Series AMEPR40N-Z up to 1000mA | AC-DC LED driver FEATURES: Constant Current LED Driver Low Output Current Ripple Active Power Factor Correction Short Circuit, Over Voltage, Over Temperature Protection Models Single output Model Max Output Power (W) Output Voltage Range (V) 33.6 35.7 37.8 42.0 24-42 24-42 24-42 24-42 AMEPR40N-4280Z AMEPR40N-4285Z AMEPR40N-4290Z AMEPR40N-42100Z Output Current (mA) 800 850 900 1000 No Flicker IP62 rated Low THD 5 Year Warranty Input Voltage (VAC/Hz) Efficiency 230VAC (%) 90-305/47-63 90-305/47-63 90-305/47-63 90-305/47-63 82 83 84 84 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity <75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Input Current Inrush current <2ms Leakage current Input dissipation Power Factor Conditions Typical Maximum Units 90 VAC, full load 230 VAC, cold start 0.63 60 0.75 1.9 2.9 3.1 0.99 0.95 250V/2A 1.5 1.0 15 20 25 Arms A mA Maximum Units 115Vac, no load 230Vac, no load 277Vac, no load 115 VAC, full load 277 VAC, full load Input Fuse Start-up Time THD 115 VAC, full load 277 VAC, full load 115Vac, full load, 36Vout 230Vac, full load, 36Vout 277Vac, full load, 36Vout W Sec. Sec. % Output Specifications Parameters Conditions Typical Current accuracy ±5 Line regulation LL to HL ±1 Load regulation Full Output Voltage Range ±1 Ripple & Noise* 150 Output Current Ripple* Full load Current Overshoot LL to HL, full load at cold start Hold-up time (min.) Minimum Load Voltage See Models Table Above * Tested with 0.1µF (C/C) or (M/C) and 10µF (E/C) parallel capacitors at the end. 420 50 10 1.0 % % % mV p-p mA % ms Isolation Specifications Parameters Tested I/O voltage Isolation Resistance Isolation Capacitance www.aimtec.com F 052.1e R3 Conditions Typical I/P – O/P I/P – FG O/P – FG I/P – O/P, 500Vdc >100MΩ 150 Tel: +1 514 620 2722 1 of 7 Rated Units 3750 2000 500 VAC VAC VAC VAC pF Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR40N-Z up to 1000mA | AC-DC LED driver General Specifications Parameters Conditions Switching frequency Over voltage protection Short circuit protection Input power while Short circuit Over Temperature Protection Operating temperature Maximum case temperature Warranty case temperature Storage temperature Temperature coefficient Cooling Humidity Atmospheric pressure Case material IP Rating Weight Dimensions (L X W+ X H) MTBF Typical Maximum Units 49 KHz VDC 100 Limiting Voltage Continuous, Hiccup Mode 230VAC Threshold – Shutdown Output Hysteresis – Auto Recovery Without derating 3 W oC +103 +85 oC oC -30 to +50 oC 95 60 oC oC -40 to +85 0.05 % / oC 20 - 90 86-106 % RH Kpa Free Air Convection Plastic IP62 180 6.61 x 1.85 x 0.98 inches 168.0 x 47.0 x 25.0 mm 450,000 hrs (MIL-HDBK-217F at +25°C) g Safety Specifications Parameters Standards Electromagnetic Interference EN55015 / FCC Part 15, Class B Harmonic Current Emissions EN61000-3-2, Class B Voltage fluctuations and flicker EN61000-3-3 Electrostatic Discharge Immunity EN61000-4-2, 8kV Air, 4kV Contact, Level 3, Criteria A RF, Electromagnetic Field Immunity EN61000-4-3, Test-RS Level 3, Criteria A Electrical Fast Transient / Burst Immunity EN61000-4-4, Burst EFT Level 3, Criteria A Surge Immunity EN61000-4-5, Line to Neutral 2kV, Line/Neutral to PE 4kV RF, Conducted Disturbance Immunity EN61000-4-6. Test-CS Level 3, Criteria A Power frequency Magnetic Field Immunity EN61000-4-8, Test 3A/m, Criteria A Voltage dips, Short Interruptions Immunity EN61000-4-11, Criteria B Electromagnetic Immunity Requirements Applies EN61547 to Lighting Equipment Designed in compliance with UL 8750, Type TL, class P, EN 61347-1, EN 61347-2-13, EN 60950-1 Pin Definition Application Block diagram Recommended Wire gauge Connection 20-24 20-24 14-26 14-26 AC L AC N LED+ LED- www.aimtec.com F 052.1e R3 AC1 LED+ 1st LED AC LED AC2 Tel: +1 514 620 2722 2 of 7 LED LED- Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR40N-Z up to 1000mA | AC-DC LED driver Dimensions 47.0 1.85 25.0 0.98 168.0 6.61 Side View1 25.0 0.98 168.0 6.61 Side View2 47.0 1.85 SCREW HOLE 25.0 0.98 LINE SLOT Efficiency Vs. Input Voltage & Output Current (Constant current load) AMEPR40N-4280Z 95.00% 90.00% Efficiency 85.00% 115 VAC 80.00% 230 VAC 75.00% 277 VAC 70.00% 65.00% 24 27 30 33 36 39 42 Output Voltage(V) www.aimtec.com F 052.1e R3 Tel: +1 514 620 2722 3 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR40N-Z up to 1000mA | AC-DC LED driver AMEPR40N-4285Z 95.00% 90.00% Efficiency 85.00% 115 VAC 80.00% 230 VAC 75.00% 277 VAC 70.00% 65.00% 24 27 30 33 36 39 42 Output Voltage (V) AMEPR40N-4290Z 95.00% 90.00% Efficiency 85.00% 115 VAC 80.00% 230 VAC 75.00% 277 VAC 70.00% 65.00% 24 27 30 33 36 39 42 Output Voltage(V) www.aimtec.com F 052.1e R3 Tel: +1 514 620 2722 4 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR40N-Z up to 1000mA | AC-DC LED driver AMEPR40N-42100Z 95.00% 90.00% Efficiency 85.00% 115 VAC 80.00% 230 VAC 75.00% 277 VAC 70.00% 65.00% 24 27 30 33 36 39 42 Output Voltage(V) PFC Value vs. Output Load Current (constant current mode) AMEPR40N-4280Z 1.2 PF 0.9 115 VAC 0.6 230 VAC 277 VAC 0.3 0 24 27 30 33 36 39 42 Output Voltage (V) www.aimtec.com F 052.1e R3 Tel: +1 514 620 2722 5 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR40N-Z up to 1000mA | AC-DC LED driver AMEPR40N-4285Z 1.200 PF 0.900 115 VAC 0.600 230 VAC 277 VAC 0.300 0.000 24 27 30 33 36 39 42 Output Voltage (V) AMEPR40N-4290Z 1.200 PF 0.900 115 VAC 0.600 230 VAC 277 VAC 0.300 0.000 24 27 30 33 36 39 42 Output Voltage (V) www.aimtec.com F 052.1e R3 Tel: +1 514 620 2722 6 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR40N-Z up to 1000mA | AC-DC LED driver AMEPR40N-42100Z 1.200 PF 0.900 115 VAC 0.600 230 VAC 277 VAC 0.300 0.000 24 27 30 33 36 39 42 Output Voltage (V) NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5.Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 052.1e R3 Tel: +1 514 620 2722 7 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only