2.0x1.25mm SMD CHIP LED LAMP Part Number: APHBM2012QBDSURKC ATTENTION Blue Hyper Red OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 2.0mmx1.25mm SMD LED, 0.45mm max. thickness. z The Blue source color devices are made with InGaN z Bi -color, low power consumption. Light Emitting Diode. z The Hyper Red source color devices are made with z Wide viewing angle. z Ideal for backlight and indicator. AlGaInP on GaAs substrate Light Emitting Diode. z Electrostatic discharge and power surge could damage z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. the LEDs. z It is recommended to use a wrist band or anti- z RoHS compliant. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAJ8666 REV NO: V.8A DATE: NOV/18/2016 PAGE: 1 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203010215 Selection Guide Part No. Emitting Color (Material) Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. Typ. 40 80 *40 *80 120 250 *40 *80 2θ1/2 Blue (InGaN) APHBM2012QBDSURKC Water Clear Hyper Red (AlGaInP) 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Blue Hyper Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 460 645 nm IF=20mA Blue Hyper Red 465 630 nm IF=20mA Spectral Line Half-width Blue Hyper Red 25 28 nm IF=20mA C Capacitance Blue Hyper Red 100 35 pF VF=0V;f=1MHz VF [2] Forward Voltage Blue Hyper Red 3.3 1.95 4 2.5 V IF=20mA IR Reverse Current Blue Hyper Red 50 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Blue Hyper Red Units Power dissipation 120 75 mW DC Forward Current 30 30 mA Peak Forward Current [1] 150 185 mA Electrostatic Discharge Threshold (HBM) 250 3000 V Reverse Voltage 5 Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C V Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAJ8666 REV NO: V.8A DATE: NOV/18/2016 PAGE: 2 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203010215 APHBM2012QBDSURKC Blue SPEC NO: DSAJ8666 REV NO: V.8A DATE: NOV/18/2016 PAGE: 3 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203010215 Hyper Red SPEC NO: DSAJ8666 REV NO: V.8A DATE: NOV/18/2016 PAGE: 4 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203010215 APHBM2012QBDSURKC Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions SPEC NO: DSAJ8666 REV NO: V.8A DATE: NOV/18/2016 PAGE: 5 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203010215 PACKING & LABEL SPECIFICATIONS APHBM2012QBDSURKC Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAJ8666 REV NO: V.8A DATE: NOV/18/2016 PAGE: 6 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203010215