TI1 DAC811JPG4 Microprocessor-compatible 12-bit digital-to-analog converter Datasheet

®
DAC811
For most current data sheet and other product
information, visit www.burr-brown.com
Microprocessor-Compatible
12-BIT DIGITAL-TO-ANALOG CONVERTER
FEATURES
● SINGLE INTEGRATED CIRCUIT CHIP
● MICROCOMPUTER INTERFACE:
Double-Buffered Latch
● VOLTAGE OUTPUT: ±10V, ±5V, +10V
● MONOTONICITY GUARANTEED OVER
TEMPERATURE
● ±1/2LSB MAXIMUM NONLINEARITY OVER
TEMPERATURE
● GUARANTEED SPECIFICATIONS AT ±12V
AND ±15V SUPPLIES
● TTL/5V CMOS-COMPATIBLE LOGIC
INPUTS
DESCRIPTION
The DAC811 is a complete, single-chip integratedcircuit, microprocessor-compatible, 12-bit digital-toanalog converter. The chip combines a precision voltage reference, microcomputer interface logic, and
double-buffered latch, in a 12-bit D/A converter with
a voltage output amplifier. Fast current switches and a
laser-trimmed thin-film resistor network provide a
highly accurate and fast D/A converter.
Input gating logic is designed so that loading the last
nibble or byte of data can be accomplished simultaneously with the transfer of data (previously stored in
adjacent latches) from adjacent input latches to the
D/A latch. This feature avoids spurious analog output
values while using an interface technique that saves
computer instructions.
The DAC811 is laser trimmed at the wafer level and
is specified to ±1/4LSB maximum linearity error (B
and K grades) at 25°C and ±1/2LSB maximum over
the temperature range. All grades are guaranteed monotonic over the specification temperature range.
The DAC811 is available in six performance grades
and three package types. DAC811J and K are specified over the temperature ranges of 0°C to +70°C;
DAC811A and B are specified over –25°C to +85°C;
DAC811J and K are packaged in a reliable 28-pin
plastic DIP or plastic SO package, while DAC811A
and B are available in a 28-pin 0.6" wide dual-inline
hermetically sealed ceramic side-brazed package (H
package).
Microcomputer interfacing is facilitated by a doublebuffered latch. The input latch is divided into three
4-bit nibbles to permit interfacing to 4-, 8-, 12-, or
16-bit buses and to handle right-or left-justified data.
The 12-bit data in the input latches is transferred to the
D/A latch to hold the output value.
4 MSBs
4 LSBs
SJ
Input Latch
Input Latch
Input Latch
RF
10V
D/A Latch
RF
12-Bit D/A Converter
RBPO
Voltage Reference
VOUT
BPO
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111
Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
®
© 1983 Burr-Brown Corporation
SBAS144
PDS-503L
1
Printed in U.S.A. April, 2000
DAC811
SPECIFICATIONS
At TA = +25°C. ±VCC = 12V or 15V, unless otherwise noted.
DAC811AH, JP, JU
PARAMETER
MIN
DIGITAL INPUT
Resolution
Codes(1)
Digital Inputs Over Temperature Range(2)
VIH
VIL
IIH, VI = +2.7V
IIL, VI = +0.4V
Digital Interface Timing Over Temperature Range
tWP, WR Pulse Width
tAW1, NX and LDAC Valid to End of WR
tDW, Data Valid to End of WR
tDH, Data Valid Hold Time
TYP
MAX
+15
+0.8
+10
±20
±10
±5
±5
±1/2
Guaranteed
✻
✻
±1/2
±3/4
±0.2
±0.15
Bits
✻
✻
✻
✻
VDC
VDC
µA
µA
ns
ns
ns
ns
±1/4
±1/2
✻
✻
LSB
LSB
%
% of FSR(5)
✻
✻
✻
% of FSR/%VCC
% of FSR/%VCC
% of FSR/%VDD
±30
±10
±10
±3/4
±10
±5
±5
±1/4
✻
±20
±7
±7
±1/2
ppm/°C
ppm of FSR/°C
ppm of FSR/°C
LSB
4
4
✻
✻
✻
✻
✻
✻
µs
µs
µs
V/µs
✻
✻
✻
0 to +10
±5, ±10
V
V
mA
Ω
✻
✻
✻
0.2
Indefinite
+11.4
–11.4
+4.5
✻
±1/8
±1/4
✻
✻
✻
✻
✻
✻
±0.003
±0.006
±0.0015
SETTLING TIME(6) (to within ±0.01% of FSR of Final Value; 2kΩ load)
For Full Scale Range Change, 20V Range
3
10V Range
3
For 1LSB Change at Major Carry(7)
1
Slew Rate(6)
8
12
+6.2
+2
UNITS
✻
✻
✻
✻
50
50
80
0
±5
MAX
✻
+2
0
DRIFT (Over Specification Temperature Range)
Gain
Unipolar Offset
Bipolar Zero
Linearity Error Over Temperature Range
Monotonicity Over Temperature Range
POWER SUPPLY REQUIREMENTS
Voltage: +VCC
–VCC
VDD
Current (no load): +VCC
–VCC
VDD
Potential at DCOM with Respect to ACOM(9)
Power Dissipation
TYP
12
±1/4
±1/2
±0.1
±0.05
Guaranteed
±0.001
±0.002
±0.0005
REFERENCE VOLTAGE
Voltage
Source Current Available for External Loads
Temperature Coefficient
Short Circuit to Common Duration
MIN
USB, BOB
ACCURACY
Linearity Error
Differential Linearity Error
Gain Error(3)
Offset Error(3, 4)
Monotonicity
Power Supply Sensitivity: +VCC
–VCC
VDD
ANALOG OUTPUT
Voltage Range (±VCC = 15V)(8): Unipolar
Bipolar
Output Current
Output Impedance (at DC)
Short Circuit to Common Duration
DAC811BH, KP, KU
+6.3
+6.4
±10
Indefinite
±30
+15
–15
+5
+16
–23
+8
±0.5
625
+16.5
–16.5
+5.5
+25
–35
+15
✻
✻
✻
✻
✻
800
✻
✻
±10
✻
±20
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
TEMPERATURE RANGE
Specification: J, K
A, B
R, S
0
–25
–65
+70
+85
+150
✻
✻
✻
✻
✻
✻
Storage: J, K
A, B, R, S
–60
–65
+100
+150
✻
✻
✻
✻
V
mA
ppm/°C
VDC
VDC
VDC
mA
mA
mA
V
mW
°C
°C
°C
°C
°C
°C
✻ Specification same as DAC811AH, JP, JU.
NOTES: (1) USB = unipolar straight binary; BOB = bipolar offset binary. (2) TTL, LSTTL and 54/74 HC compatible. (3) Adjustable to zero with external trim
potentiometer. (4) Error at input code 00016 for both unipolar and bipolar ranges. (5) FSR means full scale range and is 20V for the ±10V range. (6) Maximum
represents the 3σ limit. Not 100% tested for this parameter. (7) At the major carry, 7FF16 to 80016 and 80016 to 7FF16. (8) Minimum supply voltage required for ±10V
output swing is ±13.5V. Output swing for ±11.4V supplies is at least –8V to +8V. (9) The maximum voltage at which ACOM and DCOM may be separated without
affecting accuracy specifications.
®
DAC811
2
PIN DESCRIPTIONS
PIN
ABSOLUTE MAXIMUM RATINGS
NAME
FUNCTION
1
+VDD
Logic supply, +5V.
2
WR
Write, command signal to load latches. Logic low
loads latches.
3
LDAC
Load D/A converter, enables WR to load the D/A
latch. Logic low enables.
4
NA
Nibble A, enables WR to load input latch A (the
most significant nibble). Logic low enables.
5
NB
Nibble B, enables WR to load input latch B. Logic
low enables.
6
NC
Nibble C, enables WR to load input latch C (the
least significant nibble). Logic low enables.
7
D11
Data bit 12, MSB, positive true.
8
D10
Data bit 11.
9
D9
Data bit 10.
10
D8
Data bit 9.
11
D7
Data bit 8.
12
D6
Data bit 7.
13
D5
Data bit 6.
+VCC ................................................................................................................................ 0 to +18V
–VCC to ACOM .......................................................................... 0 to –18V
VDD to DCOM .............................................................................. 0 to +7V
VDD to ACOM ...................................................................................... ±7V
ACOM to DCOM .................................................................................. ±7V
Digital Inputs (Pins 2–14, 16–19) to DCOM ...................... –0.4V to +18V
External Voltage Applied to 10V Range Resistor ............................ ±12V
Ref Out ............................................................. Indefinite Short to ACOM
External Voltage Applied to DAC Output ................................ –5V to +5V
Power Dissipation ........................................................................ 1000mW
Lead Temperature (soldering, 10s) ............................................... +300°C
Max Junction Temperature ............................................................ +165°C
Thermal Resistance, θJ-A: Plastic DIP and SOIC ....................... 100°C/W
Ceramic DIP .................................................................................. 65°C/W
NOTE: Stresses above those listed above may cause permanent damage to
the device. Exposure to absolute maximum conditions for extended periods
may affect device reliability.
ELECTROSTATIC
DISCHARGE SENSITIVITY
14
D4
Data bit 5.
15
DCOM
Digital common, VDD supply return.
16
D0
Data bit 1, LSB.
17
18
19
20
21
22
23
24
25
26
27
D1
D2
D3
+VCC
–VCC
Gain Adj
ACOM
VOUT
10V Range
SJ
BPO
Data bit 2.
Data bit 3.
Data bit 4.
Analog supply input, +15V or +12V.
Analog supply input, –15V or –12V.
To externally adjust gain.
Analog common, ±VCC supply return.
D/A converter voltage output.
Connect to pin 24 for 10V range.
Summing junction of output amplifier.
Bipolar offset. Connect to pin 26 for bipolar
operation.
28
Ref Out
6.3V reference output.
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE/ORDERING INFORMATION
PRODUCT
MINIMUM
RELATIVE
ACCURACY
(LSB)
DIFFERENTIAL
LINEARITY
(LSB)
DAC811AH
DAC811JP
DAC811JU
±1/2 LSB
±1/2 LSB
±1/2 LSB
3/4
3/4
3/4
"
DAC811KP
DAC811KU
PACKAGE
PACKAGE
DRAWING
NUMBER
SPECIFICATION
TEMPERATURE
RANGE
ORDERING
NUMBER(1)
TRANSPORT
MEDIA
CERDIP-28
DIP-28
SO-28
149
215
217
–25°C to +85°C
0°C to +70°C
0°C to +70°C
DAC811AH
DAC811JP
DAC811JU
Rails
Rails
Rails
DAC811JU/1K
DAC811KP
DAC811KU
Tape and Reel
Rails
Rails
"
"
"
"
"
±1/4 LSB
±1/4 LSB
1/2
1/2
DIP-28
SO-28
215
217
0°C to +70°C
0°C to +70°C
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /1K indicates 1000 devices per reel). Ordering 1000 pieces
of “DAC811JU/1K” will get a single 1000-piece Tape and Reel.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
®
3
DAC811
TIMING DIAGRAMS
Write Cycle #2
Load second rank from first rank: NA , NB , N C = 1
Write Cycle #1
Load first rank from Data Bus: LDAC = 1
tAW
tAW
LDAC
N A , NB , N C
tWP
tDW
WR
DB11 –DB0
tSET
tWP
tDH
WR
±1/2LSB
DISCUSSION OF
SPECIFICATIONS
DRIFT
Gain drift is a measure of the change in the full scale range
(FSR) output over the specification temperature range. Drift is
expressed in parts per million per degree centigrade
(ppm/°C). Gain drift is established by testing the full scale
range value (e.g., +FS minus –FS) at high temperature, +25°C,
and low temperature, calculating the error with respect to the
+25°C value, and dividing by the temperature change.
INPUT CODES
The DAC811 accepts positive-true binary input codes.
DAC811 may be connected by the user for any one of the
following codes: USB (unipolar straight binary), BOB (bipolar offset binary) or, using an external inverter on the
MSB line, BTC (binary two’s complement). See Table I.
DIGITAL INPUT
Unipolar offset drift is a measure of the change in output
with all 0s on the input over the specification temperature
range. Offset is measured at high temperature, +25°C, and
low temperature. The offset drift is the maximum change in
offset referred to the +25°C value, divided by the temperature change. It is expressed in parts per million of full scale
range per degree centigrade (ppm of FSR/°C).
ANALOG OUTPUT
USB
Unipolar
Straight
Binary
BOB
Bipolar
Offset
Binary
BTC(1)
Binary
Two’s
Complement
+ Full Scale
+ 1/2 Full Scale
+ 1/2 Full Scale – 1LSB
Zero
+ Full Scale
Zero
–1LSB
– Full Scale
–1LSB
– Full Scale
+ Full Scale
Zero
Bipolar zero drift is measured at a digital input of 80016, the
code that gives zero volts output for bipolar operation.
NOTE: (1) Invert MSB of the BOB code with external inverter to obtain BTC code.
SETTLING TIME
Settling time is the total time (including slew time) for the
output to settle within an error band around its final value
after a change in input. Three settling times are specified to
±0.01% of full scale range (FSR): two for maximum full
scale range changes of 20V and 10V, and one for a 1LSB
change. The 1LSB change is measured at the major carry
(7FF16 to 80016 and 80016 to 7FF16), the input transition at
which worst-case settling time occurs.
MSB
LSB
↓
↓
111111111111
100000000000
011111111111
000000000000
TABLE I. Digital Input Codes.
LINEARITY ERROR
Linearity error as used in D/A converter specifications by
Burr-Brown is the deviation of the analog output from a
straight line drawn between the end points (inputs all 1s and
all 0s). The DAC811 linearity error is specified at ±1/4LSB
(max) at +25°C for B and K grades, and ±1/2LSB (max) for
A and J grades.
REFERENCE SUPPLY
DAC811 contains an on-chip 6.3V reference. This voltage
(pin 28) has a tolerance of ±0.1V. The reference output may
be used to drive external loads, sourcing at least 2mA. This
current should be constant for best performance of the D/A
converter.
DIFFERENTIAL LINEARITY ERROR
Differential linearity error (DLE) is the deviation from a
1LSB output change from one adjacent state to the next. A
DLE specification of 1/2LSB means that the output step size
can range from 1/2LSB to 3/2LSB when the input changes
from one state to the next. Monotonicity requires that DLE
be less than 1LSB over the temperature range of interest.
POWER SUPPLY SENSITIVITY
Power supply sensitivity is a measure of the effect of a
power supply change on the D/A converter output. It is
defined as a percent of FSR output change per percent of
change in either the positive, negative, or logic supply
voltages about the nominal voltages. Figure 1 shows typical
power supply rejection versus power supply ripple frequency.
MONOTONICITY
A D/A converter is monotonic if the output either increases
or remains the same for increasing digital inputs. All grades
of DAC811 are monotonic over their specification temperature range.
®
DAC811
4
The D/A latch is controlled by LDAC and WR. LDAC and
WR are internally NORed so that the latches transmit data to
the D/A switches when both LDAC and WR are at logic 0.
When either LDAC or WR are at logic 1, the data is latched
in the D/A latch and held until LDAC and WR go to logic 0.
Percent of FSR per Percent of
Change of Power Supply Voltage
1
–VCC
0.1
V DD
0.01
All latches are level-triggered. Data present when the control signals are logic 0 will enter the latch. When any one of
the control signals returns to logic 1, the data is latched.
Table II is a truth table for all latches.
+VCC
0.001
0.0001
10
100
1k
10k
1M
100k
Frequency (Hz)
FIGURE 1. Power Supply Rejection vs Power Supply Ripple
Frequency.
WR
NA
NB
NC
LDAC
1
0
0
0
0
0
X
0
1
1
1
0
X
1
0
1
1
0
X
1
1
0
1
0
X
1
1
1
0
0
OPERATION
No operation
Enables input latch 4MSBs
Enables input latch 4 middle bits
Enables input latch 4LSBs
Loads D/A latch from input latches
Makes all latches transparent
“X” = Don’t care.
OPERATION
TABLE II. DAC813 Interface Logic Truth Table.
DAC811 is a complete single IC chip 12-bit D/A converter.
The chip contains a 12-bit D/A converter, voltage reference,
output amplifier, and microcomputer-compatible input logic
as shown in Figure 2.
GAIN AND OFFSET ADJUSTMENTS
Figures 3 and 4 illustrate the relationship of offset and gain
adjustments to unipolar and bipolar D/A converter output.
INTERFACE LOGIC
Input latches A, B, and C hold data temporarily while a
complete 12-bit word is assembled before loading into the
D/A register. This double-buffered organization prevents the
generation of spurious analog output values. Each register is
independently addressable.
OFFSET ADJUSTMENT
For unipolar (USB) configurations, apply the digital input
code that should produce zero voltage output, and adjust the
offset potentiometer for zero output. For bipolar (BOB,
BTC) configurations, apply the digital input code that should
produce the maximum negative output voltage and adjust
the offset potentiometer for minus full scale voltage. Example: If the full scale range is connected for 20V, the
maximum negative output voltage is –10V. See Table III for
corresponding codes.
These input latches are controlled by NA, NB, NC, and WR.
NA, NB, and NC are internally NORed with WR so that the
input latches transmit data when both NA (or NB, NC ) and
WR are at logic 0. When either NA, (NB, NC ) or WR go to
logic 1, the input data is latched into the input registers and
held until both NA (or NB, NC ) and WR go to logic 0.
MSB D11
7
WR
8
9
D8
D7
10
11
12
13
D4
D3
14
19
D0
18
17
16
RBPO
2
4-Bit Latch, A
NA
4
NB
5
LSB
4-Bit Latch, B
4-Bit Latch, C
27
BPO
26
SJ
25
10V
Range
24
VOUT
23
ACOM
RF
NC
6
LDAC
3
12-Bit D/A Latch
RF
12-Bit D/A Converter
Reference
Ref Out
28
FIGURE 2. DAC811 Block Diagram.
®
5
DAC811
±12V OPERATION
+ Full Scale
The DAC811 is fully specified for operation on ±12V power
supplies. However, in order for the output to swing to ±10V,
the power supplies must be ±13.5V or greater. When operating with ±12VB supplies, the output swing should be
restricted to ±8V in order to meet specifications.
Range of
Gain Adjust
Full Scale Range
Analog Output
1LSB
Range of
Offset Adj.
LOGIC INPUT COMPATIBILITY
The DAC811 digital inputs are TTL, LSTTL, and 54/74HC
CMOS-compatible over the operating range of VDD. The
input switching threshold remains at the TLL threshold over
the supply range.
Gain Adjust
Rotates the Line
All Bits
Logic 0
All Bits
Logic 1
The logic input current over temperature is low enough to
permit driving the DAC811 directly from the outputs of
4000B and 54/74C CMOS devices.
Digital Input
Offset Adjust Translates the Line
Resistors of 47Ω should be placed in series with D0 through
D11, WR, NA, NB, NC and LDAC if edges are <10ns or if
the logic input is driven below ground by undershoot.
FIGURE 3. Relationship of Offset and Gain Adjustments
for a Unipolar D/A Converter.
INSTALLATION
+ Full Scale
POWER SUPPLY CONNECTIONS
For optimum performance and noise rejection, power supply
decoupling capacitors should be added as shown in Figure 5.
Analog Output
1LSB
Range of
Gain Adjust
Full Scale
Range
All Bits
Logic 0
Bipolar V
Offset
These capacitors (1µF tantalum recommended) should be
located close to the DAC811.
Gain Adjust
Rotates the Line
MSB on All
Others Off
All Bits
Logic 1
Range of
Offset Adjust
VDD
– Full Scale
Offset Adj.
Translates
the Line
≈ ±0.4%
1µF
1
28
V DD
2
BPO
27
3
Summing
Junction
26
Digital Input
4
FIGURE 4. Relationship of Offset and Gain Adjustments
for a Bipolar D/A Converter.
ANALOG OUTPUT
DIGITAL INPUT
0 to +10V
±5V
±10V
MSB
LSB
↓
↓
111111111111
100000000000
011111111111
000000000000
LSB
+9.9976V
+5V
+4.9976V
0V
2.4mV
+4.9976V
0V
–0.0024V
–5V
2.44mV
+9.9951V
0V
–0.0049V
–10V
4.88mV
GAIN ADJUSTMENT
For either unipolar or bipolar configurations, apply the
digital input that should give the maximum positive voltage
output. Adjust the gain potentiometer for this positive full
scale voltage. See Table III for positive full scale voltages.
10k Ω to
100kΩ
25
VOUT
24
6
ACOM
23
7
Gain Adjust
22
8
–VCC
21
–VCC
9
+VCC
20
+VCC
+VCC
3.9MΩ
10
19
11
18
0.0022µF
12
17
1µF
13
16
DCOM
10k Ω to
100kΩ
1µF
15
FIGURE 5. Power Supply, Gain, and Offset Potentiometer
Connections.
®
DAC811
–VCC
1MΩ
5
14
TABLE III. Digital Input/Analog Output.
Connect for
Bipolar Operation
6
DAC811 features separate digital and analog power supply
returns to permit optimum connections for low noise and
high speed performance. The analog common (pin 23) and
digital common (pin 15) should be connected together at one
point. Separate returns minimize current flow in low level
signal paths if properly connected. Logic return currents are
not added into the analog signal return path. A ±0.5V
difference between ACOM and DCOM is permitted for
specified operation. High frequency noise on DCOM with
respect to ACOM may permit noise to be coupled through to
the analog output; therefore, some caution is required in
applying these common connections.
From Voltage
Reference
From D/A
Converter
180kΩ
26
Summing Junction
25
10V Range
24
VOUT
23
Analog Common
4.26kΩ
OUTPUT
RANGE
DIGITAL
INPUT CODES
CONNECT
PIN 25 TO
CONNECT
PIN 27 TO
0 to +10V
±5
±10V
USB
BOB or BTC
BOB or BTC
24
24
NC
23
26
26
TABLE IV. Output Range Connections.
APPLICATIONS
MICROCOMPUTER BUS INTERFACING
The DAC811 interface logic allows easy interface to microcomputer bus structures. The control signal WR is derived
from external device select logic and the I/O Write or
Memory Write (depending upon the system design) signals
from the microcomputer.
The latch enable lines NA, NB, NC and LDAC determine
which of the latches are enabled. It is permissible to enable
two or more latches simultaneously, as shown in some of the
following examples.
The double-buffered latch permits data to be loaded into the
input latches of several DAC811s and later strobed into the
D/A latch of all D/As, simultaneously updating all analog
outputs. All the interface schemes shown below use a base
address decoder. If blocks of memory are used, the base
address decoder can be simplified or eliminated altogether.
For instance, if half the memory space is unused, address
line A15 of the microcomputer can be used as the chip select
control.
100kΩ
12kΩ
3.9MΩ
Bipolar Offset
FIGURE 7. Output Amplifier Voltage Range Scaling Circuit.
EXTERNAL OFFSET AND GAIN ADJUSTMENT
Offset and Gain may be trimmed by installing external
Offset and Gain potentiometers. Connect these potentiometers as shown in Figure 5. TCR of the potentiometers
should be 100ppm/°C or less. The 1MΩ and 3.9MΩ resistors (20% carbon or better) should be located close to the
DAC811 to prevent noise pickup. If it is not convenient to
use these high value resistors, an equivalent “T” network, as
shown in Figure 6, may be substituted in each case. The
Gain Adjust (pin 22) is a high impedance point and a
0.001µF to 0.01µF ceramic capacitor should be connected
from this pin to Analog Common to reduce noise pickup in
all applications, including those not employing external gain
adjustment. Excessive capacitance on the Gain Adjust or
Offset Adjust pin may affect slew rate and settling time.
100kΩ
27
4.26kΩ
The Analog Common is the high quality return for the D/A
converter and should be connected directly to the analog
reference point of the system. The load driven by the output
amplifier should be returned to the Analog Common.
1MΩ
5.36kΩ
180kΩ
10kΩ
4-BIT INTERFACE
An interface to a 4-bit microcomputer is shown in Figure 8.
Each DAC811 occupies four address locations. A 74LS139
provides the two-to-four decoder and selects it with the base
address. Memory Write (WR) of the microcomputer is
connected directly to the WR pin of the DAC811. An 8205
decoder is an alternative to the 74LS139.
FIGURE 6. Equivalent Resistances.
OUTPUT RANGE CONNECTIONS
Internal scaling resistors provided in the DAC811 may be
connected to produce bipolar output voltage ranges of ±10V
and ±5V or a unipolar output voltage range of 0 to +10V.
The 20V range (±10V bipolar range) is internally connected.
Refer to Figure 7. Connections for the output ranges are
listed in Table IV.
®
7
DAC811
8-BIT INTERFACE
The control logic of DAC811 permits interfacing to rightjustified data formats, as illustrated in Figure 9. When a
12-bit D/A converter is loaded from an 8-bit bus, two bytes
of data are required. Figures 10 and 11 show an addressing
scheme for right-justified and left-justified data respectively.
The base address is decoded from the high-order address
bits. A0 and A1 address the appropriate latches. Note that
adjacent addresses are used. For the right-justified case,
X1016 loads the 8LSBs, and X0116 loads the 4MSBs and
simultaneously transfers input latch data to the D/A latch.
Addresses X0016 and X1116 are not used.
16
D0
10
D8
17
D1
DB0
DB1
9
D9
18
D2
DB2
8
D10
19
D3
Left-justified data is handled in a similar manner, shown in
Figure 11. The DAC811 still occupies two adjacent locations in the microcomputer's memory map.
7
D11
DB4
14
D4
DB5
13
D5
DB6
12
D6
DB7
11
D7
2
WR
3
LDAC
4
NA
5
NB
6
NC
DAC811
Microcomputer
DB3
WR
A15
DB3
D4
10
D8
17
D1
13
D5
9
D9
18
D2
12
D6
8
D10
19
D3
11
D7
7
D11
2
WR
WR
AN
Base
Address
Decoder
A2
1
Y3
A1
3
A1
Y2
A0
2
A0
Y1
Y0
7
6
5
4
FIGURE 10. Right-Justified Data Bus Interface.
X
X D11 D10 D9 D8
3
LDAC
12
D6
11
D7
10
D8
16
D0
4
NA
5
NB
6
NC
9
D9
17
D1
DB4
8
D10
DB5
18
D2
DB6
7
D11
DB7
19
D3
2
WR
3
LDAC
4
NA
5
NB
6
NC
DB3
WR
A2
D7 D6 D5 D4 D3 D2 D1 D0
D3 D2 D1 D0
D5
DB2
A1
a. Right-Justified
D11 D10 D9 D8 D7 D6 D5 D4
D4
13
DB1
A15
X
14
DB0
FIGURE 8. Addressing and Control for 4-Bit Microcomputer Interface.
X
CS
A0
CS
(Chip
Select)
EN
1/2
74LS139
A2
A1
Microcomputer
Microcomputer
DB2
D0
14
X
X
X
X
A0
Base
Address
Decoder
CS
b. Left-Justified
FIGURE 11. Left-Justified Data Bus Interface.
FIGURE 9. 12-Bit Data Format for 8-Bit Systems.
®
DAC811
DAC811
DB1
16
DAC811
DB0
Base
Address
Decoder
8
INTERFACING MULTIPLE DAC811s
IN 8-BIT SYSTEMS
Many applications, such as automatic test systems, require
that the outputs of several D/A converters be updated simultaneously. The interface shown in Figure 12 uses a 74LS138
decoder to decode a set of eight adjacent addresses, to load
the input latches of four DAC811s. The example shows a
right-justified data format.
eight address spaces for other uses. Incorporate A3 into the
base address decoder, remove the inverter, connect the
common LDAC line to NC of D/A #4, and connect D1 of the
74LS138 to +5V.
12- AND 16-BIT MICROCOMPUTER INTERFACE
For this application, the input latch enable lines, NA, NB and
NC, are tied low, causing the latches to be transparent. The
D/A latch, and therefore DAC811, is selected by the address
decoder and strobed by WR.
A ninth address using A3 causes all DAC811s to be updated
simultaneously. If a particular DAC811 is always loaded
last—for instance, D/A #4—A3 is not needed, thus saving
WR
A15
A4
WR
Base
Address
Decoder
LDAC
CS
NC
DAC811
(1)
NB
NA
A3
A3
Microcomputer
74LS138
4
5
6
15
G2A
G2B
G1
Y0
Y1
Y2
14
13
12
A2
A1
A0
3
0
0
0
0
Load 8 LSB – D/A #1
0
0
0
1
Load 4 MSB – D/A #1
LDAC
0
0
1
0
Load 8 MSB – D/A #2
0
0
1
1
Load 4 MSB – D/A #2
NB
0
1
0
0
Load 8 MSB – D/A #3
NA
0
1
0
1
Load 4 MSB – D/A #3
0
1
1
0
Load 8 MSB – D/A #4
0
1
1
1
Load 4 MSB – D/A #4
1
X
X
X
Load D/A Latch—All D/A
NC
DAC811
(2)
2
1
B
Y6
A
Y7
WR
LDAC
Y5
C
9
7
OPERATION
WR
Y3 11
Y4 10
ADDRESS BUS
A2
A1
A0
NC
DAC811
(4)
NB
NA
FIGURE 12. Interfacing Multiple DAC811s to an 8-Bit Bus.
®
9
DAC811
PACKAGE OPTION ADDENDUM
www.ti.com
3-Jul-2009
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
DAC811AH
NRND
CDIP SB
JD
28
1
Green (RoHS &
no Sb/Br)
AU
N / A for Pkg Type
DAC811BH
NRND
CDIP SB
JD
28
1
Green (RoHS &
no Sb/Br)
AU
N / A for Pkg Type
DAC811JP
NRND
PDIP
NTD
28
13
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
DAC811JPG4
NRND
PDIP
NTD
28
13
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
DAC811JU
ACTIVE
SOIC
DW
28
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
DAC811JU/1K
ACTIVE
SOIC
DW
28
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
DAC811JU/1KE4
ACTIVE
SOIC
DW
28
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
DAC811JUG4
ACTIVE
SOIC
DW
28
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
DAC811KP
NRND
PDIP
NTD
28
13
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
DAC811KPG4
NRND
PDIP
NTD
28
13
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
DAC811KU
ACTIVE
SOIC
DW
28
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
DAC811KUG4
ACTIVE
SOIC
DW
28
20
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
3-Jul-2009
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
DAC811JU/1K
Package Package Pins
Type Drawing
SOIC
DW
28
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
1000
330.0
32.4
Pack Materials-Page 1
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
11.35
18.67
3.1
16.0
32.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DAC811JU/1K
SOIC
DW
28
1000
346.0
346.0
49.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
Similar pages