD ± /∆VIO)
VDD = 4
4.6
6 V to 16 V
IDD
Supply current
VO = 2.5
25V
V,
No load
25°C
150
75
25°C
25
Full range
10
25°C
90
Full range
85
25°C
90
Full range
85
pA
pA
V
50
50
Full range
µV/mo
V
25°C
VO = 1 V to 4 V,,
RL = 500 kΩ
µV
µV/°C
0.5
25°C
UNIT
mV
315
V/mV
55
110
dB
110
25°C
1
Full range
dB
1.5
1.5
mA
∗On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2201M operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
VO = 0.5 V to 2.5 V,
RL = 10 kΩ,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
φm
Phase margin at unity gain
† Full range is – 55°C to 125°C.
TLC2201M
TA†
MIN
TYP
25°C
1.8
2.5
Full range
1.1
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
MAX
UNIT
V/µs
nV/√Hz
µV
25°C
0.6
fA/√Hz
f = 10 kHz,
CL = 100 pF
RL = 10 kΩ,
25°C
18
1.8
MHz
RL = 10 kΩ,
CL = 100 pF
25°C
45°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
31
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201M electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient of
input offset voltage
Input offset voltage
long-term drift (see Note 4)
MIN
25°C
VIC = 0,
IIB
Input bias current
VICR
Common mode input
Common-mode
voltage range
RS = 50 Ω
VOH
Maximum high-level
g
output
voltage
RL = 10 kΩ
VOL
Maximum low-level output
voltage
IO = 0
RS = 50 Ω
TYP
MAX
80
200
25°C
0.001
25°C
0.5
25°C
Full range
g
0
to
2.7
25°C
4.7
Full range
4.7
Full range
75
VO = 1 V to 4 V,,
RL = 10 kΩ
25°C
25
Full range
10
25°C
90
Full range
85
25°C
90
Full range
85
VDD = 4
4.6
6 V to 16 V
IDD
Supply current
VO = 2
2.5
5 V,
V
No load
0.005
0.001
25°C
Full range
0.005
0.5
500
1
4.8
500
4.7
315
4.8
0
50
25
pA
pA
V
315
75
55
µV/mo
V
50
150
µV
V
4.7
50
UNIT
µV/°C
05
0.5
50
150
Supplyy voltage
g rejection
j
ratio (∆VDD ± /∆VIO)
200
0
to
2.7
0
25°C
kSVR
80
500
25°C
VIC = VICRmin,
RS = 50 Ω
VO = 0,
MAX
400
1
Full range
Common-mode rejection
j
ratio
TYP
500
Full range
CMRR
MIN
05
0.5
Full range
VO = 1 V to 4 V,,
RL = 500 kΩ
TLC2210BM
400
Full range
Input offset current
Large-signal
g
g
differential
voltage amplification
TLC2201AM
Full range
IIO
AVD
TA†
TEST CONDITIONS
V/mV
55
10
110
90
110
dB
85
110
90
110
dB
85
1.1
1.5
1.5
1.1
1.5
1.5
mA
† Full range is – 55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observable through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
32
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201M operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
SR
Slew rate at unity gain
TEST CONDITIONS
TA†
VO = 0.5 V to 2.5 V,
RL = 10 kΩ,
kΩ
CL = 100 pF
TLC2201AM
MIN
TYP
25°C
1.8
2.5
Full range
1.1
TLC2201BM
MAX
MIN
TYP
1.8
2.5
MAX
UNIT
V/µs
1.1
Vn
Equivalent
q
input noise voltage
g
(see Note 5)
f = 10 Hz
25°C
18
35
18
30
f = 1 kHz
25°C
8
15
8
12
VN(PP)
Peak-to-peak equivalent
q
input
noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
25°C
0.6
0.6
fA/√Hz
25°C
1.8
1.8
MHz
25°C
45°
45°
Gain-bandwidth product
φm
Phase margin at unity gain
f = 10 kHz,
RL = 10 kΩ,,
CL = 100 pF
RL = 10 kΩ,
CL = 100 pF
nV/√Hz
µV
† Full range is – 55°C to 125°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
33
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202M electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless
otherwise noted)
PARAMETER
VIO
αVIO
TEST CONDITIONS
Temperature coefficient of input offset voltage
IIO
Input offset current
IIB
Input bias current
VICR
Common-mode input voltage
g range
g
VOM +
Maximum positive peak output voltage swing
RS = 50 Ω
VIC = 0
0,
TYP
MAX
100
1000
Full range
1250
Full range
0.001 0.005*
Full range
RS = 50 Ω
VIC = 0,
25°C
Maximum negative peak output voltage swing
Large signal differential voltage amplification
Large-signal
VO =1 V to 4 V,,
RL = 500 kΩ
VO = 1 V to 4 V,,
RL = 10 kΩ
CMRR
Common mode rejection ratio
Common-mode
VO = 0,,
RS = 50 Ω
VIC = VICRmin,,
kSVR
Supply voltage rejection ratio (∆VDD ± /∆VIO)
Supply-voltage
VDD= ± 2
2.3
3 V to ± 8 V
IDD
Supply current
VO = 0
0,
No load
µV/mo
pA
1
500
Full range
g
–5
to
2.7
25°C
4.7
Full range
µV
500
Full range
RS = 50 Ω
UNIT
µV/°C
0.5
25°C
RL = 10 kΩ
AVD
TLC2202M
MIN
25°C
Input offset voltage
Input offset voltage long-term drift (see Note 4)
VOM –
TA†
V
4.8
V
4.7
25°C
– 4.7
Full range
– 4.7
25°C
300
Full range
100
25°C
50
Full range
25
25°C
80
Full range
80
25°C
80
Full range
80
– 4.9
V
560
V/mV
100
115
dB
110
25°C
1.8
Full range
dB
2.7
2.7
mA
* On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2202M operating characteristics at specified free-air temperature, VDD ± = ±5 V
PARAMETER
TEST CONDITIONS
VO = ± 2.3 V,,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
φm
Phase margin at unity gain
† Full range is – 55°C to 125°C.
34
RL = 10 kΩ,,
TA†
TLC2202M
MIN
TYP
25°C
1.8
2.7
Full range
1.1
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
MHz
f = 10 kHz,,
CL = 100 pF
RL = 10 kΩ,,
25°C
19
1.9
RL = 10 kΩ,
CL = 100 pF
25°C
48°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202M electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless
otherwise noted)
PARAMETER
VIO
Input
In
ut offset voltage
αVIO
Temperature coefficient
of input offset voltage
TA†
TEST CONDITIONS
RS = 50 Ω
VICR
Common-mode
Common
mode input
voltage range
Maximum positive peak
VOM +
output voltage swing
VOM –
AVD
Maximum negative
peak
g
output voltage swing
Large-signal
differential
g
g
voltage amplification
Common-mode rejection
j
CMRR
ratio
kSVR
Supply-voltage
y
g rejection
j
ratio (∆VDD ± /∆VIO)
500
Full range
RS = 50 Ω
RL = 10 kΩ
VO = ± 4 V,
RL = 500 kΩ
VO = ± 4 V,
RL = 10 kΩ
MAX
80
500
0.001 0.005*
0.5
Full range
0.5
500
25°C
500
1
1
500
Full range
–5
to
2.7
25°C
4.7
Full range
4.7
25°C
– 4.7
Full range
– 4.7
25°C
300
Full range
100
25°C
50
Full range
25
VO = 0, VIC = VICRmin,
RS = 50 Ω
25°C
80
Full range
80
VDD ± = ± 2
2.3
3 V to ± 8 V
25°C
80
Full range
80
500
–5
to
2.7
4.8
4.7
– 4.7
4.8
– 4.9
– 4.7
560
300
50
µV/mo
pA
A
pA
A
V
V
560
100
100
µV
V
4.7
– 4.9
UNIT
µV/°C
05
0.5
0.001 0.005*
Full range
RS = 50 Ω
TYP
750
05
0.5
25°C
VIC = 0,
0
Input
In
ut bias current
80
MIN
750
25°C
Input
In
ut offset current
IIB
MAX
25°C
VIC = 0,
0
TLC2202BM
TYP
Full range
Input offset voltage
long-term drift (see Note 4)
IIO
TLC2202AM
MIN
100
V/mV
25
115
80
115
80
110
80
80
110
dB
dB
25°C
1.8
2.7
1.8
2.7
mA
Full range
2.7
2.7
* On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
IDD
Supply
Su
ly current
VO = 0
0,
No load
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
35
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202M operating characteristics at specified free-air temperature, VDD ± = ±5 V
PARAMETER
SR
Slew rate at unity gain
TLC2202AM
TEST CONDITIONS
TA†
MIN
TYP
VO = ± 2
2.3
3V
V,
RL = 10 kΩ,
kΩ
CL = 100 pF
25°C
18
1.8
27
2.7
Full range
1.1
TLC2202BM
MAX
MIN
TYP
18
1.8
27
2.7
MAX
UNIT
V/µs
1.1
Vn
Equivalent
q
input noise voltage
g
(see Note 5)
f = 10 Hz
25°C
18
35*
18
30*
f = 1 kHz
25°C
8
15*
8
12*
VN(PP)
Peak-to-peak equivalent
q
input
noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
25°C
0.6
0.6
fA/√Hz
MHz
φm
Gain-bandwidth product
f = 10 kHz,
RL = 10 kΩ,,
CL = 100 pF
25°C
1.9
1.9
Phase margin at unity gain
RL = 10 kΩ,
CL = 100 pF
25°C
48°
48°
nV/√Hz
µV
* On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
36
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202M electrical characteristics at specified free-air temperatures, VDD = 5 V (unless otherwise
noted)
PARAMETER
VIO
αVIO
TEST CONDITIONS
TLC2202M
MIN
TYP
MAX
100
1000
25°C
Input offset voltage
Temperature coefficient of input offset voltage
RS = 50 Ω
VIC = 0
0,
Input offset voltage long-term drift (see Note 4)
Full range
1250
Full range
Input offset current
IIB
Input bias current
VICR
Common-mode input voltage
g range
g
RS = 50 Ω
VOH
Maximum high-level
high level output voltage
RL = 10 kΩ
VOL
Maximum low-level
low level output voltage
IO = 0
0.001 0.005*
Full range
RS = 50 Ω
VIC = 0,
Large signal differential voltage amplification
Large-signal
25°C
500
Full range
g
0
to
2.7
25°C
4.7
Full range
4.7
V
4.8
25°C
CMRR
Common mode rejection ratio
Common-mode
VIC = VICRmin
min, RS = 50 Ω
kSVR
Supply voltage rejection ratio (∆VDD ± /∆VIO)
Supply-voltage
VDD = 4
4.6
6 V to 16 V
IDD
Supply current
VO = 2
2.5
5V
V,
No load
µV/mo
pA
1
0
Full range
VO = 1 V to 4 V,,
RL = 10 kΩ
µV
500
Full range
VO = 1 V to 4 V,,
RL = 500 kΩ
UNIT
µV/°C
0.5
25°C
IIO
AVD
TA†
V
50
50
25°C
150
Full range
75
25°C
25
Full range
10
25°C
75
Full range
75
25°C
80
Full range
80
mV
315
V/mV
55
110
dB
110
25°C
1.7
Full range
dB
2.6
2.6
mA
* On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2202M operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TEST CONDITIONS
VO = 0.5 V to 2.5 V,,
RL = 10 kΩ,
CL = 100 pF
SR
Slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
Gain bandwidth product
Gain-bandwidth
φm
Phase margin at unity gain
† Full range is – 55°C to 125°C.
TA†
TLC2202M
MIN
TYP
25°C
1.6
2.5
Full range
0.9
MAX
UNIT
V/µs
f = 10 Hz
25°C
18
f = 1 kHz
25°C
8
f = 0.1 to 1 Hz
25°C
0.5
f = 0.1 to 10 Hz
25°C
0.7
25°C
0.6
fA/√Hz
MHz
f = 10 kHz,,
CL = 100 pF
RL = 10 kΩ,,
25°C
19
1.9
RL = 10 kΩ,
CL = 100 pF
25°C
47°
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
nV/√Hz
µV
37
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202M electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient of
input offset voltage
TA†
TEST CONDITIONS
25°C
RS = 50 Ω
VIC = 0
0,
Full range
TYP
MAX
80
500
RS = 50 Ω
IIB
Input bias current
VICR
Common-mode
Common
mode input
voltage range
RS = 50 Ω
VOH
Maximum high-level
g
output
voltage
RL = 10 kΩ
VOL
Maximum low-level output
voltage
IO = 0
AVD
Large-signal
g
g
differential
voltage amplification
kSVR
Supply-voltage
y
g rejection
j
ratio (∆VDD ± /∆VIO)
VDD = 4
4.6
6 V to 16 V
IDD
Supply current
VO = 2.5
2 5 V,
V
No load
80
500
25°C
0.5
500
1
1
500
Full range
g
0
to
2.7
25°C
4.7
Full range
4.7
500
0
to
2.7
4.8
4.7
50
4.8
0
50
25°C
150
Full range
75
25°C
25
Full range
10
25°C
75
Full range
75
25°C
80
Full range
80
25°C
Full range
315
50
25
pA
pA
mV
315
75
55
µV/mo
V
50
150
µV
V
4.7
0
UNIT
µV/°C
0.001 0.005*
500
25°C
VO = 0,, VIC = VICRmin,,
RS = 50 Ω
MAX
05
0.5
0.5
Full range
Full range
VO = 1 V to 4 V,,
RL = 10 kΩ
TYP
750
0.001 0.005*
Full range
VO = 1 V to 4 V,,
RL = 500 kΩ
MIN
05
0.5
25°C
VIC = 0
0,
TLC2202BM
750
25°C
Input offset current
Common-mode rejection
j
CMRR
ratio
MIN
Full range
Input offset voltage
long-term drift (see Note 4)
IIO
TLC2202AM
V/mV
55
10
110
75
110
dB
75
110
80
110
dB
80
1.7
2.6
2.6
1.7
2.6
2.6
mA
* On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
38
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202M operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
SR
Slew rate at unity gain
TLC2202AM
TEST CONDITIONS
TA†
MIN
TYP
VO = 0
0.5
5 V to 2
2.5
5V
V,
RL = 10 kΩ,
kΩ
CL = 100 pF
25°C
16
1.6
25
2.5
Full range
0.9
TLC2202BM
MAX
MIN
TYP
16
1.6
25
2.5
MAX
V/µs
1.1
Vn
Equivalent
q
input noise voltage
g
(see Note 5)
f = 10 Hz
25°C
18
35*
18
30*
f = 1 kHz
25°C
8
15*
8
12*
VN(PP)
Peak-to-peak equivalent
q
input
noise voltage
f = 0.1 to 1 Hz
25°C
0.5
0.5
f = 0.1 to 10 Hz
25°C
0.7
0.7
In
Equivalent input noise current
φm
UNIT
nV/√Hz
µV
25°C
0.6
0.6
fA/√Hz
Gain-bandwidth product
f = 10 kHz,,
RL = 10 kΩ,
CL = 100 pF
25°C
1.9
1.9
MHz
Phase margin at unity gain
RL = 10 kΩ,
CL = 100 pF
25°C
47°
47°
* On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
† Full range is – 55°C to 125°C
NOTE 5: This parameter is tested on a sample basis for the TLC2202A and on all devices for the TLC2202B. For other test requirements, please
contact the factory. This statement has no bearing on testing or nontesting of other parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
39
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2201Y electrical characteristics at VDD ± = ±5 V, TA = 25°C (unless otherwise noted)
PARAMETER
VIO
TEST CONDITIONS
TLC2201Y
MIN
Input offset voltage
TYP
MAX
µV
100
Input offset voltage long-term drift (see Note 4)
VIC = 0,
0
IIO
IIB
Input offset current
VOH
VOL
Maximum high-level output voltage
RL = 10 kΩ
Maximum low-level output voltage
IO = 0
VO = 1 V to 4 V,
Input bias current
AVD
Large signal differential voltage amplification
Large-signal
CMRR
Common-mode rejection ratio
VO = 1 V to 4 V,
VIC = VICRmin,
RS = 50 Ω
µV/mo
0.001
RS = 50 Ω
0.5
pA
1
pA
4.8
V
0
RL = 500 Ω
55
RL = 10 Ω
55
VO = 0,
UNIT
mV
V/mV
110
dB
Supply voltage rejection ratio (∆VDD ± /∆VIO)
VDD = 4.6 to 16 V
110
dB
IDD
Supply current per amplifier
VO = 2.5 V,
No load
1
mA
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
kSVR
TLC2201Y operating characteristics at VDD ± = ± 5 V, TA = 25°C
PARAMETER
SR
Positive slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak-to-peak equivalent
q
input noise
voltage
In
Equivalent input noise current
φm
40
TLC2201Y
TEST CONDITIONS
VO = ± 0.5 to 2.5 V,
f = 10 Hz
RL = 10 kΩ,
MIN
CL = 100 pF
TYP
2.5
UNIT
V/µs
18
f = 1 kHz
8
f = 0.1 to 1 Hz
0.5
f = 0.1 to 10 Hz
0.7
Gain-bandwidth product
f = 10 kHz,
RL = 10 kΩ,
Phase margin at unity gain
RL = 10 kΩ,
CL = 100 pF
POST OFFICE BOX 655303
MAX
• DALLAS, TEXAS 75265
CL = 100 pF
nV/√Hz
µV
0.6
pA/√Hz
1.8
MHz
48°
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TLC2202Y electrical characteristics, VDD = 5 V, TA = 25°C (unless otherwise noted)
PARAMETER
VIO
TEST CONDITIONS
TLC2202Y
MIN
Input offset voltage
TYP
MAX
µV
100
Input offset voltage long-term drift (see Note 4)
Input offset current
VOH
VOL
Maximum high-level output voltage
RL = 10 kΩ
Maximum low-level output voltage
IO = 0
VO = 1 V to 4 V,
Input bias current
AVD
Large signal differential voltage amplification
Large-signal
CMRR
Common-mode rejection ratio
kSVR
Supply-voltage rejection ratio (∆VDCC /∆VIO)
VO = 1 V to 4 V,
VO = 0, VICRmin,
µV/mo
0.001
RS = 50 Ω
VIC = 0
0,
IIO
IIB
UNIT
0.5
pA
1
pA
4.8
V
0
mV
RL = 500 Ω
315
RL = 10 Ω
55
RS = 50 Ω
110
dB
110
dB
VDD = 4.6 to 16 V
VO = 2.5 V,
V/mV
IDD
Supply current
No load
1.7
mA
NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLC2202Y operating characteristics at VDD = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
VO = 0.5 V to 2.5 V,
CL = 100 pF
f = 10 Hz
SR
Positive slew rate at unity gain
Vn
Equivalent input noise voltage
VN(PP)
Peak to peak equivalent input noise voltage
Peak-to-peak
In
Equivalent input noise current
B1
Gain-bandwidth product
f = 10 kHz,
CL = 100 pF
φm
Phase margin at unity gain
RL = 10 kΩ,
RL = 10 kΩ,
TLC2202Y
MIN
TYP
2.5
UNIT
V/µs
18
f = 10 kHz
8
f = 0.1 to 1 Hz
0.5
f = 0.1 to 10 Hz
0.7
POST OFFICE BOX 655303
MAX
nV/√Hz
µV
0.6
pA/√Hz
RL = 10 kΩ,
1.9
MHz
CL = 100 pF
47°
• DALLAS, TEXAS 75265
41
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
PARAMETER MEASUREMENT INFORMATION
10 kΩ
VDD +
2 kΩ
VI
VDD +
–
+
VO
VDD –
VO
CL
(see Note A)
VDD – /GND
20 Ω
20 Ω
–
+
100 Ω
RL
NOTE A: CL includes fixture capacitance.
Figure 1. Noise-Voltage Test Circuit
Figure 2. Phase-Margin Test Circuit
VDD +
VI
–
+
VO
Ground Shield
VDD –
CL
(see Note A)
VDD +
–
+
RL
VO
VDD – /GND
pA
pA
NOTE A: CL includes fixture capacitance.
Figure 3. Slew-Rate Test Circuit
Figure 4. Input-Bias and Offset-Current Test Circuit
typical values
Typical values presented in this data sheet represent the median (50% point) of device parametric performance.
input bias and offset current
At the picoamp bias current level of the TLC220x, TLC220xA, and TLC220xB, accurate measurement of the
bias current becomes difficult. Not only does this measurement require a picoammeter, but test socket leakages
can easily exceed the actual device bias currents. To measure these small currents, Texas Instruments uses
a two-step process. The socket leakage is measured using picoammeters with bias voltages applied but with
no device in the socket. The device is then inserted in the socket, and a second test measuring both the socket
leakage and the device input bias current is performed. The two measurements are then subtracted
algebraically to determine the bias current of the device.
noise
Texas Instruments offers automated production noise testing to meet individual application requirements. Noise
voltage at f = 10 Hz and f = 1 kHz is 100% tested on every TLC2201B device, while lot sample testing is
performed on the TLC220xA. For other noise requirements, please contact the factory.
42
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
Input offset voltage
Distribution
IIB
Input bias current
vs Common-mode input voltage
g
vs Free-air temperature
7
8
VOM
Maximum peak output voltage
vs Output current
vs Free-air temperature
9
10
VO(PP)
Maximum peak-to-peak output voltage
vs Frequency
11
VOH
High-level
g
output voltage
g
vs Frequency
q
y
vs High-level
g
output current
vs Free-air temperature
12
13
14
VOL
Low level output voltage
Low-level
vs Low-level output current
vs Free-air temperature
15
16
AVD
Large signal differential voltage amplification
Large-signal
vs Frequency
q
y
vs Free-air temperature
17
18
IOS
Short circuit output current
Short-circuit
vs Supply
y voltage
g
vs Free-air temperature
19
20
CMRR
Common-mode rejection ratio
vs Frequency
21
IDD
Supply current
vs Supply
y voltage
g
vs Free-air temperature
22
23, 24
Pulse response
Small signal
g
Large signal
25,, 26
27, 28
Slew rate
vs Supply
y voltage
g
vs Free-air temperature
29
30
Noise voltage (referred to input)
0.1 to 1 Hz
0.1 to 10 Hz
31
32
Gain bandwidth product
Gain-bandwidth
vs Supply
y voltage
g
vs Free-air temperature
33,, 34
35
Phase margin
vs Supply
y voltage
g
vs Free-air temperature
36,, 37
38, 39
Phase shift
vs Frequency
SR
φm
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5, 6
17
43
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TYPICAL CHARACTERISTICS
TLC2202
DISTRIBUTION OF
INPUT OFFSET VOLTAGE
DISTRIBUTION OF TLC2201
INPUT OFFSET VOLTAGE
16
20
1726 Amplifiers Tested From 1 Wafer Lot
VDD ± = ± 15 V
TA = 25°C
P Package
14
Percentage of Units – %
Percentage of Units – %
16
408 Units Tested From 2 Wafer Lots
VDD ± = ± 5 V
TA = 25°C
P Package
12
8
12
10
8
6
4
4
2
0
– 500
– 300
300
100
– 100
0
–1000
500
– 600
– 200
300
VDD ± = ± 5 V
TA = 25°C
VDD ± = ± 5 V
VO = 0
VIC = 0
250
6
I IB – Input Bias Current – pA
IIIB
IB – Input Bias Current – pA
1000
INPUT BIAS CURRENT†
vs
FREE-AIR TEMPERATURE
INPUT BIAS CURRENT
vs
COMMON-MODE INPUT VOLTAGE
8
600
Figure 6
Figure 5
10
200
VIO – Input Offset Voltage – µV
VIO – Input Offset Voltage – µV
4
2
0
–2
–4
–6
200
150
100
50
–8
– 10
–5
0
–4
–3
–2
–1
0
1
2
3
4
5
25
45
65
85
105
TA – Free-Air Temperature – °C
VIC – Common-Mode Input Voltage – V
Figure 7
Figure 8
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
44
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
125
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TYPICAL CHARACTERISTICS
MAXIMUM PEAK OUTPUT VOLTAGE†
vs
FREE-AIR TEMPERATURE
MAXIMUM PEAK OUTPUT VOLTAGE
vs
OUTPUT CURRENT
6
VDD ± = ± 5 V
TA = 25°C
VOM +
VOM
V OM – Maximum Peak Output Voltage – V
|VOM | – Maximum Peak Output Voltage – V
VOM
5
4
VOM –
3
2
1
0
0
2
4
8
6
VOM +
4
2
VDD ± = ± 5 V
RL = 10 kΩ
0
–2
–4
VOM –
–6
– 75
10
– 50
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
|IO| – Output Current – mA
Figure 9
Figure 10
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE†
vs
FREQUENCY
HIGH-LEVEL OUTPUT VOLTAGE†
vs
FREQUENCY
10
5
VOH – High-Level Output Voltage – V
V0H
VO(PP) – Maximum Peak-to-Peak Output Voltage – V
125
8
TA = – 55°C
6
TA = 125°C
4
2
VDD ± = ± 5 V
RL = 10 kΩ
0
10 k
30 k
100 k
300 k
1M
4
TA = – 55°C
3
TA = 125°C
2
1
VDD = 5 V
RL = 10 kΩ
0
10 k
f – Frequency – Hz
30 k
100 k
300 k
1M
f – Frequency – Hz
Figure 11
Figure 12
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
45
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TYPICAL CHARACTERISTICS
HIGH-LEVEL OUTPUT VOLTAGE†
vs
FREE-AIR TEMPERATURE
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
VDD
6
VDD = 5 V
RL = 10 kΩ
VDD – 2
V OH – High-Level Output Voltage – V
VOM
V OH – High-Level Output Voltage – V
VOM
TA = 25°C
VDD = 5 V
VDD – 4
VDD – 6
VDD = 10 V
VDD – 8
VDD – 10
VDD – 12
VDD = 16 V
VDD – 14
VDD – 16
0
1
2
3
4
5
4
3
2
1
0
– 75
5
– 50
IOH – High-Level Output Current – mA
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 13
Figure 14
LOW-LEVEL OUTPUT VOLTAGE†
vs
FREE-AIR TEMPERATURE
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
1.5
2
VDD = 5 V
VDD = 5 V
VDD = 10 V
VOL
VOL – Low-Level Output Voltage – V
TA = 25°C
VOL
VOL – Low-Level Output Voltage – V
125
VDD = 16 V
1.5
1
0.5
IOL = 5 mA
1
0.5
IOL = 1 mA
0
0
2
4
6
8
IOL – Low-Level Output Current – mA
10
0
– 75
– 50
Figure 15
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 16
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
46
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
125
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TYPICAL CHARACTERISTICS
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION†
vs
FREE-AIR TEMPERATURE
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT
vs
FREQUENCY
50°
80
70°
60
90°
Phase Shift
40
110°
20
130°
150°
0
– 20
10
100
1k
10 k
100 k
AVD
A
VD – Large-Signal Differential
Voltage Amplification – dB
AVD
Phase Shift
AVD
AVD – Large-Signal Differential
Voltage Amplification – dB
VDD ± = ± 5 V
RL = 10 kΩ
CL = 100 pF
TA = 25°C
100
ÁÁ
ÁÁ
130
30°
120
ÁÁ
ÁÁ
ÁÁ
VDD ± = ± 5 V, RL = 500 kΩ
120
110
VDD = 5 V, RL = 500 kΩ
VDD ± = ± 5 V, RL = 10 kΩ
100
VDD = 5 V, RL = 10 kΩ
90
80
– 75
170°
1M
– 50
f – Frequency – Hz
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 18
Figure 17
SHORT-CIRCUIT OUTPUT CURRENT†
vs
FREE-AIR TEMPERATURE
SHORT-CIRCUIT OUTPUT CURRENT
vs
SUPPLY VOLTAGE
15
VO = 0
TA= 25°C
IIOS
OS – Short-Circuit Output Current – mA
IIOS
OS – Short-Circuit Output Current – mA
12
8
4
VID = – 100 mV
0
–4
–8
VID = 100 mV
– 12
0
1
125
2
3
4
5
6
|VDD ±| – Supply Voltage – V
7
8
VDD ± = ± 5 V
VO = 0
10
5
VID = – 100 mV
0
–5
VID = 100 mV
– 10
– 15
– 75
– 50
Figure 19
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
125
Figure 20
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
47
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TYPICAL CHARACTERISTICS
SUPPLY CURRENT†
vs
SUPPLY VOLTAGE
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
2.5
VO = 0
No Load
TA = 25°C
100
2
IDD
I DD – Supply Current – mA
CMRR – Common-Mode Rejection Ratio – dB
120
VDD ± = ± 5 V
80
60
VDD = 5 V
40
1.5
1
0.5
20
0
0
10
100
1k
100 k
10 k
1M
0
1
2
3
4
5
6
7
8
|VDD ±| – Supply Voltage – V
f – Frequency – Hz
Figure 21
Figure 22
TLC2201
SUPPLY CURRENT†
vs
FREE-AIR TEMPERATURE
TLC2202
SUPPLY CURRENT†
vs
FREE-AIR TEMPERATURE
1.2
2.5
VDD ± = ± 5 V
VO = VDD + /2
No Load
1
2
IIDD
DD – Supply Current – mA
IIDD
DD – Supply Current – mA
TA = 125°C
TA = 25°C
TA = – 55°C
VDD = 5 V
0.8
0.6
0.4
VDD ± = ± 5 V
VDD = 5 V
1.5
1
0.5
0.2
VO = VDD + / 2
No Load
0
– 75
– 50
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
125
0
– 75
– 50
Figure 23
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 24
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
48
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
125
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TYPICAL CHARACTERISTICS
VOLTAGE-FOLLOWER
SMALL-SIGNAL
PULSE RESPONSE
VOLTAGE-FOLLOWER
SMALL-SIGNAL
PULSE RESPONSE
VO – Output Voltage – mV
VO
75
50
160
VDD ± = ± 5 V
RL = 10 kΩ
CL = 100 pF
TA = 25°C
140
VO – Output Voltage – mV
VO
100
25
0
– 25
– 50
–75
120
VDD = 5 V
RL = 10 kΩ
CL = 100 pF
TA = 25°C
100
80
60
40
20
0
– 20
–100
0
1
2
3
4
5
6
7
0
t – Time – µs
Figure 25
1
2
3
4
t – Time – µs
5
VDD = 5 V
RL = 10 kΩ
CL = 100 pF
TA = 25°C
4
4
VO – Output Voltage – V
VO
3
VO – Output Voltage – V
VO
7
VOLTAGE-FOLLOWER
LARGE-SIGNAL
PULSE RESPONSE
5
2
1
0
–1
–2
VDD ± = ± 5 V
RL = 10 kΩ
CL = 100 pF
TA = 25°C
–4
6
Figure 26
VOLTAGE-FOLLOWER
LARGE-SIGNAL
PULSE RESPONSE
–3
5
3
2
1
0
–1
–5
0
5
10
15
20
25
30
35
40
0
t – Time – µs
5
10
15
20
25
30
35
40
t – Time – µs
Figure 27
Figure 28
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
49
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TYPICAL CHARACTERISTICS
SLEW RATE†
vs
FREE-AIR TEMPERATURE
SLEW RATE
vs
SUPPLY VOLTAGE
4
4
SR –
RL = 10 kΩ
CL = 100 pF
TA = 25°C
SR –
3
SR – Slew Rate – V/µ s
SR – Slew Rate – V/µ s
3
SR +
2
SR +
2
1
1
0
– 75
0
0
1
2
3
4
5
6
7
8
VDD ± = ± 5 V
RL = 10 kΩ
CL = 100 pF
– 50
|VDD ±| – Supply Voltage – V
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
Figure 29
Figure 30
NOISE VOLTAGE
(REFERRED TO INPUT)
OVER A 10-SECOND INTERVAL
NOISE VOLTAGE
(REFERRED TO INPUT)
OVER A 10-SECOND INTERVAL
1
1
VDD ± = ± 5 V
f = 0.1 Hz to 1 Hz
TA= 25°C
0.75
125
VDD ± = ± 5 V
f = 0.1 Hz to 10 Hz
TA= 25°C
0.8
0.6
0.4
V
Noise Voltage – µ
uV
V
Noise Voltage – µ
uV
0.5
0.25
0
– 0.25
0.2
0
– 0.2
– 0.4
– 0.5
– 0.6
– 0.75
–1
0
– 0.8
1
2
3
4
5
6
7
8
9
10
–1
0
1
t – Time – s
2
3
4
5
6
7
8
9
t – Time – s
Figure 31
Figure 32
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
50
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
10
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TYPICAL CHARACTERISTICS
TLC2201
GAIN-BANDWIDTH PRODUCT
vs
SUPPLY VOLTAGE
TLC2202
GAIN-BANDWIDTH PRODUCT
vs
SUPPLY VOLTAGE
2.1
RL = 10 kΩ
CL = 100 pF
TA = 25°C
Gain-Bandwidth Product – MHz
Gain-Bandwidth Product – MHz
2.1
2
1.9
1.8
0
1
6
2
3
4
5
|VDD ±| – Supply Voltage – V
7
f = 10 kHz
RL = 10 kΩ
CL = 100 pF
TA = 25°C
2
1.9
1.8
8
0
1
2
3
4
5
6
|VDD ±| – Supply Voltage – V
8
Figure 34
Figure 33
TLC2201
PHASE MARGIN
vs
SUPPLY VOLTAGE
GAIN-BANDWIDTH PRODUCT†
vs
FREE-AIR TEMPERATURE
2.5
50°
f = 10 kHz
RL = 10 kΩ
CL = 100 pF
RL = 10 kΩ
CL = 100 pF
TA = 25°C
48°
VDD ± = ± 5 V
2
φm – Phase Margin
om
Gain-Bandwidth Product – MHz
7
VDD = 5 V
1.5
46°
44°
42°
1
– 75
40°
– 50
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
125
0
1
2
3
4
5
6
|VDD ±| – Supply Voltage – V
7
8
Figure 36
Figure 35
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
51
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
TYPICAL CHARACTERISTICS
TLC2202
PHASE MARGIN
vs
SUPPLY VOLTAGE
50°
TLC2201
PHASE MARGIN†
vs
FREE-AIR TEMPERATURE
50°
RL = 10 kΩ
CL = 100 pF
TA = 25°C
VDD ± = ± 5 V
48°
φm – Phase Margin
om
φom
m – Phase Margin
48°
46°
44°
42°
46°
VDD = 5 V
44°
42°
RL = 10 kΩ
CL = 100 pF
40°
0
1
2
3
4
5
6
|VDD ±| – Supply Voltage – V
7
40°
– 75
8
– 50
– 25
0
25
50
75
100
125
TA – Free-Air Temperature – °C
Figure 37
Figure 38
TLC2202
PHASE MARGIN†
vs
FREE-AIR TEMPERATURE
50°
VDD ± = ± 5 V
φom
m – Phase Margin
48°
VDD = 5 V
46°
44°
42°
RL = 10 kΩ
CL = 100 pF
40°
– 75
– 50
– 25
0
25
50
75
100
125
TA – Free-Air Temperature – °C
Figure 39
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
52
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
APPLICATION INFORMATION
latch-up avoidance
Because CMOS devices are susceptible to latch-up due to their inherent parasitic thyristors, the TLC220x,
TLC220xA, and TLC220xB inputs and outputs are designed to withstand – 100-mA surge currents without
sustaining latch-up; however, techniques reducing the chance of latch-up should be used whenever possible.
Internal protection diodes should not be forward biased in normal operation. Applied input and output voltages
should not exceed the supply voltage by more than 300 mV. Care should be exercised when using capacitive
coupling on pulse generators. Supply transients should be shunted by the use of decoupling capacitors
(0.1 µF typical) located across the supply rails as close to the device as possible.
electrostatic discharge protection
These devices use internal ESD-protection circuits that prevent functional failures at voltages at or below
2000 V. Care should be exercised in handling these devices as exposure to ESD may result in degradation of
the device parametric performance.
macromodel information
Macromodel information provided was derived using Microsim Parts , the model generation software used
with Microsim PSpice . The Boyle macromodel (see Note 5) and subcircuit in Figure 40 were generated using
the TLC220x typical electrical and operating characteristics at 25°C. Using this information, output simulations
of the following key parameters can be generated to a tolerance of 20% (in most cases):
D Maximum positive output voltage swing
D Unity-gain frequency
D Maximum negative output voltage swing
D Common-mode rejection ratio
D Slew rate
D Phase margin
D Quiescent power dissipation
D DC output resistance
D Input bias current
D AC output resistance
D Open-loop voltage amplification
D Short-circuit output current limit
NOTE 5: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”, IEEE Journal
of Solid-State Circuits, SC-9, 353 (1974).
PSpice and Parts are trademarks of MicroSim Corporation.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
53
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
APPLICATION INFORMATION
macromodel information (continued)
99
3
VCC +
egnd
9
rss
92
fb
–
+
iss
din
+
rp
2
10
IN –
j1
dp
vc
j2
IN+
1
11
r2
–
53
C2
6
dc
12
hlim
–
+
VCC –
54
4
+
–
–
+
vin
+
gcm
ga
–
ro1
de
5
–
ve
OUT
.subckt TLC220x 1 2 3 4 5
*
c1
11 12 8.51E–12
c2
6
7 50.00E–12
cpsr 85 86 79.6E–9
dcm+ 81 82 dx
dcm– 83 81 dx
dc
5
53 dx
de
54 5 dx
dlp 90 91 dx
dln 92 90 dx
dp
4
3 dx
ecmr 84 99 (2,99) 1
egnd 99 0 poly(2) (3,0) (4,0) 0 .5 .5
epsr 85 0 poly(1) (3,4) –200E–6 20E–6
ense 89 2 poly(1) (88,0) 100E–6 1
fb
7
99 poly(6) vb vc ve vlp vln
+ vpsr 0 +
895.9E3 –90E3 90E3 90E3 –90E3 895E3
ga
6
0 11 12 314.2E–6
gcm 0
6 10 99 1.295E–9
gpsr 85 86 (85,86) 100E–6
grd1 60 11 (60,11) 3.141E–4
grd2 60 12 (60,12) 3.141E–4
hlim 90 0 vlim 1k
hcmr 80 1 poly(2) vcm+ vcm– 0 1E2 1E2
irp 3
4 965E–6
iss 3
10 dc 135.0E–6
iio 2
0 .5E–12
i1
88 0 1E–21
j1
11 89 10 jx
j2
12 80 10 jx
r2
6
9 100.0E3
rcm 84 81 1k
rn1 88 0 1500
ro1 8
5 188
ro2 7
99 187
rss 10 99 1.481E6
vad 60 4 –.3v
vcm+ 82 99 2.2
vcm– 83 99 –4.5
vb
9
0 dc 0
vc
3
53 dc .9
ve
54 4 dc .8
vlim 7
8 dc 0
vlp 91 0 dc 2.8
vln 0
92 dc 2.8
vpsr 0
86 dc 0
.model dx d(is=800.0E–18)
.model jx pjf(is=500.0E–15 beta=1.462E–3
+ vto=–.155 kf=1E–17)
.endsx
Figure 40. Boyle Macromodel and Subcircuit
54
–
vlim
8
rd2
91
+
vip
7
C1
rd1
+ dip
90
ro2
vb
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
MECHANICAL INFORMATION
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
PINS **
0.050 (1,27)
8
14
16
A MAX
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MIN
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
DIM
0.020 (0,51)
0.014 (0,35)
14
0.010 (0,25) M
8
0.244 (6,20)
0.228 (5,80)
0.008 (0,20) NOM
0.157 (4,00)
0.150 (3,81)
1
Gage Plane
7
A
0.010 (0,25)
0°– 8°
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
0.004 (0,10)
4040047 / B 03/95
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
Four center pins are connected to die mount pad.
Falls within JEDEC MS-012
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
55
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
MECHANICAL INFORMATION
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
28 TERMINAL SHOWN
18
17
16
15
14
13
NO. OF
TERMINALS
**
12
19
11
20
10
A
B
MIN
MAX
MIN
MAX
20
0.342
(8,69)
0.358
(9,09)
0.307
(7,80)
0.358
(9,09)
28
0.442
(11,23)
0.458
(11,63)
0.406
(10,31)
0.458
(11,63)
21
9
22
8
44
0.640
(16,26)
0.660
(16,76)
0.495
(12,58)
0.560
(14,22)
23
7
52
0.739
(18,78)
0.761
(19,32)
0.495
(12,58)
0.560
(14,22)
24
6
68
25
5
0.938
(23,83)
0.962
(24,43)
0.850
(21,6)
0.858
(21,8)
84
1.141
(28,99)
1.165
(29,59)
1.047
(26,6)
1.063
(27,0)
B SQ
A SQ
26
27
28
1
2
3
4
0.080 (2,03)
0.064 (1,63)
0.020 (0,51)
0.010 (0,25)
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.045 (1,14)
0.035 (0,89)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
4040140 / D 10/96
NOTES: A.
B.
C.
D.
E.
56
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a metal lid.
The terminals are gold plated.
Falls within JEDEC MS-004
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
MECHANICAL INFORMATION
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE PACKAGE
0.400 (10,20)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.130 (3,30) MIN
0.063 (1,60)
0.015 (0,38)
0°–15°
0.023 (0,58)
0.015 (0,38)
0.015 (0,38)
0.008 (0,20)
0.100 (2,54)
4040107 / B 04/95
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a ceramic lid using glass frit.
Index point is provided on cap for terminal identification only on press ceramic glass frit seal only
Falls within MIL-STD-1835 GDIP1-T8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
57
TLC220x, TLC220xA, TLC220xB, TLC220xY
Advanced LinCMOS LOW-NOISE PRECISION
OPERATIONAL AMPLIFIERS
SLOS175 – FEBRUARY 1997
MECHANICAL INFORMATION
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE PACKAGE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0°– 15°
0.010 (0,25) M
0.010 (0,25) NOM
4040082 / B 03/95
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
58
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
9-Oct-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
5962-9088201M2A
ACTIVE
LCCC
FK
20
1
TBD
5962-9088201MPA
ACTIVE
CDIP
JG
8
1
TBD
Lead/Ball Finish
MSL Peak Temp (3)
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
5962-9088203Q2A
ACTIVE
LCCC
FK
20
1
TBD
5962-9088203QPA
ACTIVE
CDIP
JG
8
1
TBD
POST-PLATE N / A for Pkg Type
A42 SNPB
TLC2201ACD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201ACDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201ACDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201ACDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201ACP
OBSOLETE
PDIP
P
8
TBD
Call TI
TLC2201AID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201AIDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201AIDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201AIDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201AIP
OBSOLETE
PDIP
P
8
TBD
Call TI
N / A for Pkg Type
Call TI
Call TI
TLC2201AMD
ACTIVE
SOIC
D
8
75
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLC2201AMDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201AMFKB
ACTIVE
LCCC
FK
20
1
TBD
TLC2201AMJG
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TLC2201AMJGB
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TLC2201AMP
OBSOLETE
PDIP
P
8
TBD
Call TI
Call TI
POST-PLATE N / A for Pkg Type
TLC2201BCD
OBSOLETE
SOIC
D
8
TBD
Call TI
Call TI
TLC2201BCDR
OBSOLETE
SOIC
D
8
TBD
Call TI
Call TI
TLC2201BCP
OBSOLETE
PDIP
P
8
TBD
Call TI
Call TI
TLC2201BID
OBSOLETE
SOIC
D
8
TBD
Call TI
Call TI
TLC2201BIDR
OBSOLETE
SOIC
D
8
TBD
Call TI
Call TI
TLC2201BIP
OBSOLETE
PDIP
P
8
TBD
Call TI
Call TI
TLC2201BMP
OBSOLETE
PDIP
P
8
TBD
Call TI
Call TI
TLC2201CD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201CDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201CDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201CDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201CP
ACTIVE
PDIP
P
8
CU NIPDAU
N / A for Pkg Type
50
Addendum-Page 1
Pb-Free
(RoHS)
PACKAGE OPTION ADDENDUM
www.ti.com
9-Oct-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLC2201CPE4
ACTIVE
PDIP
P
8
TLC2201CPSR
OBSOLETE
SO
PS
8
TLC2201ID
ACTIVE
SOIC
D
TLC2201IDG4
ACTIVE
SOIC
TLC2201IDR
ACTIVE
TLC2201IDRG4
Lead/Ball Finish
CU NIPDAU
MSL Peak Temp (3)
50
Pb-Free
(RoHS)
N / A for Pkg Type
TBD
Call TI
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC2201IP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLC2201IPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TLC2201MFKB
ACTIVE
LCCC
FK
20
1
TBD
Call TI
POST-PLATE N / A for Pkg Type
TLC2201MJG
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TLC2201MJGB
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TLC2202ACD
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
Call TI
Level-1-260C-UNLIM
TLC2202ACDG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
Call TI
Level-1-260C-UNLIM
TLC2202ACDR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
Call TI
Level-1-260C-UNLIM
TLC2202ACDRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
Call TI
Level-1-260C-UNLIM
TLC2202ACP
OBSOLETE
PDIP
P
8
TBD
Call TI
Call TI
TLC2202AID
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
Call TI
Level-1-260C-UNLIM
TLC2202AIDG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
Call TI
Level-1-260C-UNLIM
TLC2202AIP
OBSOLETE
PDIP
P
8
TBD
Call TI
Call TI
TLC2202BCD
OBSOLETE
SOIC
D
14
TBD
Call TI
Call TI
TLC2202BCDR
OBSOLETE
SOIC
D
14
TBD
Call TI
Call TI
TLC2202BCP
OBSOLETE
PDIP
P
8
TBD
Call TI
Call TI
TLC2202BID
OBSOLETE
SOIC
D
14
TBD
Call TI
Call TI
TLC2202BIDR
OBSOLETE
SOIC
D
14
TBD
Call TI
Call TI
TLC2202BIP
OBSOLETE
PDIP
P
8
TBD
Call TI
Call TI
TLC2202BMD
OBSOLETE
SOIC
D
8
TBD
Call TI
Call TI
TLC2202BMP
OBSOLETE
PDIP
P
8
TBD
Call TI
Call TI
TLC2202CD
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
Call TI
Level-1-260C-UNLIM
TLC2202CDG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
Call TI
Level-1-260C-UNLIM
TLC2202CDR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
Call TI
Level-1-260C-UNLIM
TLC2202CDRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
Call TI
Level-1-260C-UNLIM
TLC2202CP
ACTIVE
PDIP
P
8
50
Addendum-Page 2
Pb-Free
CU NIPDAU
N / A for Pkg Type
PACKAGE OPTION ADDENDUM
www.ti.com
9-Oct-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLC2202CPE4
ACTIVE
PDIP
P
8
TLC2202CPSR
ACTIVE
SO
PS
8
TLC2202CPSRG4
ACTIVE
SO
PS
8
TLC2202ID
ACTIVE
SOIC
D
14
50
TLC2202IDG4
ACTIVE
SOIC
D
14
TLC2202IP
ACTIVE
PDIP
P
TLC2202IPE4
ACTIVE
PDIP
P
Lead/Ball Finish
MSL Peak Temp (3)
(RoHS)
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TLC2201ACDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLC2201AIDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLC2201CDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLC2201IDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLC2202ACDR
SOIC
D
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
TLC2202CDR
SOIC
D
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
TLC2202CPSR
SO
PS
8
2000
330.0
16.4
8.2
6.6
2.5
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TLC2201ACDR
SOIC
D
8
2500
346.0
346.0
29.0
TLC2201AIDR
SOIC
D
8
2500
346.0
346.0
29.0
TLC2201CDR
SOIC
D
8
2500
346.0
346.0
29.0
TLC2201IDR
SOIC
D
8
2500
346.0
346.0
29.0
TLC2202ACDR
SOIC
D
14
2500
346.0
346.0
33.0
TLC2202CDR
SOIC
D
14
2500
346.0
346.0
33.0
TLC2202CPSR
SO
PS
8
2000
346.0
346.0
33.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated