0.65X0.35mm SMD CHIP LED LAMP (0.2mm Height) Part Number: APG0603SYC-TT Super Bright Yellow Features Description z 0.65mmX0.35mm SMD LED,0.2mm thickness. The Super Bright Yellow source color devices are made z Low power consumption. with AlGaInP on GaAs substrate Light Emitting Diode. z Wide viewing angle. z Compatible with automatic placement equipment. z Package:4000pcs/reel. z Moisture sensitivity level : level 2. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAO2862 REV NO: V.4B DATE: MAY/12/2016 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203014743 Selection Guide Part No. Emitting Color (Material) APG0603SYC-TT Lens Type Super Bright Yellow (AlGaInP) Water Clear Viewing Angle [1] Iv (mcd) [2] @ 10mA Min. Typ. 2θ1/2 10 30 140° Notes: 1. θ1 / 2 is the angle from optical centerline where the luminous intensity is 1 / 2 of the optical peak value. 2. Luminous intensity / luminous Flux: + / -15%. 3. Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Super Bright Yellow λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 591 nm IF=10mA Super Bright Yellow 589 nm IF=10mA Spectral Line Half-width Super Bright Yellow 15 nm IF=10mA VF [2] Forward Voltage Super Bright Yellow 2.01 2.4 V IF=10mA IR Reverse Current Super Bright Yellow 10 uA VR=5V Notes: 1. Wavelength: + / -1nm. 2. Forward Voltage: + / -0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 48 mW DC Forward Current 20 mA Peak Forward Current [1] 100 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. 1 / 10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAO2862 REV NO: V.4B DATE: MAY/12/2016 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203014743 Super Bright Yellow APG0603SYC-TT Spatial Distribution -15° 1.0 0° Ta = 25 °C 15° -30° 30° 0.8 -45° 45° 0.6 60° -60° 0.4 -75° -1.2 -90° -1.0 75° 0.2 -0.8 -0.6 -0.4 -0.2 0.0 0.0 0.2 0.4 0.6 0.8 1.0 90° 1.2 SPEC NO: DSAO2862 REV NO: V.4B DATE: MAY/12/2016 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203014743 APG0603SYC-TT Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAO2862 REV NO: V.4B DATE: MAY/12/2016 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203014743 PACKING & LABEL SPECIFICATIONS APG0603SYC-TT Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAO2862 REV NO: V.4B DATE: MAY/12/2016 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203014743