Variable Resolution, 10-Bit to 16-Bit R/D Converter with Reference Oscillator AD2S1210 FEATURES DC and ac servo motor control Encoder emulation Electric power steering Electric vehicles Integrated starter generators/alternators Automotive motion sensing and control REFERENCE OSCILLATOR (DAC) EXCITATION OUTPUTS REFERENCE PINS CRYSTAL VOLTAGE REFERENCE INTERNAL CLOCK GENERATOR SYNTHETIC REFERENCE AD2S1210 ADC INPUTS FROM RESOLVER TYPE II TRACKING LOOP FAULT DETECTION OUTPUTS ADC POSITION REGISTER ENCODER EMULATION OUTPUTS VELOCITY REGISTER CONFIGURATION REGISTER DATA I/O MULTIPLEXER DATA BUS OUTPUT DATA I/O RESET Figure 1. GENERAL DESCRIPTION PRODUCT HIGHLIGHTS The AD2S1210 is a complete 10-bit to 16-bit resolution tracking resolver-to-digital converter, integrating an on-board programmable sinusoidal oscillator that provides sine wave excitation for resolvers. 1. The converter accepts 3.15 V p-p ± 27% input signals, in the range of 2 kHz to 20 kHz on the sine and cosine inputs. A Type II servo loop is employed to track the inputs and convert the input sine and cosine information into a digital representation of the input angle and velocity. The maximum tracking rate is 3125 rps. FAULT DETECTION 07467-001 APPLICATIONS FUNCTIONAL BLOCK DIAGRAM ENCODER EMULATION Complete monolithic resolver-to-digital converter 3125 rps maximum tracking rate (10-bit resolution) ±2.5 arc minutes of accuracy 10-/12-/14-/16-bit resolution, set by user Parallel and serial 10-bit to 16-bit data ports Absolute position and velocity outputs System fault detection Programmable fault detection thresholds Differential inputs Incremental encoder emulation Programmable sinusoidal oscillator on-board Compatible with DSP and SPI interface standards 5 V supply with 2.3 V to 5 V logic interface −40°C to +125°C temperature rating 2. 3. 4. 5. 6. Ratiometric tracking conversion. The Type II tracking loop provides continuous output position data without conversion delay. It also provides noise immunity and tolerance of harmonic distortion on the reference and input signals. System fault detection. A fault detection circuit can sense loss of resolver signals, out-of-range input signals, input signal mismatch, or loss of position tracking. The fault detection threshold levels can be individually programmed by the user for optimization within a particular application. Input signal range. The sine and cosine inputs can accept differential input voltages of 3.15 V p-p ± 27%. Programmable excitation frequency. Excitation frequency is easily programmable to a number of standard frequencies between 2 kHz and 20 kHz. Triple format position data. Absolute 10-bit to 16-bit angular position data is accessed via either a 16-bit parallel port or a 4-wire serial interface. Incremental encoder emulation is in standard A-quad-B format with direction output available. Digital velocity output. 10-bit to 16-bit signed digital velocity accessed via either a 16-bit parallel port or a 4-wire serial interface. Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2008–2010 Analog Devices, Inc. All rights reserved. AD2S1210* PRODUCT PAGE QUICK LINKS Last Content Update: 02/23/2017 COMPARABLE PARTS REFERENCE DESIGNS View a parametric search of comparable parts. • CN0276 • CN0317 EVALUATION KITS • AD-FMCMOTCON2-EBZ Evaluation Board DESIGN RESOURCES • AD2S1210 Evaluation Kit • AD2S1210 Material Declaration • Evaluation board for evaluating FlexMC Motor Control Universal AC Kit • PCN-PDN Information DOCUMENTATION • Quality And Reliability • Symbols and Footprints Data Sheet DISCUSSIONS • AD2S1210-DSCC: Military Data Sheet View all AD2S1210 EngineerZone Discussions. • AD2S1210-EP: Enhanced Product Data Sheet • AD2S1210-KGD: Known Good Die Data Sheet SAMPLE AND BUY • AD2S1210: Variable Resolution, 10-Bit to 16-Bit R/D Converter with Reference Oscillator Data Sheet Visit the product page to see pricing options. User Guides TECHNICAL SUPPORT • UG-709: Evaluating the AD2S1210 10-Bit to16-Bit Resolver-to-Digital Converter Submit a technical question or find your regional support number. SOFTWARE AND SYSTEMS REQUIREMENTS DOCUMENT FEEDBACK • AD2S1210 IIO Resolver-to-Digital Converter Linux Driver Submit feedback for this data sheet. TOOLS AND SIMULATIONS • AD2S1210 IBIS Model This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified. AD2S1210 TABLE OF CONTENTS Features .............................................................................................. 1 LOS Threshold Register ............................................................ 21 Applications ....................................................................................... 1 DOS Overrange Threshold Register ........................................ 21 Functional Block Diagram .............................................................. 1 DOS Mismatch Threshold Register ......................................... 21 General Description ......................................................................... 1 DOS Reset Maximum and Minimum Threshold Registers . 22 Product Highlights ........................................................................... 1 LOT High Threshold Register .................................................. 22 Revision History ............................................................................... 2 LOT Low Threshold Register ................................................... 22 Specifications..................................................................................... 3 Excitation Frequency Register .................................................. 22 Timing Specifications .................................................................. 6 Control Register ......................................................................... 22 Absolute Maximum Ratings............................................................ 8 Software Reset Register ............................................................. 23 ESD Caution .................................................................................. 8 Fault Register .............................................................................. 23 Pin Configuration and Function Descriptions ............................. 9 Digital interface .............................................................................. 24 Typical Performance Characteristics ........................................... 11 SOE Input .................................................................................... 24 Resolver Format Signals................................................................. 15 SAMPLE Input............................................................................ 24 Theory of Operation ...................................................................... 16 Data Format ................................................................................ 24 Resolver to Digital Conversion ................................................. 16 Parallel Interface ......................................................................... 24 Fault Detection Circuit .............................................................. 16 Serial Interface ............................................................................ 28 On-Board Programmable Sinusoidal Oscillator .................... 18 Incremental Encoder Outputs .................................................. 31 Synthetic Reference Generation ............................................... 18 Supply Sequencing and Reset ................................................... 31 Configuration of AD2S1210 ......................................................... 20 Circuit Dynamics ........................................................................... 32 Modes of Operation ................................................................... 20 Loop Response Model ............................................................... 32 Register Map.................................................................................... 21 Sources of Error .......................................................................... 33 Position Register ......................................................................... 21 Outline Dimensions ....................................................................... 34 Velocity Register ......................................................................... 21 Ordering Guide .......................................................................... 34 REVISION HISTORY 2/10—Rev. 0 to Rev. A Changes to Typical Performance Characteristics Section ... 11, 12 Changes to Ordering Guide .......................................................... 34 8/08—Revision 0: Initial Version Rev. A | Page 2 of 36 AD2S1210 SPECIFICATIONS AVDD = DVDD = 5.0 V ± 5%, CLKIN = 8.192 MHz ± 25%, EXC, EXC frequency = 10 kHz to 20 kHz (10-bit); 6 kHz to 20 kHz (12-bit); 3 kHz to 12 kHz (14-bit); 2 kHz to 10 kHz (16-bit); TA = TMIN to TMAX; unless otherwise noted. 1 Table 1. Parameter SINE, COSINE INPUTS 2 Voltage Amplitude Input Bias Current Input Impedance Phase Lock Range Common-Mode Rejection ANGULAR ACCURACY 3 Angular Accuracy Min Typ Max Unit Conditions/Comments 2.3 3.15 4.0 V p-p 8.25 μA kΩ Degrees arc sec/V Sinusoidal waveforms, differential SIN to SINLO, COS to COSLO VIN = 4.0 V p-p, CLKIN = 8.192 MHz VIN = 4.0 V p-p, CLKIN = 8.192 MHz Sine/cosine vs. EXC output, Control Register D3 = 0 10 Hz to 1 MHz, Control Register D4 = 0 ±5 + 1 LSB ±10 + 1 LSB arc min arc min Bits B, D grades A, C grades No missing codes ±1 ±2 ±2 ±4 ±4 ±8 ±16 ±32 ±0.9 LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB B, D grades A, C grades B, D grades A, C grades B, D grades A, C grades B, D grades A, C grades ±2 ±4 ±2 ±4 ±4 ±8 ±16 ±32 LSB LSB LSB LSB LSB LSB LSB LSB Bits B, D grades, zero acceleration A, C grades, zero acceleration B, D grades, zero acceleration A, C grades, zero acceleration B, D grades, zero acceleration A, C grades, zero acceleration B, D grades, zero acceleration A, C grades, zero acceleration 6500 5300 2800 2200 1500 1200 350 275 Hz Hz Hz Hz Hz Hz Hz Hz 485 −44 +44 ±20 ±2.5 + 1 LSB ±5 + 1 LSB 10, 12, 14, 16 Resolution Linearity INL 10-bit 12-bit 14-bit 16-bit Linearity DNL Repeatability VELOCITY OUTPUT Velocity Accuracy 4 10-bit ±1 12-bit 14-bit 16-bit Resolution 5 DYNAMNIC PERFORMANCE Bandwidth 10-bit 12-bit 14-bit 16-bit 9, 11, 13, 15 2000 2900 900 1200 400 600 100 125 Rev. A | Page 3 of 36 CLKIN = 8.192 MHz CLKIN = 8.192 MHz CLKIN = 8.192 MHz CLKIN = 8.192 MHz AD2S1210 Parameter Tracking Rate 10-bit Min Typ 12-bit 14-bit 16-bit Acceleration Error 10-bit 12-bit 14-bit 16-bit Settling Time 10° Step Input 10-bit 12-bit 14-bit 16-bit Settling Time 179° Step Input 10-bit 12-bit 14-bit 16-bit EXC, EXC OUTPUTS Voltage Center Voltage Frequency EXC/EXC DC Mismatch EXC/EXC AC Mismatch THD VOLTAGE REFERENCE REFOUT Drift PSRR CLKIN, XTALOUT 6 VIL Voltage Input Low VIH Voltage Input High LOGIC INPUTS VIL Voltage Input Low VIH Voltage Input High IOZH High Level Three-State Leakage IOZL Low Level Three-State Leakage Unit Conditions/Comments 3125 2500 1250 1000 625 500 156.25 125 rps CLKIN = 10.24 MHz CLKIN = 8.192 MHz CLKIN = 10.24 MHz CLKIN = 8.192 MHz CLKIN = 10.24 MHz CLKIN = 8.192 MHz CLKIN = 10.24 MHz CLKIN = 8.192 MHz 30 30 30 30 rps rps rps arc min arc min arc min arc min At 50,000 rps2, CLKIN = 8.192 MHz At 10,000 rps2, CLKIN = 8.192 MHz At 2500 rps2, CLKIN = 8.192 MHz At 125 rps2, CLKIN = 8.192 MHz 0.6 2.2 6.5 27.5 0.9 3.1 9.0 40 ms ms ms ms To settle to within ±2 LSB , CLKIN = 8.192 MHz To settle to within ±2 LSB, CLKIN = 8.192 MHz To settle to within ±2 LSB , CLKIN = 8.192 MHz To settle to within ±2 LSB, CLKIN = 8.192 MHz 1.5 4.75 10.5 45 2.2 6.0 14.7 66 ms ms ms ms To settle to within ±2 LSB , CLKIN = 8.192 MHz To settle to within ±2 LSB, CLKIN = 8.192 MHz To settle to within ±2 LSB , CLKIN = 8.192 MHz To settle to within ±2 LSB, CLKIN = 8.192 MHz 3.2 3.6 4.0 V p-p Load ±100 μA, typical differential output (EXC to EXC) = 7.2 V p-p 2.40 2 2.47 2.53 20 30 100 V kHz mV mV dB −58 2.40 2.47 100 −60 First five harmonics 2.53 V ppm/°C dB 0.8 V V 0.8 0.7 V V V V μA VDRIVE = 2.7 V to 5.25 V VDRIVE = 2.3 V to 2.7 V VDRIVE = 2.7 V to 5.25 V VDRIVE = 2.3 V to 2.7 V μA RES0, RES1, RD, WR/FSYNC, A0, A1, and RESET pins 2.0 2.0 1.7 IIL Low Level Input Current (Non Pull-Up) IIL Low Level Input Current (Pull-Up) IIH High Level Input Current LOGIC OUTPUTS VOL Voltage Output Low VOH Voltage Output High Max 10 80 −10 ±IOUT = 100 μA μA 0.4 2.4 2.0 −10 10 Rev. A | Page 4 of 36 V V V μA μA VDRIVE = 2.3 V to 5.25 V VDRIVE = 2.7 V to 5.25 V VDRIVE = 2.3 V to 2.7 V AD2S1210 Parameter POWER REQUIREMENTS AVDD DVDD VDRIVE POWER SUPPLY IAVDD IDVDD IOVDD Min 4.75 4.75 2.3 Typ Max Unit 5.25 5.25 5.25 V V V 12 35 2 mA mA mA 1 Conditions/Comments Temperature ranges are as follows: A, B grades: –40°C to +85°C; C, D grades: –40°C to +125°C. The voltages, SIN, SINLO, COS, and COSLO, relative to AGND, must always be between 0.15 V and AVDD − 0.2 V. All specifications within the angular accuracy parameter are tested at constant velocity, that is, zero acceleration. 4 The velocity accuracy specification includes velocity offset and dynamic ripple. 5 For example when RES0 = 0 and RES1 = 1, the position output has a resolution of 12 bits. The velocity output has a resolution of 11 bits with the MSB indicating the direction of rotation. In this example, with a CLKIN frequency of 8.192 MHz the velocity LSB is 0.488 rps, that is, 1000 rps/(211). 6 The clock frequency of the AD2S1210 can be supplied with a crystal, an oscillator, or directly from a DSP/microprocessor digital output. When using a single-ended clock signal directly from the DSP/microprocessor, the XTALOUT pin should remain open circuit and the logic levels outlined under the logic inputs parameter in Table 1 apply. 2 3 Rev. A | Page 5 of 36 AD2S1210 TIMING SPECIFICATIONS AVDD = DVDD = 5.0 V ± 5%, TA = TMIN to TMAX, unless otherwise noted. 1 Table 2. Parameter fCLKIN Description Frequency of clock input tCK Clock period ( = 1/fCLKIN) t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 A0 and A1 setup time before RD/CS low Delay CS falling edge to WR/FSYNC rising edge Address/data setup time during a write cycle Address/data hold time during a write cycle Delay WR/FSYNC rising edge to CS rising edge Delay CS rising edge to CS falling edge Delay between writing address and writing data A0 and A1 hold time after WR/FSYNC rising edge Delay between successive write cycles Delay between rising edge of WR/FSYNC and falling edge of RD Delay CS falling edge to RD falling edge Enable delay RD low to data valid in configuration mode VDRIVE = 4.5 V to 5.25 V VDRIVE = 2.7 V to 3.6 V VDRIVE = 2.3 V to 2.7 V RD rising edge to CS rising edge Disable delay RD high to data high-Z Disable delay CS high to data high-Z Delay between rising edge of RD and falling edge of WR/FSYNC SAMPLE pulse width Delay from SAMPLE before RD/CS low Hold time RD before RD low Enable delay RD/CS low to data valid VDRIVE = 4.5 V to 5.25 V VDRIVE = 2.7 V to 3.6 V VDRIVE = 2.3 V to 2.7 V RD pulse width A0 and A1 set time to data valid when RD/CS low VDRIVE = 4.5 V to 5.25 V VDRIVE = 2.7 V to 3.6 V VDRIVE = 2.3 V to 2.7 V Delay WR/FSYNC falling edge to SCLK rising edge Delay WR/FSYNC falling edge to SDO release from high-Z VDRIVE = 4.5 V to 5.25 V VDRIVE = 2.7 V to 3.6 V VDRIVE = 2.3 V to 2.7 V Delay SCLK rising edge to DBx valid VDRIVE = 4.5 V to 5.25 V VDRIVE = 2.7 V to 3.6 V VDRIVE = 2.3 V to 2.7 V SCLK high time SCLK low time SDI setup time prior to SCLK falling edge SDI hold time after SCLK falling edge t13 t14A t14B t15 t16 t17 t18 t19 t20 t21 t22 t23 t24 t25 t26 t27 t28 Rev. A | Page 6 of 36 Limit at TMIN, TMAX 6.144 10.24 98 163 2 22 3 2 2 10 2 × tCK + 20 2 6 × tCK + 20 2 2 Unit MHz min MHz max ns min ns max ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min 37 25 30 2 16 16 2 2 × tCK + 20 6 × tCK + 20 2 ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min 17 21 33 6 ns min ns min ns min ns min 36 37 29 3 ns min ns min ns min ns min 16 26 29 ns min ns min ns min 24 18 32 0.4 × tSCLK 0.4 × tSCLK 3 2 ns min ns min ns min ns min ns min ns min ns min AD2S1210 Parameter t29 t30 t31 t32 t33 t34 fSCLK 1 2 Description Delay WR/FSYNC rising edge to SDO high-Z Delay from SAMPLE before WR/FSYNC falling edge Delay CS falling edge to WR/FSYNC falling edge in normal mode A0 and A1 setup time before WR/FSYNC falling edge A0 and A1 hold time after WR/FSYNC falling edge 2 In normal mode, A0 = 0, A1 = 0/1 In configuration mode, A0 = 1, A1 = 1 Delay WR/FSYNC rising edge to WR/FSYNC falling edge Frequency of SCLK input VDRIVE = 4.5 V to 5.25 V VDRIVE = 2.7 V to 3.6 V VDRIVE = 2.3 V to 2.7 V Limit at TMIN, TMAX 15 6 × tCK + 20 ns 2 2 Unit ns min ns min ns min ns min 24 × tCK + 5 ns 8 × tCK + 5 ns 10 ns min ns min ns min 20 25 15 MHz MHz MHz Temperature ranges are as follows: A, B grades: –40°C to +85°C; C, D grades: –40°C to +125°C. A0 and A1 should remain constant for the duration of the serial readback. This may require 24 clock periods to read back the 8-bit fault information in addition to the 16 bits of position/velocity data. If the fault information is not required, A0/A1 may be released following 16 clock cycles. Rev. A | Page 7 of 36 AD2S1210 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter AVDD to AGND, DGND DVDD to AGND, DGND VDRIVE to AGND, DGND AVDD to DVDD AGND to DGND Analog Input Voltage to AGND Digital Input Voltage to DGND Digital Output Voltage to DGND Analog Output Voltage Swing Input Current to Any Pin Except Supplies 1 Operating Temperature Range (Ambient) A, B Grades C, D Grades Storage Temperature Range θJA Thermal Impedance 2 θJA Thermal Impedance2 RoHS-Compliant Temperature, Soldering Reflow ESD 1 2 Rating −0.3 V to +7.0 V −0.3 V to +7.0 V −0.3 V to AVDD −0.3 V to +0.3 V −0.3 V to +0.3 V −0.3 V to AVDD + 0.3 V −0.3 V to VDRIVE + 0.3 V −0.3 V to VDRIVE + 0.3 V −0.3 V to AVDD + 0.3 V ±10 mA Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION −40°C to +85°C −40°C to +125°C −65°C to +150°C 54°C/W 15°C/W 260(−5/+0)oC 2 kV HBM Transient currents of up to 100 mA do not cause latch-up. JEDEC 2S2P standard board. Rev. A | Page 8 of 36 AD2S1210 A0 EXC EXC AGND SIN SINLO COSLO AVDD COS REFBYP REFOUT RES0 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 48 47 46 45 44 43 42 41 40 39 38 37 RES1 1 36 A1 PIN 1 CS 2 35 DOS 34 LOT RD 3 WR/FSYNC 4 33 RESET DGND 5 32 DIR AD2S1210 DVDD 6 31 NM TOP VIEW (Not to Scale) CLKIN 7 30 B XTALOUT 8 29 A SOE 9 28 DB0 SAMPLE 10 27 DB1 DB15/SDO 11 26 DB2 DB14/SDI 12 25 DB3 07467-002 DB4 DB5 DB6 DB7 DB8 DGND VDRIVE DB9 DB10 DB11 DB12 DB13/SCLK 13 14 15 16 17 18 19 20 21 22 23 24 Figure 2. Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 Mnemonic RES1 2 3 CS RD 4 WR/FSYNC 5, 19 DGND 6 DVDD 7 CLKIN 8 XTALOUT 9 SOE 10 SAMPLE 11 DB15/SDO 12 DB14/SDI Description Resolution Select 1. Logic input. RES1 in conjunction with RES0 allows the resolution of the AD2S1210 to be programmed. Refer to the Configuration of AD2S1210 section. Chip Select. Active low logic input. The device is enabled when CS is held low. Edge-Triggered Logic Input. When the SOE pin is high, this pin acts as a frame synchronization signal and output enable for the parallel data outputs, DB15 to DB0. The output buffer is enabled when CS and RD are held low. When the SOE pin is low, the RD pin should be held high. Edge-Triggered Logic Input. When the SOE pin is high, this pin acts as a frame synchronization signal and input enable for the parallel data inputs, DB7 to DB0. The input buffer is enabled when CS and WR/FSYNC are held low. When the SOE pin is low, the WR/FSYNC pin acts as a frame synchronization signal and enable for the serial data bus. Digital Ground. These pins are ground reference points for digital circuitry on the AD2S1210. Refer all digital input signals to this DGND voltage. Both of these pins can be connected to the AGND plane of a system. The DGND and AGND voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis. Digital Supply Voltage, 4.75 V to 5.25 V. This is the supply voltage for all digital circuitry on the AD2S1210. The AVDD and DVDD voltages ideally should be at the same potential and must not be more than 0.3 V apart, even on a transient basis. Clock Input. A crystal or oscillator can be used at the CLKIN and XTALOUT pins to supply the required clock frequency of the AD2S1210. Alternatively, a single-ended clock can be applied to the CLKIN pin. The input frequency of the AD2S1210 is specified from 6.144 MHz to 10.24 MHz. Crystal Output. When using a crystal or oscillator to supply the clock frequency to the AD2S1210, apply the crystal across the CLKIN and XTALOUT pins. When using a single-ended clock source, the XTALOUT pin should be considered a no connect pin. Serial Output Enable. Logic input. This pin enables either the parallel or serial interface. The serial interface is selected by holding the SOE pin low, and the parallel interface is selected by holding the SOE pin high. Sample Result. Logic input. Data is transferred from the position and velocity integrators to the position and velocity registers, after a high-to-low transition on the SAMPLE signal. The fault register is also updated after a high-to-low transition on the SAMPLE signal. Data Bit 15/Serial Data Output Bus. When the SOE pin is high, this pin acts as DB15, a three-state data output pin controlled by CS and RD. When the SOE pin is low, this pin acts as SDO, the serial data output bus controlled by CS and WR/FSYNC. The bits are clocked out on the rising edge of SCLK. Data Bit 14/Serial Data Input Bus. When the SOE pin is high, this pin acts as DB14, a three-state data output pin controlled by CS and RD. When the SOE pin is low, this pin acts as SDI, the serial data input bus controlled by CS and WR/FSYNC. The bits are clocked in on the falling edge of SCLK. Rev. A | Page 9 of 36 AD2S1210 Pin No. 13 Mnemonic DB13/SCLK 14 to 17 18 DB12 to DB9 VDRIVE 20 21 to 28 29 DB8 DB7 to DB0 30 B 31 NM 32 DIR 33 RESET 34 LOT 35 DOS 36 A1 37 A0 38 EXC 39 EXC 40 AGND 41 42 43 SIN SINLO AVDD 44 45 46 47 48 COSLO COS REFBYP REFOUT RES0 A Description Data Bit 13/Serial Clock. In parallel mode, this pin acts as DB13, a three-state data output pin controlled by CS and RD. In serial mode, this pin acts as the serial clock input. Data Bit 12 to Data Bit 9. Three-state data output pins controlled by CS and RD. Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the interface operates. Decouple this pin to DGND. The voltage range on this pin is 2.3 V to 5.25 V and may be different to the voltage range at AVDD and DVDD but should never exceed either by more than 0.3 V. Data Bit 8. Three-state data output pin controlled by CS and RD. Data Bit 7 to Data Bit 0. Three-state data input/output pins controlled by CS, RD, and WR/FSYNC. Incremental Encoder Emulation Output A. Logic output. This output is free running and is valid if the resolver format input signals applied to the converter are valid. Incremental Encoder Emulation Output B. Logic output. This output is free running and is valid if the resolver format input signals applied to the converter are valid. North Marker Incremental Encoder Emulation Output. Logic output. This output is free running and is valid if the resolver format input signals applied to the converter are valid. Direction. Logic output. This output is used in conjunction with the incremental encoder emulation outputs. The DIR output indicates the direction of the input rotation and is high for increasing angular rotation. Reset. Logic input. The AD2S1210 requires an external reset signal to hold the RESET input low until VDD is within the specified operating range of 4.75 V to 5.25 V. Loss of Tracking. Logic output. LOT is indicated by a logic low on the LOT pin and is not latched. Refer to the Loss of Position Tracking Detection section. Degradation of Signal. Logic output. Degradation of signal (DOS) is detected when either resolver input (sine or cosine) exceeds the specified DOS sine/cosine threshold or when an amplitude mismatch occurs between the sine and cosine input voltages. DOS is indicated by a logic low on the DOS pin. Refer to the Signal Degradation Detection section. Mode Select 1. Logic input. A1 in conjunction with A0 allows the mode of the AD2S1210 to be selected. Refer to the Configuration of AD2S1210 section. Mode Select 0. Logic input. A0 in conjunction with A1 allows the mode of the AD2S1210 to be selected. Refer to the Configuration of AD2S1210 section. Excitation Frequency. Analog output. An on-board oscillator provides the sinusoidal excitation signal (EXC) and its complement signal (EXC) to the resolver. The frequency of this reference signal is programmable via the excitation frequency register. Excitation Frequency Complement. Analog output. An on-board oscillator provides the sinusoidal excitation signal (EXC) and its complement signal (EXC) to the resolver. The frequency of this reference signal is programmable via the excitation frequency register. Analog Ground. This pin is the ground reference points for analog circuitry on the AD2S1210. Refer all analog input signals and any external reference signal to this AGND voltage. Connect the AGND pin to the AGND plane of a system. The AGND and DGND voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis. Positive Analog Input of Differential SIN/SINLO Pair. The input range is 2.3 V p-p to 4.0 V p-p. Negative Analog Input of Differential SIN/SINLO Pair. The input range is 2.3 V p-p to 4.0 V p-p. Analog Supply Voltage, 4.75 V to 5.25 V. This pin is the supply voltage for all analog circuitry on the AD2S1210. The AVDD and DVDD voltages ideally should be at the same potential and must not be more than 0.3 V apart, even on a transient basis. Negative Analog Input of Differential COS/COSLO Pair. The input range is 2.3 V p-p to 4.0 V p-p. Positive Analog Input of Differential COS/COSLO Pair. The input range is 2.3 V p-p to 4.0 V p-p. Reference Bypass. Connect reference decoupling capacitors at this pin. Typical recommended values are 10 μF and 0.01 μF. Voltage Reference Output. Resolution Select 0. Logic input. RES0 in conjunction with RES1 allows the resolution of the AD2S1210 to be programmed. Refer to the Configuration of AD2S1210 section. Rev. A | Page 10 of 36 AD2S1210 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25°C, AVDD = DVDD = VDRIVE = 5 V, SIN/SINLO = 3.15 V p-p, COS/COSLO = 3.15 V p-p, CLKIN = 8.192 MHz , unless otherwise noted. 5000 9000 4500 8000 4000 7000 HITS PER CODE HITS PER CODE 3500 6000 5000 4000 3000 2500 2000 1500 3000 1000 2000 CODE Figure 3. Typical 16-Bit Angular Accuracy Histogram Of Codes, 10,000 Samples 07467-006 8199 CODE 0 07467-003 8198 8197 8196 8195 8194 8193 8192 8191 8190 8189 8188 8186 8187 8185 8184 8183 8182 8181 1000 8178 8179 8180 8181 8182 8183 8184 8185 8186 8187 8188 8189 8190 8191 8192 8193 8194 8195 8196 8197 8198 8199 8200 8201 500 Figure 6. Typical 12-Bit Angular Accuracy Histogram of Codes, 10,000 Samples, Hysteresis Disabled 8000 12000 7000 10000 8000 HITS PER CODE HITS PER CODE 6000 5000 4000 3000 6000 4000 2000 CODE 0 07467-004 8199 8198 8197 8196 8195 8194 8193 8192 8191 8190 8189 8188 8187 8186 8185 8184 8183 8182 8181 0 510 511 512 CODES 513 514 07467-017 2000 1000 Figure 7. Typical 12-Bit Angular Accuracy Histogram of Codes, 10,000 Samples, Hysteresis Enabled Figure 4. Typical 14-Bit Angular Accuracy Histogram of Codes, 10,000 Samples, Hysteresis Disabled 1400 12000 1200 10000 HITS PER CODE 6000 800 600 4000 400 2000 200 2047 2048 CODES 2049 2050 CODE Figure 5. Typical 14-Bit Angular Accuracy Histogram of Codes, 10,000 Samples, Hysteresis Enabled Figure 8. Typical 10-Bit Angular Accuracy Histogram of Codes, 10,000 Samples, Hysteresis Disabled Rev. A | Page 11 of 36 07467-018 2046 8176 8177 8178 8179 8180 8181 8182 8183 8184 8185 8186 8187 8188 8189 8190 8191 8192 8193 8194 8195 8196 8197 8198 8199 8200 0 0 07467-005 HITS PER CODE 1000 8000 AD2S1210 20 12000 18 16 14 8000 ANGLE (Degrees) HITS PER CODE 10000 6000 4000 12 10 8 6 4 2000 129 130 0 0 20 18 18 16 16 14 14 ANGLE (Degrees) 20 12 10 8 4 2 2 8 12 16 20 24 TIME (ms) 28 32 36 40 0 16 200 14 175 ANGLE (Degrees) 225 12 10 8 50 2 25 0 5 6 TIME (ms) 7 8 0.75 1.00 1.25 1.50 TIME (ms) 1.75 2.00 2.25 2.50 72 80 100 75 4 0.50 125 4 3 0.25 150 6 9 10 0 07467-009 ANGLE (Degrees) 250 18 2 5.00 Figure 13. Typical 10-Bit 10° Step Response 20 1 4.50 0 Figure 10. Typical 16-Bit 10° Step Response 0 4.00 8 6 4 3.50 10 4 0 1.50 2.00 2.50 3.00 TIME (ms) 12 6 0 1.00 Figure 12. Typical 12-Bit 10° Step Response 07467-010 ANGLE (Degrees) Figure 9. Typical 10-Bit Angular Accuracy Histogram of Codes, 10,000 Samples, Hysteresis Enabled 0.50 07467-007 128 CODES 0 Figure 11. Typical 14-Bit 10° Step Response 8 16 24 32 40 48 TIME (ms) 56 64 Figure 14. Typical 16-Bit 179° Step Response Rev. A | Page 12 of 36 07467-014 127 07467-038 126 07467-008 2 0 250 5 225 0 –5 175 –10 150 125 100 75 –25 –40 4 6 8 10 12 TIME (ms) 14 16 18 20 16-BIT –30 25 2 –45 1 0 225 –20 200 –40 175 –60 150 125 100 10k 100k 14-B IT –80 12-B IT –100 –120 16-B IT –140 75 –160 1 2 3 4 5 6 TIME (ms) 7 8 9 10 07467-012 –200 0 Figure 16. Typical 12-Bit 179° Step Response 1 10 100 1k F R E Q U E N C Y (H z) 10k 100k 07467-016 –180 25 Figure 19. Typical System Phase Response 10 225 9 200 8 TRACKING ERROR (Degrees) 250 175 150 125 100 75 50 25 7 6 5 4 3 2 0 1 2 3 4 TIME (ms) 5 0 Figure 17. Typical 10-Bit 179° Step Response 0 500 1000 1500 ACCELERATION (rps2) 2000 2500 Figure 20. Typical 16-Bit Tracking Error vs. Acceleration Rev. A | Page 13 of 36 07467-022 1 07467-011 ANGLE (Degrees) 100 1k FREQUENCY (Hz) 10-B IT PHASE (Degrees) ANGLE (Degrees) 250 50 0 10 Figure 18. Typical System Magnitude Response Figure 15. Typical 14-Bit 179° Step Response 0 12-BIT –20 –35 0 14-BIT –15 50 0 10-BIT 07467-015 MAGNITUDE (dB) 200 07467-013 ANGLE (Degrees) AD2S1210 10 10 9 9 8 8 TRACKING ERROR (Degrees) 7 6 5 4 3 2 0 6 5 4 3 2 1 0 5000 10000 15000 20000 25000 30000 35000 40000 45000 ACCELERATION (rps2) 07467-021 1 7 0 Figure 21. Typical 14-Bit Tracking Error vs. Acceleration 8 7 6 5 4 3 2 1 20000 60000 100000 ACCELERATION (rps2) 140000 180000 07467-020 TRACKING ERROR (Degrees) 9 0 200000 400000 600000 800000 ACCELERATION (rps2) 1000000 Figure 23. Typical 10-Bit Tracking Error vs. Acceleration 10 0 0 07467-019 TRACKING ERROR (Degrees) AD2S1210 Figure 22. Typical 12-Bit Tracking Error vs. Acceleration Rev. A | Page 14 of 36 AD2S1210 RESOLVER FORMAT SIGNALS Vr = Vp × sin(ωt) Vr = Vp × sin(ωt) R1 S2 S2 Va = Vs × sin(ωt) × cos(θ) θ R1 Va = Vs × sin(ωt) × cos(θ) θ S4 S4 R2 R2 S3 S1 Vb = Vs × sin(ωt) × sin(θ) S3 Vb = Vs × sin(ωt) × sin(θ) (A) CLASSICAL RESOLVER 07467-023 S1 (B) VARIABLE RELUCTANCE RESOLVER Figure 24. Classical Resolver vs. Variable Reluctance Resolver A resolver is a rotating transformer, typically with a primary winding on the rotor and two secondary windings on the stator. In the case of a variable reluctance resolver, there are no windings on the rotor, as shown in Figure 24. The primary winding is on the stator as well as the secondary windings, but the saliency in the rotor design provides the sinusoidal variation in the secondary coupling with the angular position. Either way, the resolver output voltages (S3 − S1, S2 − S4) have the same equations, as shown in Equation 1. S2 − S 4 = E 0 sin ωt × cos θ where: θ is the shaft angle. Sinωt is the rotor excitation frequency. E0 is the rotor excitation amplitude. (1) S2 – S4 (cos) S3 – S1 (sin) R2 – R4 (REF) 0° 90° 180° 270° θ Figure 25. Electrical Resolver Representation Rev. A | Page 15 of 36 360° 07467-024 S3 − S1 = E 0 sin ωt × sin θ The stator windings are displaced mechanically by 90° (see Figure 24). The primary winding is excited with an ac reference. The amplitude of subsequent coupling onto the stator secondary windings is a function of the position of the rotor (shaft) relative to the stator. The resolver, therefore, produces two output voltages (S3 − S1, S2 − S4) modulated by the sine and cosine of shaft angle. Resolver format signals refer to the signals derived from the output of a resolver, as shown in Equation 1. Figure 25 illustrates the output format. AD2S1210 THEORY OF OPERATION Monitor = A1 × sin θ × sin φ + A2 × cos θ × cos φ RESOLVER TO DIGITAL CONVERSION The AD2S1210 operates on a Type II tracking closed-loop principle. The output continually tracks the position of the resolver without the need for external conversion and wait states. As the resolver moves through a position equivalent to the least significant bit weighting, the output is updated by one LSB. (4) where: A1 is the amplitude of the incoming sine signal (A1 × sinθ). A2 is the amplitude of the incoming cosine signal (A2 × cosθ). θ is the resolver angle. ϕ is the angle stored in the position register. The converter tracks the shaft angle θ by producing an output angle ϕ that is fed back and compared to the input angle θ, and the resulting error between the two is driven towards 0 when the converter is correctly tracking the input angle. To measure the error, S3 − S1 is multiplied by cosϕ and S2 − S4 is multiplied by sinϕ to give E 0 sin ωt × sin θ cos φ (for S3 − S1) E 0 sin ωt × cos θ sin φ (for S2 − S4) The difference is taken, giving Note that Equation 4 is shown after demodulation, with the Carrier Signal sinωt removed. Also, note that for matched input signal (that is, a no fault condition), A1 = A2. When A1 = A2 and the converter is tracking (θ = ϕ), the monitor signal output has a constant magnitude of A1 (Monitor = A1 × (sin2 θ + cos2 θ) = A1), which is independent of shaft angle. When A1 ≠ A2, the monitor signal magnitude varies between A1 and A2 at twice the rate of shaft rotation. The monitor signal is used as described in the following sections to detect degradation or loss of input signals. Loss of Signal Detection E 0 sin ωt × (sin θ cos φ − cos θ sin φ ) (2) This signal is demodulated using the internally generated synthetic reference, yielding The AD2S1210 indicates that a loss of signal (LOS) has occurred for four separate conditions. • E 0 (sin θ cos φ − cos θ sin φ ) (3) Equation 3 is equivalent to E0sin(θ − ϕ), which is approximately equal to E0(θ − ϕ) for small values of θ − ϕ, where θ − ϕ = angular error. The value E0 (θ − ϕ) is the difference between the angular error of the rotor and the digital angle output of the converter. A phase-sensitive demodulator, some integrators, and a compensation filter form a closed-loop system that seeks to null the error signal. When this is accomplished, ϕ equals the Resolver Angle θ within the rated accuracy of the converter. A Type II tracking loop is used so that constant velocity inputs can be tracked without inherent error. FAULT DETECTION CIRCUIT The AD2S1210 fault detection circuit can sense loss of resolver signals, out-of-range input signals, input signal mismatch, or loss of position tracking; however, in the event of a fault, the position indicated by the AD2S1210 may differ significantly from the actual shaft position of the resolver. Monitor Signal The AD2S1210 generates a monitor signal by comparing the angle in the position register to the incoming sine and cosine signals from the resolver. The monitor signal is created in a similar fashion to the error signal described in the Resolver to Digital Conversion section. The incoming signals, sinθ and cosθ, are multiplied by the sin and cos of the output angle, respectively, and then added together. • • • When either resolver input (sine or cosine) falls below the specified LOS sine/cosine threshold. This threshold is defined by the user and is set by writing to the internal register, Address 0x88 (see the Register Map section). When any of the resolver input pins (SIN, SINLO, COS, or COSLO) are disconnected from the sensor. When any of the resolver input pins (SIN, SINLO, COS, or COSLO) are clipping the power rail or ground rail of the AD2S1210. Refer to the Sine/Cosine Input Clipping section. When a configuration parity error has occurred. Refer to the Configuration Parity Error section. A loss of signal is caused if either of the stator windings of the resolver (sine or cosine) are open circuit or have a number of shorted turns. LOS is indicated by both the DOS and LOT pins latching as logic low outputs. The DOS and LOT pins are reset to a no fault state when the user enters configuration mode and reads the fault register. The LOS condition has priority over both the DOS and LOT conditions, as shown in Table 6. To determine the cause of the LOS fault detection, the user must read the fault register, Address 0xFF (see the Register Map section). When a loss of signal is detected due to the resolver inputs (sine or cosine) falling below the specified LOS sine/cosine threshold, the electrical angle through which the resolver may rotate before the LOS can be detected by the AD2S1210 is referred to as the LOS angular latency. This is defined by the specified LOS sine/ cosine threshold set by the user and the maximum amplitude of the input signals being applied to the AD2S1210. The worst-case angular latency can be calculated as follows: Rev. A | Page 16 of 36 AD2S1210 Angular Latency = ⎡ ⎤ LOS threshold 2 × Arc cos ⎢ ⎥ ⎢⎣ max sine / cosine amplitude ⎥⎦ window counter periods for the range of excitation frequencies on the AD2S1210 are outlined in Table 5. (5) The preceding equation is based on the worst-case angular error, which can be seen by the AD2S1210 before an LOS fault is indicated. This occurs if one of the resolver input signals, either sine or cosine, is lost while the remaining signal is at its peak amplitude, for example, if the sine input is lost while the input angle is 90°. The worst-case angular latency is twice the worst-case angular error. The AD2S1210 indicates that a degradation of signal (DOS) has occurred for two separate conditions. • Excitation Frequency Range 2 kHz ≤ Exc Freq < 4 kHz 4 kHz ≤ Exc Freq < 8 kHz 8 kHz ≤ Exc Freq ≤ 20 kHz 1 Signal Degradation Detection • Table 5. Window Counter Period vs. Excitation Frequency Range, CLKIN = 8.192 MHz When either resolver input (sine or cosine) exceeds the specified DOS sine/cosine threshold. This threshold is defined by the user and is set by writing to the internal register, Address 0x89 (see the Register Map section). When the amplitudes of the input signals, sine and cosine, mismatch by more than the specified DOS sine/cosine mismatch threshold. This threshold is defined by the user and is set by writing to the internal register, Address 0x8A (see the Register Map section). The AD2S1210 continuously stores the minimum and maximum magnitude of the monitor signal in internal registers. The difference between the minimum and maximum is calculated to determine if a DOS mismatch has occurred. The initial values for the minimum and maximum internal registers must be defined by the user, at Address 0x8C and Address 0x8B, respectively (see the Register Map section). DOS is indicated by a logic low on the DOS pin. When DOS is indicated, the output is latched low until the user enters configuration mode and reads the fault register. The DOS condition has priority over the LOT condition, as shown in Table 6. To determine the cause of the DOS fault detection, the user must read the fault register, Address 0xFF (see the Register Map section). Time Latency for LOS and DOS Detection Note that the monitor signal is generated on the active edge of the internal AD2S1210 clock. The internal clock is generated by dividing the externally applied CLKIN frequency by 2; for example, when using a CLKIN frequency of 8.192 MHz the internal AD2S1210 clock is 4.096 MHz. The AD2S1210 continuously stores the minimum and maximum magnitude of the monitor signal in internal registers. The values stored in these internal registers are compared to the LOS and DOS thresholds configured by the user at set intervals. This interval, known as the window counter period, is dependent on the excitation frequency configured by the user. It is set to ensure that two window counter periods include at least one full period of the excitation frequency applied to the resolver. The window counter period is defined in terms of internal clock cycles. The Number of Internal Clock Cycles 1065 554 256 Window Counter Period (μs)1 260 135.25 62.5 CLKIN = 8.192 MHz. The window counter period scales with clock frequency and can be calculated by multiplying the number of internal clock cycles by the period of the internal clock frequency, that is, CLKIN/2. The AD2S1210 detects an LOS or DOS due to the resolver inputs (sine or cosine) falling below or exceeding the LOS and DOS thresholds within two window counter periods. For example, with an excitation frequency of 10 kHz, a fault is detected within 125 μs. A persistent fault is detected within one window counter period of the reading and clearing the fault register. Note that the time latency to detect the occurrence of a DOS mismatch fault is dependent on the speed of rotation of the resolver. The worst-case time latency to detect a DOS mismatch fault is the time required for one full rotation of the resolver. Loss of Position Tracking Detection The AD2S1210 indicates that a loss of tracking (LOT) has occurred when • • The internal error signal of the AD2S1210 has exceeded the specified angular threshold. This threshold is defined by the user and is set by writing to the internal register, Address 0x8D (see the Register Map section). The input signal exceeds the maximum tracking rate. The maximum tracking rate depends on the resolution defined by the user and the CLKIN frequency. LOT is indicated by a logic low on the LOT pin and is not latched. LOT has hysteresis and is not cleared until the internal error signal is less than the value defined in the LOT low threshold register, Address 0x8E (see the Register Map section). When the maximum tracking rate is exceeded, LOT is cleared only if the velocity is less than the maximum tracking rate and the internal error signal is less than the value defined in the LOT low threshold register. LOT can be indicated for step changes in position (such as after a RESET signal is applied to the AD2S1210). It is also useful as a built-in test to indicate that the tracking converter is functioning properly. The LOT condition has lower priority than both the DOS and LOS conditions, as shown in Table 6. The LOT and DOS conditions cannot be indicated using the LOT and DOS pins at the same time. However, both conditions are indicated separately in the fault register. To determine the cause of the LOT fault detection, the user must read the fault register, Address 0xFF (see the Register Map section). Rev. A | Page 17 of 36 AD2S1210 Table 6. Fault Detection Decoding Condition Loss of Signal (LOS) Degradation of Signal (DOS) Loss of Tracking (LOT) No Fault DOS Pin 0 0 1 1 LOT Pin 0 1 0 1 Order of Priority 1 2 3 N/A The AD2S1210 also provides an internal synthetic reference signal that is phase locked to its sine and cosine inputs. Phase errors between the resolver primary and secondary windings can degrade the accuracy of the RDC and are compensated by this synchronous reference signal. This also compensates the phase shifts due to temperature and cabling and eliminates the need of an external preset phase compensation circuit. Sine/Cosine Input Clipping SYNTHETIC REFERENCE GENERATION The AD2S1210 indicates that a clipping error has occurred if any of the resolver input pins (SIN, SINLO, COS, or COSLO) are clipping the power rail or ground rail of the AD2S1210. The clipping fault is indicated if the input amplitudes are less than 0.15 V or greater then AVDD − 0.2 V for more than 4 μs. When a resolver undergoes a high rotation rate, the RDC tends to act as an electric motor and produces speed voltages, along with the ideal sine and cosine outputs. These speed voltages are in quadrature to the main signal waveform. Moreover, nonzero resistance in the resolver windings causes a nonzero phase shift between the reference input and the sine and cosine outputs. The combination of speed voltages and phase shift causes a tracking error in the RDC that is approximated by Sine/cosine input clipping error is indicated by both the DOS and LOT pins latching as logic low outputs. Sine/cosine input clipping error is also indicated by Bit D7 of the fault register being set high. The DOS and LOT pins are reset to a no fault state when the user enters configuration mode and reads the fault register. Configuration Parity Error The AD2S1210 includes a number of user programmable registers that allow the user to configure the part. Each read/write register on the AD2S1210 is programmed with seven bits of information by the user. The 8th bit is reserved as a parity error bit. In the event that the data within these registers becomes corrupted, the AD2S1210 indicates that a configuration parity error has occurred. Configuration parity error is indicated by both the DOS and LOT pins latching as logic low outputs. Configuration parity error is also indicated by Bit D0 of the fault register being set high. In the event that a parity error occurs, it is recommended that the user reset the part using the RESET pin. Phase Lock Error The AD2S1210 indicates that a phase lock error has occurred if the difference between the phase of the excitation frequency and the phase of the sine and cosine signals exceeds the specified phase lock range. Phase lock error is indicated by a logic low on the LOT pin and is not latched. Phase lock error is also indicated by Bit D1 of the fault register being set high. ON-BOARD PROGRAMMABLE SINUSOIDAL OSCILLATOR An on-board oscillator provides the sinusoidal excitation signal (EXC) to the resolver as well as its complemented signal (EXC). The frequency of this reference signal is programmable to a number of standard frequencies between 2 kHz and 20 kHz. The amplitude of this signal is 3.6 V p-p and is centered on 2.5 V. Error = Phase Shift × Rotation Rate Reference Frequency (6) To compensate for the described phase error between the resolver reference excitation and the sine/cosine signals, an internal synthetic reference signal is generated in phase with the reference frequency carrier. The synthetic reference is derived using the internally filtered sine and cosine signals. It is generated by determining the zero crossing of either the sine or cosine (whichever signal is larger, to improve phase accuracy) and evaluating the phase of the resolver reference excitation. The synthetic reference reduces the phase shift between the reference and sine/cosine inputs to less than 10°, and operates for phase shifts of ±44°. If additional phase lock range is required, Bit D5 in the control register can be set to zero to expand the phase lock range to 360° (see the Control Register section). CONNECTING THE CONVERTER Ground is connected to the AGND and DGND pins (see Figure 26). A positive power supply (VDD) of 5 V dc ± 5% is connected to the AVDD and DVDD pins, with typical values for the decoupling capacitors being 10 nF and 4.7 μF. These capacitors are then placed as close to the device pins as possible and are connected to both AVDD and DVDD. The VDRIVE pin is connected to the supply voltage of the microprocessor. The voltage applied to the VDRIVE input controls the voltage of the parallel and serial interfaces. VDRIVE can be set to 5 V, 3 V, or 2.5 V. Typical values for the VDRIVE decoupling capacitors are 10 nF and 4.7 μF. Typical values for the oscillator decoupling capacitors are 20 pF, whereas typical values for the reference decoupling capacitors are 10 nF and 10 μF. The reference excitation output of the AD2S1210 needs an external buffer amplifier to provide gain and the additional current to drive a resolver. Rev. A | Page 18 of 36 AD2S1210 S2 S4 5V S1 R1 BUFFER CIRCUIT 2 EXC EXC SIN AGND SINLO 1 35 4 6 DVDD 7 CLKIN 30 8 XTALOUT 29 AD2S1210 31 9 28 10 27 11 26 12 20pF 20pF R2 ⎞ ⎞ ⎛ R2 ⎞ ⎛ 1 ⎛ ⎞V (8) VOUT = ⎜ V REF × ⎛⎜1 + ⎟ IN ⎟⎟ − ⎜ ⎟×⎜ ⎝ R1 ⎠ ⎠ ⎝ R1 ⎠ ⎝ 1 + R2 × C1 × ω ⎠ ⎝ 32 where: ω is the radian frequency of the applied signal. VREF, a dc voltage, is set so that VOUT is always a positive value, eliminating the need for a negative supply. 25 C1 13 14 15 16 17 18 19 20 21 22 23 24 R2 VDRIVE 4.7µF 12V 07467-025 10nF EXC/EXC (VIN) Figure 26. Connecting the AD2S1210 to a Resolver In this recommended configuration, the converter introduces a VREF/2 offset in the SIN, SINLO, COS, and COSLO signal outputs from the resolver. The sine and cosine signals can each be connected to a different potential relative to ground if the sine and cosine signals adhere to the recommended specifications. Note that because the EXC and EXC outputs are differential, there is an inherent gain of 2×. 12V R1 (VREF ) AD8662 5V VOUT 07467-026 8.192 MHZ DGND DGND 5V (7) and 33 5 VDRIVE 4.7µF Carrier Gain = − (R2 / R1) × (1 /(1 + R2 × C1 × ω)) 36 34 3 10nF Figure 27 shows a suggested buffer circuit. Capacitor C1 may be used in parallel with Resistor R2 to filter out any noise that may exist on the EXC and EXC outputs. Care should be taken when selecting the cutoff frequency of this filter to ensure that phase shifts of the carrier caused by the filter do not exceed the phase lock range of the AD2S1210. The gain of the circuit is 48 47 46 45 44 43 42 41 40 39 38 37 COS 10µF COSLO AVDD 10nF S3 BUFFER CIRCUIT REFBYP 10nF REFOUT 4.7µF R2 Figure 27. Buffer Circuit A separate screened twisted pair cable is recommended for the analog input pins, SIN, SINLO, COS, and COSLO. The screens should terminate to either REFOUT or AGND. Rev. A | Page 19 of 36 AD2S1210 CONFIGURATION OF AD2S1210 MODES OF OPERATION The AD2S1210 has two modes of operation: configuration mode and normal mode. The configuration mode is used to program the registers that set the excitation frequency, the resolution, and the fault detection thresholds of the AD2S1210. Configuration mode is also used to read back the information in the fault register. The data in the position and velocity registers can also be read back while in configuration mode. The AD2S1210 can be operated entirely in configuration mode or, when the initial configuration is completed, the part can be taken out of configuration mode and operated in normal mode. When operating in normal mode, the data outputs can provide angular position or angular velocity data. The A0 and A1 inputs are used to determine whether the AD2S1210 is in configuration mode and to determine whether the position or velocity data is supplied to the output pins, see Table 8. Setting the Excitation Frequency The excitation frequency of the AD2S1210 is set by writing a frequency control word to the excitation frequency register, Address 0x91 (see the Register Map section). Excitation Frequency = (FCW × f CLKIN ) The specified range of the excitation frequency is from 2 kHz to 20 kHz and can be set in increments of 250 Hz. To achieve the angular accuracy specifications in Table 1, the excitation frequency should be selected as outlined in Table 7. Table 7. Recommended Excitation Frequency vs. Resolution (fCLKIN = 8.192 MHz) Typical Bandwidth 4100 Hz 1700 Hz 900 Hz 250 Hz Min Excitation Frequency 10 kHz 6 kHz 3 kHz 2 kHz A0, A1 Inputs The AD2S1210 allows the user to read the angular position or the angular velocity data directly from the parallel outputs or through the serial interface. The required information can be selected using the A0 and A1 inputs. These inputs should also be used to put the part into configuration mode. The data from the fault register and the remaining on-chip registers can be accessed in configuration mode. Table 8. Configuration Mode Settings A0 0 0 1 1 A1 0 1 0 1 Result Normal mode—position output Normal mode—velocity output Reserved Configuration mode RES0, RES1 Inputs 2 15 where FCW is the frequency control word and fCLKIN is the clock frequency of the AD2S1210. Resolution 10 Bits 12 Bits 14 Bits 16 Bits Note that the recommended frequency range for each resolution and bandwidth, as outlined in Table 7, are defined for a clock frequency of 8.192 MHz. The recommended excitation frequency range scales with the clock frequency of the AD2S1210. The default excitation frequency of the AD2S1210 is 10 kHz when operated with a clock frequency of 8.192 MHz. Max Excitation Frequency 20 kHz 20 kHz 12 kHz 10 kHz In normal mode, the resolution of the digital output is selected using the RES0 and RES1 input pins. In configuration mode, the resolution is selected by setting the RES0 and RES1 bits in the control register. When switching between normal mode and configuration mode, it is the responsibility of the user to ensure that the resolution set in the control register matches the resolution set by the RES0 and RES1 input pins. Failure to do so may result in incorrect data on the outputs, caused by the differences between the resolution settings. Table 9. Resolution Settings RES0 0 0 1 1 1 RES1 0 1 0 1 Resolution (Bits) 10 12 14 16 Position LSB (Arc min) 21.1 5.3 1.3 0.3 Velocity LSB (rps) 1 4.88 0.488 0.06 0.004 CLKIN = 8.192 MHz. The velocity LSB size and maximum tracking rate scale linearly with the CLKIN frequency. Rev. A | Page 20 of 36 AD2S1210 REGISTER MAP Table 10. Register Map Register Name Position Velocity LOS Threshold DOS Overrange Threshold DOS Mismatch Threshold DOS Reset Max Threshold DOS Reset Min Threshold LOT High Threshold LOT Low Threshold Excitation Frequency Control Soft Reset Fault Register Address 0x80 0x81 0x82 0x83 0x88 0x89 Register Data D15 to D8 D7 to D0 D15 to D8 D7 to D0 D7 to D0 D7 to D0 Read/Write Register Read only Read only Read only Read only Read/write Read/write 0x8A D7 to D0 Read/write 0x8B D7 to D0 Read/write 0x8C D7 to D0 Read/write 0x8D 0x8E 0x91 0x92 0xF0 0xFF D7 to D0 D7 to D0 D7 to D0 D7 to D0 D7 to D0 D7 to D0 Read/write Read/write Read/write Read/write Write only Read only Table 11. 16-Bit Register Bit D15 to D8 D7 to D0 The value stored in the velocity register is 16 bits regardless of resolution. At lower resolutions, the LSBs of the 16-bit digital output should be ignored. For example, at 10-bit resolution, Data Bit D15 to Data Bit D6 provide valid data; D5 to D0 should be ignored. The maximum tracking rate of the AD2S1210 at 10-bit resolution with an 8.192 MHz input clock is ±2500 rps. A velocity of +2500 rps results in 0x1FF being stored in Bit D15 to Bit D6 of the velocity register; a velocity of −2500 rps results in 0x3FF being stored in Bit D15 to Bit D6 of the velocity register. In this 10-bit example, the LSB size of the velocity output is 4.88 rps. LOS THRESHOLD REGISTER Table 13. 8-Bit Register Address 0x88 Bit D7 to D0 Read/Write Read/write The LOS threshold register determines the loss of signal threshold of the AD2S1210. The AD2S1210 allows the user to set the LOS threshold to a value between 0 V and 4.82 V. The resolution of the LOS threshold is seven bits, that is, 38 mV. Note that the MSB, D7, should be set to 0. The default value of the LOS threshold on power-up is 2.2 V. POSITION REGISTER Address 0x80 0x81 maximum velocity that the AD2S1210 can track for each resolution is specified in Table 1. For example, the maximum tracking rate of the AD2S1210 at 16 bits resolution, with an 8.192 MHz input clock, is ±125 rps. A velocity of +125 rps results in 0x7FFF being stored in the velocity register; a velocity of −125 rps results in 0x8000 being stored in the velocity register. Read/Write Read only Read only The position register contains a digital representation of the angular position of the resolver input signals. The values are stored in 16-bit binary format. The value in the position register is updated following a falling edge on the SAMPLE input. DOS OVERRANGE THRESHOLD REGISTER Table 14. 8-Bit Register Address 0x89 Bit D7 to D0 Read/Write Read/write Note that with hysteresis enabled (see the Control Register section), at lower resolutions, the LSBs of the 16-bit digital output are set to zero. For example, at 10-bit resolution, Data Bit D15 to Data Bit D6 provide valid data; D5 to D0 are set to zero. With hysteresis disabled, the value stored in the position register is 16 bits regardless of resolution. At lower resolutions, the LSBs of the 16-bit digital output can be ignored. For example, at 10-bit resolution, Data Bit D15 to Data Bit D6 provide valid data; D5 to D0 can be ignored. The DOS overrange threshold register determines the degradation of signal threshold of the AD2S1210. The AD2S1210 allows the user to set the DOS overrange threshold to a value between 0 V and 4.82 V. The resolution of the DOS overrange threshold is seven bits, that is, 38 mV. Note that the MSB, D7, should be set to 0. The default value of the DOS overrange threshold on power-up is 4.1 V. VELOCITY REGISTER Table 15. 8-Bit Register Table 12. 16-Bit Register Address 0x8A Address 0x82 0x83 Bit D15 to D8 D7 to D0 Read/Write Read only Read only The velocity register contains a digital representation of the angular velocity of the resolver input signals. The value in the velocity register is updated following a falling edge on the sample input. The values are stored in 16-bit, twos complement format. The DOS MISMATCH THRESHOLD REGISTER Bit D7 to D0 Read/Write Read/write The DOS mismatch threshold register determines the signal mismatch threshold of the AD2S1210. The AD2S1210 allows the user to set the DOS mismatch threshold to a value between 0 V and 4.82 V. The resolution of the DOS mismatch threshold is seven bits, that is, 38 mV. Note that the MSB, D7, should be set to 0.The default value of the DOS mismatch threshold on power-up is 380 mV. Rev. A | Page 21 of 36 AD2S1210 Table 19. LOT High/Low Threshold DOS RESET MAXIMUM AND MINIMUM THRESHOLD REGISTERS Table 16. 8-Bit Registers Address 0x8B 0x8C Bit D7 to D0 D7 to D0 Read/Write Read/write Read/write The AD2S1210 continuously stores the minimum and maximum magnitude of the monitor signal in internal registers. The difference between the minimum and maximum is calculated to determine if a DOS mismatch has occurred. The initial values for the minimum and maximum internal registers must be defined by the user. When the fault register is cleared, the registers that store the maximum and minimum amplitudes of the monitor signal are reset to the values stored in the DOS reset maximum and minimum threshold registers. The resolution of the DOS reset maximum and minimum thresholds is seven bits each, that is, 38 mV. Note that the MSB, D7, should be set to 0.To ensure correct operation, it is recommended that the DOS reset minimum threshold register be set to at least 1 LSB less than the DOS overrange threshold, and the DOS reset maximum threshold register be set to at least 1 LSB greater than the LOS threshold register. The default value of the DOS reset minimum threshold register and the DOS reset maximum threshold register are 3.99 V and 2.28 V, respectively. LOT HIGH THRESHOLD REGISTER Bit D7 to D0 Read/Write Read/write LOT High Default (Degrees) 12.5 5.0 2.5 2.5 EXCITATION FREQUENCY REGISTER Table 20. 8-Bit Register Address 0x91 Bit D7 to D0 Read/Write Read/write The excitation frequency register determines the frequency of the excitation outputs of the AD2S1210. A 7-bit frequency control word is written to the register to set the excitation frequency. Note that the MSB, D7, should be set to 0. (Excitation Frequency × 2 ) 15 FCW = f CLKIN (9) where FCW is the frequency control word and fCLKIN is the clock frequency of the AD2S1210. The specified range of the excitation frequency is from 2 kHz to 20 kHz and can be set in increments of 250 Hz. To ensure that the AD2S1210 is operated within the specified frequency range, the frequency control word should be a value between 0x4 and 0x50. FCW = (5 kHz × 2 ) Table 18. 8-Bit Register 8.192 MHz = 14 (hexadecimal) The default excitation frequency of the AD2S1210 on power-up is 10 kHz. CONTROL REGISTER Table 21. 8-Bit Register Address 0x92 LOT LOW THRESHOLD REGISTER Bit D7 to D0 LOT Low Default (Degrees) 2.5 1.0 0.5 0.5 LSB Size (Degrees) 0.35 0.14 0.09 0.09 15 The LOT high threshold register determines the loss of position tracking threshold for the AD2S1210. The LOT high threshold is a 7-bit word. Note that the MSB, D7, should be set to 0. The range of the LOT high threshold, the LSB size, and the default value of the LOT high threshold on power-up are dependent on the resolution setting of the AD2S1210, and are outlined in Table 19. Address 0x8E Range (Degrees) 0 to 45 0 to 18 0 to 9 0 to 9 For example, if the user requires an excitation frequency of 5 kHz and has an 8.192 MHz clock frequency, the code that needs to be programmed is given by Table 17. 8-Bit Register Address 0x8D Resolution (Bits) 10 12 14 16 Bit D7 to D0 Read/Write Read/write The control register is an 8-bit register that sets the AD2S1210 control modes. The default value of the control register on power-up is 0x7E. Read/Write Read/write The LOT low threshold register determines the level of hysteresis on the loss of position tracking fault detection. Loss of tracking (LOT) occurs when the internal error signal of the AD2S1210 exceeds the LOT high threshold. LOT has hysteresis and is not cleared until the internal error signal is less than the value defined in the LOT low threshold register. The LOT low threshold is a 7-bit word. Note that the MSB, D7, should be set to 0. The range of the LOT high threshold, the LSB size, and the default value of the LOT high threshold on power-up are dependent on the resolution setting of the AD2S1210, and are outlined in Table 19. Table 22. Control Register Bit Descriptions Bit D7 D6 D5 D4 D3 D2 D1 D0 Rev. A | Page 22 of 36 Description Address/data bit Reserved; set to 1 Phase lock range 0 = 360°, 1 = ±44° 0 = disable hysteresis, 1 = enable hysteresis Set Encoder Resolution EnRES1 Set Encoder Resolution EnRES0 Set Resolution RES1 Set Resolution RES0 AD2S1210 Address/Data Bit Table 23. Encoder Resolution Settings The MSB of each 8-bit word written to the AD2S1210 indicates whether the 8-bit word is a register address or data. The MSB (D7) of each register address defined on the AD2S1210 is high. The MSB of each data word written to the AD2S1210 is low. EnRES0 0 0 1 1 Note that when a data word is written to the AD2S1210, the MSB is internally reconfigured as a parity bit. When reading data from any of the read/write registers (see Table 10), the parity of Bit D6 to Bit D0 is recalculated and compared to the previously stored parity bit. The MSB of the 8-bit output is used to indicate whether a configuration error has occurred. If the MSB is returned high, this indicates that the data read back from the device does not match the configuration data written to the device in the previous write cycle. Phase Lock Range The phase lock range allows the AD2S1210 to compensate for phase errors between the excitation frequency and the sine/cosine inputs. The recommended mode of operation is to use the default phase lock range of ±44°. If additional phase lock range is required, a range of 360° can be set. However, in this mode of operation, the AD2S1210 should be reset following a loss of signal error. Failure to do so may result in a 180° error in the angular output data. Hysteresis The AD2S1210 includes a hysteresis function, ±1 LSB, between the output of the position integrator and the input to the position register. When operating in a noisy environment, this can be used to prevent flicker on the LSB. On the AD2S1210, the maximum tracking rate is defined by the bandwidth. Each resolution setting is internally configured with a different bandwidth, as outlined in Table 1. The maximum tracking rate and the bandwidth are inversely proportional to the resolution, that is, the maximum tracking rate increases as the resolution is decreased. The option of disabling the hysteresis allows the user to oversample the position output and to achieve a higher resolution output within the specified bandwidths through external averaging. The hysteresis function can be enabled or disabled through setting Bit D4 in the control register. Hysteresis is enabled by default on power-up. Set Encoder Resolution The resolution of the encoder outputs of the AD2S1210 can be set to the same resolution as the digital output or it can also be set to a lower resolution. For example, when the resolution of the AD2S1210 position outputs is set to 16 bits, the resolution of the encoder outputs may be set to 14, 12, or 10 bits. This allows the user to take advantage of the lower bandwidth and improved performance of the 16-bit resolution setting without requiring external divide down of the A-quad-B encoder outputs. The default resolution of the encoder outputs on power-up is 16 bits. Refer to the Incremental Encoder Outputs section. EnRES1 0 1 0 1 Resolution (Bits) 10 12 14 16 Set Resolution In normal mode, the resolution of the digital output is selected using the RES0 and RES1 input pins (see Table 9). In configuration mode, the resolution is selected by setting the RES0 and RES1 bits in the control register. When switching between normal mode and configuration mode, it is the responsibility of the user to ensure that the resolution set in the control register matches the resolution set by the RES0 and RES1 input pins. The default resolution of the digital output on power-up is 12 bits. SOFTWARE RESET REGISTER Table 24. 8-Bit Register Address 0xF0 Bit D7 to D0 Read/Write Write only Addressing the software reset register, that is writing the 8-bit address, 0xF0, of the software reset register to the AD2S1210 while in configuration mode, allows the user to initiate a software reset of the AD2S1210. The software reset reinitializes the excitation frequency outputs and the internal Type II tracking loop. The data stored in the configuration registers is not overwritten by a software reset. However, it should be noted that the data in the fault register is reset. In an application that uses two or more resolver-to-digital converters, which are both driven from the same clock source, the software reset can be used to synchronize the phase of the excitation frequencies across the converters. FAULT REGISTER Table 25. 8-Bit Register Address 0xFF Bit D7 to D0 Read/Write Read only The AD2S1210 has the ability to detect eight separate fault conditions. When a fault occurs, the DOS and/or the LOT output pins are taken low. By reading the fault register, the user can determine the cause of the triggering of the fault detection output pins. Note that the fault register bits are active high, that is, the fault bits are taken high to indicate that a fault has occurred. Table 26. Fault Register Bit Descriptions Bit D7 D6 D5 D4 D3 D2 D1 D0 Rev. A | Page 23 of 36 Description Sine/cosine inputs clipped Sine/cosine inputs below LOS threshold Sine/cosine inputs exceed DOS overrange threshold Sine/cosine inputs exceed DOS mismatch threshold Tracking error exceeds LOT threshold Velocity exceeds maximum tracking rate Phase error exceeds phase lock range Configuration parity error AD2S1210 DIGITAL INTERFACE The angular position and angular velocity are represented by binary data and can be extracted either via a 16-bit parallel interface or via a 4-wire serial interface that operates at clock rates of up to 25 MHz. The AD2S1210 programmable functions are controlled using a set of on-chip registers. Data is written to these registers using either the serial or the parallel interface. SOE INPUT The serial output enable pin, SOE, is held high to enable the parallel interface. The SOE pin is held low to enable the serial interface, which places Pin DB0 to Pin DB12 in the high impedance state. Pin DB13 is the serial clock input (SCLK), Pin DB14 is the serial data input (SDI), Pin DB15 is the serial data output (SDO), and WR/FSYNC is the frame synchronization input. SAMPLE INPUT The AD2S1210 operates on a Type II tracking closed-loop principle. The loop continually tracks the position and velocity of the resolver without the need for external conversion and wait states. The position and velocity registers are external to the loop and are updated with a high-to-low transition of the SAMPLE signal. This pin must be held low for at least t16 ns to guarantee correct latching of the data. DATA FORMAT The digital angle data represents the absolute position of the resolver shaft as a 10-bit to 16-bit unsigned binary word. The digital velocity data is a 10-bit to 16-bit twos complement word, which represents the velocity of the resolver shaft rotating in either a clockwise or a counterclockwise direction. Reading from the AD2S1210 The following data can be read back from the AD2S1210: • • • • Angular position Angular velocity Fault register data Status of on-chip registers The angular position and angular velocity data can be read back in either normal mode or configuration mode. To read the status of the fault register or the remaining on-chip registers, the part must be put into configuration mode. Reading from the AD2S1210 in Configuration Mode To read back data stored in one of the on-chip registers, including the fault register, the user must first place the AD2S1210 into configuration mode using the A0 and A1 inputs. The 8-bit address of the register to be read should then be written to the part, as described in the Writing to the AD2S1210 section. This transfers the relevant data to the output register. The data can then be read using the RD input as described previously. When reading back data from any of the read/write registers (see Table 10), the 8-bit word consists of the seven bits of data in the relevant register, D6 to D0, and an error bit, D7. If the error bit is returned high, this indicates that the data read back from the device does not match the configuration data written to the device in the previous write cycle. The parallel interface is selected holding the SOE pin high. The chip select pin, CS, must be held low to enable the interface. If the user wants to read back the angular position or velocity data while in configuration mode, a falling edge of the SAMPLE input is required to update the information in the position and velocity registers. The data in these registers can then be read back by addressing the required register and reading back the data as described previously. Figure 29 shows the timing specifications to follow when reading from the configuration registers. Writing to the AD2S1210 Reading from the AD2S1210 in Normal Mode The on-chip registers of the AD2S1210 are written to, in parallel mode, using an 8-bit parallel interface, D7 to D0, and the WR/ FSYNC pin. The MSB of each 8-bit word written to the AD2S1210 indicates whether the 8-bit word is a register address or data. The MSB (D7) of each register address defined on the AD2S1210 is high (see the Register Map section). The MSB of each data word written to the AD2S1210 is low. To write to one of the registers, the user must first place the AD2S1210 into configuration mode using the A0 and A1 inputs. Then the 8-bit address should be written to the AD2S1210 using Pin DB7 to Pin DB0, and latched using the rising edge of the WR/FSYNC input. The data can then be presented on Pin DB7 to Pin DB0 and again latched into the part using the WR/FSYNC input. Figure 28 shows the timing specifications to follow when writng to the configuration registers. Note that the RD input should be held high when writing to the AD2S1210. To read back position or velocity data from the AD2S1210, the information stored in the position and velocity registers should first be updated using the SAMPLE input. A high-to-low transition on the SAMPLE input transfers the data from the position and velocity integrators to the position and velocity registers. The fault register is also updated on the high-to-low transition of the SAMPLE input. The status of the A0 and A1 inputs determines whether the position or velocity data is transferred to the output register. The CS pin must be held low to transfer the selected data to the output register. Finally, the RD input is used to read the data from the output register and to enable the output buffer. The output buffer is enabled when CS and RD are held low. The data pins return to a high impedance state when RD returns to a high state. If the user is reading data continuously, RD can be reapplied a minimum of t20 ns after it was released. PARALLEL INTERFACE The timing requirements for the read cycle are shown in Figure 30. Note that the WR/FSYNC input should be high when RD is low. Rev. A | Page 24 of 36 AD2S1210 Clearing the Fault Register 4. The LOT pin and/or the DOS pin of the AD2S1210 are taken low to indicate that a fault has been detected. The AD2S1210 is capable of detecting eight separate fault conditions. To determine which condition triggered the fault indication, the user is required to enter configuration mode and read the fault register. To reset the fault indicators, an additional SAMPLE pulse is required. This ensures that any faults that may occur between the initial sampling and subsequent reading of the fault register are captured. Therefore, to read and clear the fault register, the following sequence of events is required: 3. 6. Figure 31 shows the timing specifications to follow when clearing the fault register. Note that the last valid register address written to the AD2S1210 prior to exiting configuration mode is again valid when reentering configuration mode. It is therefore recommended that when initial configuration of the AD2S1210 is complete, the fault address should be written to the AD2S1210 before leaving configuration mode. This simplifies the reading and clearing of the fault register in normal operation because it is now possible to access the position, velocity, and fault information by toggling the A0 and A1 pins without requiring additional register addressing. A high-to-low transition of the SAMPLE input. The SAMPLE input should be held low for t16 ns and then can be returned high. The AD2S1210 should be put into configuration mode, that is, A0 and A1 are both set to logic high. fCLKIN CLKIN t8 t1 A0, A1 CS t1 t6 t2 t5 t2 t2 t9 t7 WR t3 DB0 TO DB7 t4 ADDRESS t3 t4 DATA NOTES 1. DON’T CARE. 2. RD SHOULD BE HELD HIGH WHEN WRITING TO THE AD2S1210. Figure 28. Parallel Port Write Timing—Configuration Mode Rev. A | Page 25 of 36 ADDRESS 07467-027 1. 2. 5. The fault register should be read as described in the Reading from the AD2S1210 in Configuration Mode section. A second high-to-low transition of the SAMPLE input clears the fault indications on the DOS and/or LOT pins. Note that in the event of a persistent fault, the fault indicators are reasserted within the specified fault time latency. AD2S1210 fCLKIN CLKIN t1 A0, A1 t2 t14B t11 CS t5 t13 t15 WR t12 t10 RD t14A t14A t4 t12 t3 ADDRESS DB0 TO DB7 DATA ADDRESS DATA 07467-028 NOTES 1. DON’T CARE. Figure 29. Parallel Port Read Timing—Configuration Mode fCLKIN CLKIN t16 t16 SAMPLE t17 t6 CS t18 t20 RD t1 POSITION t19 DATA POSITION FAULT* VELOCITY t14A/t14B t21 VELOCITY FAULT* *ASSUMES FAULT REGISTER ADDRESS WRITTEN TO PART BEFORE EXITING CONFIGURATION MODE. NOTES 1. DON’T CARE. Figure 30. Parallel Port Read Timing Rev. A | Page 26 of 36 07467-029 A0, A1 AD2S1210 fCLKIN CLKIN t16 t16 t16 SAMPLE t17 CS t2 WR t9 RD t1 CONFIGURATION t3 DATA t12 t4 t14A t19 FAULT ADDRESS FAULT DATA NOTES 1. DON’T CARE. Figure 31. Parallel Port—Clear Fault Register Rev. A | Page 27 of 36 07467-030 A0, A1 AD2S1210 SERIAL INTERFACE The serial interface is selected by holding the SOE pin low. The AD2S1210 serial interface consists of four signals: SDO, SDI, WR/FSYNC, and SCLK. The SDI is used for transferring data into the on-chip registers whereas the SDO is used for accessing data from the on-chip registers, including the position, velocity, and fault registers. SCLK is the serial clock input for the device, and all data transfers (either on SDI or SDO) take place with respect to this SCLK signal. WR/FSYNC is used to frame the data. The falling edge of WR/FSYNC takes the SDI and SDO lines out of a high impedance state. A rising edge on WR/FSYNC returns the SDI and SDO to a high impedance state. The CS input is not required for the serial interface and should be held low. SDO Output In normal mode of operation, data is shifted out of the device as a 24-bit word under the control of the serial clock input, SCLK. The data is shifted out on the rising edge of SCLK. The timing diagram for this operation is shown in Figure 32. SDI Input The SDI input is used to address the on-chip registers and as a daisy-chain input in configuration mode. The data is shifted into the part on the falling edge of SCLK. The timing diagram for this operation is shown in Figure 32. Writing to the AD2S1210 The on-chip registers of the AD2S1210 can be accessed using the serial interface. To write to one of the registers, the user must first place the AD2S1210 into configuration mode using the A0 and A1 inputs. The 8-bit address should be written to the AD2S1210 using the SDI pin and latched using the rising edge of the WR/FSYNC input. The data can then be presented on the SDI pin and again latched into the part using the WR/FSYNC input. The MSB of the 8-bit write indicates whether the 8-bit word is a register address, MSB set high, or the data to be written, MSB set low. Figure 33 shows the timing specifications to follow when writing to the configuration registers. Reading from the AD2S1210 in Configuration Mode To read back data stored in one of the on-chip registers, including the fault register, the user must first place the AD2S1210 into configuration mode using the A0 and A1 inputs. The 8-bit address of the register to be read should then be written to the part, as described in the Writing to the AD2S1210 section. This transfers the relevant data to the output register. In configuration mode, the output shift register is eight bits wide. Data is shifted out of the device as an 8-bit word under the control of the serial clock input, SCLK. The timing diagram for this operation is shown in Figure 34. When reading back data from any of the read/write registers (see Table 10), the 8-bit word consists of the seven bits of data in the relevant register, D6 to D0, and an error bit, D7. If the error bit is returned high, this indicates that the data read back from the device does not match the configuration data written to the device in the previous write cycle. To read back the angular position or velocity data while in configuration mode, a falling edge of the SAMPLE input is required to update the information in the position and velocity registers. Reading from the AD2S1210 in Normal Mode To read back position or velocity data from the AD2S1210, the information stored in the position and velocity registers should first be updated using the SAMPLE input. A high-to-low transition on the SAMPLE input transfers the data from the position and velocity integrators to the position and velocity registers. The fault register is also updated on the high-to-low transition of the SAMPLE input. The status of the A0 and A1 inputs determines whether the position or velocity data is transferred to the output register. In normal mode, the output shift register is 24 bits wide. The 24-bit word consists of 16 bits of angular data (position or velocity data) followed by the 8-bit fault register data. Data is read out MSB first (Bit 23) on the SDO pin. Bit 23 through Bit 8 correspond to the angular information. The angular position data format is unsigned binary, with all 0s corresponding to 0 degrees and all 1s corresponding to 360 degrees − l LSB. The angular velocity data format is twos complement binary, with the MSB representing the rotation direction. Bit 7 through Bit 0 correspond to the fault information. If the user does not require the fault information, the WR/FSYNC can be pulled high after the16th SCLK rising edge. Clearing the Fault Register The LOT pin and/or the DOS pin of the AD2S1210 are taken low to indicate that a fault has been detected. The AD2S1210 is capable of detecting eight separate fault conditions. To determine which condition triggered the fault indication, the user is required to enter configuration mode and read the fault register. To reset the fault indicators, an additional SAMPLE pulse is required. This ensures that any faults that may occur between the initial sampling and subsequent reading of the fault register are captured. Therefore, to read and clear the fault register, the following sequence of events is required: 1. 2. 3. 4. 5. Rev. A | Page 28 of 36 A high-to-low transition of the SAMPLE input. Hold the SAMPLE input low for t16 ns and then it can be returned high. Put the AD2S1210 into configuration mode, that is, A0 and A1 are both set to logic high. Read the fault register as described in the Reading from the AD2S1210 in Configuration Mode section. A second high-to-low transition of the SAMPLE input clears the fault indications on the DOS and/or LOT pins. Note that in the event of a persistent fault, the fault indicators are reasserted within the specified fault time latency. AD2S1210 WR/FSYNC t22 t 29 fSCLK t25 SCLK t23 t24 t26 MSB LSB t27 t28 MSB SDI 07467-031 SDO LSB Figure 32. Serial Interface Timing Diagram fCLKIN CLKIN t1 t1 t8 A0, A1 t5 t2 CS t2 t7 t9 WR/FSYNC SDI ADDRESS DATA NEW ADDRESS OLD DATA OLD DATA COPY OF DATA NOTES 1. DON’T CARE. 07467-032 SDO Figure 33. Serial Interface Write Timing—Configuration Mode fCLKIN CLKIN A0, A1 t1 t5 t6 t2 t5 CS t2 WR/FSYNC ADDRESS 1 ADDRESS 2 ADDRESS 3 SDO OLD DATA DATA 1 DATA 2 07467-033 SDI NOTES 1. DON’T CARE. Figure 34. Serial Interface Read Timing—Configuration Mode Rev. A | Page 29 of 36 AD2S1210 fCLKIN CLKIN t16 t16 SAMPLE t30 t6 CS t31 t34 WR/FSYNC t32 A0, A1 t33 POSITION VELOCITY FAULT* t29 t23 SDO POSITION VELOCITY FAULT* 07467-034 *ASSUMES FAULT REGISTER ADDRESS WRITTEN TO PART BEFORE EXITING CONFIGURATION MODE. NOTES 1. DON’T CARE. Figure 35. Serial Interface Read Timing Rev. A | Page 30 of 36 AD2S1210 INCREMENTAL ENCODER OUTPUTS SUPPLY SEQUENCING AND RESET The A, B, and NM incremental encoder emulation outputs are free running and are valid if the resolver format input signals applied to the converter are valid. The AD2S1210 requires an external reset signal to hold the RESET input low until VDD is within the specified operating range of 4.5 V to 5.5 V. The AD2S1210 can be configured to emulate a 256-line, a 1024-line, a 4096-line, or a 16,384-line encoder. For example, if the AD2S1210 is configured for 12-bit resolution, one revolution produces 1024 A and B pulses. Pulse A leads Pulse B for increasing angular rotation (that is, clockwise direction). The RESET pin must be held low for a minimum of 10 μs after VDD is within the specified range (shown as tRST in Figure 37). Applying a RESET signal to the AD2S1210 initializes the output position to a value of 0x000 (degrees output through the parallel, serial, and encoder interfaces) and causes LOS to be indicated (LOT and DOS pins pulled low), as shown in Figure 37. The resolution of the encoder emulation outputs of the AD2S1210 is generally configured to match the resolution of the digital output. However, the encoder emulation outputs of the AD2S1210 can also be configured to have a lower resolution than the digital outputs. For example, if the AD2S1210 is configured for 16-bit resolution, then the encoder emulation outputs can also be configured for 14-bit, 12-bit, or 10-bit resolution. However, the resolution of the encoder emulation outputs cannot be higher than the resolution of the digital output. If the AD2S1210 is configured such that the resolution of the encoder emulation outputs is higher than the resolution of the digital outputs, the AD2S1210 internally overrides this configuration. In this event, the resolution of the encoder outputs is set to match the resolution of the digital outputs. The resolution of the encoder emulation outputs can be programmed by writing to Bit D3 and Bit D2 of the control register. The north marker pulse is generated as the absolute angular position passes through zero. The north marker pulse width is set internally for 90° and is defined relative to the A cycle. Figure 36 details the relationship between A, B, and NM. Failure to apply the correct power-up/reset sequence may result in an incorrect position indication. After a rising edge on the RESET input, the device must be allowed at least tTRACK ms (see Figure 37) for the internal circuitry to stabilize and the tracking loop to settle to the step change of the input position. For the duration of tTRACK fault indications may occur on the LOT and DOS pins due to the step response caused by the RESET. The duration of tTRACK is dependent on the converter resolution as outlined in Table 27. After tTRACK, the fault register should be read and cleared as outlined in the Clearing the Fault Register section. The time required to read and clear the fault register is indicated as tFAULT, and is defined by the interface speed of the DSP/microprocessor used in the application. (Note that if position data is acquired via the encoder outputs, these can be monitored during tTRACK.) Table 27. tTRACK vs. Resolution (fCLKIN = 8.192 MHz) Resolution (Bits) 10 12 14 16 A VDD B tTRACK (ms) 10 20 25 60 4.75V tRST 07467-035 RESET tFAULT SAMPLE Figure 36. A, B, and NM Timing for Clockwise Rotation The inclusion of A and B outputs allows the AD2S1210 with resolver solution to replace optical encoders directly without the need to change or upgrade existing application software. LOT VALID OUTPUT DATA DOS Figure 37. Power Supply Sequencing and Reset Rev. A | Page 31 of 36 07457-036 NM tTRACK AD2S1210 CIRCUIT DYNAMICS RDC closed-loop transfer function LOOP RESPONSE MODEL θIN k1 × k2 – c 1 – z–1 H (z ) = VELOCITY 1 – az–1 1 – bz–1 c 1 – z–1 θOUT 07467-037 ERROR (ACCELERATION) Sin/Cos LOOKUP Figure 38. RDC System Response Block Diagram The following equations outline the transfer functions of the individual blocks as shown in Figure 38, which then combine to form the complete RDC system loop response. To convert G(z) into the s-plane, an inverse bilinear transformation is performed by substituting the following equation for z: 2 +s z= t 2 −s t Substitution yields the open-loop transfer function, G(s). G( s ) = 1 − az −1 1 − bz −1 t1 = (11) t2 = RDC open-loop transfer function G(z ) = k1 × k2 × I (z ) 2 × C(z ) (15) K a 1 + st1 × s 2 1 + st 2 (16) where: Compensation filter transfer function C (z ) = k1 × k2(1 − a) × a −b s 2t 2 1 + s × t (1 + a) 2(1 − a) 4 × t (1 + b) s2 1+ s× 2(1 − b) 1 + st + This transformation produces the best matching at low frequencies (f < fSAMPLE). At such frequencies (within the closed-loop bandwidth of the AD2S1210), the transfer function can be simplified to G( s ) ≅ (10) (14) where t is the sampling period (1/4.096 MHz ≈ 244 ns). Integrator1 and Integrator2 transfer function c I (z ) = 1 − z −1 (13) The closed-loop magnitude and phase responses are that of a second-order low-pass filter (see Figure 11 and Figure 12). The RDC is a mixed-signal device that uses two ADCs to digitize signals from the resolver and a Type II tracking loop to convert these to digital position and velocity words. The first gain stage consists of the ADC gain on the sine/cosine inputs and the gain of the error signal into the first integrator. The first integrator generates a signal proportional to velocity. The compensation filter contains a pole and a zero that are used to provide phase margin and reduce high frequency noise gain. The second integrator is the same as the first and generates the position output from the velocity signal. The sin/cos lookup has unity gain. The values for the k1, k2, a, b, and c parameters are outlined in Table 28. G( z ) 1 + G( z ) t (1 + a) 2(1 − a) t (1 + b) 2(1 − b) Ka = (12) k1 × k2(1 − a) a −b Solving for each value gives t1, t2, and Ka as outlined in Table 29. Table 28. RDC System Response Parameters Parameter k1 (nominal) k2 a b c Description ADC gain Error gain Compensator zero coefficient Compensator pole coefficient Integrator gain 10-bit resolution 1.8/2.5 6 × 106 × 2π 8187/8192 509/512 1/1,024,000 12-bit resolution 1.8/2.5 18 × 106 × 2π 4095/4096 4085/4096 1/4,096,000 Rev. A | Page 32 of 36 14-bit resolution 1.8/2.5 82 x 106 × 2π 8191/8192 16,359/16,384 1/16,384,000 16-bit resolution 1.8/2.5 66 × 106 × 2π 32,767/32,768 32,757/32,768 1/65,536,000 AD2S1210 Table 29. Loop Transfer Function Parameters vs. Resolution (fCLKIN = 8.192 MHz) Resolution (Bits) 10 12 14 16 t1 (ms) 0.4 1 2 8 t2 (ms) 42 91 160 728 −2 Ka (sec ) 39.6 × 106 6.5 × 106 1.6 × 106 92.7 × 103 SOURCES OF ERROR Acceleration A tracking converter employing a Type II servo loop does not have a lag in velocity. There is, however, an error associated with acceleration. This error can be quantified using the acceleration constant (Ka) of the converter. Ka = Note that the closed-loop response is described as H (s ) = G( s ) 1 + G( s ) (17) By converting the calculation to the s-domain, it is possible to quantify the open-loop dc gain (Ka). This value is useful to calculate the acceleration error of the loop (see the Sources of Error section). The step response to a 10° input step is shown in Figure 10, Figure 11, Figure 12, and Figure 13. The step response to a 179° input step is shown in Figure 14, Figure 15, Figure 16, and Figure 17. In response to a step change in velocity, the AD2S1210 exhibits the same response characteristics as it does for a step change in position. Figure 18 and Figure 19 in the Typical Performance Characteristics section show the magnitude and phase responses of the AD2S1210 for each resolution setting. Input Acceleration (18) Tracking Error Conversely, Tracking Error = Input Acceleration Ka (19) The units of the numerator and denominator must be consistent. The maximum acceleration of the AD2S1210 is defined by the maximum acceptable tracking error in the users application. For example, if the maximum acceptable tracking error is 5°, then the maximum acceleration is defined as the acceleration that creates an output position error of 5° (that is, when LOT is indicated). An example of how to calculate the maximum acceleration in a 12-bit application with a maximum tracking error of 5° is Maximum Acceleration = K a (sec−2 ) × 5° ≅ 90,300 rps2 360(°/rev ) (20) Figure 20 to Figure 23 in the Typical Performance Characteristics section show the tracking error vs. acceleration response of the AD2S1210 for each resolution setting. Rev. A | Page 33 of 36 AD2S1210 OUTLINE DIMENSIONS 9.20 9.00 SQ 8.80 1.60 MAX 37 48 36 1 PIN 1 0.15 0.05 7.20 7.00 SQ 6.80 TOP VIEW 1.45 1.40 1.35 0.20 0.09 7° 3.5° 0° 0.08 COPLANARITY SEATING PLANE VIEW A (PINS DOWN) 25 12 13 VIEW A 0.50 BSC LEAD PITCH 24 0.27 0.22 0.17 ROTATED 90° CCW COMPLIANT TO JEDEC STANDARDS MS-026-BBC 051706-A 0.75 0.60 0.45 Figure 39. 48-Lead Low Profile Quad Flat Package [LQFP] (ST-48) Dimensions shown in millimeters ORDERING GUIDE Model 1 AD2S1210ASTZ AD2S1210BSTZ AD2S1210CSTZ AD2S1210DSTZ AD2S1210WDSTZ 2 AD2S1210WDSTZRL72 EVAL-AD2S1210EDZ 1 2 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C Package Description 48-Lead LQFP 48-Lead LQFP 48-Lead LQFP 48-Lead LQFP 48-Lead LQFP 48-Lead LQFP Evaluation Board Z = RoHS Compliant Part. Qualified for Automotive. Rev. A | Page 34 of 36 Package Option ST-48 ST-48 ST-48 ST-48 ST-48 ST-48 AD2S1210 NOTES Rev. A | Page 35 of 36 AD2S1210 NOTES ©2008–2010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D07467-0-2/10(A) Rev. A | Page 36 of 36