RoHS Compliant Serial ATA Flash Drive Specifications for SAFD 255 Apr 14, 2011 Version 1.2 Apacer Technology Inc. th th 4 Fl., 75 Xintai 5 Rd., Sec.1, Hsichih, New Taipei City, Taiwan 221 Tel: +886-2-2698-2888 www.apacer.com Fax: +886-2-2698-2889 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT Features: Standard Serial ATA 2.6 (Gen. 2) – Serial ATA 2.6 (Gen. 2) – SATA II, 3.0 Gbps – ATA-compatible command set Capacities – 8, 16, 32, 64 GB Performance* – Burst read/write: 300 MB/sec – Sustained read: up to 230 MB/sec – Sustained write: up to 175 MB/sec Intelligent endurance design – Built-in hardware ECC, enabling up to 14/28 bit correction per 1K bytes – Static wear-leveling scheme together with dynamical block allocation to significantly increase the lifetime of a flash device and optimize the disk performance – Flash bad-block management – S.M.A.R.T. – Power Failure Management – ATA Secure Erase – Trim Zero power data retention – No battery required for data storage Temperature ranges – Operation: Standard: 0°C to 70°C Extended Temperature: -40°C to 85°C – Storage: -40°C to 100°C Supply voltage – 5.0 V ± 5% Low power consumption* – Active mode: 535 [email protected] V – Idle mode: 94 [email protected] V Form factor – 2.5 inch Connector – 7-pin SATA male connector – 15-pin SATA power connector RoHS compliant NAND Flash Type: SLC *Varies from capacities. 1 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT Table of Contents 1. Product Description ................................................................................................. 3 1.1 Introduction .................................................................................................................................. 3 1.2 Functional Block Diagram........................................................................................................... 3 1.3 ATA Mode Support....................................................................................................................... 4 1.4 Capacity Specification ................................................................................................................. 4 1.5 Performance ................................................................................................................................. 4 1.6 Pin Assignments .......................................................................................................................... 5 2. Software Interface .................................................................................................... 7 2.1 Command Set ............................................................................................................................... 7 3. Flash Management ................................................................................................... 8 3.1 Error Correction/Detection.......................................................................................................... 8 3.2 Bad Block Management............................................................................................................... 8 3.3 Wear Leveling ............................................................................................................................... 8 3.4 Power Failure Management......................................................................................................... 8 3.5 ATA Secure Erase ........................................................................................................................ 8 3.6 S.M.A.R.T....................................................................................................................................... 9 3.7 TRIM............................................................................................................................................... 9 4. Environmental Specifications ............................................................................... 10 4.1 Environments ............................................................................................................................. 10 4.2 Mean Time Between Failures (MTBF) ...................................................................................... 10 4.3 Certification and Compliance ................................................................................................... 10 5. Electrical Characteristics ...................................................................................... 11 5.1 Operating Voltage ...................................................................................................................... 11 5.2 Power Consumption .................................................................................................................. 11 6. Physical Characteristics........................................................................................ 12 6.1 Plastic Housing .......................................................................................................................... 12 6.2 Metal Housing............................................................................................................................. 13 7. Product Ordering Information ............................................................................... 14 7.1 Product Code Designations ...................................................................................................... 14 7.2 Valid Combinations.................................................................................................................... 15 2 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT 1. Product Description 1.1 Introduction Apacer’s Serial ATA Flash Drive (SAFD) 255 is a solid-state disk (SSD) drive that contains a controller, embedded firmware, and flash media along with a male connector. Using single-level cell (SLC) NAND flash memory devices, the SAFD 255 interfaces with the host allowing data to be seamlessly transferred between the host and the flash devices. The SAFD 255 is designed with a single-chip controller, offering capacities of up to 64 gigabytes and providing full support for the SATA II high-speed interface standard. It can operate at burst access rates of up to 300 megabytes per second, which is much faster than any other solid-state or traditional SATA drive currently available on the market. In addition to buffer management through dynamical allocation, the SAFD 255 adopts the Apacer-specific static wear-leveling scheme to allow uniform use of all storage blocks, ensuring that the lifetime of a flash media can be significantly increased and the disk performance is optimized as well. The SAFD 255 provides the S.M.A.R.T. feature that follows the SATA Rev. 2.6, ATA/ATAPI-7 specifications and uses the standard SMART command B0h to read data from the drive. This feature protects the user from unscheduled downtime by monitoring and storing critical drive performance. 1.2 Functional Block Diagram The SAFD 255 includes a single-chip SATA II Controller and the flash media, as well as the SATA standard interface. The controller integrates the flash management unit with the controller itself to support multi-channel, multi-bank flash arrays. Figure 1-1 shows the functional block diagram. Figure 1-1 Apacer SAFD 255 block diagram 3 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT 1.3 ATA Mode Support The SAFD 255 provides ATA mode support as follows: 1.4 Up to PIO mode-4 Up to Multiword DMA mode-2 Up to UDMA mode-5 Capacity Specification Capacity specification of the SAFD 255 product family is available as shown in Table 1-1. It lists the specific capacity, the default numbers of logical cylinders and heads, and the number of logical sectors per track for each product line. Table 1-1 Capacity specification Capacity Total Bytes* Cylinders Heads Sectors Max LBA** 8 GB 7,913,816,064 15,334 16 63 15,456,672 16 GB 15,842,017,280 16,383 16 63 30,941,440 32 GB 31,675,645,952 16,383 16 63 61,866,496 64 GB 63,351,160,832 16,383 16 63 123,732,736 *Display of total bytes varies from file systems. **Cylinders, heads or sectors are not applicable for these capacities. Only LBA addressing applies. 1.5 Performance Performance of the SAFD 255 is shown in Table 1-2. Table 1-2 Performance specification Capacity Performance Sustained Read (MB/s) Sustained Write (MB/s) 8GB 16GB 32GB 64GB 230 230 230 230 85 180 170 175 Note: Performance varies from flash configurations. 4 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT 1.6 Pin Assignments Figure 1-2 illustrates the SAFD 255 signal pins, and Table1-3 describes its power pins. Figure 1-2 Pin Assignments Table 1-3: Signal segment Name Type S1 GND S2 RxP S3 RxN S4 GND S5 TxN S6 TxP S7 GND Table 1-4: Power segment Description Serial Data Receiver Serial Data Transmitter Pin Signal/Description P1 Not used (3.3V) P2 Not used (3.3V) P3 Not used (3.3V) P4 Ground P5 Ground P6 Ground P7 5V Pre-Charge P8 5V P9 5V P10 Ground P11 Ground P12 Ground P13 Not used (12V Pre-Charge) P14 Not used (12V) P15 Not used (12V) 5 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT Figure 1-3 SATA Cable/Connector Connection Diagram The connector on the left represents the Host with TX/RX differential pairs connected to a cable. The connector on the right shows the Device with TX/RX differential pairs also connected to the cable. Notice also the ground path connecting the shielding of the cable to the Cable Receptacle. 6 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT 2. Software Interface 2.1 Command Set Table 2-1 summarizes the ATA commands supported by the SAFD 255. Table 2-1: Command set Code Command Code Command E5h Check Power Mode F3h Security Erase Prepare 06h Data Set Management F4h Security Erase Unit 90h Execute Device Diagnostic F5h Security Freeze Lock E7h Flush Cache F1h Security Set Password EAh Flush Cache EXT F2h Security Unlock ECh Identify Device 70h Seek E3h Idle EFh Set Features E1h Idle Immediate C6h Set Multiple Mode 91h Initialize Device Parameters E6h Sleep C8h Read DMA B0h SMART 25h Read DMA EXT E2h Standby C4h Read Multiple E0h Standby Immediate 29h Read Multiple EXT CAh Write DMA 20h Read Sector 35h Write DMA EXT 24h Read Sector EXT C5h Write Multiple 40h Read Verify Sectors 39h Write Multiple EXT 42h Read Verify Sectors EXT 30h Write Sector 10h Recalibrate 34h Write Sector EXT F6h Security Disable Password 7 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT 3. Flash Management 3.1 Error Correction/Detection The SAFD 255 implements a hardware ECC scheme, based on the BCH algorithm. It can detect and correct up to 14 bits or 28 bits error in 1K bytes. 3.2 Bad Block Management Although bad blocks on the flash media are already identified by the flash manufacturer, they can also be accumulated over time during operation. The SAFD 255’s controller maintains a table that lists those normal blocks with disk data, the free blocks for wear leveling, and bad blocks with errors. When a normal block is detected broken, it is replaced with a free block and listed as a bad block. When a free block is detected broken, it is then removed from the free block list and marked as a bad block. During device operation, this ensures that newly accumulated bad blocks are transparent to the host. The device will stop file write service once there are only two free blocks left such that the read function is still available for copying the files from the disk into another. 3.3 Wear Leveling The NAND flash devices are limited by a certain number of write cycles. When using a FAT-based file system, frequent FAT table updates are required. If some area on the flash wears out faster than others, it would significantly reduce the lifetime of the whole SSD, even if the erase counts of others are far from the write cycle limit. Thus, if the write cycles can be distributed evenly across the media, the lifetime of the media can be prolonged significantly. This scheme is called wear leveling. Apacer’s wear-leveling scheme is achieved both via buffer management and Apacer-specific static wear leveling. They both ensure that the lifetime of the flash media can be increased, and the disk access performance is optimized as well. 3.4 Power Failure Management The Low Power Detection on the controller initiates crucial data saving before the power supplied to the device is too low. This feature prevents the device from crash and ensures data integrity during an unexpected power-off. 3.5 ATA Secure Erase Accomplished by the Secure Erase (SE) command, which added to the open ANSI standards that control disk drives, “ATA Secure Erase” is built into the disk drive itself and thus far less susceptible to malicious software attacks than external software utilities. It is a positive easy-to-use data destroy command, amounting to electronic data shredding. Executing the command causes a drive to internally completely erase all possible user data. This command is carried out within disk drives, so no additional software is required. Once executed, neither data nor the erase counter on the device would be recoverable, which blurs the accuracy of device lifespan. The process to erase will not be stopped until finished while encountering power failure, and will be continued when power is back on. 8 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT 3.6 S.M.A.R.T. S.M.A.R.T. is an acronym for Self-Monitoring, Analysis and Reporting Technology, an open standard allowing disk drives to automatically monitor their own health and report potential problems. It protects the user from unscheduled downtime by monitoring and storing critical drive performance and calibration parameters. Ideally, this should allow taking proactive actions to prevent impending drive failure. Apacer SAFD 255 uses the standard SMART command B0h to read data from the drive for SMART feature as the SATA Rev.2.6 ATA/ATAPI-7 specifications. Based on the SFF-8035i Rev. 2.0 specifications, Apacer SMART defines vendor-specified SMART Attribute IDs (A0h, A1h, A2h, A3h, A4h-A5h) in the SAFD 255. They represent initial bad block count, bad block count, spare block count, maximum erase count, and average erase counts respectively. When the Apacer SMART Utility running on the host, it analyzes and reports the disk status to the host before the SAFD 255 is in critical condition. 3.7 TRIM Made of millions of NAND flash cells, SSD can be written into groups called pages in 4K size generally, but can only be erased in larger groups called blocks of 128 pages or 512KB. These stipulations are partially the source of many performance issues. Until an address gets used again, the SSD has to keep track of every last bit of data that’s written on it. The ATA-TRIM instruction tilts the balance in favor of the SSD. TRIM addresses a major part of the performance degradation issue over time that plagues all SSDs. A TRIM enabled drive running an OS with TRIM support will stay closer to its peak performance over time. 9 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT 4. Environmental Specifications 4.1 Environments The SAFD 255 environmental specifications follow the US Military Standard MIL-STD-810F, as shown in Table 4-1. Table 4-1 SAFD 255 environmental specifications Environment Temperature Humidity Vibration Shock Specification 0°C to 70°C (Operating – Standard); -40°C to 85°C ( Operating – ET*) -40°C to 100°C (Non-operating) 5% to 95% RH (Non-condensing) Sine wave: 10~2000(Hz), 15(G) Random: 20~2000(Hz), 7.7(Grms) operating: 50(G), 11(ms) non-operating: 1500(G), 0.5(ms) *Extended Temperature 4.2 Mean Time Between Failures (MTBF) Mean Time Between Failures (MTBF) is predicted based on reliability data for the individual components in the SAFD 255. Although many component MTBFs are given in databases and often these values are not really accurate, the prediction result for the SAFD 255 is more than 2,000,000 hours. 4.3 Certification and Compliance The SAFD 255 complies with the following standards: CE – EN55022/55024 FCC 47CFR Part15 Class B RoHS MIL-STD-810F SATA II (SATA Rev. 2.6) Up to ATA/ATAPI-7 ( including S.M.A.R.T.) 10 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT 5. Electrical Characteristics 5.1 Operating Voltage Table 5-1 lists the supply voltage for SAFD 255. Table 5-1 SAFD 255 operating voltage Parameter Conditions Supply voltage 5.2 5.0 V ±10% ( 4.5-5.5 V) Power Consumption Table 5-2 lists the SAFD 255 power consumption. Table 5-2 SAFD 255 power consumption Capacity Performance Active Mode (mA) Idle Mode (mA) 8GB 16GB 32GB 64GB 357 486 532 535 95 90 87 94 11 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT 6. Physical Characteristics 6.1 Plastic Housing Figure 6-1 illustrates the overall dimensions of the SAFD 255 w/Plastic Housing, as listed in Table 6-1. Table 6-1 SAFD 255 w/Plastic Housing dimensions Millimeters (㎜ ㎜) Dimension Height 9.30 ± 0.10 Width 69.85 ± 0.10 Length 100.00 ± 0.10 LED 1 LED 1: Access (R/W) LED 2: Power LED 2 Figure 6-1 SAFD 255 w/Plastic Housing physical dimensions 12 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT 6.2 Metal Housing Figure 6-2 illustrates the overall dimensions of the SAFD 255 w/Metal Housing, as listed in Table 6-2. Table 6-2 SAFD 255 w/Metal Housing dimensions Millimeters (㎜ ㎜) Dimension Height 9.30 ± 0.20 Width 69.90 ± 0.15 Length 100.00 ± 0.15 Figure 6-2 SAFD 255 w/Metal Housing physical dimensions 13 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT 7. Product Ordering Information 7.1 Product Code Designations A P – SAFD 255 A X xxxx S – xx T Flash type Temperature Range Blank: Standard ET: Extended Temperature Environmental Specification Capacities: 008G = 016G = 032G = 064G = 8GB 16GB 32GB 64GB Housing Type A: Plastic Housing B: Metal Housing Solution version 2.5 inch Form Factor Serial ATA Flash Drive Apacer Product Code 14 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT 7.2 Valid Combinations A. Plastic Housing Capacity Standard Extended Temperature 8GB 16GB 32GB 64GB AP-SAFD255AA008GS-T AP-SAFD255AA016GS-T AP-SAFD255AA032GS-T AP-SAFD255AA064GS-T AP-SAFD255AA008GS-ETT AP-SAFD255AA016GS-ETT AP-SAFD255AA032GS-ETT AP-SAFD255AA064GS-ETT Capacity Standard Extended Temperature 8GB AP-SAFD255AB008GS-T AP-SAFD255AB008GS-ETT 16GB 32GB 64GB AP-SAFD255AB016GS-T AP-SAFD255AB032GS-T AP-SAFD255AB064GS-T AP-SAFD255AB016GS-ETT AP-SAFD255AB032GS-ETT AP-SAFD255AB064GS-ETT B. Metal Housing Note: Valid combinations are those products in mass production or will be in mass production. Consult your Apacer sales representative to confirm availability of valid combinations and to determine availability of new combinations. 15 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT Revision History Revision Description Date 0.1 Preliminary release 07/09/2010 0.2 Updated command set, trim information, and global presence 08/17/2010 1.0 Formal release 02/23/2011 1.1 Updated Performance Specifications & Power Consumption 04/01/2011 1.2 Updated Environmental Specifications 04/14/2011 16 © 2011 Apacer Technology Inc. Rev. 1.2 Serial ATA Flash Drive AP-SAFD255AXxxxxS-XXT Global Presence Taiwan (Headquarters) Apacer Technology Inc. th th 4 Fl., 75 Xintai 5 Rd., Sec.1 Hsichih, New Taipei City Taiwan 221 R.O.C. Tel: +886-2-2698-2888 Fax: +886-2-2698-2889 [email protected] U.S.A. Apacer Memory America, Inc. 386 Fairview Way, Suite102, Milpitas, CA 95035 Tel: 1-408-518-8699 Fax: 1-408-935-9611 [email protected] Japan Apacer Technology Corp. 5F, Matsura Bldg., Shiba, Minato-Ku Tokyo, 105-0014, Japan Tel: 81-3-5419-2668 Fax: 81-3-5419-0018 [email protected] Europe Apacer Technology B.V. Aziëlaan 22, 5232 BA 's-Hertogenbosch, The Netherlands Tel: 31-73-645-9620 Fax: 31-73-645-9629 [email protected] China Apacer Electronic (Shanghai) Co., Ltd 1301, No.251,Xiaomuqiao Road, Shanghai, 200032, China Tel: 86-21-5529-0222 Fax: 86-21-5206-6939 [email protected] India Apacer Technologies Pvt Ltd, #1064, 1st Floor, 7th ‘A’ Main, 3rd Block Koramangala, Bangalore – 560 034 Tel: +91 80 4152 9061/62/63 Fax: +91 80 4170 0215 [email protected] 17 © 2011 Apacer Technology Inc. Rev. 1.2 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Apacer: AP-SAFD255AA008GS-T AP-SAFD255AA016GS-T AP-SAFD255AA032GS-T AP-SAFD255AA064GS-T APSAFD255AA008GSETT AP-SAFD255AA016GSETT AP-SAFD255AA032GSETT AP-SAFD255AA064GSETT