Replaces X25383 X5083 CPU Supervisor with 8Kbit SPI EEPROM FEATURES DESCRIPTION • Selectable time out watchdog timer • Low VCC detection and reset assertion —Five standard reset threshold voltages —Re-program low VCC reset threshold voltage using special programming sequence. —Reset signal valid to VCC = 1V • Long battery life with low power consumption —<50µA max standby current, watchdog on —<1µA max standby current, watchdog off —<400µA max active current during read • 1.8V to 3.6V, 2.7V to 5.5V and 4.5V to 5.5V power supply versions • 8Kbits of EEPROM—1m write cycle endurance • Save critical data with Block Lock™ memory —Block lock first or last page, any 1/4 or lower 1/2 of EEPROM array • Built-in inadvertent write protection —Write enable latch —Write protect pin • 3.3MHz clock rate • Minimize programming time —16 byte page write mode —Self-timed write cycle —5ms write cycle time (typical) • SPI modes (0,0 & 1,1) • Available packages —8-lead TSSOP, 8-lead SOIC This device combines four popular functions, Power-on Reset Control, Watchdog Timer, Supply Voltage Supervision, and Block Lock Serial EEPROM Memory in one package. This combination lowers system cost, reduces board space requirements, and increases reliability. Applying power to the device activates the power on reset circuit which holds RESET active for a period of time. This allows the power supply and oscillator to stabilize before the processor can execute code. The Watchdog Timer provides an independent protection mechanism for microcontrollers. When the microcontroller fails to restart a timer within a selectable time out interval, the device activates the RESET signal. The user selects the interval from three preset values. Once selected, the interval does not change, even after cycling the power. The device’s low VCC detection circuitry protects the user’s system from low voltage conditions, resetting the system when VCC falls below the minimum VCC trip point. RESET is asserted until VCC returns to the proper operating level and stabilizes. Five industry standard VTRIP thresholds are available, however, Xicor’s unique circuits allow the threshold to be reprogrammed to meet custom requirements or to fine-tune the threshold for applications requiring higher precision. BLOCK DIAGRAM Watchdog Transition Detector WP SO SCK CS/WDI Protect Logic RESET Data Register Status Register Command Decode & Control Logic 16 Bytes 240 Bytes VCC Threshold Reset logic 256 Bytes 256 Bytes 240 Bytes 16 Bytes VCC + VTRIP REV 1.1 9/25/00 - www.xicor.com EEPROM Array SI Watchdog Timer Reset Reset & Watchdog Timebase Power On and Low Voltage Reset Generation Characteristics subject to change without notice. 1 of 20 X5083 PIN CONFIGURATION 8-Lead SOIC 8-Lead TSSOP RESET 1 VCC 2 CS/WDI 3 SO 4 X5083 CS/WDI 1 SI SO 2 VSS WP 3 WP VSS 4 8 SCK 7 6 5 8 X5083 VCC 7 RESET 6 SCK 5 SI PIN DESCRIPTION Pin (SOIC/PDIP) Pin TSSOP Name Function 1 1 CS/WDI Chip Select Input. CS HIGH, deselects the device and the SO output pin is at a high impedance state. Unless a nonvolatile write cycle is underway, the device will be in the standby power mode. CS LOW enables the device, placing it in the active power mode. Prior to the start of any operation after power up, a HIGH to LOW transition on CS is required. Watchdog Input. A HIGH to LOW transition on the WDI pin restarts the Watchdog timer. The absence of a HIGH to LOW transition within the watchdog time out period results in RESET going active. 2 2 SO Serial Output. SO is a push/pull serial data output pin. A read cycle shifts data out on this pin. The falling edge of the serial clock (SCK) clocks the data out. 5 8 SI Serial Input. SI is a serial data input pin. Input all opcodes, byte addresses, and memory data on this pin. The rising edge of the serial clock (SCK) latches the input data. Send all opcodes (Table 1), addresses and data MSB first. 6 9 SCK Serial Clock. The Serial Clock controls the serial bus timing for data input and output. The rising edge of SCK latches in the opcode, address, or data bits present on the SI pin. The falling edge of SCK changes the data output on the SO pin. 3 6 WP Write Protect. When WP is LOW, nonvolatile write operations to the memory are prohibited. This “Locks” the memory to protect it against inadvertent changes when WP is HIGH, the device operates normally. 4 7 VSS Ground 8 14 VCC Supply Voltage 7 13 RESET 3-5,10-12 NC REV 1.1 9/25/00 Reset Output. RESET is an active LOW, open drain output which goes active whenever VCC falls below the minimum VCC sense level. It will remain active until VCC rises above the minimum VCC sense level for 250ms. RESET goes active if the watchdog timer is enabled and CS remains either HIGH or LOW longer than the selectable watchdog time out period. A falling edge of CS will reset the watchdog timer. RESET goes active on power up at about 1V and remains active for 250ms after the power supply stabilizes. No internal connections www.xicor.com Characteristics subject to change without notice. 2 of 20 X5083 PRINCIPLES OF OPERATION Power On Reset Application of power to the X5083 activates a power on reset circuit. This circuit goes LOW at 1V and pulls the RESET pin active. This signal prevents the system microprocessor from starting to operate with insufficient voltage or prior to stabilization of the oscillator. When VCC exceeds the device VTRIP value for 200ms (nominal) the circuit releases RESET, allowing the processor to begin executing code. Low Voltage Monitoring During operation, the X5083 monitors the VCC level and asserts RESET if supply voltage falls below a preset minimum VTRIP. The RESET signal prevents the microprocessor from operating in a power fail or brownout condition. The RESET signal remains active until the voltage drops below 1V. It also remains active until VCC returns and exceeds VTRIP for 200ms. Watchdog Timer The watchdog timer circuit monitors the microprocessor activity by monitoring the WDI input. The microprocessor must toggle the CS/WDI pin periodically to prevent a RESET signal. The CS/WDI pin must be toggled from HIGH to LOW prior to the expiration of the watchdog time out period. The state of two nonvolatile control bits in the status register determine the watchdog timer period. The microprocessor can change these watchdog bits with no action taken by the microprocessor these bits remain unchanged, even after total power failure. VCC Threshold Reset Procedure The X5083 is shipped with a standard VCC threshold (VTRIP) voltage. This value will not change over normal operating and storage conditions. However, in applications where the standard VTRIP is not exactly right, or if higher precision is needed in the VTRIP value, the X5083 threshold may be adjusted. The procedure is described below, and uses the application of a high voltage control signal. Setting the VTRIP Voltage This procedure is used to set the VTRIP to a higher voltage value. For example, if the current VTRIP is 4.4V and the new VTRIP is 4.6V, this procedure will directly make the change. If the new setting is to be lower than the current setting, then it is necessary to reset the trip point before setting the new value. To set the new VTRIP voltage, apply the desired VTRIP threshold voltage to the VCC pin and tie the WP pin to the programming voltage VP. Then send a WREN command, followed by a write of Data 00h to address 01h. CS going HIGH on the write operation initiates the VTRIP programming sequence. Bring WP LOW to complete the operation. Note: This operation also writes 00h to array address 01h. Figure 1. Set VTRIP Level Sequence (VCC = desired VTRIP value) VPE = 15-18V WP CS 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 8 9 10 20 21 22 23 SCK 16 Bits SI 06h WREN REV 1.1 9/25/00 02h Write www.xicor.com 0001h Address 00h Data Characteristics subject to change without notice. 3 of 20 X5083 Resetting the VTRIP Voltage This procedure is used to set the VTRIP to a “native” voltage level. For example, if the current VTRIP is 4.4V and the new VTRIP must be 4.0V, then the VTRIP must be reset. When VTRIP is reset, the new VTRIP is something less than 1.7V. This procedure must be used to set the voltage to a lower value. To reset the new VTRIP voltage, apply the desired VTRIP threshold voltage to the Vcc pin and tie the WP pin to the programming voltage VP. Then send a WREN command, followed by a write of data 00h to address 03h. CS going HIGH on the write operation initiates the VTRIP programming sequence. Bring WP LOW to complete the operation. Note: This operation also writes 00h to array address 03h. Figure 2. Reset VTRIP Level Sequence (VCC > 3V. WP = 15–18V) VPE = 15-18V WP CS 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 8 9 10 20 21 22 23 SCK 16 Bits SI 06h WREN 02h Write 00h Data 0003h Address Figure 3. Sample VTRIP Reset Circuit 4.7K VP Adjust VTRIP Adj. Run 1 2 3 4 8 X5083 RESET µC 7 6 SCK 5 SI SO CS REV 1.1 9/25/00 www.xicor.com Characteristics subject to change without notice. 4 of 20 X5083 Figure 4. VTRIP Programming Sequence VTRIP Programming Execute Reset VTRIP Sequence Set VCC = VCC Applied = Desired VTRIP Execute Set VTRIP Sequence New VCC Applied = Old VCC Applied + Error New VCC Applied = Old VCC Applied - Error Apply 5V to VCC Execute Reset VTRIP Sequence Decrement VCC (VCC = VCC - 50mV) NO RESET pin goes active? YES Error ≤ –Emax Measured VTRIP Desired VTRIP Error ≥ Emax –Emax < Error < Emax DONE Emax = Maximum Desired Error SPI Serial Memory The memory portion of the device is a CMOS serial EEPROM array with Xicor’s block lock protection. The array is internally organized as x 8. The device features a Serial Peripheral Interface (SPI) and software protocol allowing operation on a simple four-wire bus. The device utilizes Xicor’s proprietary Direct Write™ cell, providing a minimum endurance of 1,000,000 cycles and a minimum data retention of 100 years. REV 1.1 9/25/00 The device is designed to interface directly with the synchronous Serial Peripheral Interface (SPI) of many popular microcontroller families. The device monitors the bus and asserts RESET output if there is no bus activity within user selectable time out period or the supply voltage falls below a preset minimum VTRIP. The device contains an 8-bit instruction register. It is accessed via the SI input, with data being clocked in on the rising edge of SCK. CS must be LOW during the entire operation. www.xicor.com Characteristics subject to change without notice. 5 of 20 X5083 All instructions (Table 1), addresses and data are transferred MSB first. Data input on the SI line is latched on the first rising edge of SCK after CS goes LOW. Data is output on the SO line by the falling edge of SCK. SCK is static, allowing the user to stop the clock and then start it again to resume operations where left off. Write Enable Latch The device contains a Write Enable Latch. This latch must be SET before a Write Operation is initiated. The WREN instruction will set the latch and the WRDI instruction will reset the latch (Figure 3). This latch is automatically reset upon a power-up condition and after the completion of a valid Write Cycle. Status Register The RDSR instruction provides access to the status register. The status register may be read at any time, even during a write cycle. The status register is formatted as follows. Status Register/Block Lock/WDT Byte 7 6 5 4 3 2 1 0 0 0 0 WD1 WD0 BL2 BL1 BL0 Block Lock Memory Xicor’s block lock memory provides a flexible mechanism to store and lock system ID and parametric information. There are seven distinct block lock memory areas within the array which vary in size from one page to as much as half of the entire array. These areas and associated address ranges are block locked by writing the appropriate two byte block lock instruction to the device as described in Table 1 and Figure 7. Once a block lock instruction has been completed, that block lock setup is held in the nonvolatile status register until the next block lock instruction is issued. The sections of the memory array that are block locked can be read but not written until block lock is removed or changed. Table 1. Instruction Set and Block Lock Protection Byte Definition Instruction Format Instruction Name and Operation 0000 0110 WREN: set the write enable latch (write enable operation) 0000 0100 WRDI: reset the write enable latch (write disable operation) 0000 0001 Write status instruction—followed by: Block lock/WDT byte: (See Figure 1) 000WD1 WD2000 --->no block lock: 00h-00h 000WD1 WD2001 --->block lock Q1: 0000h-00FFh 000WD1 WD2010 --->block lock Q2: 0100h-01FFh 000WD1 WD2011 --->block lock Q3: 0200h-02FFh 000WD1 WD2100 --->block lock Q4: 0300h-03FFh 000WD1 WD2101 --->block lock H1: 0000h-01FFh 000WD1 WD2110 --->block lock P0: 0000h-000Fh 000WD1 WD2111 --->block lock Pn: 03F0h-03FFh --->none of the array --->lower quadrant (Q1) --->Q2 --->Q3 --->upper quadrant (Q4) --->lower half of the array (H1) --->lower page (P0) --->upper page (PN) 0000 0101 READ STATUS: reads status register & provides write in progress status on SO pin 0000 0010 WRITE: write operation followed by address and data 0000 0011 READ: read operation followed by address Watchdog Timer The watchdog timer bits, WD0 and WD1, select the watchdog time out period. These nonvolatile bits are programmed with the WRSR instruction. REV 1.1 9/25/00 Status Register Bits WD1 WD0 Watchdog Time Out (Typical) 0 0 1.4 seconds 0 1 600 milliseconds 1 0 200 milliseconds 1 1 disabled www.xicor.com Characteristics subject to change without notice. 6 of 20 X5083 Read Sequence When reading from the EEPROM memory array, CS is first pulled low to select the device. The 8-bit READ instruction is transmitted to the device, followed by the 16-bit address. After the READ opcode and address are sent, the data stored in the memory at the selected address is shifted out on the SO line. The data stored in memory at the next address can be read sequentially by continuing to provide clock pulses. The address is automatically incremented to the next higher address after each byte of data is shifted out. When the highest address is reached, the address counter rolls over to address $0000 allowing the read cycle to be continued indefinitely. The read operation is terminated by taking CS high. Refer to the read EEPROM array sequence (Figure 1). To write to the status register, the WRSR instruction is followed by the data to be written (Figure 5). Data bits 5, 6 and 7 must be “0”. To read the status register, the CS line is first pulled low to select the device followed by the 8-bit RDSR instruction. After the RDSR opcode is sent, the contents of the status register are shifted out on the SO line. Refer to the read status register sequence (Figure 2). Clocking SCK is valid during a nonvolatile write in progress, but is not necessary. If the SCK line is clocked, the pointer to the status register is also clocked, even though the SO pin shows the status of the nonvolatile write operation (See Figure 3). Write Sequence Prior to any attempt to write data into the device, the “Write Enable” Latch (WEL) must first be set by issuing the WREN instruction (Figure 3). CS is first taken LOW, then the WREN instruction is clocked into the device. After all eight bits of the instruction are transmitted, CS must then be taken HIGH. If the user continues the write operation without taking CS HIGH after issuing the WREN instruction, the write operation will be ignored. RESET Operation The RESET output is designed to go LOW whenever VCC has dropped below the minimum trip point and/or the watchdog timer has reached its programmable time out limit. To write data to the EEPROM memory array, the user then issues the WRITE instruction followed by the 16 bit address and then the data to be written. Any unused address bits are specified to be “0’s”. The WRITE operation minimally takes 32 clocks. CS must go low and remain low for the duration of the operation. If the address counter reaches the end of a page and the clock continues, the counter will roll back to the first address of the same page and overwrite any data that may have been previously written. – The device is in the low power standby state. For a write operation (byte or page write) to be completed, CS can only be brought HIGH after bit 0 of the last data byte to be written is clocked in. If it is brought HIGH at any other time, the write operation will not be completed (Figure 4). REV 1.1 9/25/00 Read Status Operation If there is not a nonvolatile write in progress, the read status instruction returns the block lock setting from the status register which contains the block lock bits IDL2IDL0 (Figure 1). The block lock bits define the block lock condition (Figure 1/Table1). The other bits are reserved and will return’0’ when read. See Figure 3. If a nonvolatile write is in progress, the read status instruction returns a HIGH on SO. When the nonvolatile write cycle is completed, the status register data is read out. The RESET output is an open drain output and requires a pull up resistor. Operational Notes The device powers-up in the following state: – A HIGH to LOW transition on CS is required to enter an active state and receive an instruction. – SO pin is high impedance. – The write enable latch is reset. – Reset signal is active for tPURST. Data Protection The following circuitry has been included to prevent inadvertent writes: – A WREN instruction must be issued to set the write enable latch. – CS must come HIGH at the proper clock count in order to start a nonvolatile write cycle. www.xicor.com Characteristics subject to change without notice. 7 of 20 X5083 Figure 5. Read Operation Sequence CS 0 1 2 3 4 5 6 7 8 20 21 22 23 24 25 26 27 28 29 30 9 SCK Read Instruction (1 Byte) Byte Address (2 Byte) 15 14 SI 3 2 Data Out 1 0 High Impedance 7 SO 6 5 4 3 2 1 0 Figure 6. Read Status Operation Sequence CS 0 1 2 3 4 5 6 7 ... SCK Read Status Instruction ... SI W D 1 SO W D 0 B L 2 B L 1 B L 0 ... SO = Status Reg When no Nonvolatile Write Cycle Figure 7. WREN/WRDI Sequence CS 0 1 2 3 4 5 6 7 SCK Instruction (1 Byte) SI SO REV 1.1 9/25/00 High Impedance www.xicor.com Characteristics subject to change without notice. 8 of 20 X5083 Figure 8. EEPROM Array Write Sequence CS 0 1 2 3 4 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31 SCK Instruction 16 Bit Address 15 14 13 3 2 SI 1 0 7 6 Data Byte 1 5 4 3 2 1 0 CS 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 SCK SI 7 6 5 Data Byte 2 4 3 2 1 0 7 Data Byte 3 5 4 3 2 6 1 0 6 5 Data Byte N 4 3 2 1 0 Figure 9. Status Register Write Sequence CS 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 6 5 4 SCK Data Byte Instruction SI SO REV 1.1 9/25/00 High Impedance www.xicor.com 3 2 1 0 W W D D 1 0 B L 2 B L 1 B L 0 Characteristics subject to change without notice. 9 of 20 X5083 Figure 10. Read Nonvolatile Write Status (Option 1) CS 0 1 2 3 4 5 6 7 SCK Read Status Instruction SI Nonvolatile Write in Progress SO SO HIGH During 1st Bit While in the Nonvolatile Write Cycle Figure 11. Read Nonvolatile Write Status (Option 2) CS 0 1 2 3 4 5 6 7 SCK RWDT Instruction SI Nonvolatile Write in Progress SO SO HIGH During Nonvolatile Write Cycle SYMBOL TABLE WAVEFORM REV 1.1 9/25/00 INPUTS OUTPUTS Must be steady Will be steady May change from LOW to HIGH Will change from LOW to HIGH May change from HIGH to LOW Will change from HIGH to LOW Don’t Care: Changes Allowed N/A Changing: State Not Known Center Line is High Impedance www.xicor.com Characteristics subject to change without notice. 10 of 20 X5083 ABSOLUTE MAXIMUM RATINGS COMMENT Temperature under bias .................. –65°C to +135°C Storage temperature ....................... –65°C to +150°C Voltage on any pin with respect to VSS ......................................–1.0V to +7V D.C. output current ............................................... 5mA Lead temperature (soldering, 10 seconds)........ 300°C Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; the functional operation of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS Temperature Min. Max. Voltage Option Limits Commercial 0°C 70°C –1.8 1.8V-3.6V Industrial –40°C +85°C –2.7 2.7V to 5.5V Blank 4.5V-5.5V D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.) Limits Symbol Parameter ICC1 Min. Typ. Max. Unit Test Conditions VCC write current (active) 5 mA SCK = VCC x 0.1/VCC x 0.9 @ 5MHz, SO = Open ICC2 VCC read current (active) 0.4 mA SCK = VCC x 0.1/VCC x 0.9 @ 5MHz, SO = Open ISB1 VCC standby current WDT = OFF 1 µA CS = VCC, VIN = VSS or VCC, VCC = 5.5V ISB2 VCC standby current WDT = ON 50 µA CS = VCC, VIN = VSS or VCC, VCC = 5.5V ISB3 VCC standby current WDT = ON 20 µA CS = VCC, VIN = VSS or VCC, VCC = 3.6V ILI Input leakage current 0.1 10 µA VIN = VSS to VCC ILO Output leakage current 0.1 10 µA VOUT = VSS to VCC (1) Input LOW voltage –0.5 VCC x 0.3 V (1) VIH Input HIGH voltage VCC x 0.7 VCC + 0.5 V VOL1 Output LOW voltage 0.4 V VCC > 3.3V, IOL = 2.1mA VOL2 Output LOW voltage 0.4 V 2V < VCC ≤ 3.3V, IOL = 1mA VOL3 Output LOW voltage 0.4 V VCC ≤ 2V, IOL = 0.5mA VOH1 Output HIGH voltage VCC – 0.8 V VCC > 3.3V, IOH = –1.0mA VOH2 Output HIGH voltage VCC – 0.4 V 2V < VCC ≤ 3.3V, IOH = –0.4mA VOH3 Output HIGH voltage VCC – 0.2 V VCC ≤ 2V, IOH = –0.25mA VOLRS Reset output LOW voltage V IOL = 1mA VIL REV 1.1 9/25/00 0.4 www.xicor.com Characteristics subject to change without notice. 11 of 20 X5083 POWER-UP TIMING Symbol (2) (2) tPUR tPUW Parameter Min. Max. Unit Power-up to read operation 1 ms Power-up to write operation 5 ms Max. Unit Conditions Output capacitance (SO, RESET, RESET) 8 pF VOUT = 0V Input capacitance (SCK, SI, CS, WP) 6 pF VIN = 0V CAPACITANCE TA = +25°C, f = 1MHz, VCC = 5V. Symbol (2) COUT (2) CIN Test Notes: (1) VIL min. and VIH max. are for reference only and are not tested. (2) This parameter is periodically sampled and not 100% tested. EQUIVALENT A.C. LOAD CIRCUIT AT 5V VCC 5V A.C. TEST CONDITIONS 5V 3.3KΩ 1.64KΩ Output Input pulse levels VCC x 0.1 to VCC x 0.9 Input rise and fall times 10ns Input and output timing level VCC x0.5 RESET 1.64KΩ 100pF 30pF A.C. CHARACTERISTICS (Over recommended operating conditions, unless otherwise specified) Data Input Timing 1.8–3.6V Symbol Parameter 2.7V–5.5V Min. Max. Min. Max. Unit 0 2 0 3.3 MHz fSCK Clock frequency tCYC Cycle time 500 300 ns tLEAD CS lead time 250 150 ns tLAG CS lag time 250 150 ns tWH Clock HIGH time 200 130 ns tWL Clock LOW time 200 130 ns tSU Data setup time 50 20 ns tH Data hold time 50 20 ns (3) Input rise time 2 2 µs (3) tFI Input fall time 2 2 µs tCS CS deselect time tWC(4) Write cycle time 10 ms tRI REV 1.1 9/25/00 250 100 10 www.xicor.com ns Characteristics subject to change without notice. 12 of 20 X5083 Data Output Timing 1.8–3.6V Symbol Parameter fSCK Clock frequency tDIS Output disable time Min. Max. Min. Max. Unit 0 2 0 3.3 MHz 150 ns 250 Output valid from clock low tV 2.7V–5.5V 200 130 Output hold time tRO(3) Output rise time 100 50 ns Output fall time 100 50 ns (3) tFO 0 ns tHO 0 ns Notes: (3) This parameter is periodically sampled and not 100% tested. (4) tWC is the time from the rising edge of CS after a valid write sequence has been sent to the end of the self-timed internal nonvolatile write cycle. Serial Output Timing CS tCYC tWH tLAG SCK tV SO SI tWL tHO MSB Out tDIS MSB–1 Out LSB Out ADDR LSB IN Serial Input Timing tCS CS tLEAD tLAG SCK tSU SI SO REV 1.1 9/25/00 tH tRI MSB IN tFI LSB IN High Impedance www.xicor.com Characteristics subject to change without notice. 13 of 20 X5083 Power-Up and Power-Down Timing VCC VTRIP tPURST tPURST 0 Volts tR VTRIP tF tRPD RESET (X5083) RESET Output Timing Symbol Parameter Min. Typ. Max. Unit VTRIP Reset trip point voltage, X5083PT-4.5A Reset trip point voltage, X5083PT Reset trip point voltage, X5083PT-2.7A Reset trip point voltage, X5083PT-2.7 Reset trip point voltage, X5083PT-1.8 4.5 4.25 2.85 2.55 1.7 4.63 4.38 2.93 2.63 1.75 4.75 4.5 3.00 2.7 1.8 V tPURST Power-up reset time out 100 200 280 ms 500 ns (5) tRPD VCC fall time 0.1 ns (5) VCC rise time 0.1 ns 1 V tF tR VRVALID Note: VCC detect to reset/output (5) Reset valid VCC (5) This parameter is periodically sampled and not 100% tested. PT= Package/Temperature CS vs. RESET Timing CS tCST RESET tWDO tRST tWDO tRST RESET Output Timing Symbol Min. Typ. Max. Unit Watchdog time out period, WD1 = 1, WD0 = 0 WD1 = 0, WD0 = 1 WD1 = 0, WD0 = 0 100 450 1 200 600 1.4 300 800 2 ms ms sec tCST CS pulse width to reset the watchdog 400 tRST Reset time out 100 tWDO REV 1.1 9/25/00 Parameter www.xicor.com ns 200 300 Characteristics subject to change without notice. ms 14 of 20 X5083 VTRIP Programming Timing Diagram VCC (VTRIP) VTRIP tTHD tTSU VP VPE tVPS tVPH tPCS tVPO CS tRP SCK SI 06h 02h 0001h or 0003h VTRIP Programming Parameters Parameter Description Min. Max. Unit tVPS VTRIP program enable voltage setup time 1 µs tVPH VTRIP program enable voltage hold time 1 µs tPCS VTRIP programming CS inactive time 1 µs tTSU VTRIP setup time 1 µs tTHD VTRIP hold (stable) time 10 ms tWC VTRIP write cycle time tVPO VTRIP program enable voltage off time (between successive adjustments) 0 µs tRP VTRIP program recovery period (between successive adjustments) 10 ms VP Programming voltage 15 18 V VTRIP programmed voltage range 1.7 5.0 V Vta1 Initial VTRIP program voltage accuracy (VCC applied–VTRIP) (programmed at 25°C) -0.1 +0.4 V Vta2 Subsequent VTRIP program voltage accuracy [(VCC applied–Vta1)—VTRIP. Programmed at 25°C.) -25 +25 mV Vtr VTRIP program voltage repeatability (Successive program operations. Programmed at 25°C.) -25 +25 mV Vtv VTRIP program variation after programming (0-75°C). (programmed at 25°C) -25 +25 mV VTRAN 10 ms VTRIP programming parameters are periodically sampled and are not 100% tested. REV 1.1 9/25/00 www.xicor.com Characteristics subject to change without notice. 15 of 20 X5083 PACKAGING INFORMATION 8-Lead Plastic Dual In-Line Package Type P 0.430 (10.92) 0.360 (9.14) 0.260 (6.60) 0.240 (6.10) Pin 1 Index Pin 1 0.300 (7.62) Ref. Half Shoulder Width On All End Pins Optional 0.145 (3.68) 0.128 (3.25) Seating Plane 0.025 (0.64) 0.015 (0.38) 0.065 (1.65) 0.045 (1.14) 0.150 (3.81) 0.125 (3.18) 0.110 (2.79) 0.090 (2.29) .073 (1.84) Max. 0.060 (1.52) 0.020 (0.51) 0.020 (0.51) 0.016 (0.41) 0.325 (8.25) 0.300 (7.62) 0° 15° Typ. 0.010 (0.25) NOTE: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH REV 1.1 9/25/00 www.xicor.com Characteristics subject to change without notice. 16 of 20 X5083 PACKAGING INFORMATION 8-Lead Plastic Small Outline Gull Wing Package Type S 0.150 (3.80) 0.228 (5.80) 0.158 (4.00) 0.244 (6.20) Pin 1 Index Pin 1 0.014 (0.35) 0.019 (0.49) 0.188 (4.78) 0.197 (5.00) (4X) 7° 0.053 (1.35) 0.069 (1.75) 0.004 (0.19) 0.010 (0.25) 0.050 (1.27) 0.010 (0.25) X 45° 0.020 (0.50) 0.050" Typical 0.050" Typical 0° - 8° 0.0075 (0.19) 0.010 (0.25) 0.250" 0.016 (0.410) 0.037 (0.937) 0.030" Typical 8 Places FOOTPRINT NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) REV 1.1 9/25/00 www.xicor.com Characteristics subject to change without notice. 17 of 20 X5083 PACKAGING INFORMATION 8-Lead Plastic, TSSOP, Package Type V .025 (.65) BSC .169 (4.3) .252 (6.4) BSC .177 (4.5) .114 (2.9) .122 (3.1) .047 (1.20) .0075 (.19) .0118 (.30) .002 (.05) .006 (.15) .010 (.25) Gage Plane 0° – 8° Seating Plane .019 (.50) .029 (.75) (4.16) (7.72) Detail A (20X) (1.78) .031 (.80) .041 (1.05) (0.42) (0.65) All Measurements Are Typical See Detail “A” NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) REV 1.1 9/25/00 www.xicor.com Characteristics subject to change without notice. 18 of 20 X5083 Ordering Information VTRIP Range Package 4.5-5.5V 4.5.4.75 8-Pin PDIP 0–70°C X5083P-4.5A 8L SOIC 0–70°C X5083S8-4.5A -40–85°C X5083S8I-4.5A 8-Pin PDIP 0–70°C X5083P 8L SOIC 0–70°C X5083S8 -40–85°C X5083S8I 8L TSSOP 0–70°C X5083V8 8L SOIC 0–70°C X5083S8-2.7A 4.5-5.5V 2.7-5.5V 2.7-5.5V 1.8-3.6V 4.25.4.5 2.85-3.0 2.55-2.7 1.7-1.8 Operating Temperature Range Part Number RESET (Active LOW) VCC Range -40–85°C X5083S8I-2.7A 8L TSSOP 0–70°C X5083S8-2.7A 8L SOIC 0–0°C X5083S8-2.7 -40–85°C X5083S8I-2.7 8L TSSOP 0–70°C X5083V8-2.7 8L SOIC 0–70°C X5083S8-1.8 8L TSSOP 0–70°C X5083V8-1.8 Part Mark Convention 8-Lead SOIC/PDIP 8-Lead TSSOP X5083/85 X XX EYWW XXXXX 583AG = 1.8 to 3.6V, 0 to +70°C, VTRIP = 1.7-1.8V 583AH = 1.8 to 3.6V, -40 to +85°C, VTRIP = 1.7-1.8V 583F = 2.7 to 5.5V, 0 to +70°C, VTRIP = 2.55-2.7V 583G = 2.7 to 5.5V, -40 to +85°C, VTRIP = 2.55-2.7V 583AN = 2.7 to 5.5V, 0 to +70°C, VTRIP = 2.85-3.0V 583AP = 2.7 to 5.5V, -40 to +85°C, VTRIP = 2.85-3.0V X583 = 4.5 to 5.5V, 0 to +70°C, VTRIP = 4.25-4.5V 583I = 4.5 to 5.5V, -40 to +85°C, VTRIP = 4.25-4.5V 583AL = 4.5 to 5.5V, 0 to +70°C, VTRIP = 4.5-4.75V 583AM = 4.5 to 5.5V, -40 to +85°C, VTRIP = 4.5-4.75V AG = 1.8 to 3.6V, 0 to +70°C, VTRIP = 1.7-1.8V AH = 1.8 to 3.6V, -40 to +85°C, VTRIP = 1.7-1.8V F = 2.7 to 5.5V, 0 to +70°C, VTRIP = 2.55-2.7V G = 2.7 to 5.5V, -40 to +85°C, VTRIP = 2.55-2.7V AN = 2.7 to 5.5V, 0 to +70°C, VTRIP = 2.85-3.0V AP = 2.7 to 5.5V, -40 to +85°C, VTRIP = 2.85-3.0V Blank = 4.5 to 5.5V, 0 to +70°C, VTRIP = 4.25-4.5V I = 4.5 to 5.5V, -40 to +85°C, VTRIP = 4.25-4.5V AL = 4.5 to 5.5V, 0 to +70°C, VTRIP = 4.5-4.75V AM = 4.5 to 5.5V, -40 to +85°C, VTRIP = 4.5-4.75V YWW = year/work week device is packaged. REV 1.1 9/25/00 www.xicor.com Characteristics subject to change without notice. 19 of 20 X5083 LIMITED WARRANTY ©Xicor, Inc. 2000 Patents Pending Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Xicor, Inc. makes no warranty of merchantability or fitness for any purpose. Xicor, Inc. reserves the right to discontinue production and change specifications and prices at any time and without notice. Xicor, Inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a Xicor, Inc. product. No other circuits, patents, or licenses are implied. TRADEMARK DISCLAIMER: Xicor and the Xicor logo are registered trademarks of Xicor, Inc. AutoStore, Direct Write, Block Lock, SerialFlash, MPS, and XDCP are also trademarks of Xicor, Inc. All others belong to their respective owners. U.S. PATENTS Xicor products are covered by one or more of the following U.S. Patents: 4,326,134; 4,393,481; 4,404,475; 4,450,402; 4,486,769; 4,488,060; 4,520,461; 4,533,846; 4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829,482; 4,874,967; 4,883,976; 4,980,859; 5,012,132; 5,003,197; 5,023,694; 5,084,667; 5,153,880; 5,153,691; 5,161,137; 5,219,774; 5,270,927; 5,324,676; 5,434,396; 5,544,103; 5,587,573; 5,835,409; 5,977,585. Foreign patents and additional patents pending. LIFE RELATED POLICY In situations where semiconductor component failure may endanger life, system designers using this product should design the system with appropriate error detection and correction, redundancy and back-up features to prevent such an occurrence. Xicor’s products are not authorized for use in critical components in life support devices or systems. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. REV 1.1 9/25/00 www.xicor.com Characteristics subject to change without notice. 20 of 20