STMicroelectronics AN2352 Pll jitter effects on c-can modules of the st10f27x Datasheet

AN2352
Application note
PLL jitter effects on C-CAN modules of the ST10F27x
Introduction
PLL (Phase Locked Loop) is increasingly used in microcontrollers to achieve higher internal
clock frequencies. This improves performance while reducing overall noise. One drawback
in the use of PLL circuits is that they create a small but still measurable level of transient
phase shifts, or jitter. The aim of this note is to describe the effects of PLL jitter on the CCAN modules present in the devices of the family ST10F27x.
This document begins with a brief guide on configuring the bit time of the CAN protocol and
then goes on to cover the characteristics of the PLL as implemented in the ST10F27x. The
last section shows the results of the effect of the ST10F27x PLL on the C-CAN.
The information contained in this document is valid for the ST10F27x, ST10R27x,
ST10F25x and ST10F296 devices.
September 2013
Rev 2
1/20
www.st.com
Contents
AN2352
Contents
1
2
Configuration of the CAN bit timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1
Bit time and bit rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2
Propagation time segment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3
Phase buffer segments and synchronization . . . . . . . . . . . . . . . . . . . . . . . 5
1.4
System clock tolerance range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.5
Configuration of the CAN protocol controller . . . . . . . . . . . . . . . . . . . . . . 10
1.6
Calculation of the bit timing parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2
2/20
1.6.2
Example for bit timing at low baud rate . . . . . . . . . . . . . . . . . . . . . . . . . 14
PLL jitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1.1
Jitter in the input clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1.2
Noise in the PLL loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ST10F27x PLL jitter effect in CAN protocol . . . . . . . . . . . . . . . . . . . . . 17
3.1
4
Example for bit timing at high baud rate . . . . . . . . . . . . . . . . . . . . . . . . 13
Phase locked loop (PLL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1
3
1.6.1
System clock tolerance range reduction in presence of PLL jitter . . . . . . 17
3.1.1
Range reduction percentage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1.2
Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
AN2352
1
Configuration of the CAN bit timing
Configuration of the CAN bit timing
Even if minor errors in the configuration of the CAN bit timing do not result in immediate
failure, the performance of a CAN network can be reduced significantly.
In many cases, the CAN bit synchronization compensates a faulty configuration of the CAN
bit timing to such a degree that an error frame is generated only occasionally. In the case of
arbitration however, when two or more CAN nodes simultaneously try to transmit a frame, a
misplaced sample point may cause one of the transmitters to become error passive.
The analysis of such sporadic errors requires a detailed knowledge of the CAN bit
synchronization inside a CAN node and of the CAN nodes’ interaction on the CAN bus.
1.1
Bit time and bit rate
CAN supports bit rates in the range of less than 1 Kbit/s up to 1000 Kbit/s. Each member of
the CAN network has its own clock generator, usually a quartz oscillator. The timing
parameter of the bit time (that is, the reciprocal of the bit rate) can be configured individually
for each CAN node, creating a common bit rate even though the CAN nodes’ oscillator
periods (fosc) may be different.
The frequencies of these oscillators are not absolutely stable. Small variations are caused
by changes in temperature or voltage and by deteriorating components. As long as the
variations remain within a specific oscillator tolerance range (df), the CAN nodes can
compensate the different bit rates by resynchronizing to the bit stream.
According to the CAN specifications, the bit time is divided into four segments (Figure 1):
●
Synchronization segment
●
Propagation time segment
●
Phase buffer segment 1
●
Phase buffer segment 2
Each segment consists of a specific, programmable number of time quanta (see Table 1).
The length of the time quantum (tq),which is the basic time unit of the bit time, is defined by
the CAN controller’s system clock fsys and the Baud Rate Prescaler (BRP):
tq = BRP / fsys
The C-CAN’s system clock fsys is the fCPU or fCPU / 2 according to bit 2 of the XMSIC
register.
The synchronization segment (Sync_Seg) is that part of the bit time where edges of the
CAN bus level are expected to occur; the distance between the Sync_Seg and an edge that
occurs outside of Sync_Seg is called the phase error of that edge. The propagation time
segment (Prop_Seg) is intended to compensate the physical delay times within the CAN
network. The phase buffer segments (Phase_Seg1 and Phase_Seg2) surround the sample
point. The (Re)synchronization jump width (SJW) defines how far a resynchronization may
move the sample point within the limits defined by the phase buffer segments to
compensate edge phase errors.
3/20
Configuration of the CAN bit timing
Figure 1.
AN2352
Bit timing
Nominal CAN bit time
Sync_ Prop_Seg
Seg
Phase_Seg1
1 Time quantum
( tq )
Phase_Seg2
Sample point
Table 1 describes the minimum programmable ranges required by the CAN protocol.
Table 1.
Parameters of the CAN bit time
Parameter
BRP
Range
[1 .. 32]
Remark
Defines the length of the time quantum tq
Sync_Seg
1 tq
Fixed length, synchronization of bus input to system clock
Prop_Seg
[1 .. 8] tq
Compensates the physical delay times
Phase_Seg1
[1 .. 8] tq
May be lengthened temporarily by synchronization
Phase_Seg2
[1 .. 8] tq
May be shortened temporarily by synchronization
SJW
[1 .. 4] tq
May not be longer than either phase buffer segment
A given bit rate may be met by different bit time configurations but for the proper functioning
of the CAN network, the physical delay times and the oscillator’s tolerance range must be
taken into consideration.
1.2
Propagation time segment
This part of the bit time compensates physical delay times within the network. These delay
times consist of the signal propagation time on the bus and the internal delay time of the
CAN nodes.
Any CAN node synchronized to the bit stream on the CAN bus will be out of phase with the
transmitter of that bit stream due to the signal propagation time between the two nodes. The
CAN protocol’s nondestructive bit-wise arbitration and the dominant acknowledge bit
provided by the receivers of CAN messages require a CAN node transmitting a bit stream to
also receive dominant bits transmitted by other CAN nodes that are synchronized to that bit
stream. The example in Figure 2 shows the phase shift and propagation times between two
CAN nodes.
4/20
AN2352
Configuration of the CAN bit timing
Figure 2.
Propagation time segment
Sync_Seg
Prop_Seg
Phase_Seg1
Phase_Seg2
Node B
Delay A_to_B
Delay B_to_A
Node A
Delay A_to_B >= node output delay(A) + bus line delay(AÆB) + node input delay(B)
Prop_Seg
>= Delay A_to_B + Delay B_to_A
Prop_Seg
>= 2 • [max(node output delay + bus line delay + node input delay)]
In this example, both nodes A and B are transmitters performing an arbitration for the CAN
bus. Node A has sent its start of frame bit less than one bit time earlier than node B,
therefore node B has synchronized itself to the received edge from recessive to dominant.
Since node B has received this edge delay (A_to_B) after it has been transmitted, B’s bit
timing segments are shifted in relation to A. Node B sends an identifier with a higher priority
and therefore will win the arbitration at a specific identifier bit when it transmits a dominant
bit while node A transmits a recessive bit. The dominant bit transmitted by node B arrives at
node A after the delay (B_to_A).
Due to oscillator tolerances, the actual position of node A’s sample point can be anywhere
inside the nominal range of node A’s phase buffer segments, so the bit transmitted by node
B must arrive at node A before the start of Phase_Seg1. This condition defines the length of
Prop_Seg.
If the edge from recessive to dominant transmitted by node B would arrive at node A after
the start of Phase_Seg1, it is possible that node A samples a recessive bit instead of a
dominant bit, resulting in a bit error and the destruction of the current frame by an error flag.
The error occurs only when two nodes with oscillators at opposite ends of the tolerance
range and separated by a long bus line arbitrate for the CAN bus; this is an example of a
minor error in the bit timing configuration (Prop_Seg too short) that causes sporadic bus
errors.
1.3
Phase buffer segments and synchronization
The phase buffer segments (Phase_Seg1 and Phase_Seg2) and the synchronization jump
width (SJW) are used to compensate the oscillator tolerance. The phase buffer segments
may be lengthened or shortened by synchronization.
Synchronizations occur on edges from recessive to dominant; their purpose is to control the
distance between edges and sample points.
Edges are detected by sampling the actual bus level in each time quantum and comparing it
with the bus level at the previous sample point. A synchronization is possible only if a
5/20
Configuration of the CAN bit timing
AN2352
recessive bit was sampled at the previous sample point and if the actual time quantum’s bus
level is dominant.
An edge is synchronous if it occurs inside of Sync_Seg, otherwise the distance between an
edge and the end of Sync_Seg is the edge phase error, measured in time quanta. If the
edge occurs before Sync_Seg, the phase error is negative, otherwise, it is positive.
Two types of synchronization exist: hard synchronization and resynchronization. A hard
synchronization occurs once at the start of a frame. Resynchronizations occur only inside a
frame.
●
Hard synchronization
After a hard synchronization, the bit time is restarted at the end of Sync_Seg,
regardless of the edge phase error. Thus hard synchronization forces the edge which
placed the hard synchronization into the synchronization segment of the restarted bit
time.
●
Bit resynchronization
Resynchronization leads to a shortening or lengthening of the bit time such that the
position of the sample point is shifted in relation to the edge.
When a positive phase error of the edge causes resynchronization, Phase_Seg1 is
lengthened. If the magnitude of the phase error is less than the SJW, Phase_Seg1 is
lengthened by the magnitude of the phase error, otherwise it is lengthened by the SJW.
When a negative phase error of the edge causes resynchronization, Phase_Seg2 is
shortened. If the magnitude of the phase error is less than SJW, Phase_Seg2 is
shortened by the magnitude of the phase error, otherwise it is shortened by the SJW.
When the magnitude of the phase error of the edge is less than or equal to the programmed
value of the SJW, the results of hard synchronization and resynchronization are the same. If
the magnitude of the phase error is greater than the SJW, the resynchronization cannot
entirely compensate the phase error and an error of (phase error - SJW) remains.
Only one synchronization occurs between two sample points. The synchronizations
maintain a minimum distance between edges and sample points, giving the bus level time to
stabilize and filtering out spikes that are shorter than (Prop_Seg + Phase_Seg1).
Apart from noise spikes, most synchronizations are caused by arbitration. All nodes
synchronize “hard” on the edge transmitted by the “leading” transceiver that started
transmitting first, but due to propagation delay times, they are not ideally synchronized. The
“leading” transmitter does not necessarily win the arbitration, therefore the receivers must
synchronize themselves to different transmitters that subsequently “take the lead” and that
are synchronized differently to the previously “leading” transmitter. The same happens at the
acknowledge field, where the transmitter and some of the receivers must synchronize to the
receiver that “takes the lead” in the transmission of the dominant acknowledge bit.
Synchronizations after the end of the arbitration are caused by oscillator tolerance, when the
differences in the oscillator’s clock periods of transmitter and receivers sum up during the
time between synchronizations (maximum 10 bits). These summarized differences may not
be longer than the SJW, limiting the oscillator’s tolerance range.
The examples in Figure 3 show how the phase buffer segments compensate phase errors.
There are three drawings of each two consecutive bit timings. The upper drawing shows the
synchronization on a “late” edge, the lower drawing shows the synchronization on an “early”
edge and the middle drawing is the reference without synchronization.
6/20
AN2352
Configuration of the CAN bit timing
Figure 3.
Rx-input
Synchronization on “late” and “early” edges
recessive
dominant
“late” edge
Sample-point
Sample-point
Sample-point
Sample-point
Sample-Point
Sample-Point
recessive
dominant
“early” edge
Rx-input
Sync_Seg
Prop_Seg
Phase_Seg1
Phase_Seg2
In the first example, an edge from recessive to dominant occurs at the end of Prop_Seg.
The edge is “late” since it occurs after the Sync_Seg. Reacting to the “late” edge,
Phase_Seg1 is lengthened so that the distance from the edge to the sample point is the
same as it would have been from the Sync_Seg to the sample point if no edge had
occurred. The phase error of this “late” edge is less than the SJW, so it is fully compensated
and the edge from dominant to recessive at the end of the bit, which is one nominal bit time
long, occurs in the Sync_Seg.
In the second example, an edge from recessive to dominant occurs during Phase_Seg2.
The edge is “early” since it occurs before a Sync_Seg. Reacting to the “early” edge,
Phase_Seg2 is shortened and Sync_Seg is omitted, so that the distance from the edge to
the sample point is the same as it would have been from an Sync_Seg to the sample point if
no edge had occurred. As in the previous example, the magnitude of this “early” edge’s
phase error is less than the SJW, so it is fully compensated.
The phase buffer segments are lengthened or shortened only temporarily; at the next bit
time, the segments return to their nominal programmed values.
In these examples, the bit timing is seen from the point of view of the CAN implementation’s
state machine, where the bit time starts and ends at the sample points. The state machine
omits Sync_Seg when synchronizing on an “early” edge because it cannot subsequently
redefine that time quantum of Phase_Seg2 where the edge occurs to be the Sync_Seg.
7/20
Configuration of the CAN bit timing
1.4
AN2352
System clock tolerance range
The CAN system clock for the different nodes in the network is typically derived from a
different clock generator source. The actual CAN system clock frequency for each node
(and consequently the actual bit time) is affected by a tolerance. In particular, for the
ST10F27x, the system clock is derived (prescaled) from the CPU clock, typically generated
by the main oscillator’s on-chip PLL multiplying frequency.
For effective communication, all CAN nodes in the network must sample the correct value
for each transmitted bit. Also, those nodes (typically at opposite ends of the network) with
the largest propagation delay and working with system clocks that are at opposite limits of
the frequency tolerance, must correctly receive and decode every message transmitted on
the network.
Considering the effect of the system clock discrepancy between two CAN nodes and
supposing no bus errors are detected (due to, for instance, electrical disturbances), bit
stuffing guarantees that even in the worst case condition for the accumulation of phase
errors (during normal communication), the maximum time between two resynchronization
edges is 10 bit periods (5 dominant bits followed by 5 recessive bits are always followed by a
dominant bit).
Calling tBT the CAN Bit Time, this maximum time tJ between two resynchronization edges
can be simply expressed as:
t J = 10 ⋅ t BT
Then, assuming the two CAN nodes have opposite system clock generator tolerance
(considering the specified tolerance "df" valid for both nodes in the network) for their
respective system clocks, the accumulated phase error at the resynchronization instant
becomes:
∆t J = ( 2 ⋅ df ) ⋅ 10 ⋅ t BT
where “df” represents the system clock relative tolerance (f actual frequency, fN nominal
frequency):
f – fN
df = ---------------fN
This error must be compensated, therefore it must be less than the programmed
(Re)Synchronization Jump Width (SJW). Calling tSJW the duration of the resynchronization
segment (programmable from 1 to 4 time quanta), the following condition can be written:
( 2 ⋅ df ) ⋅ 10 ⋅ t BT < t SJW
This expression can be seen as a condition for the CAN system clock tolerance df:
( t SJW )
df < --------------------------------2 ⋅ 10 ⋅ t BT
Considering now that real systems typically operate in the presence of electrical
disturbances, errors on the CAN bus may occur. When an error is detected, an error flag is
transmitted on the bus: If the error is just local, only the node which detected it transmits the
error flag on the bus, while the other nodes simply receive the error flag and then transmit
their own error flags as an echo. On the contrary, if the error is global, all nodes detect it
within the same bit time and transmit their own error flags simultaneously. In this way, each
8/20
AN2352
Configuration of the CAN bit timing
node recognizes if the error is local or global by simply detecting that there is an echo after
its error flag. This is possible only if the node can properly sample the first bit after
transmitting the error flag.
The error flag from an error active node is composed of 6 dominant bits; in the worst case
condition of a bit stuffing error, up to 6 other dominant bits could be received before the error
flag. This means that the first bit after the error flag is the 13th bit after the last
synchronization: This bit, as already stated, must be correctly sampled.
Again, tBT being the CAN bit time, the maximum time tS (with correct sampling) between two
resynchronization edges can be expressed as:
t S = 13 ⋅ t BT – t PB2
where tPB2 corresponds to the duration of Phase_Seg2 (PB = phase buffer).
Also in this case, assuming the two CAN nodes have opposite system clock generator
tolerance (considering the specified tolerance "df" valid for both nodes in the network) for
their respective system clocks, the accumulated phase error at the resynchronization instant
becomes:
∆t S = ( 2 ⋅ df ) ⋅ ( 13 ⋅ t BT – t PB2 )
For a correct sampling, the accumulated phase error must not lead the resynchronization
edge outside the interval Phase_Seg1 + Phase_Seg2. This condition can be expressed as:
t PB 1 < ( 2 ⋅ df ) ⋅ ( 13 ⋅ t BT – t Seg 2 ) < t PB2
Once again, this expression can be translated into a condition for the CAN system clock
tolerance df:
min ( t PB 1, t PB2 )
df < --------------------------------------------------------------( 2 ⋅ ( 13 ⋅ t BT – t PB2 ) )
In conclusion, both conditions on the CAN system clock tolerance must be satisfied.
In case the CAN node generates its system clock through a PLL, the maximum allowed
clock tolerance must also be a function of the PLL jitter: This results in a more severe quality
requirement for the oscillator (crystal or resonator).
The phase error introduced by the PLL jitter is linked to the number of clock periods: In
particular, the jitter increases with the clock period number until a saturation maximum value
is attained, which results in the long term jitter (refer to datasheet for more details about the
PLL electrical characteristics).
Considering the PLL effect, the two expressions producing the phase error in the two
conditions above are modified as follows:
∆t J = 2 ⋅ ( df ⋅ 10 ⋅ t BT – δPLL )
∆t S = 2 ⋅ [ df ⋅ ( 13 ⋅ t BT – t PB2 ) + δPLL ]
where δPLL represents the absolute deviation introduced by the PLL jitter. In the two
formulas, the value of δPLL is evaluated for different numbers of clock periods: For the first,
the jitter corresponding to a 10-bit time period must be considered, while for the second, the
jitter corresponding to a 13-bit time period must be considered. The number of clock periods
9/20
Configuration of the CAN bit timing
AN2352
is computed taking into account the baud rate prescaler setting as well. Again, the factor 2,
which multiplies the single CAN node phase deviation, takes into account the worst case
eventuality that the two communicating nodes are at the opposite limits of the specified
frequency tolerance.
From the two equations above, the new constraints for the CAN system clock tolerance can
be translated into new quality requirements for the oscillator:
( t SJW ) – ( 2 ⋅ δPLL )
df < -------------------------------------------------------2 ⋅ 10 ⋅ t BT
min ( t PB 1, t PB2 ) – ( 2 ⋅ δPLL )
df < ----------------------------------------------------------------------------------( 2 ⋅ ( 13 ⋅ t BT – t PB2 ) )
It is evident that PLL jitter imposes more stringent constraints on oscillator tolerance than
what is acceptable when no PLL is used. ST10F27x PLL characteristics are such that the
oscillator requirements are acceptably impacted by jitter for the majority of the worst case
CAN bus network configurations, as discussed in detail in Section 3: ST10F27x PLL jitter
effect in CAN protocol.
It must be considered that the SJW may not be larger than the smaller of the phase buffer
segments and that the propagation time segment limits the part of the bit time that may be
used for the phase buffer segments.
The combination Prop_Seg = 1 and Phase_Seg1 = Phase_Seg2 = SJW = 4 allows the
largest possible frequency tolerance of 1.58% (in the absence of PLL jitter). This
combination with a propagation time segment of only 10% of the bit time is not suitable for
short bit times; it can be used for bit rates of up to 125 Kbit/s (bit time = 8µs) with a bus
length of 40m.
1.5
Configuration of the CAN protocol controller
In most CAN implementations and also in the C-CAN, the bit timing configuration is
programmed in 2 register bytes. The sum of Prop_Seg and Phase_Seg1 (as TSEG1) is
combined with Phase_Seg2 (as TSEG2) in 1 byte; SJW and BRP are combined in the other
byte.
In these bit timing registers, the four components TSEG1, TSEG2, SJW and BRP must be
programmed to a numerical value that is one less than its functional value; values in the
range of [0...n-1] are programmed instead of values in the range of [1...n]. That way, for
example, SJW (functional range of [1...4]) is represented by only 2 bits.
Therefore, the length of the bit time is (programmed values) [TSEG1 + TSEG2 + 3] tq or
(functional values) [Sync_Seg + Prop_Seg + Phase_Seg1 + Phase_Seg2] tq.
10/20
AN2352
Configuration of the CAN bit timing
Figure 4.
Structure of the CAN Core’s CAN Protocol Controller
Configuration (BRP)
Scaled_clock (tq)
bit stream processor
System clock Baud rate
prescaler
Sample_point
Sampled_bit
Transmit_data
Bit
timing
logic
Sync_mode
Bit_to_send
IPT
Receive_data
Bus_off
Control
Status
Received_data_bit
Send_message
Control
Next_data_bit
Shift register
Received_message
Configuration (TSEG1, TSEG2, SJW)
The data in the bit timing registers is the configuration input of the CAN protocol controller.
The Baud rate prescaler (whose value is configured by the BRP field of the bit timing
register) defines the length of the time quantum, the basic time unit of the bit time; the bit
timing logic (configured by TSEG1, TSEG2 and SJW) defines the number of time quanta in
the bit time.
The processing of the bit time, the calculation of the position of the sample point and
occasional synchronizations are controlled by the BTL state machine, which is evaluated
once each time quantum. The rest of the CAN protocol controller, the bit stream processor
(BSP) state machine, is evaluated once each bit time at the sample point.
The Shift Register serializes the messages to be sent and parallelizes received messages.
Its loading and shifting is controlled by the BSP.
The BSP translates messages into frames and frames into messages. It generates and
discards the enclosed fixed format bits, inserts and extracts stuff bits, calculates and checks
the CRC code, performs the error management and determines the type of synchronization
to be used. It is evaluated at the sample point and processes the sampled bus input bit. The
time needed to calculate the next bit to be sent after the sample point (for example, data bit,
CRC bit, stuff bit, error flag or idle) is called the information processing time (IPT).
The IPT is application specific but may not be longer than 2 tq; the C-CAN’s IPT is 0 tq. Its
length is the lower limit of the programmed length of Phase_Seg2. In case of a
synchronization, Phase_Seg2 may be shortened to a value less than IPT, which does not
affect bus timing.
11/20
Configuration of the CAN bit timing
1.6
AN2352
Calculation of the bit timing parameters
Usually, the calculation of the bit timing configuration starts with a desired bit rate or bit time.
The resulting bit time (1/bit rate) must be an integer multiple of the system clock period.
The bit time consists of 4 to 25 time quanta. The length of the time quantum tq is defined by
the Baud rate prescaler with tq = (Baud rate prescaler)/fsys. Several combinations may lead
to the desired bit time, allowing iterations of the following steps.
The first part of the bit time to be defined is the Prop_Seg. Its length depends on the delay
times measured in the system. A maximum bus length as well as a maximum node delay
must be defined for expandable CAN bus systems. The resulting time for Prop_Seg is
converted into time quanta (rounded up to the nearest integer multiple of tq).
The Sync_Seg is 1 tq long (fixed), leaving (bit time – Prop_Seg – 1) tq for the two phase
buffer segments. If the number of remaining tq is even, the phase buffer segments have the
same length, Phase_Seg2 = Phase_Seg1, otherwise Phase_Seg2 = Phase_Seg1 + 1.
The minimum nominal length of Phase_Seg2 must also be considered. Phase_Seg2 may
not be shorter than the CAN controller’s information processing time, which, depending on
the actual implementation, is in the range of [0...2] tq.
The length of the synchronization jump width is set to its maximum value, which is the
minimum of 4 and Phase_Seg1.
The oscillator tolerance range necessary for the resulting configuration is calculated by the
formulas expressed in Section 1.4: System clock tolerance range.
If more than one configuration is possible, that configuration allowing the highest oscillator
tolerance range should be chosen.
CAN nodes with different system clocks require different configurations to attain the same
bit rate. The calculation of the propagation time in the CAN network, based on the nodes
with the longest delay times, is done once for the whole network.
The CAN system’s oscillator tolerance range is limited by that node with the lowest tolerance
range.
The calculation may show that bus length or bit rate must be decreased or that the oscillator
frequencies’ stability must be increased in order to find a protocol compliant configuration of
the CAN bit timing.
The resulting configuration is written into the bit timing register:
(Phase_Seg2 - 1) and (Phase_Seg1 + Prop_Seg - 1) and (SynchronizationJumpWidth - 1)
and (Prescaler - 1)
12/20
AN2352
1.6.1
Configuration of the CAN bit timing
Example for bit timing at high baud rate
In this example, CPU clock frequency is 40 MHz, the frequency of the CAN module clock is
20 MHz, BRP is 1 and the bit rate is 1 Mbit/s. By default, the ST10F27x divides by 2 the
clock that feeds the CAN cells (mandatory when the CPU clock frequency is higher than
40 MHz). It is possible to disable this function by setting bit 2 of the XMISC register.
tq
100 ns
delay of bus driver
50 ns
delay of receiver circuit
30 ns
delay of bus line (40m)
220 ns
tProp
600 ns
= 6 x tq
tPB1
100 ns
= 1 x tq
tTSeg1
700 ns
= tProp + tPB1
tTSeg2
200 ns
= Information processing time + 1 • tq
tSJW
100 ns
= 1 x tq
tSync-Seg
100 ns
= 1 x tq
bit time
1000 ns
= tSync-Seg + tTSeg1 + tTSeg2
tolerance for CAN clock
= 2 x tCAN_CLK
=
( t SJW )
min (PB1 , PB2)
min ⎛ -----------------------------------------------------------------------, ----------------------------------⎞
⎝ 2 ⋅ ( 13 ⋅ bit_time – PB2 ) 2 ⋅ 10 ⋅ t BT⎠
min (PB1 , PB2)
0.1µs
----------------------------------------------------------------------- = ------------------------------------------------------------ = 0, 39%
2 ⋅ ( 13 ⋅ bit_time – PB2 )
2 ⋅ ( 13 ⋅ 1µs – 0.2µs )
( t SJW )
0.1µs
--------------------------------- = -------------------------------------- = 0, 5%
2 ⋅ 10 ⋅ t BT
2 ⋅ ( 10 ⋅ 1µs )
tolerance for CAN clock
= 39%
In this example, the concatenated bit time parameters are (2-1)3 and (7-1)4 and (1-1)2 and
(1)6 and the Bit Timing Register is programmed to = 0x1601.
13/20
Configuration of the CAN bit timing
1.6.2
AN2352
Example for bit timing at low baud rate
In this example, CPU clock frequency is 64 MHz, the frequency of CAN module clock is
32 MHz, BRP is 31 and the bit rate is 100 Kbit/s. By default, the ST10F27x divides by 2 the
clock that feeds the CAN cells (mandatory when the CPU clock frequency is higher than
40 MHz). It is possible to disable this function by setting bit 2 of the XMISC register.
tq
1 µs
delay of bus driver
200 ns
delay of receiver circuit
80 ns
delay of bus line (40m)
220 ns
tProp
1 µs
= 1 x tq
tPB1
4 µs
= 4 x tq
tTSeg1
5 µs
= tProp + tPB1
tTSeg2
4 µs
= Information Processing Time + 3 • tq
tSJW
4 µs
= 4 x tq
tSync-Seg
1 µs
= 1 x tq
bit time
10 µs
= tSync-Seg + tTSeg1 + tTSeg2
tolerance for CAN clock
= 32 x tCAN_CLK
=
( t SJW ) ⎞
min (PB1 , PB2)
min ⎛ -----------------------------------------------------------------------, --------------------------------⎝ 2 ⋅ ( 13 ⋅ bit_time – PB2 ) 2 ⋅ 10 ⋅ t BT⎠
min (PB1 , PB2)
4µs
----------------------------------------------------------------------- = ----------------------------------------------------------- = 1.58%
2 ⋅ ( 13 ⋅ bit_time – PB2 )
2 ⋅ ( 13 ⋅ 10µs – 4µs )
( t SJW )
4µs
--------------------------------- = -----------------------------------------= 2%
2 ⋅ 10 ⋅ t BT
2 ⋅ ( 10 ⋅ 10µs )
tolerance for CAN clock
= 1.58%
In this example, the concatenated bit time parameters are (4-1)3 and (5-1)4 and (4-1)2 and
(31)6 and the bit timing register is programmed to = 0x34DF.
14/20
AN2352
2
Phase locked loop (PLL)
Phase locked loop (PLL)
The internal operation of the ST10F27x is controlled by the internal CPU clock fCPU. The
CPU clock signal can be generated by different mechanisms. The mechanism used to
generate the CPU clock is selected during reset by the logic levels on pins P0.15-13
(P0H.7-5).
When pins P0.15-13 (P0H.7-5) equal ‘001’ during reset, the CPU clock is derived from the
internal oscillator (input clock signal) by a 2:1 prescaler.
When pins P0.15-13 (P0H.7-5) equal ‘011’ during reset, the on-chip phase locked loop is
disabled, the on-chip oscillator amplifier is bypassed and the CPU clock is directly driven by
the input clock signal on a specific pin (XTAL1).
For all other combinations of pins P0.15-13 (P0H.7-5) during reset, the on-chip phase
locked loop is enabled and it provides the CPU clock. The PLL multiplies the input frequency
by the factor F which is selected via the combination of pins P0.15-13 (fCPU = fXTAL x F).
With every F’th transition of fcpu the PLL circuit synchronizes the CPU clock to the input
clock. This synchronization occurs smoothly, to avoid an abrupt change in the CPU clock
frequency.
2.1
PLL jitter
Two kinds of PLL jitter are defined:
●
Self referred single period jitter
Also called "Period Jitter", it can be defined as the difference of the Tmax and Tmin,
where Tmax is the maximum time period of the PLL output clock and Tmin is the
minimum time period of the PLL output clock.
●
Self referred long term jitter
Also called "N period jitter", it can be defined as the difference of Tmax and Tmin, where
Tmax is the maximum time difference between N + 1 clock rising edges and Tmin is the
minimum time difference between N + 1 clock rising edges. Here N should be kept
sufficiently large to have the long term jitter. For N = 1, this becomes the single period
jitter.
Jitter at the PLL output is caused by:
2.1.1
●
Jitter in the input clock
●
Noise in the PLL loop
Jitter in the input clock
PLL acts like a low pass filter for any jitter in the input clock. Input Clock jitter with the
frequencies within the PLL loop bandwidth is passed to the PLL output and higher frequency
jitter (frequency > PLL bandwidth) is attenuated at 20dB/decade.
2.1.2
Noise in the PLL loop
This condition again is attributed to the following sources:
●
Device noise of the circuit in the PLL
●
Noise in supply and substrate
15/20
Phase locked loop (PLL)
AN2352
Device noise of the circuit in the PLL
Long term jitter is inversely proportional to the bandwidth of the PLL: The wider the loop
bandwidth, the lower the jitter due to noise in the loop. Moreover, long term jitter is
practically independent of the multiplication factor.
The most noise sensitive circuit in the PLL circuit is definitely the VCO (voltage controlled
oscillator). There are two main sources of noise: thermal (random noise, frequency
independent thus practically white noise) and flicker (low frequency noise). These two noise
sources lead to a jitter as illustrated in Figure 5. This figure shows three distinctive zones:
–
the first zone in which the R.M.S. value of the accumulated jitter is proportional to
the square root of N, where N is the number of clock periods within the considered
time interval,
–
the second zone in which the R.M.S. value of the accumulated jitter is proportional
to N and,
the third zone where for a large value of N, a saturation effect is evident, so the
jitter does not grow anymore when considering a longer time interval (jitter stable
increasing the number of clock periods N). The saturation value corresponds to
what has been called self referred long term jitter of the PLL. In Figure 5 the
maximum jitter trend versus the number of clock periods N (for some typical CPU
frequencies) is reported: The curves represent the very worst case, computed
taking into account all corners of temperature, power supply and process
variations; the real jitter is always measured well below the given worst case
values.
–
Noise in supply and substrate
Digital supply noise adds determining elements to PLL output jitter, independent of the
multiplication factor. Its effect is strongly reduced thanks to particular care used in the
physical implementation and integration of the PLL module inside the device. In any case,
the contribution of digital noise to global jitter is widely taken into account in the curves
provided in Figure 5.
Figure 5.
ST10F27x PLL jitter
±5
16 MHz 24 MHz 32 MHz
40 MHz
64 MHz
±4
±3
±2
±1
TJIT
0
16/20
0
200
400
600
800
1000
N (CPU clock periods)
1200
1400
AN2352
3
ST10F27x PLL jitter effect in CAN protocol
ST10F27x PLL jitter effect in CAN protocol
The CAN protocol provides a mechanism to resynchronize from recessive to dominant after
every edge, as explained in Section 1.3: Phase buffer segments and synchronization. The
two phase buffers and the synchronization jump make it possible to compensate the
oscillator or PLL tolerance.
Considering only the PLL effects, the C-CAN module present in the ST10F27x can always
compensate its PLL jitter. In the worst case, in fact, the long term jitter is +/- 4.5ns (Figure 5
on page 16). From the jitter point of view, one of the worst CAN bit time configurations is
when tBT = 25tq, SJW = 1, tSJW = 1tq = 40ns. Considering that the summarized difference
between the receiver and the transmitter is 9ns, Synchronization Jump Width is sufficient to
compensate that difference. In other words, the numerator of the second term of the formula
(Section 1.4: System clock tolerance range):
( t SJW ) – ( 2 ⋅ δPLL )
df < -------------------------------------------------------2 ⋅ 10 ⋅ t BT
is always positive, leading in any case to a system clock tolerance range. In the same way if
tBT = 1µ, tBT = 18tq, tPB2 = 1tq, the numerator of the second term of the formula:
min ( t PB 1, t PB2 ) – ( 2 ⋅ δPLL )
df < ----------------------------------------------------------------------------------( 2 ⋅ ( 13 ⋅ t BT – t PB2 ) )
is always positive, leading again to a system clock tolerance range.
3.1
System clock tolerance range reduction in presence of PLL
jitter
Even if the C-CAN module always compensates its PLL jitter, the system clock tolerance
range is nevertheless reduced, increasing the probability of errors. This section evaluates
that reduction and also provides two examples of configuration already dealt with in
Section 1.6: Calculation of the bit timing parameters.
3.1.1
Range reduction percentage
df – df PLL
2 ⋅ δPLL
---------------------------- = -----------------------df
t SJW
df – df PLL
2 ⋅ δPLL
---------------------------- = ----------------------------------------------df
min ( t PB 1, t PB2 )
The above equations have been calculated starting from the relations of the system clock
tolerance range. Those quantities cannot be higher than 22.5% (worst case: δPLL = 4.5ns,
tSJW = min(tPB1,tPB2) = 40ns).
17/20
ST10F27x PLL jitter effect in CAN protocol
3.1.2
AN2352
Examples
In the first example of Section 1.6, the frequency of the CAN module clock was 20 MHz,
BRP = 1 and the bit rate 1 Mbit/s. Using the Figure 5 on page 16, it follows that
δPLL ( 13 ⋅ 10 ⋅ tq = 520 ⋅ t CPU ) = 3ns
so the clock tolerance range is reduced by
( 2 ⋅ δPLL )
0.006µs
--------------------------------------------------------------- = ------------------------------------------------------------ = 0.02%
( 2 ⋅ ( 13 ⋅ t BT – t PB2 ) )
2 ⋅ ( 13 ⋅ 1µs – 0.2µs )
becoming 0.37%.
Using the range reduction formula calculated in the previous section:
df – df PLL
6 - = 0.06 = 6%
---------------------------- = --------100
df
In the second example, the frequency of CAN module clock was 32 MHz, BRP = 31 and the
bit rate 100 Kbit/s. Using the Figure 5 on page 16, it follows that
δPLL ( 13 ⋅ 10 ⋅ tq = 4160 ⋅ t CPU ) = 4.5ns
so the clock tolerance range is reduced by
( 2 ⋅ δPLL )
0.009µs
--------------------------------------------------------------- = ----------------------------------------------------------- = 0.0035%
( 2 ⋅ ( 13 ⋅ t BT – t PB2 ) )
2 ⋅ ( 13 ⋅ 10µs – 4µs )
which is negligible compared to the original value of 1.58%.
In fact, using the range reduction formula calculated in the previous section:
df – df PLL
9
---------------------------- = ------------- = 0.00225 = 0.225%
df
4000
3.2
Conclusion
Given the characteristics of the ST10F27x PLL, in most configurations the PLL can be used
and it fulfills the CAN standard requirements.
18/20
AN2352
4
Revision history
Revision history
Table 2.
Document revision history
Date
Revision
Changes
25-Apr-2006
1
Initial release
24-Sep-2013
2
Updated Disclaimer.
19/20
AN2352
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
DocID12300 Rev 2
20/20
20