rev. page 1 of 5 date 01/2011 DESCRIPTION: switching power supply PART NUMBER: VF-S320-XXA features · · · · · · · power factor correction power good signal short circuit protection over load protection over voltage protection over temperature protection providing Peak Power 700W within 500uS duty · approved to UL, CUL, TUV, CE with CB scheme · high power density: 8.9 watts/inch 3 E210311 output 1,2 2 - 5.5 V 6 - 10 V 12 - 13.5 V 13.6 - 15 V 16 - 20 V 21 - 26 V 27 - 34 V 35 - 42 V 43 - 50 V 51 - 60 V MODEL VF-S320-05A VF-S320-09A VF-S320-12A VF-S320-15A VF-S320-18A VF-S320-24A VF-S320-28A VF-S320-36A VF-S320-48A VF-S320-54A preset voltage 5 V 9 V 12 V 15 V 18 V 24 V 28 V 36 V 48 V 54 V output current convection 5 22 CFM 5 27.28 A 45 A 16.37 A 29.1 A 15 A 26.67 A 12 A 21.33 A 10 A 17.78 A 7.5 A 13.33 A 6.43 A 11.43 A 5A 8.89 A 3.75 A 6.67 A 3.33 A 5.93 A regulation 3 ±1% ±1% ±1% ±1% ±1% ±1% ±1% ±1% ±1% ±1% ripple & noise 3,4 (Vpp) 50 mV ±1% ±1% ±1% ±1% ±1% ±1% ±1% ±1% ±1% notes: 1 Output is fully isolated. 2 Output voltage is measured at output power connector. 3 1% minimum load is required to maintain the ripple and regulation. 4 Ripple and noise is measured from 10 KHz to 20 MHz at output terminals with a 0.1 μF ceramic capacitor and a 22 μF electrolytic capacitor in parallel. 5 Maximum power is 320 W with 22 CFM airflow. 5 and 9 V units maximum current is listed. Maximum power is 180 W with convection. CUSTOM CONFIG KEY VF-S320- XX A- X X - CXX Output voltage Input/Output connector: “blank” = Terminal block input / Terminal block output 1 = Molex input / Molex output 2 = Molex input / Terminal block output 3 = Terminal block input / Molex output Reserved for custom configurations Low leakage option: “blank” = standard specification L = low leakage (contact factory) 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 www.v-infinity.com rev. PART NUMBER: VF-S320-XXA page 2 of 5 date 01/2011 DESCRIPTION: switching power supply INPUT parameter input frequency input voltage Input current inrush current inrush current power factor conditions/description min 47 90 nom max 63 264 8 4 70 35 units Hz V ac A A A A conditions/description min Output voltage returns to within 1% in less than 2.5 ms for a 50% load change. Peak transient does not exceed 5%. Turn-on and turn-off overshoot shall not exceed 5% over nominal voltage. Measured at 230 V and full load 3.3 model: 70% 5 V model: 75% 12 V model: 80% All other models: 83% At 120 V ac At 120 V ac and 80% of rated maximim load Adjustable with built-in trim pot. ±5% When green (LED1) is on the power supply is operating normally. Designated as PG on the CN1. This signal goes TTL high 100-500 ms after the output reaches regulation. It goes low at least 1 mS before loss of regulation. 12 V dc/4G00mA for external fan nom max units 90-132 / 180-264 auto-selectable At 100-120 V ac At 200-240 V ac Peak measured at 230 V ac at full load, cold start Peak measured at 115 V ac at full load, cold start Passive power factor correction meets EN61000-3-2 class A OUTPUT parameter transient response overshoot efficiency turn on delay hold up time adjustability LED display power good fan drive 1 20 Wsecond ms PROTECTION CIRCUIT parameter input fuse overload short circuit output over-voltage over temp. conditions/description Built-in ac fuse. A blown fuse usually indicates permanent damage to the power supply serviceable by factory only. Current limiting starts at 110-140% of the rated output current in foldback mode and recovers automatically. Short circuit can be continuous. Recovers automatically upon removal of short. Output is protected agaist overvoltage. Unit shuts down and latches when voltage at output terminals exceeds 130%. AC input needs to be reset to restart the power supply. Power supply shuts down when temperature is in excess of 85 ºC. Auto recovery. 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 www.v-infinity.com rev. PART NUMBER: VF-S320-XXA page 3 of 5 date 01/2011 DESCRIPTION: switching power supply GENERAL AND SAFTEY parameter operating temp. conditions/description 0 to 70ºC ambient, de-rating at 2.5% per degree from 50ºC to 70ºC. storage temp. operating humid. storage humid. EMI safety leakage current vibration isolation voltage (HI-POT) grounding test warranty MTBF burn-in cooling min 0 nom max 50 units ºC -20 Non-condensing 5% Non-condensing 5% Pass FCC Part 15, CISPR 22 class B, Conducted UL60950-1, CSA C22.2 No. 60950-1-03, TUV EN60950-1, CE Mark (LVD) EN61000-3-(2,3) & IEC61000-4 Series regulations and CB at 240 V ac Acceleration ± 7.35 M/(SxS), on X, Y and Z Axis 5 Applied for 3 seconds at 10 mA Primary to secondary: 3,000 Primary to transformer core: 1,500 Primary to earth chassis: 1,500 Allowable resistance measured when 25 A current is applied from the ground pin of the three prong plug to the farthest earthed connection point. Standard warranty length According to MIL-HDBK-217 at 30 ºC 100,000 Full load, at 45 ± 5 ºC, 230 V ac Built-in DC fan speed control. 85 90% 95% ºC RH RH 1.5 50 mA Hz 0.1 V ac V ac V ac Ω conditions/description max 600 2 1 years hours hours MECHANICAL parameter weight enclosure min nom 6(L) x 4(W) x 1.5(H) units grams inches LOGIC SIGNAL CONNECTOR - (CN1) parameter CN1 conditions/description JST B2B-XH-4 or equivalent (CHYAO SHIUNN JS-1001-03) Suggested mating connector: JST XHP-3 or equivalent (CHYAO SHIUNN JS-2001-03) FAN DRIVER CONNECTOR - (FAN2) parameter FAN2 conditions/description Suggested mating connector: JST XHP-2 (2 pins 0.98 pitch) or equivalent (CHYAO SHIUNN JS-2001-02) 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 www.v-infinity.com rev. PART NUMBER: VF-S320-XXA page 4 of 5 date 01/2011 DESCRIPTION: switching power supply INPUT / OUTPUT CONNECTOR - (CN2) parameter option 1 option 2 conditions/description AC INPUT JST VH series (5 pin with pins 2 and 4 removed) or equivalent (Chyao Shiunn JS-1120-05) Suggested mating plug: JST VHR-5N (5 pin) or equivalent (Chyao Shiunn JS-1121-05) contact: JST SVH series or similar DC OUTPUT JST VH series (10 pin) or equivalent (Chyao Shiunn JS-1120-10) Suggested mating plug: JST VHR-10N (10 pin) or equivalent (Chyao Shiunn JS-1121-10) contact: JST SVH series or similar Howder Terminal block Part No. HB-95-7P (7 pin, M3.5 Screw) 9.5mm spacing Suggested mating connector: Molex 19198-0045 or similar 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 www.v-infinity.com REV. A DESCRIPTION NEW DRAWING DATE 6/26/2008 152.40 6.000 38.10 1.500 FAN2 + - CN1 FF 101.60 4.000 (2 PLCS) connector part no. JS-1120-05 (5 pins, 3 used) PG DETAIL A SCALE 2 : 1 L L 76.20 3.000 (2 PLCS) RTN N N G G VO- VO- VO+ VO+ 101.60 4.000 A UNC 8-32 (6 PLCS) terminal block option M3.5 screw 7pins 9.5mm center connector part no. JS-1120-10 (10 pins) SCALE: 1:3 RoHS TOLERANCE: ±0.3mm UNLESS OTHERWISE SPECIFIED 25.40 1.000 (2 PLCS) 101.60 4.000 25.40 1.000 20050 SW 112th Ave. Tualatin, OR 97062 Phone: 503-612-2300 800-275-4899 Fax: 503-612-2383 Website: www.cui.com NOTE: MOUNTING HOLE MAX DEPTH 4.00mm TITLE: SWITCHING POWER SUPPLY PART NO. PC FILE NAME: VF-S320-XXA Series VF-S320-XXA Series DRAWN BY: COPYRIGHT 2008 BY CUI INC. ZRJ APPROVED BY: REV: A UNITS: MM [INCHES] SCALE: 1:2