MIMIX XR1008-QB-0L00

35.0-45.0 GHz GaAs Receiver
SMT, 7x7 mm
R1008-QB
January 2008 - Rev 24-Jan-08
Features
Sub-harmonic, Image Reject Receiver
Integrated LNA, Image Reject Mixer, LO Doubler/Buffer
+2.0 dBm LO Drive Level
8.0 dB Conversion Gain
3.5 dB NF
+5.0 dBm Input Third Order Intercept (IIP3)
7x7mm SMT package
100% RF and DC Testing
General Description
Mimix Broadband’s 35.0-45.0 GHz packaged receiver has a
noise figure of 3.5 dB and 5.0 dBm Input Third Order
Intercept across the band. This device integrates a three
stage LNA followed by an image reject resistive pHEMT
mixer and includes an integrated LO doubler and buffer
amplifier. The use of integrated LO doubler and LO buffer
amplifier makes the provision of the LO easier than for
fundamental mixers at these frequencies. I and Q mixer
outputs are provided and an external 90 degree hybrid is
required to select the desired sideband. The device comes
in a 7x7mm SMT package that is RoHS compliant. This
device is well suited for Millimeter-wave Point-to-Point
Radio, LMDS, SATCOM and VSAT applications.
Absolute Maximum Ratings
Supply Voltage (Vd)
Supply Current (Id)
Gate Bias Voltage (Vg)
Input Power (Pin)
Storage Temperature (Tstg)
Operating Temperature (Ta)
Channel Temperature (Tch)
ESD - Human Body Model
ESD - Machine Body Model
+6.0 VDC
300 mA
+0.3 VDC
+5 dBm
-65 to +165 deg C
-55 to MTTF Table1
MTTF Table1
Class 1A
Class M1
(1) Channel temperature affects a device’s MTTF. It is
recommended to keep channel temperature as low as
possible for maximum life
Electrical Characteristics (Ambient Temperature T = 25o C)
Parameter
Frequency Range (RF)
Frequency Range (LO)
Frequency Range (IF)
Input Return Loss RF (S11)
Small Signal Conversion Gain RF/IF (S21)
LO Input Drive (PLO)
Image Rejection
Noise Figure (NF)
Isolation LO/RF @ LOx1/LOx2
Input Third Order Intercept (IIP3)
Input 1 dB Compression (IP1dB)
Drain Bias Voltage (Vd)
Gate Bias Voltage (Vg1,2)
Supply Current (Id) (Vd=4.0, Vg=-0.5V Typical)
Units
GHz
GHz
GHz
dB
dB
dBm
dBc
dB
dB
dBm
dBm
VDC
VDC
mA
Min.
35.0
16.0
DC
-1.2
-
Typ.
10.0
8.0
+2.0
20.0
3.5
40.0/40.0
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
+5.0
-5.0
+4.0
-0.5
180
Max.
45.0
24.0
4.0
+5.5
+0.1
240
Page 1 of 7
Characteristic Data and Specifications are subject to change without notice. ©2008 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
35.0-45.0 GHz GaAs Receiver
SMT, 7x7 mm
R1008-QB
January 2008 - Rev 24-Jan-08
Measurements
XR1008-QB: USB Conv. Gain and Image Rej. Vs Freq.
Vd=4V, Id=180mA, P_LO=+2dBm
20
15
Con.Gain(dB) and IR (dBc)
10
5
0
Gain
-5
IR
-10
-15
-20
-25
-30
35
36
37
38
39
40
41
RF (GHz) [IF=2GHz]
42
43
44
45
XR1008-QB: LSB Conv. Gain and Image Rej. Vs Freq.
Vd=4V, Id=180mA, P_LO=+2dBm
20
Con.Gain(dB) and IR (dBc)
15
10
5
0
Gain
-5
IR
-10
-15
-20
-25
-30
35
36
37
38
39
40
41
RF (GHz) [IF=2GHz]
42
43
44
45
XR1008-QB: Noise Figure (dB) vs Freq (GHz)
Vd=4V, Id=180mA, P_LO=+4dBm
10.0
9.0
USB
LSB
8.0
NF(dB)
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0.0
35
36
37
38
39
40
RF (GHz) [IF=2GHz]
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 2 of 7
Characteristic Data and Specifications are subject to change without notice. ©2008 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
35.0-45.0 GHz GaAs Receiver
SMT, 7x7 mm
R1008-QB
January 2008 - Rev 24-Jan-08
Physical Dimensions
QB - MSL, Gross Leak Test Compliant
(Note: Engineering designator is 40REC0770)
Functional Schematic
VD
28
27
GND IF1
GND
26
24
25
Pin Designations
23
GND
GND
RF IN
GND
Pin Function
Nominal
Value
3
Image
Reject
Mixer
LNA
4
LO
Buffer
x2
5
180
6
19
GND
18
LO IN
17
GND
16
in > 1
7
15
8
VG1
LNA, LO Amp
-0.5 V
9
VG2
Mixer, Doubler
-0.5 V
10
11
12
17
18
19
24
25
26
27
All other
pins
GND
IF2
GND
GND
LO IN
GND
GND
IF1
GND
VD
8
VG1
9
10
VG2 GND
11
12
IF2
GND
13
NC
Remarks
Ground
RF Input
Ground
20
2
RF IN
Pin Name
21
1
GND
Pin
Number
3
4
5
22
Ground
IF2 Output
Ground
Ground
LO Input
Ground
Ground
IF1 Output
Ground
Drain Bias
Not
Connected
Adjust VG1 for drain
current (Id) = 180 mA.
VG1 has an input
impedance of 180 .
VG2 requires a fixed
voltage and has a high
input impedance > 1 M
+ 2 dBm
+ 4.0 V
14
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 3 of 7
Characteristic Data and Specifications are subject to change without notice. ©2008 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
35.0-45.0 GHz GaAs Receiver
SMT, 7x7 mm
R1008-QB
January 2008 - Rev 24-Jan-08
Recommended Layout
App Note [1] Biasing - Please refer to the functional block diagram and pin-out table for biasing information. The device is operated by
biasing VD=4.0V with ID=180 mA by adjusting the applied voltage on VG1. VG1 typically requires-0.5V to result in the drain current being
180mA. The nominal input impedance of this gate is 180Ohm, so it should be noted that the nominal gate current will be 2.7mA.
Additionally, a fixed bias of VG2=-0.5V is required to bias the mixer and doubler. Adjusting VG2 above or below this value can adversely affect
conversion gain, image rejection and intercept point performance. It is recommended to use active biasing to keep the currents constant as
the RF power and temperature vary; this gives the most reproducible results. The diagram “Active Bias Circuit” demonstrates a possible
method for active biasing. Depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single
transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the current. The gate of
the pHEMT is controlled to maintain correct drain current and thus drain voltage. Typically the gate is protected with Silicon diodes to limit
the applied voltage. Also, make sure to sequence the applied voltage to ensure negative gate bias is available before applying the positive
drain supply
Active Bias Circuit
5.0V
5k76
5R62 (sense)
4V, 180mA
Vd
3
4.0V
1
100n
2
MMBT3904
2
1
MMBT3906
10R
3
12k1
12k1
100R
-5.0V
1k0
Vg1
1
2
100n
3
BAV99
3
BAV99
2
1
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 4 of 7
Characteristic Data and Specifications are subject to change without notice. ©2008 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
35.0-45.0 GHz GaAs Receiver
SMT, 7x7 mm
R1008-QB
January 2008 - Rev 24-Jan-08
MTTF
MTTF is calculated from accelerated life-time data of single devices and assumes an isothermal back-plate.
MTTF (yrs) vs. Backplate Temperature (°C)
1.E+05
MTTF (Years)
1.E+04
1.E+03
1.E+02
1.E+01
1.E+00
55
65
75
85
95
Temperature (°C)
Bias Conditions: Vd=4.0V, Id=180 mA
Typical Application
BPF
XR1008-QB
IF Out
2 GHz
Coupler
RF IN
37.0-39.5 GHz
LNA
IR Mixer
Buffer
AGC Control
X2
LO(+2.0dBm)
17.5-18.75 GHz (USB Operation)
19.5-20.75 GHz (LSB Operation)
Mimix Broadband MMIC-based 35.0-45.0 GHz Receiver Block Diagram
(Changing LO and IF frequencies as required allows design to operate as high as 46 GHz)
Mimix Broadband's 30.0-46.0 GHz XR1008-QB GaAs MMIC Receiver can be used in saturated radio applications and linear modulation
schemes up to 128 QAM.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 5 of 7
Characteristic Data and Specifications are subject to change without notice. ©2008 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
35.0-45.0 GHz GaAs Receiver
SMT, 7x7 mm
R1008-QB
January 2008 - Rev 24-Jan-08
App Note [3] USB/LSB Selection -
LSB
USB
IF2
For Upper Side Band operation (USB):
With IF1 and IF2 connected to the
direct port (0º) and coupled port (90º)
respectively as shown in the diagram,
the USB signal will reside on the
isolated port. The input port must be
loaded with 50 ohms.
For Lower Side Band operation (LSB):
With IF1 and IF2 connected to the
direct port (0º) and coupled port (90º)
respectively as shown in the diagram,
the LSB signal will reside on the input
port. The isolated port must be loaded
with 50 ohms.
IF1
An alternate method of Selection of USB or LSB:
-90
USB
LSB
In Phase Combiner
In Phase Combiner
-90o
o
IF2
IF2
IF1
IF1
Factory Automation and Identification
Mimix
Designator
Package
Type
Number of
leads offered
W Tape
Width
P1 Component
Pitch
P0 Hole
Pitch
Reel
Diameter
Units
per Reel
-QB
QFN (7x7mm)
28
16mm
12mm
4mm
329mm (13in)
1000
Tape and Reel Packaging per the following conditions:
Tape Width:
16 mm
Tape Pitch (part to part):
12 mm
Component Orientation:
Parts are to be oriented with the PIN 1 closest to the tape's round sprocket holes on the tape’s trailing edge.
Reel Diameter:
329 mm (13 inch)
Note: Tape and Reel packaging is ordered with a -000T suffix. Package is available in 500 unit reels through designated sales channels.
Minimum order quantities should be discussed with your local sales representative.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 6 of 7
Characteristic Data and Specifications are subject to change without notice. ©2008 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
35.0-45.0 GHz GaAs Receiver
SMT, 7x7 mm
R1008-QB
January 2008 - Rev 24-Jan-08
CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the
environment. For safety, observe the following procedures:
Do not ingest.
Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these
by-products are dangerous to the human body if inhaled, ingested, or swallowed.
Observe government laws and company regulations when discarding this product. This product must be discarded in
accordance with methods specified by applicable hazardous waste procedures.
- Mimix Broadband's products are not authorized for use as critical components in life support devices or
systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life
support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain
life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be
reasonably expected to result in a significant injury to the user. (2) A critical component is any component of a life support device or
system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its
safety or effectiveness.
Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package compatible
with high volume solder installation. The package is a low-cost plastic package. Vacuum tools or other suitable pick and place
equipment may be used to pick and place this part. Care should be taken to ensure that there are no voids or gaps in the solder
connection so that good RF, DC and ground connections are maintained. Voids or gaps can eventually lead not only to RF
performance degradation, but reduced reliability and life of the product due to thermal stress.
Reflow Profile
Ramp Up Rate
Activation Time and Temperature
Time Above Melting Point
Max Peak Temperature
Time Within 5 ºC of Peak
Ramp Down Rate
SnPb
3-4 ºC/sec
60-120 sec @ 140-160 ºC
60-150 sec
240 ºC
10-20 sec
4-6 ºC/sec
Pb Free
3-4 ºC/sec
60-180 sec @ 170-200 ºC
60-150 sec
265 ºC
10-20 sec
4-6 ºC/sec
Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental
requirements for eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix RoHS compliant
components are form, fit and functional replacements for their non-RoHS equivalents. Lead plating of our RoHS compliant parts is
100% matte tin (Sn) over copper alloy and is backwards compatible with current standard SnPb low-temperature reflow processes as
well as higher temperature (260°C reflow) “Pb Free” processes.
Ordering Information
XR1008-QB-0L00
XR1008-QB-0L0T
XR1008-QB-EV1
Ni/Pd/Au plated RoHS compliant QFN 7x7 28L surface mount package in bulk quantity
Ni/Pd/Au plated RoHS compliant QFN 7x7 28L surface mount package in tape and reel
XR1008-QB Evaluation Module
We also offer this part with alternative plating options. Please contact your regional sales manager for more information regarding
different plating types.
Caution: ESD Sensitive
Appropriate precautions in handling, packaging
and testing devices must be observed.
Proper ESD procedures should be followed when handling this device.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 7 of 7
Characteristic Data and Specifications are subject to change without notice. ©2008 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.