DC MA RES XI IST MU A M NC (O E HM CU S) RR MA E XI NT MU R M ATI (A NG MP S) IN C CU REM RR EN EN TA T L DC (A MP S) NO M IN IN DU AL (µ CT H) A ±1 NC 0% E PA RT High Current Filter Inductors NU MB ER Series 4590 SERIES 4590 Physical Parameters Inches Length 0.900 Max. Diameter 0.455 Max Lead Size AWG #20 TCW 0.032 ± 0.002 Lead Length 1.10 Min. Millimeters 22.86 Max. 11.55 Max 0.813 ± 0.05 27.94 Min. Operating Temperature –55°C to +125°C –55°C to +85°C @ full rated current Current Rating at 85°C Ambient 40°C Rise Maximum Power Dissipation at 85°C 0.70 W Dielectric Withstanding Voltage 2500 V RMS Inductance Measurement Inductance is measured @ 1KHz with 1 VAC open circuit and 0 dc bias. Inductance Tolerance Tolerance is specified by suffixing an alpha character to the part number as follows: J = 5%, K = 10%, and L = 15%. Units are normally supplied to the tolerance indicated in table. Marking Parts are printed with DELEVAN, Inductance Value and Tolerance. 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 18000 22000 27000 33000 39000 47000 56000 68000 82000 100000 0.007 0.008 0.011 0.011 0.013 0.016 0.018 0.020 0.022 0.024 0.025 0.028 0.031 0.034 0.043 0.059 0.066 0.084 0.113 0.129 0.150 0.162 0.226 0.257 0.288 0.393 0.504 0.570 0.643 0.844 0.977 1.18 1.50 1.76 2.13 2.53 2.84 3.79 4.24 5.75 6.44 7.30 9.34 10.7 14.8 18.0 22.7 25.7 29.7 33.7 38.0 52.8 67.3 76.0 Optional Tolerances: J = 5% 9.75 9.11 7.77 7.60 7.15 6.44 6.07 5.76 5.49 5.26 5.15 4.87 4.63 4.45 3.93 3.355 3.175 2.815 2.43 2.27 2.105 2.025 1.715 1.61 1.52 1.30 1.15 1.08 1.015 0.89 0.825 0.75 0.665 0.615 0.56 0.51 0.48 0.415 0.395 0.34 0.32 0.30 0.265 0.25 0.21 0.19 0.17 0.16 0.15 0.14 0.13 0.11 0.10 0.09 8.2 7.5 6.9 6.3 5.7 5.2 4.7 4.3 3.9 3.5 3.2 2.9 2.7 2.5 2.3 2.1 1.9 1.7 1.6 1.4 1.3 1.2 1.1 0.95 0.88 0.80 0.74 0.67 0.61 0.56 0.51 0.46 0.42 0.38 0.34 0.31 0.29 0.26 0.24 0.22 0.20 0.18 0.17 0.15 0.14 0.12 0.11 0.10 0.09 0.09 0.08 0.07 0.07 0.06 POWER INDUCTORS Mechanical Configuration Ferrite Bobbin protected with a flame retardant polyolefin sleeve. 4590-392K 4590-472K 4590-562K 4590-682K 4590-822K 4590-103K 4590-123K 4590-153K 4590-183K 4590-223K 4590-273K 4590-333K 4590-393K 4590-473K 4590-563K 4590-683K 4590-823K 4590-104K 4590-124K 4590-154K 4590-184K 4590-224K 4590-274K 4590-334K 4590-394K 4590-474K 4590-564K 4590-684K 4590-824K 4590-105K 4590-125K 4590-155K 4590-185K 4590-225K 4590-275K 4590-335K 4590-395K 4590-475K 4590-565K 4590-685K 4590-825K 4590-106K 4590-126K 4590-156K 4590-186K 4590-226K 4590-276K 4590-336K 4590-396K 4590-476K 4590-566K 4590-686K 4590-826K 4590-107K L = 15% High Saturation Bobbin allows for high inductance with low DCR. High Resistivity Core offers very high parallel resistance, resulting in maximum coil performance. Incremental Current is the current which will decrease the inductance by approximately 5%. Packaging Bulk only www.delevan.com E-mail: [email protected] 270 Quaker Rd., East Aurora NY 14052 • Phone 716-652-3600 • Fax 716-652-4814 PAGE 2/ 2002 86