NKK YB225CWCKW01-5D-JB

Toggles
Series YB2
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Keylocks
Programmable Illuminated PB
Pushbuttons
Power Level (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC
Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Other Ratings
D
Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: Bezel:
Housing:
Base:
Movable Contactor:
Movable Contacts:
Stationary Contacts:
Switch Terminals:
Lamp Terminals:
Environmental Data
Touch
Operating Temperature Range: Humidity: Vibration: Shock: Sealing: Installation
Indicators
Tilt
Tactiles
Slides
Rotaries
Materials & Finishes
Standards & Certifications
50 milliohms maximum for silver; 100 milliohms maximum for gold
200 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
1,000,000 operations minimum for momentary circuit
200,000 operations minimum for maintained circuit
100,000 operations minimum
Single pole: 1.5N
Double pole: 3.0N
Nonshorting (break-before-make)
Pretravel .059” (1.5mm); Overtravel .059” (1.5mm); Total Travel .118” (3.0mm)
Black: Glass fiber reinforced polyamide (UL94V-0); Silver: Polycarbonate
Glass fiber reinforced polyamide (UL94V-0)
Diallyl phthalate resin (UL94V-0)
Phosphor bronze with silver or gold plating
Phosphor bronze & silver alloy
Silver alloy or copper with gold plating
Phosphor bronze with tin plating
Phosphor bronze with tin plating
–25°C through +50°C (–13°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
IP65 of IEC60529 standard
Mounting Torque: 0.785Nm (6.95 lb•in) maximum
Soldering Time & Temperature: Manual Soldering: 390°C maximum for 4 seconds maximum
Flammability Standards:
UL:
UL94V-0 housing, base & black or metallic silver bezel
File No. E44145
All solder lug models recognized at 3A @ 125/250V AC or 0.4VA @ 28V AC/DC maximum.
Add “/CUL” to end of part number to order cULus mark on switch.
Supplement
Accessories
22mm Panel Seal Pushbuttons
D114
www.nkk.com
Toggles
Series YB2
Rockers
Distinctive Characteristics
Pushbuttons
22mm pushbutton with the shortest above-panel dimension (1.8mm) in the industry
for splashproof design.
Meets IP65 of IEC60529 standards (similar to NEMA 4 and 13), providing
dust tight and splashproof panel seal protection.
Tamper resistant 19mm diameter actuator.
D
Short body of .965” (24.5mm) conserves behind-panel
space.
Keylocks
Distinctive long stroke and light touch actuation for clear
indication of circuit status.
Programmable Illuminated PB
22mm Panel Seal Pushbuttons
Rotaries
Choice of cap colors includes clear, red, green, amber,
or metallic silver for enhanced panel appearance.
Metallic silver cap option has bright ring illumination.
Slides
Brilliant illumination with multiple LED colors.
Tactiles
Bezel color options in silver or black.
Available in momentary and alternate action with latchdown.
Actual Size
Touch
Combination solder lug and .110” quick connect terminals. Terminals
are epoxy sealed to lock out flux, dust, solvents, and other contaminants,
as well as to secure terminals and improve contact stability.
Tilt
Crisp actuation and clear circuit status provided by snap-action
contact mechanism. Arc barrier protects against crossover.
Supplement
Accessories
Indicators
Custom legends on actuator available.
www.nkk.com
D115
Series YB2
Toggles
Toggles
22mm Panel Seal Pushbuttons
1
C
W
C
K
W
01
6 F
JB
LEDS
Cap Types & Colors
Bright LED
Lens/Diffuser Colors
C
Round
01
LED Colors
Circuits
5
ON
Panel Seal
W
(ON)
With Panel Seal
( ) = Momentary
Rotaries
6
ON
Bezel
K
Black
S
Metallic Silver
W
Silver
Rated 3A @ 125V AC
G
Gold
Rated 0.4VA maximum @
28V AC/DC maximum
ON
Slides
Alternate Action
with Latchdown
* Wire harness & cable assemblies offered only in Americas
IMPORTANT:
Switches are supplied without
cULus marking unless specified.
Specific models & ratings noted
on General Specifications page.
No
Code
5C
Red
5D
Amber
5F
Green
No Resistor
(not for
Green)
05
5-volt
12
12-volt
24
24-volt
JB
Clear/White
JS
Metallic Silver Cap/Clear Ring
CB
Red/White
EB
Yellow/White
FB
Green/White
LED & cap need to be the same color.
Yellow cap pairs with amber LED to achieve
amber illumination. Codes JB & JS may
be combined with all LED colors.
Super Bright LED
Lens/Diffuser Cap Colors
6B
White
JB
Clear/White
6F
Green
JS
Metallic Silver Cap/Clear Ring
6G
Blue
N
No Lamp
S
Metallic Silver
JB
Clear/White
CB
Red/White
EB
Yellow/White
FB
Green/White
Nonilluminated
Tilt
Tactiles
Contact Materials
& Ratings
Resistor
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Cap Color
Touch
Touch
YB215CWCKW01-6F-JB
D
Programmable Illuminated PB
DPDT
Normally Open and
Normally Closed
Keylocks
2
C
Rotaries
SPDT
Terminals
Solder Lug/.110”
(2.8mm) Quick Connect*
Slides
1
Shape
Tactiles
Contact Point
Tilt
Poles
D
Keylocks
Programmable Illuminated PB
Pushbuttons
5
Pushbuttons
Rockers
YB2
Rockers
TYPICAL SWITCH ORDERING EXAMPLE
Accessories
Round Black Housing
SPDT
ON-(ON) Circuit
Indicators
Black Bezel
LED Cap with Clear Lens
& White Diffuser
With Panel Seal
Accessories
Indicators
Green, Super Bright LED
Silver Contacts with
3 Amp Rating
D116
www.nkk.com
Supplement
Supplement
Solder Lug/.110” (2.8mm)
Quick Connect Terminals
www.nkk.com
D117
Series YB2
Toggles
22mm Panel Seal Pushbuttons
POLES & CIRCUITS
D
Connected Terminals
Throw & Switch/Lamp Schematics
Notes: Switch is marked with NC, NO, COM, L+, L–.
Lamp circuit is isolated and requires an
external power source.
Normal
Down
Normal
Down
YB215
YB216
ON
ON
(ON)
ON
1-3
1-2
SPDT
YB225
YB226
ON
ON
(ON)
ON
1-3 4-6
1-2 4-5
DPDT
Pole
Model
SP
DP
1 (COM)
3 NC
3 NC
C
(COM)
2 NO
W
Normally Open and Normally Closed
6 NC
L (+)
(-) L
4
5 NO
Panel Seal
Rotaries
Two o-rings provide
panel seal protection
meeting IP65 of
IEC60529 standards.
SHAPE
BEZEL
Round
K
Black
S
Metallic Silver
Tilt
Tactiles
Slides
(-) L
PANEL SEAL
Contact points are both Normally Open and
Normally Closed.
C
L (+)
2 NO
1
CONTACT POINT
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
Plunger Position
( ) = Momentary
W
G
Silver Contacts
01
D118
Gold Contacts
Power Level: 3A @ 125/250V AC
Logic Level: 0.4VA max. @ 28V AC/DC max.
Switch base is green
Switch base is red
TERMINALS
Supplement
Accessories
Indicators
Touch
CONTACT MATERIALS & RATINGS
Solder Lug/
.110” (2.8mm) Quick Connect
Epoxy Seal
(7.3)
.288
(2.0)
(2.8)
.079
.110
(1.2)
.047
Thk = (0.5)
.020
www.nkk.com
Toggles
Series YB2
BRIGHT & SUPER BRIGHT LEDS
Rockers
The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and
requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required.
Base of AT634 and AT636 is Black for 5V, Light Blue for 12V and Gray for 24V.
Electrical Specifications for Bright LED without Resistor
5C
Red
5D
No Code
Amber
LED Colors
T-1 Bi-pin
(+)
(-)
No Resistor
Unit
Red
Amber
Forward Peak Current
IFM
40
40
mA
Continuous Forward Current
IF
26
26
mA
Forward Voltage
VF
1.9
2.0
V
Reverse Peak Voltage
VRM
4
4
V
Current Reduction Rate Above 25°C
∆IF
Ambient Temperature Range
Pushbuttons
Colors
Available:
D
0.50
mA/°C
–25 ~ +50
°C
T-11⁄4 Bi-pin
5C
Red
5D
Amber
05
12
24
Unit
Forward Peak Current
IFM
—
—
—
mA
Continuous Forward Current
IF
25
20
10
mA
Forward Voltage
VF
5
12
24
V
Reverse Peak Voltage
VRM
4
8
16
V
Current Reduction Rate Above 25°C
∆IF
—
—
­­—
mA/°C
Ambient Temperature Range
AT634
5-volt,
(+)
2-element
with Resistor
AT634
12-volt,
4-element
with Resistor
(-)
–25 ~ +50
(+)
°C
AT634
(+)
24-volt,
4-element
with Resistor
(-)
Rotaries
Colors
Available:
Slides
Bright
AT634
Keylocks
Electrical Specifications for Bright Red & Amber LED with Resistor
(-)
(-)
(+)
5V
(-)
(+)
12V & 24V
5F
Green
05
12
24
Unit
Forward Peak Current
IFM
—
—
—
mA
Continuous Forward Current
IF
11
9.5
8.7
mA
Forward Voltage
VF
5
12
24
V
Reverse Peak Voltage
VRM
5
5
5
V
Current Reduction Rate Above 25°C
∆IF
—
—
­­—
mA/°C
ELECTROSTATIC
SENSITIVE DEVICES
Ambient Temperature Range
–25 ~ +50
Tilt
T-11⁄4 Bi-pin
ATTENTION
Tactiles
Electrical Specifications for Bright Green LED with Resistor
Colors
Available:
Bright
AT636
Programmable Illuminated PB
Bright
AT628
°C
Touch
22mm Panel Seal Pushbuttons
T-1 Bi-pin
(+)
(-)
Colors:
6B
6F
6G
White
Green
Blue
Unit
Forward Peak Current
IFM
30
30
30
mA
Continuous Forward Current
IF
20
20
20
mA
Forward Voltage
VF
3.6
3.5
3.6
V
Reverse Peak Voltage
VRM
5
5
5
V
Current Reduction Rate Above 25°C
∆IF
Ambient Temperature Range
www.nkk.com
Accessories
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
0.50
mA/°C
–25 ~ +50
°C
D119
Supplement
Super Bright
AT625G Blue
AT631B White
AT632F Green
Indicators
Electrical Specifications for Super Bright LED
Series YB2
Toggles
22mm Panel Seal Pushbuttons
BALLAST RESISTOR CALCULATION FOR LEDS
Rockers
Pushbuttons
Programmable Illuminated PB
IF
+
R =
Anode
Where: R =
E =
VF =
IF =
VF
E
Cathode
–
E – VF
IF
Resistor Value (Ohms)
Source Voltage (V)
Forward Voltage (V)
Forward Current (A)
CAPS & CAP COLORS
D
AT3017 Cap for
Bright LED
AT3018 Cap for
Super Bright LED
AT3019 Cap for
Nonilluminated
AT3020 Cap with
Illumination Ring for
Bright or Super Bright LED
Lens/Diffuser Colors Available:
Lens/Diffuser Colors Available:
Cap Color Available:
Cap Color Available:
Keylocks
Rotaries
Slides
Tactiles
R
If the source voltage is greater than the rated voltage of
a lamp or LED, a ballast resistor must be connected in
series with the lamp. This circuit diagram and formula
will assist in calculating the value of the required ballast
resistor.
JB
Clear/White
CB
Red/White
EB
* Yellow/White
FB
Green/White
JB
S
Clear/White
(19.0) Dia
.748
*Yellow cap
pairs with amber LED
to achieve amber illumination.
(4.9)
.193
Metallic Silver with
Clear Ring
Note: AT3017 Cap can
also be used without illumination.
(19.0) Dia
.748
(4.9)
.193
JS
Metallic Silver
(19.0) Dia
.748
(13.1)
.516
(4.9)
.193
(19.0) Dia
.748
(13.1)
.516
(4.9)
.193
(13.1)
.516
(13.1)
.516
Materials
Lens: Polycarbonate
Insert: Polyester
Material for Lens & Diffuser: Polycarbonate
TYPICAL SWITCH DIMENSIONS
Single Pole
(3.7)
.146
(1.2) x (2.0) Typ
.047 x .079
M16 P1
Double Pole
(3.7)
.146
(0.5) Typ
.020
L
2
3
NO
NO
Tilt
NC
1
(19.0) Dia
.748
(25.0) Dia
.984
COM
(3.0)
.118
(7.3)
.288
(1.8)
.071
(33.6)
1.323
(5.55)
.219
PANEL THICKNESS & CUTOUT
(25.4) Min
1.00
Panel Thickness
.020” ~ .197”
(0.5mm ~ 5.0mm)
0.3
Dia Typ
(22.0) +– 0.0
.866
Supplement
(25.4) Min
1.00
(10.5)
.413
(1.7) Typ
.067
D120
www.nkk.com
Side-by-side Mounting
5
-+
1
YB215CWCKW01-6F-JB
Accessories
Indicators
Touch
(2.8) Typ
.110
6
L
2
- +
NC
COM
(6.0)
.236
(11.1)
.437
NO
3
NO
(9.7)
.382
4
(9.7)
.382
Series YB2
Toggles
22mm Panel Seal Pushbuttons
1. Remove knurled
mounting nut.
5. Install the red o-ring which
was removed in step 2 at
the inside bottom of the
bezel.
Rockers
ASSEMBLY INSTRUCTIONS
Red O-ring
2. Remove bezel and red
o-ring from housing.
There are two o-rings
in this assembly: one is
red, one is orange.
6. Align tab inside of the bezel with keyway on housing and
bring bezel back into its original position.
Housing
Bezel
Red O-ring
Bezel
LED AT628
D-Flat
(+)
Align D-flat on LED with Part Number
on switch for appropriate polarity and
insert LED into base.
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
Keylocks
Tab
8. Attach mounting nut behind panel and tighten. Make
sure that bezel and actuator fit properly and that there is
no space between bezel and panel. Do not overtighten.
Mounting torque: 0.785Nm (6.95 lb•in) maximum.
Optional socket wrench AT106 available.
Touch
The larger metal part within the LED
represents the cathode (–). Align LED
for appropriate polarity and insert LED
into base.
Rotaries
Keyway
Panel
Align D-flat on LED with Part Number
on switch for appropriate polarity and
insert LED into base.
(–)
LEDs AT625G,
AT631B,
AT632F
Bezel
Slides
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
Back of
Bezel
Tactiles
LEDs
AT634 & AT636
7. Before installing into panel,
make sure that the orange
o-ring is present at the back
of the bezel. Align keyway
on bezel with tab in panel
and push switch all the way
into the panel.
Tilt
Anode
Socket (+)
(–)
Tab
Cathode
Socket (–)
3. Install LED.
D-Flat
Orange
O-ring
Red
O-ring
Part Number
This Side
(+)
D
Keyway
Programmable Illuminated PB
Knurled
Mounting Nut
Pushbuttons
Bezel
(–)
Cathode (–)
Anode (+)
Bezel
Indicators
Actuator
(+)
Panel
Actuator
Accessories
B
Knurled
Mounting Nut
A
Housing
Supplement
4. Align tabs (B) on both
sides of actuator with
the projections (A) inside
of the housing and push
actuator firmly down to
snap in.
AT106 Socket Wrench
www.nkk.com
D121
Series YB2
Toggles
22mm Panel Seal Pushbuttons
LEGENDS
Rockers
NKK Switches can provide custom legends for caps. Contact factory for more information.
Shaded Area is Printable Area for Caps
Shaded Area is Printable Area for Cap
AT3017, AT3018 and AT3019
AT3020 (with clear ring for illumination)
D
(0.76) Typ
.030
(17.48) Dia
.688
(19.0) Dia
.748
Keylocks
Programmable Illuminated PB
Pushbuttons
Recommended Methods: Laser Etch on clear cap, Screen Print or Pad Print on cap.
Epoxy based ink is recommended.
(15.88) Dia
.625
(19.0) Dia
.748
(1.56) Typ
.062
Shaded Area is Printable Area for Film Inserts
Rotaries
(0.1) Typ
(1.2) +/–.0039
.047
(0.6) R Typ
.024
Film Material and Thickness:
Slides
(14.78)
.0031
.582 (16.3) +(0.08)
– (0.1) .0039
.642
(15.88)
.625
Clear Polyester, 4 mil max.
Recommended Print Method:
(0.76) Typ
.030
Screen Print; Epoxy based ink is recommended
+(0.08) .0031
Tactiles
(17.4) – (0.1) .0039
.685
HANDLING & PRECAUTIONS
Tilt
ATTENTION
LEDs are electrostatic sensitive devices. When installing and handling LEDs, use an electrostatic
protected work station to prevent LED damage.
Supplement
Accessories
Indicators
Touch
ELECTROSTATIC
SENSITIVE DEVICES
D122
www.nkk.com