D1U86G-W-460-12-HxxDC Series www.murata-ps.com 86mm 1U Front End AC-DC Power Supply Converter PRODUCT OVERVIEW The D1U86G-W-460-12-HxxDC is a bulk front end power supply which meets the needs of systems requiring high efficiency distributed power architectures. The output power of this supply is rated at 460W with one main and one standby output. The supply provides high efficiency performance, hot plug capability, and parallel operation with droop current sharing. Closed-loop internal fan cooling provides reliable long life operation. Industry standard PMBus™ communication protocol makes system integration with this supply seamless and straightforward. The low-profile design and dense packaging makes this supply ideal for delivering reliable, efficient power to servers, workstations, storage devices and other distributed power systems. ORDERING GUIDE Part Number FEATURES 460W output power Power Output Main Output Standby Output Airflow 460W 460W 12V 12V 12V 12V Back to front Front to back D1U86G-W-460-12-HB4DC D1U86G-W-460-12-HB3DC Exceeds 92% efficiency at 50% load (230Vac Input) 12V main output INPUT CHARACTERISTICS Parameter Input Voltage Operating Range Frequency Turn-on Voltage Turn-off Voltage Maximum Input Current (100Vac) Inrush Current Power Factor 12V standby output of 30W 1U height: 3.4" x 7.75" x 1.57" Conditions Ramp up Ramp down 460W At 264Vac at 25°C cold start At 230Vac, full load 20% load Efficiency (230Vac) excluding fan load 50% load 100% load 11.1 Watts per cubic inch density N+1 redundancy capable, including hot plugging (up to 8 in parallel) Droop current sharing on 12V main output, ORing FET Overvoltage, overcurrent, overtemperature protection Internal cooling fan (variable speed) Min. 90 47 81 70.5 Nom. 115/230 50/60 85 74.3 Max. 264 63 89 78 5.5 30 Units Vac Hz Vac Arms Apk 0.99 88 92 88 % OUTPUT VOLTAGE CHARACTERISTICS Output Voltage PMBus™ / I²C interface with status indicators RoHS compliant 1 Parameter Conditions Min. Typ. Max. Units Voltage Set Point 1A load 12.27 12.3 12.33 Vdc Static Regulation 11.85 12.45 Ripple Voltage & Noise1 20MHz Bandwidth 120 mV p-p 12V Droop Regulation 0.27 0.3 0.33 V Output Current 0 38.3 A Load Capacitance 22,000 μF Voltage Set Point 11.97 12.0 12.03 Vdc Line and Load Regulation 11.4 12.6 12VSB Ripple Voltage & Noise1 20MHz Bandwidth 120 mV p-p Output Current 0 2.5 A Load Capacitance 1000 μF Ripple and noise are measured with 0.1 μF of ceramic capacitance and 10 μF of tantalum capacitance on each of the power supply outputs. A short coaxial cable with 50Ω scope termination is used. www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html Available now at www.murata-ps.com/en/3d/acdc.html For full details go to www.murata-ps.com/rohs CB Test Certificate and Test Report PM www.murata-ps.com/support D1U86G-W-460-12-HxxDC.A03 Page 1 of 5 D1U86G-W-460-12-HxxDC Series 86mm 1U Front End AC-DC Power Supply Converter OUTPUT CHARACTERISTICS Parameter Output Rise Monotonicity Startup Time Conditions No voltage excursion AC ramp up 12V, 50% load step, 0.5A/μs di/dt 12VSB, 50% load step, 0.5A/μs di/dt Transient Response Current sharing accuracy (up to 8 in parallel) At 100% load Hot Swap Transients Holdup Time All outputs remain in regulation Min. Typ. Max. Units 1.5 300 600 s mV ±10 % 5 % ms Max. 70 50 90 95 Units 10 ENVIRONMENTAL CHARACTERISTICS Parameter Storage Temperature Range Operating Temperature Range Operating Humidity Storage Humidity Altitude (without derating at 40°C) Shock Operational Vibration MTBF Conditions Min. -40 0 5 5 3000 Noncondensing 30G non operating 1G, 10 – 500 Hz, 1.6G (non-operational) Per Telcordia SR-322 M1C1 @ 40°C Typ. °C % m 635K hrs Safety Approvals (pending) CSA/UL 60950-1-07-2nd Ed. IEC 60950-1:2005 (2nd Edition) w Am. 1:2009 EN 60950-1:2006 +A11:2009 +A1:2010 CE Marking per LVD DIRECTIVE 2006/95/EC Input Fuse Weight Power Supply has internal 6.3A/250V slow blow fuse on the AC line input 1.76 lbs (798g) PROTECTION CHARACTERISTICS Output Voltage 12V 12VSB Parameter Conditions Min. Typ. Max. Units Overtemperature (intake) Overvoltage Overcurrent Overvoltage Overcurrent Autorestart Latching Latching Autorecovery Autorecovery 57 13.6 42 13.6 3.5 60 63 15 49.8 15 5.0 °C V A V A Typ. Max. Units Vrms Vrms ISOLATION CHARACTERISTICS Parameter Conditions Min. Input to Output - Reinforced 3000 Input to Chassis - Basic 1500 Main and standby outputs connected directly to chassis Insulation Safety Rating / Test Voltage Isolation EMISSIONS AND IMMUNITY Characteristic Standard Compliance Input Current Harmonics Voltage Fluctuation and Flicker Conducted Emissions ESD Immunity Radiated Field Immunity Electrical Fast Transient Immunity Surge Immunity Radiated Field Conducted Immunity Magnetic Field Immunity IEC/EN 61000-3-2 IEC/EN 61000-3-3 FCC 47 CFR Part 15/CISPR 22/EN55022 IEC/EN 61000-4-2 IEC/EN 61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 IEC/EN 61000-4-6 IEC/EN 61000-4-8 Complies Complies Class B, 6dB margin Level 3 criteria A Level 3 criteria B Level 3 criteria A Level 3 criteria A Level 3 criteria A 3 A/m criteria B Voltage dips, interruptions IEC/EN 61000-4-11 230Vin, 100% load, Phase 0°, Dip 100% Duration 10ms (A) 230Vin, 50% load, Phase 0°, Dip 100% Duration 20ms (VSB:A, V1:A) 230Vin, 100% load, Phase 0°, Dip 100% Duration > 20ms (VSB, V1:B) www.murata-ps.com/support D1U86G-W-460-12-HxxDC.A03 Page 2 of 5 D1U86G-W-460-12-HxxDC Series 86mm 1U Front End AC-DC Power Supply Converter STATUS INDICATORS AND CONTROL SIGNALS Signal PSON# PRESENT# PS INTERRUPT PS ADDRESS LINES IMON SIGNAL PSOK I2C CLOCK I2C DATA LED State Off Green - solid Description Pulled low to enable main output Present# signal must be pulled high through a resistor to enable the output, either to the PSU 12V bias output as shown in the wiring diagram or to an external system bias output. The external system bias should be between 3.3V (5.1K pullup resistor) and 12V (10K pullup resistor), with pullup resistors sized proportionally for voltages in between. The Present# signal can be used to communicate the number of power supplies in the system (operational or non-operational). The signal is low when power supply is plugged into the system, and is pulled up high when the power supply is unplugged. Present# is a short pin that results in a fast shut down signal to turn off the main output and discharge the output capacitors when the supply is unplugged. Open drain PMBus™ signal A0, A1, A2 Analog representation of main output current AC input not OK and DC output not OK PSOK Low (<0.6V) AC input OK and DC output not OK PSOK Low (<0.6V) AC input OK and DC output OK PSOK High (>0.6V) AC input not OK and DC output OK PSOK Mid-Level (Less than 2.5V, Greater than 2V) I2C clock I2C data Mode Operating Condition AC Turn-off AC Input is below minimum power-supply turn-on specification or the main output is disabled and not delivering power Power-good Power supply standby & main outputs are operating within normal parameters and delivering power OUTPUT CONNECTOR AND SIGNAL SPECIFICATION Power Supply Output Card Edge (Top Side) DC and Signal Connector: Gold Plated Card Edge Fingers Power Blades PB1 PB2 PB3 PB4 PB5 PB6 PB7 PB8 PB9 PB10 Signal PIns S1 S2 S3 S4 S5 S6 S7 S8 S9 S10 S11 S12 S13 S14 S15 S16 Signal Name Vo Vo Vo RTN RTN RTN RTN RTN Vo Vo Signal Name VSB VSB Reserved PS INTERRUPT PRESENT# PSOK IMON PSON# SCL SDA GND A0 A1 A2 RTN RTN PB5 S8 PB4 PB3 PB2 PB1 S1 Power Supply Output Card Edge (Bottom Side) S9 S16 PB6 PB7 PB8 PB9 PB10 www.murata-ps.com/support D1U86G-W-460-12-HxxDC.A03 Page 3 of 5 D1U86G-W-460-12-HxxDC Series 86mm 1U Front End AC-DC Power Supply Converter PERFORMANCE DATA Efficiency Thermal Derating 95 500 450 400 Output Power (W) Efficiency (%) 89 83 77 AC120V AC230V 71 350 300 250 200 90 to 264 Vac Input 150 100 50 65 0 10 20 30 40 50 60 Load (%) 70 80 90 100 0 0 10 20 30 Temperature (C) 40 50 WIRING DIAGRAM FOR OUTPUT Vo - Main Output Vo - Main output PB1, 2, 3, 9, 10 PB1, 2, 3, 9, 10 Main output load R1 RTN RTN PB4-8 S1-2 (12V) VSB (12V) VSB Standby Shutdown S1-2 R1 PRESENT# S5 S5 PRESENT# 10K 10K R2 Main Shutdown PB4-8 D1U86 1K PSON# PSON# S8 VSB load S8 FET, BJT, wire or switch(debounced) to turn on 12V main output RTN FET, BJT, wire or switch(debounced) to turn on 12V main output 1K R2 Standby Shutdown Main Shutdown D1U86 RTN NOTES Main Output: Current share is achieved using the droop method. Nominal output voltage (12.30V) is achieved at 1A load and output voltage drops at a rate of 7.83mv per amp increase. Startup of parallel power supplies is not internally synchronized. If more than 460W combined power is needed, start-up synchronization must be provided by using a common PS_ON signal. To account for ±10% full load current sharing accuracy and the reduction in full load output voltage due to droop, available output power must be derated by 15% when units are operated in parallel. Internal ORing FETs are provided. Standby output can be tied together for redundancy but total combined output power must not exceed 30W, Internal MOSFET ORing devices are used. www.murata-ps.com/support D1U86G-W-460-12-HxxDC.A03 Page 4 of 5 D1U86G-W-460-12-HxxDC Series 86mm 1U Front End AC-DC Power Supply Converter MECHANICAL DIMENSIONS Airflow Back to Front Airflow Front to Back AC input connector: IEC 320-C14 3.4"W x 7.75"L x 1.57"H [86.4mm x 196.85mm x 39.9mm] MATING CONNECTOR Part Number Molex 45984-1122 FCI 51761-10002406AA Description Right Angle Right Angle OPTIONAL ACCESSORIES Description Part Number 12V D1U86G Output Connector Card D1U86G-12-CONC APPLICATION NOTES Document Number Description TBD D1U86G Output Connector Card TBD D1U86G Communication Protocol Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2013 Murata Power Solutions, Inc. www.murata-ps.com/support D1U86G-W-460-12-HxxDC.A03 Page 5 of 5