BELLING BL8025 1a 1.5mhz 6v synchronous buck converter Datasheet

BL8025
1A 1.5MHz 6V Synchronous Buck Converter
DESCRIPTION
FEATURES
The BL8025 is a high-efficiency, DC-to-DC stepdown switching regulators, capable of delivering up
to 1A of output current. The device operates from
an input voltage range of 2.6V to 6.0V and provides
an output voltage from 0.6V to VIN, making the
BL8025 ideal for low voltage power conversions.
Running at a fixed frequency of 1.5MHz allows the
use of small external components, such as ceramic
input and output caps, as well as small inductors,
while still providing low output ripples. This low
noise output along with its excellent efficiency
achieved by the internal synchronous rectifier,
making BL8025 an ideal green replacement for
large power consuming linear regulators. Internal
soft-start control circuitry reduces inrush current.
Short-circuit and thermal-overload protection
improves design reliability.
BL8025 is housed in a SOT23-5 Package
TYPICAL APPLICATION











High Efficiency: Up to 96%
Capable of Delivering 1A (Vin  3.3V)
1.5MHz Switching Frequency
No External Schottky Diode Needed
Low dropout 100% Duty operation
Internal Compensation and Soft-Start
Current Mode control
0.6V Reference for Low Output voltages
Logic Control Shutdown (Iq<1uA)
Thermal shutdown and UVLO
Available in SOT23-5
APPLICATIONS







Cellular phones
Digital Cameras
MP3 and MP4 players
Set top boxes
Wireless and DSL Modems
USB supplied Devices in Notebooks
Portable Devices
PIN OUT & MARKING
FB
4
5
SW
BL8025
VIN GND
3
2
1
GJYW
EN
SOT23-5
GJ: Product Code
YW: Date code (Year & Week)
www.belling.com.cn
1
BL8025
ORDERING INFORMATION
PART No.
BL8025CB5TR
PACKAGE
SOT23-5
Tape&Reel
3000/Reel
ABSOLUTE MAXIMUM RATING
Parameter
Value
Max Input Voltage
Max Operating Junction Temperature(Tj)
Ambient Temperature(Ta)
Maximum Power Dissipation
SOT23-5
Storage Temperature(Ts)
Lead Temperature & Time
ESD (HBM)
6.3V
125C
-40C – 85C
400mW
-40C - 150C
260C, 10S
>2000V
Note: Exceed these limits to damage to the device. Exposure to absolute maximum rating conditions may affect
device reliability.
RECOMMENDED WORK CONDITIONS
Parameter
Value
Input Voltage Range
Operating Junction Temperature(Tj)
Max. 6V
-20C –125C
ELECTRICAL CHARACTERISTICS
(VDD=5V, TA=25C)
Symbol
Parameter
VDD
Input Voltage Range
Vref
Feedback Voltage
Ifb
Feedback Leakage current
Iq
Quiescent Current
Conditions
Vin=5V
0.585
Active, Vfb=0.65, No Switching
Vin=2.7V to 5.5V
LdReg
Load Regulation
Iout=0.01 to 1A
Switching Frequency
PMOS Rdson
RdsonN
NMOS Rdson
Ilimit
Peak Current Limit
Iswlk
SW Leakage Current
Ienlk
EN Leakage Current
Vh_en
EN Input High Voltage
Vl_en
EN Input Low Voltage
www.belling.com.cn
Max
Unit
6.0
V
0.6
0.615
V
0.1
0.4
uA
40
Shutdown
Line Regulation
RdsonP
Typ
2.6
LnReg
Fsoc
Min
1.3
Vin  3.3V
Vout=5.5V,
EN=0V
1.2
VSW=0
or
5.5V,
uA
1
uA
0.04
0.2
%/V
0.1
0.2
%/A
1.5
1.7
MHz
280
350
mohm
190
250
mohm
1.5
2
A
10
uA
1
uA
1.5
V
0.4
2
V
BL8025
PIN DESCRIPTION
PIN #
1
2
3
NAME
VIN
GND
EN
4
FB
5
SW
DESCRIPTION
Supply voltage.
Ground
Enable pin for the IC. Drive the pin to high to enable the part, and low to disable
Feedback input. Connect an external resistor divider from the output to FB and
GND to set the output to a voltage between 0.6V and Vin
Inductor connection. Connect an inductor between SW and the regulator output.
ELECTRICAL PERFORMANCE
Tested under TA=25C, unless otherwise specified
Efficiency / Vout=3.3V
Efficiency
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
0%
0.001
www.belling.com.cn
VIN=6V
VIN=5V
VIN=4V
VIN=3.7V
0.01
0.1
Iout (A)
1
3
BL8025
Power up
Output Ripple and SW at 1A load
Vin=6V / Vout=3.3V
Ch1: Vin, Ch2: Vout, Ch3 EN
Ch1: Vin, Ch2: Vout, Ch3 SW, Ch4: I_inductor
BLOCK DIAGRAM
VIN
UVLO &
Thermal
shutdown
0.6V Ref
+
ISense
-
+
+
Comp
Network
Σ
-
EA
EN
PWM
Logic
AntiShootThrough
Driver
SW
Slope Comp
+
OSC
Vcomp
-
FB
www.belling.com.cn
4
GND
BL8025
DETAILED DESCRIPTION
The BL8025 high-efficiency switching regulator is a
small, simple, DC-to-DC step-down converter
capable of delivering up to 1A of output current.
The device operates in pulse-width modulation
(PWM) at 1.5MHz from a 2.6V to 5.5V input voltage
and provides an output voltage from 0.6V to VIN,
making the BL8025 ideal for on-board postregulation applications. An internal synchronous
rectifier improves efficiency and eliminates the
typical Schottky free-wheeling diode. Using the on
resistance of the internal high-side MOSFET to
sense switching currents eliminates current-sense
resistors, further improving efficiency and cost.
turns on. BL8025 utilizes a frequency fold-back
mode to prevent overheating during short-circuit
output conditions. The device enters frequency
fold-back mode when the FB voltage drops below
200mV, limiting the current to 1.5A (typ) and
reducing power dissipation. Normal operation
resumes upon removal of the short-circuit
condition.
Soft-start
BL8025 has a internal soft-start circuitry to reduce
supply inrush current during startup conditions.
When the device exits under-voltage lockout
(UVLO), shutdown mode, or restarts following a
thermal-overload event, the l soft-start circuitry
slowly ramps up current available at SW.
Loop Operation
BL8025 uses a PWM current-mode control scheme.
An open-loop comparator compares the integrated
voltage-feedback signal against the sum of the
amplified current-sense signal and the slope
compensation ramp. At each rising edge of the
internal clock, the internal high-side MOSFET turns
on until the PWM comparator terminates the on
cycle. During this on-time, current ramps up
through the inductor, sourcing current to the
output and storing energy in the inductor. The
current mode feedback system regulates the peak
inductor current as a function of the output voltage
error signal. During the off cycle, the internal highside P-channel MOSFET turns off, and the internal
low-side N-channel MOSFET turns on. The inductor
releases the stored energy as its current ramps
down while still providing current to the output.
UVLO and Thermal Shutdown
If VIN drops below 2.5V, the UVLO circuit inhibits
switching. Once VIN rises above 2.6V, the UVLO
clears, and the soft-start sequence activates.
Thermal-overload protection limits total power
dissipation in the device. When the junction
temperature exceeds TJ= +160°C, a thermal sensor
forces the device into shutdown, allowing the die to
cool. The thermal sensor turns the device on again
after the junction temperature cools by 15°C,
resulting in a pulsed output during continuous
overload conditions. Following a thermal-shutdown
condition, the soft-start sequence begins.
Design Procedure
Current Sense
Setting Output Voltages
An internal current-sense amplifier senses the
current through the high-side MOSFET during on
time and produces a proportional current signal,
which is used to sum with the slope compensation
signal. The summed signal then is compared with
the error amplifier output by the PWM comparator
to terminate the on cycle.
Output voltages are set by external resistors. The
FB_ threshold is 0.6V.
RTOP = RBOTTOM[(VOUT / 0.6) - 1]
Input Capacitor Selection
The input capacitor in a DC-to-DC converter reduces
current peaks drawn from the battery or other
input power source and reduces switching noise in
the controller. The impedance of the input
capacitor at the switching frequency should be less
than that of the input source so high-frequency
switching currents do not pass through the input
Current Limit
There is a cycle-by-cycle current limit on the highside MOSFET of 1.5A(typ). When the current
flowing out of SW exceeds this limit, the high-side
MOSFET turns off and the synchronous rectifier
www.belling.com.cn
5
BL8025
source. The output capacitor keeps output ripple
small and ensures control-loop stability. The output
capacitor must also have low impedance at the
switching frequency. Ceramic, polymer, and
tantalum capacitors are suitable, with ceramic
1) Place decoupling capacitors as close to the IC as
possible
2) Connect input and output capacitors to the
same power ground node with a star ground
configuration then to IC ground.
3) Keep the high-current paths as short and wide
as possible. Keep the path of switching current
(C1 to VIN and C1 to GND) short. Avoid vias in
the switching paths.
4) If possible, connect VIN, SW, and GND
separately to a large copper area to help cool
the IC to further improve efficiency and longterm reliability.
5) Ensure all feedback connections are short and
direct. Place the feedback resistors as close to
the IC as possible.
6) Route high-speed switching nodes away from
sensitive analog areas
exhibiting the lowest ESR and high-frequency
impedance. Output ripple with a ceramic output
capacitor is approximately as follows:
VRIPPLE = IL(PEAK)[1 / (2π x fOSC x COUT)]
If the capacitor has significant ESR, the output
ripple component due to capacitor ESR is as follows:
VRIPPLE(ESR) = IL(PEAK) x ESR
Application Information
Layout is critical to achieve clean and stable
operation. The switching power stage requires
particular attention. Follow these guidelines for
good PC board layout:
PACKAGE OUTLINE
Package
SOT23-5
Devices per reel
Package specification:
www.belling.com.cn
6
3000
Unit
mm
Similar pages