UFM201L THRU UFM204L SURFACE MOUNT GLASS PASSIVATED SUPER FAST SILICON RECTIFIER VOLTAGE RANGE 50 to 200 Volts CURRENT 2.0 Amperes FEATURES * * * * * Glass passivated device For surface mounted applications Ultrafast recovery times dor high efficiency Low forward voltage, low power loss Low leakage current SMBL MECHANICAL DATA * * * * Epoxy: Device has UL flammability classification 94V-O Metallurgically bonded construction Mounting position: Any Weight: 0.098 gram 0.083 (2.11) 0.077 (1.96) 0.155 (3.94) 0.130 (3.30) 0.180 (4.57) 0.160 (4.06) 0.012 (0.305) 0.006 (0.152) 0.085 (2.15) 0.061 (1.55) 0.060 (1.52) 0.030 (0.76) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS 0.008 (0.203) 0.004 (0.102) Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. 0.220 (5.59) 0.205 (5.21) For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted) SYMBOL UFM201L UFM202L UFM203L UFM204L UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 Volts Maximum RMS Voltage VRMS 35 70 105 140 Volts VDC 50 100 150 200 Volts RATINGS Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 55 OC IO 2.0 Amps I FSM 50 Amps Typical Thermal Resistance (Note 1) RqJA 75 0 C/W Typical Thermal Resistance (Note 1) RqJL 20 0 C/W Typical Junction Capacitance (Note 2) CJ 18 Operating Temperature Range TJ 150 0 C T STG -55 to + 150 0 C Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Storage Temperature Range pF ELECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 2.0A DC Maximum Average Reverse Current @T A = 25 o C at Rated DC Blocking Voltage @T A = 100 o C Maximum Reverse Recovery Time (Note 4) NOTES : 1. 2. 3. 4. SYMBOL VF IR trr Thermal Resistance :Mounted on PCB. Measured at 1 MHz and applied reverse voltage of 4.0 volts. "Fully ROHS compliant","100% Sn plating (Pb-free)". Test Conditions: I F= 0.5A, I R= -1.0A, I RR= -0.25A. UFM201L UFM202L UFM203L UFM204L UNITS 0.9 Volts 5 mA 350 mA 20 nSec 2006-12 RATING AND CHARACTERISTICS CURVES ( UFM201L THRU UFM204L ) 50 W NONINDUCTIVE (+) 25 Vdc (approx) (-) (-) D.U.T PULSE GENERATOR (NOTE 2) 1 NONINDUCTIVE trr +0.5A 10 W NONINDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) NOTES: 1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. -1.0A 2. Rise Time = 10ns max. Source Impedance = 50 ohms. 1cm SET TIME BASE FOR 8/1 ns/cm AVERAGE FORWARD CURRENT, (A) 2.5 2.0 1.5 1.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.5 0 0 25 50 75 100 125 150 AMBIENT TEMPERATURE, (OC) FIG.2 TYPICAL FORWARD CURRENT DERATING CURVE 175 INSTANTANEOUS REVERSE CURRENT, (uA) FIG.1 TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 1000 TA = 100 OC 100 10 TA = 75 OC TA = 25 OC 1.0 0.1 0 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG.3 TYPICAL REVERSE CHARACTERISTICS 140 PEAK FORWARD SURGE CURRENT, (A) 20 10 TJ = 25 OC 3.0 1.0 0.3 0.1 0.03 0.01 Pulse Width=300uS 1% Duty Cycle 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 200 8.3ms Single Half Sine-Wave (JEDED Method) 100 50 30 20 10 1 5 INSTANTANEOUS FORWARD VOLTAGE, (V) 10 TJ = 25 OC 100 60 40 20 10 6 4 2 0.1 0.2 100 FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 200 1 50 NUMBER OF CYCLES AT 60Hz FIG.4 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS JUNCTION CAPACITANCE, (pF) INSTANTANEOUS FORWARD CURRENT, (A) RATING AND CHARACTERISTICS CURVES ( UFM201L THRU UFM204L ) 0.4 1.0 2 4 10 20 40 REVERSE VOLTAGE, (V) FIG.6 TYPICAL JUNCTION CAPACITANCE 100 Mounting Pad Layout 0.106 MAX. (2.69 MAX.) 0.083MIN. ( 2.10 MIN.) 0.050 MAX. (1.27 MAX.) 0.220 (5.58) REF Dimensions in inches and (millimeters) DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.