TS9004 Series 300mA CMOS LDO Adjustable Voltage with Enable & Power Good SOT-26 Pin Definition: 1. Input 2. Ground 3. Enable 4. Power Good 5. Adjustable 6. Output SOT-25 Pin Definition: 1. Input 2. Ground 3. Enable 4. Adjustable 5. Output General Description The TS9004 is a positive voltage linear regulator developed utilizing CMOS technology featured low quiescent current (35uA typ.), low dropout voltage, and high output voltage accuracy, making them ideal for battery applications. The Chip Enable (CE) includes a CMOS or TTL compatible input allows the output to be turned off to prolong battery life. The TS9004 is included a precision voltage reference, current fold-back, error correction circuit, a current limited output driver, over temperature shutdown, and a “Power Good” detector, which pulls low when the output is out of regulation. Features ● ● ● ● ● ● ● ● Ordering Information Very Low Dropout Low power consumption: 35uA(typ.) Output voltage ±2% Internal current limit and thermal shutdown Short circuit current fold-back Power saving shutdown mode Power good output function Adjustable output voltage Part No. Package Packing TS9004CX5 RF TS9004CX6 RF SOT-25 SOT-26 3Kpcs / 7” Reel 3Kpcs / 7” Reel Typical Application Circuit ● ● ● ● ● ● VOUT VIN Applications Palmtops Video recorders Battery powered equipment PC peripherals High-efficiency linear power supplies Digital Signal Camera EN off R1 on R2 C2 100p COUT 2.2uF Block Diagram VIN VOUT R1 EN off on R2 C2 100p COUT 2.2uF VOUT = 1.215 (R1+R2)/R2 C2 is unnecessary when R1 or R2 < 20K PG pin is only available in the SOT-26 package Connected to output for Power Good or left floating 1/7 Version: A07 TS9004 Series 300mA CMOS LDO Adjustable Voltage with Enable & Power Good Absolute Maximum Rating Parameter Symbol Limit Unit Input Supply Voltage VIN +8 Enable Input Voltage VCE Gnd-0.3 ~ VIN +0.3 Output Current IO PD / (VIN – VOUT) Power Dissipation PD Internal Limited Thermal Resistance ӨJA 140 Operating Ambient Temperature Range TA -40 ~ +85 Operating Junction Temperature Range TJ -40 ~ +125 Storage Temperature Range TSTG -65 ~ +150 o Lead Soldering Temperature (260 C) 10 ESD Classification HBM 2k Notes: Stress above the listed absolute rating may cause permanent damage to the device. V V mA o C/W o C o C o C S V Electrical Characteristics (Ta = 25oC, unless otherwise noted) Parameter Input Voltage Output Voltage Accuracy Symbol VIN VO Test Condition (Note 1) IO =1mA 1.5V< VO(NOM ≤2.0V 2.0V< VO(NOM ≤2.8V 2.8V< VO(NOM <3.8V VDROP IO =300mA VO =VO(NOM) -2.0% IO ILIM ISC IGND VO >1.2V VO >1.2V VO <0.8V (Note 2) IO =1mA to 300mA Line Regulation REGLINE IO =5mA VIN= VO +1 to VO +2 Load Regulation Over Temperature Shutdown Over Temperature Hysterisis VO Temperature Coefficient REGLOAD IO =1mA to 300mA Dropout Voltage Output Current Current Limit Short Circuit Current Ground Pin Current Power Supply Rejection Output Voltage Noise ADJ Input Bias Current ADJ Reference Voltage EN Input Threshold VO < 2.0V VO ≥ 2.0V Min Typ Max Units --2 ---300 300 ------ --- V % -450 150 35 -0.02 0.2 7 +2 1300 400 300 --300 -0.15 0.1 1 See chart mV mA mA mA mA % % % OTS -- 150 -- o OTH -- 30 -- o TC -- 30 -- ppm/ C PSRR eN IADJ VREF VEH VEL C C o IO =100mA CO=2.2mF f=100Hz f=1kHz f=10kHz ---- 60 50 20 ---- dB f=10Hz to 100kHz IO =10mA,CBYP=0mF CO =2.2nF -- 30 -- mVrms -1.2 2.0 0 1 1.215 --- -1.23 VIN 0.4 mA V V V VIN=2.7V to 7V VIN =2.7V to 7V 2/7 Version: A07 TS9004 Series 300mA CMOS LDO Adjustable Voltage with Enable & Power Good Electrical Characteristics (Ta = 25oC, unless otherwise noted) (Continue) Parameter EN Input Bias Current Symbol IEH IEL Test Condition VEN= VIN, VIN =2.7V to 7V VEN =0V, VIN =2.7V to 7V Min Typ Max Units --- --- 0.1 0.5 mA mA Shutdown Supply ISD VIN =5V, VO=0V VEN < VEL -0.5 1 mA Current Shutdown Output VO,SD IO =35mA, VEN < VEL 0 -0.1 V Voltage Output Under Voltage VUV --85 % VO (NOM) Output Over Voltage VOV 115 --% VO (NOM) PG Leakage Current ILC VPG=7V --1 mA PG Voltage Rating VPG VO in regulation --7 V PG Voltage Low VOL ISINK=0.4mA --0.4 V Note1: VIN(MIN)=VOUT+VDROPOUT Note2: To prevent the Short Circuit Current protection feature from being prematurely activated, the input voltage must be applied before a current source load is applied. Detailed Description The TS9004 family of CMOS regulators contain a PMOS pass transistor, voltage reference, error amplifier, overcurrent protection, thermal shutdown, and Power Good detection circuitry. The P-channel pass transistor receives data from the error amplifier, over-current shutdown, and thermal protection circuits. During normal operation, the error amplifier compares the output voltage to a precision o reference. Over-current and Thermal shutdown circuits become active when the junction temperature exceeds 150 C, or the current exceeds 300mA. During thermal shutdown, the o output voltage remains low. Normal operation is restored when the junction temperature drops below 120 C. The TS9004 switches from voltage mode to current mode when the load exceeds the rated output current. This prevents over-stress. The TS9004 also incorporates current foldback to reduce power dissipation when the output is short circuited. This feature becomes active when the output drops below 0.8volts, and reduces the current flow by 65%. Full current is restored when the voltage exceeds 0.8 volts. External Capacitors The TS9004 is stable with an output capacitor to ground of 2.2uF or greater. Ceramic capacitors have the lowest ESR, and will offer the best AC performance. Conversely, Aluminum Electrolytic capacitors exhibit the highest ESR, resulting in the poorest AC response. Unfortunately, large value ceramic capacitors are comparatively expensive. One option is to parallel a 0.1uF ceramic capacitor with a 10uF Aluminum Electrolytic. The benefit is low ESR, high capacitance, and low overall cost. A second capacitor is recommended between the input and ground to stabilize VIN. The input capacitor should be at least 0.1uF to have a beneficial effect. All capacitors should be placed in close proximity to the pins. A "Quiet" ground termination is desirable. This can be achieved with a "Star" connection. Enable The Enable pin normally floats high. When actively, pulled low, the PMOS pass transistor shuts off, and all internal circuits are powered down. In this state, the quiescent current is less than 1mA. This pin behaves much like an electronic switch. Power Good The TS9004 includes the Power Good feature. When the output is not within +10% of the specified voltage, it pulls low. This can occur under the following conditions: (1) Input Voltage too low. (2) During Over-Temperature. (3) During Over-Current. (4) If output is pulled up. (Note: PG pin is an open-drain output.) 3/7 Version: A07 TS9004 Series 300mA CMOS LDO Adjustable Voltage with Enable & Power Good Electrical Characteristics Curve Figure 1. Ground Current vs. Input Voltage Figure 2. Current Limit Response Figure 3. Line Transient Response Figure 4. Load Step (1mA~300mA) Figure 5. Chip Enable Transient Response Figure 6. Vdrop vs. Vout 4/7 Version: A07 TS9004 Series 300mA CMOS LDO Adjustable Voltage with Enable & Power Good SOT-26 Mechanical Drawing DIM 5/7 SOT-26 DIMENSION MILLIMETERS INCHES MIN MIN TYP MAX TYP A 0.95 BSC 0.0374 BSC A1 1.9 BSC MAX B 2.60 2.80 3.00 0.0748 BSC 0.1024 0.1102 0.1181 C 1.40 1.50 1.70 0.0551 0.0591 0.0669 0.1142 0.1220 0.0433 0.0472 D 2.80 2.90 3.10 0.1101 E 1.00 1.10 1.20 0.0394 F 0.00 -- 0.10 0.00 0.0157 0.0197 0.0039 G 0.35 0.40 0.50 0.0138 H 0.10 0.15 0.20 0.0039 0.0059 0.0079 I 0.30 -- 0.60 0.0118 -- 0.0236 J 5º -- 10º 5º -- 10º Version: A07 TS9004 Series 300mA CMOS LDO Adjustable Voltage with Enable & Power Good SOT-25 Mechanical Drawing DIM A+A1 B C D E E H L Ө1 S1 6/7 SOT-25 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX. 0.09 1.25 0.0354 0.0492 0.30 0.50 0.0118 0.0197 0.09 0.25 0.0035 0.0098 2.70 3.10 0.1063 0.1220 1.40 1.80 0.0551 0.0709 1.90 BSC 0.0748 BSC 2.40 3.00 0.09449 0.1181 0.35 BSC 0.0138 BSC 0º 10º 0º 10º 0.95 BSC 0.0374 BSC Version: A07 TS9004 Series 300mA CMOS LDO Adjustable Voltage with Enable & Power Good Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 7/7 Version: A07