ZAMP002 800-2500MHz MMIC WIDEBAND AMPLIFIER Medium Power, 22dB Gain, Wide Dynamic Range DESCRIPTION The ZAMP002 is an low current high performance RF amplifier designed for L band and IF applications. Although the ZAMP002 has been designed primarily for DBS applications the ZAMP002 is capable of extending to frequencies of 2.5GHz so it has a good fit with various applications. An additional benefit of the ZAMP002 is it’s rising gain characteristic, this has been designed to counteract the gain losses found at the higher frequencies. The ZAMP002 has been optimized to an input impedance of 50ohms while the output impedance has been designed for optimum match to an impedance of 75ohms. Packaged in a small SC70-6 w i th the m i ni m um num ber of e x t e r n a l b i a s components required it is the ideal solution for space and current limited applications. SC70-6 FEATURES CONNECTION DIAGRAM • L and IF frequency band Top View • Low noise • Low current consumption 21mA typical • Gain 22dB typical GND 1 6 OUTPUT GND 2 5 GND INPUT 3 • Rising gain across band 4 VCC • IP3 22dBm @ 1GHz • 4.5 to 5.5V supply voltage • SC70-6 SMD package APPLICATIONS • Satellite LNB receivers • RF buffers - tuners ORDERING INFORMATION DEVICE • SMR (Special Mobile Radio) REEL SIZE (inches) QUANTITY PER REEL DEVICE MARKI NG • RLAN/WLAN ZAMP002H6TA 7” 3000 units ZB02 • General purpose ZAMP002H6TC 13” 10000 units ZB02 ISSUE 2 - MARCH 2003 1 SEMICONDUCTORS ZAMP002 ABSOLUTE MAXIMUM RATINGS Supply Voltage Supply Current Operating Temperature Storage Temperature 7V 30mA -40 to 85°C -50 to 125°C ELECTRICAL CHARACTERISTICS Test Conditions (unless otherwise stated): VCC = 5V, Tamb = 25°C, Zo = 50⍀. SYMBOL PARAMETER CONDITIONS MIN FO Operating Frequency 800 V CC Supply Voltage 4.5 I CC Supply Current Gp Power Gain NF Noise Figure F = 950 MHz 21 P1dB 1dB Gain Compression RL IN Input Return Loss RL OUT Output Return Loss Risol Reverse Isolation UNITS 2500 MHz 5 5.5 21 24 V mA dB F = 1550 MHz 22 dB F = 2150 MHz 23 F = 950 MHz 6 dB 6.5 dB F = 2150 MHz 3rd Order Intercept Point MAX 22 F = 1550 MHz IP3 TYP. 25 dB 7 dB 22 dBm F = 2150 MHz 17 dBm F = 950 to 2150 MHz 7 dBm F = 950 MHz 16 dB F = 2150 MHz 17 dB F = 950 MHz 10 dB F = 2150 MHz 9 dB F = 950 MHz 30 dB F = 2150 MHz 33 dB F = 950 MHz 18 ISSUE 2 - MARCH 2003 SEMICONDUCTORS 2 ZAMP002 TYPICAL CHARACTERISTICS Test Conditions (unless otherwise stated): VCC = 5V, Tamb = 25°C, Zo = 50⍀. ISSUE 2 - MARCH 2003 3 SEMICONDUCTORS ZAMP002 TYPICAL CHARACTERISTICS ISSUE 2 - MARCH 2003 SEMICONDUCTORS 4 ZAMP002 TEST CIRCUIT Vcc C4 100nF X7R C3 C5 100pF NPO 100pF NPO L1 4 100nH J1 IC1 C1 3 C2 J2 6 100pF NPO 1 2 5 100pF NPO ZAMP002 CIRCUIT COMPONENTS LIST Circuit Ref. Description Value C1,C2,C3, C5 Chip ceramic capacitor 100 pF Type Murata GRH708 series, size 0805 C4 Chip ceramic capacitor 100 nF X7R, size 0805 L1 Chip inductor 100 nH IC1 ZAMP002 Murata LQW18ANR10G00D, size 0805 Wideband Amplifier, SC70-6 ISSUE 2 - MARCH 2003 5 SEMICONDUCTORS ZAMP002 TEST CIRCUIT LAYOUT APPLICATION NOTES An example layout for a test board for the ZAMP series can be seen above. This was designed for an FR4 board 1 x 1 inch, 0.016 inch thick with a copper thickness of 35 microns. Edge mounted SMA connectors were used for the RF signals. The ZAMP002 is a wideband RFIC amplifier designed for use primarily in DBS applications. The amplifier is designed to provide a 50 Ohm input and 75 Ohm output and thus requires no additional matching components. The input and output signal connections each require a DC blocking capacitor (C1 and C2). A suitable value for these capacitors is 100pF for the 950MHz to 2150MHz frequency range. For other frequency ranges the value of the capacitor should be such that its reactance at the lowest operating frequency is small when compared to 50 ohms (or 75 Ohms for the output). Supply de-coupling is also recommended and should take the form of a suitable 100pF capacitor, C3, for the 950MHz to 2150MHz frequency range. The 100pF capacitor should be mounted as close to the Vcc pin of the amplifier as is physically possible. An additional low frequency de-coupling capacitor, C4, with a value of 100nF is also advised. The ZAMP002 requires a RF choke inductor, L1, providing DC bias to the output line. A value of 100nH is recommended for the 950 MHz to 2150MHz frequency range. ISSUE 2 - MARCH 2003 SEMICONDUCTORS 6 ZAMP002 Notes ISSUE 2 - MARCH 2003 7 SEMICONDUCTORS ZAMP002 PACKAGE DIMENSIONS SC706 PACKAGE DIMENSIONS MILLIMETRES DIM MIN MAX MILLIMETRES DIM MIN MAX A ᎏ 1.00 E A1 ᎏ 0.10 E1 A2 0.70 0.90 e b 0.15 0.30 e1 C 0.08 0.25 L 0.26 0.46 ⍜ 0⬚ 8⬚ D 2.00 BSC 2.10 BSC 1.25 1.35 0.65 BSC 1.30 BSC © Zetex plc 2003 Americas Asia Pacific Zetex GmbH Streitfeldstraße 19 D-81673 München Zetex Inc 700 Veterans Memorial Hwy Hauppauge, NY 11788 Germany Telefon: (49) 89 45 49 49 0 Fax: (49) 89 45 49 49 49 [email protected] USA Telephone: (1) 631 360 2222 Fax: (1) 631 360 8222 [email protected] Zetex (Asia) Ltd 3701-04 Metroplaza Tower 1 Hing Fong Road Kwai Fong Hong Kong Telephone: (852) 26100 611 Fax: (852) 24250 494 [email protected] Europe Zetex plc Fields New Road Chadderton Oldham, OL9 8NP United Kingdom Telephone (44) 161 622 4444 Fax: (44) 161 622 4446 [email protected] These offices are supported by agents and distributors in major countries world-wide. This publication is issued to provide outline information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose or form part of any order or contract or be regarded as a representation relating to the products or services concerned. The Company reserves the right to alter without notice the specification, design, price or conditions of supply of any product or service. For the latest product information, log on to www.zetex.com ISSUE 2 - MARCH 2003 SEMICONDUCTORS 8