AP9211 SINGLE CHIP SOLUTION FOR 1-CELL Li+ BATTERY PACK Description Pin Assignments The AP9211 is a single chip protection solution specially designed for 1-cell Li+ rechargeable battery pack application. (Top View) The AP9211 includes a 1-cell Lithium ion battery protection chip and dual N-CHANNEL MOSFET with common drain. The AP9211 provides rich battery protection features and can turn-off the N-CHANNEL MOSFET by detecting overcharge voltage/current, over discharge voltage/current, or load short circuit. AP9211 has builtin fixed delay time to save external components. 6 S2 2 5 VM 3 4 NC S1 1 VSS VDD EP The AP9211 is available in U-DFN2030-6 package. U-DFN2030-6 Features Applications High Voltage CMOS Process, up to 30V (VDD to VM) Low Quiescent Current (+25°C ) Li+ Rechargeable Battery Pack In Normal Mode, 3.0µA (Typ.), 4.5µA (Max.) VDD = 3.5V In Power-Down Mode, 0.1µA (Max.) High-Accuracy Voltage Detection Circuit (+25°C) Overcharge Detection Voltage: 3.5V to 4.5V (5mV Steps) Accuracy ±25mV Overcharge Hysteresis Voltage Range: 0.1V to 0.4V (50mV Steps) Accuracy ±50mV Overdischarge Detection Voltage: 2.0V to 3.4V (10mV Steps) Accuracy ±35mV Overdischarge Hysteresis Voltage Range: 0V to 0.7V (40mV Steps) Accuracy ±65mV Discharge Overcurrent Detection Voltage: 0.05V to 0.32V (10mV Steps) Accuracy ±15mV Short Current Detection Voltage: 0.45V to 0.7V (50mV Steps) Accuracy ±100mV Charge Overcurrent Detection Voltage: -0.2V to -0.05V (10mV Steps) Accuracy ±15mV Overcharger Detection Voltage: 8.0V (Fixed) Accuracy ±2V Overcharger Release Voltage: 7.3V (Fixed) Accuracy ±2V Built-in Fixed Detection Delay Time (+25°C ), Accuracy ±20% Power-Down Mode Selectable (Yes or No) 0V Battery Charge Selectable (Permission or Inhibition) Overcharge Protection Mode Selectable (Auto Release or Latch) Totally Lead-free & Fully RoHS Compliant (Notes 1 & 2) Halogen and Antimony Free. “Green” Device (Note 3) Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. 2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds. AP9211 Document number: DS37596 Rev. 2 - 2 1 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Typical Applications Circuit (Note 4) P+ R1 330ohm to 470ohm 3 BAT VDD C1 100n 2 VSS U1 AP9211 (U-DFN2030-6) S1 1 VM 5 R2 2.7kohm S2 P- 6 Note: 4. R1 and C1 are used to stabilize the supply voltage of the AP9211. The recommended range of R1 value is 330Ω to 470Ω and C1 value is 10nF to 1000nF, typical value is 100nF. R2 should be connected between P- to VM sense terminal to monitor the status of charger and the charge/discharge current. The R2 should be between 300Ω and 4kΩ, typical value is 2.7kΩ. R1 and R2 are also used as current limit resistors if the battery or charger is connected reversely. Polarity reversing may cause the power consumption of R1 and R2 to go over their power dissipation rating, therefore R1 and R2 values should be selected appropriately for the actual application. If R2 is more than 4kΩ resistor, charge may not be off due to the voltage drop on R2. For power down mode, when first connecting AP9211 system board to the battery, it is necessary to use charger or to short P- to the battery negative polarity. Once the AP9211 is activated, the charger or connection can be removed, otherwise the battery cannot discharge current through system board. The values selected should follow the recommended typical range mentioned above. It has not been confirmed whether the operation is normal or not in circuits other than the above example of connection. In addition, the example of connection shown above and the typical value do not exactly guarantee proper operation. Please perform the actual application to set the suitable value through your complete evaluation. Pin Descriptions Pin Number Pin Name 1 S1 Source pin of discharging MOSFET, connecting this pin to battery negative pole. 2 VSS Negative power supply pin 3 VDD Positive power supply pin, connecting this pin to battery positive pole through R1 4 NC Not connected, leave this pin floating 5 VM Charger negative input pin, short this pin to S2 pin through R2 6 S2 Source pin of charging MOSFET, connecting this pin to charge negative input. EP D Thermal PAD is common drain of charge and discharge MOSFET, so in PCB layout, prefer to use large copper area to cover this pad for better thermal dissipation, then leave it open. AP9211 Document number: DS37596 Rev. 2 - 2 Function 2 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Functional Block Diagram Logic Circuit OV Charge Option 3 VDD Level Shift Delay Time Circuit VM 2 5 RVMD Logic Circuit RVMS G1 S1 1 VSS S1 G2 D1 D2 S2 6 S2 EP D AP9211 Document number: DS37596 Rev. 2 - 2 3 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Absolute Maximum Ratings (Notes 5 & 6) Symbol Parameter Rating Unit VDS Supply Voltage (Between VDD and VSS) -0.3 to 12 V VDM Charge Input Voltage (Between VDD and VM for Protection Chip) -0.3 to 24 V VDSS MOSFET Drain-to-Source Voltage 24 V VGSS MOSFET Gate-to-Source Voltage ±12 V Continuous Drain Current, VGS = 4.5V, TA = +25°C 9.0 A Continuous Drain Current, VGS = 4.5V, TA = +70°C 7.1 A ID PD Power Dissipation 1,000 mW TJ Maximum Junction Temperature +150 °C -65 to +150 °C 300 V 3,000 V TSTG Notes: Storage Temperature Range — ESD (Machine Model) — ESD (Human Body Model) 5. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 6. Ratings apply to ambient temperature at +25°C. The JEDEC High-K board design used to derive this data was a 2 inch x 2 inch multilayer board with 2ounce internal power and ground planes and 2-ounce copper traces on the top and bottom of the board. Recommended Operating Conditions Symbol Parameter Min Max Unit VDS Supply Voltage (Between VDD and VSS) 1.5 5.5 V VDM Charge Input Voltage (between VDD and VM) -0.3 5.5 V Operating Ambient Temperature -40 +85 °C TA AP9211 Document number: DS37596 Rev. 2 - 2 4 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Electrical Characteristics Symbol (TA = +25°C, VDD = 3.5V, VSS = 0V, R1 = 220Ω, R2 = 1.0kΩ, C1 = 100nF, unless otherwise specified) Parameter VCU Overcharge Detection Voltage VCL Overcharge Release Voltage Conditions － VCL ≠ VCU VCL = VCU VDL Overdischarge Detection Voltage VDU Overdischarge Release Voltage － VDU ≠ VDL VDU = VDL Discharge Overcurrent Detection Voltage － VSHORT Load Short-Circuiting Detection Voltage － VCOC Charge Overcurrent Detection Voltage － ICC Current Consumption During Operation VDD=3.5V VM=0V ISTB Current Consumption at Power Down VDOC VDD=1.8V Power Down Mode VM Pin Without Power Down Floating Mode (Auto Wake up) VDD=1.8V VM=0V VDD=3.5V VM=1.0V Min VCU - 0.025 VCL - 0.050 VCL - 0.025 VDL - 0.035 VDU - 0.100 VDU - 0.035 VDOC -0.015 VSHORT -0.10 VCOC -0.015 Typ VCU VCL VCL VDL VDU VDU VDOC VSHORT VCOC Max VCU + 0.025 VCL + 0.050 VCL + 0.025 VDL + 0.035 VDU + 0.100 VDU + 0.035 VDOC +0.015 VSHORT +0.10 VCOC +0.015 Units V V V V V V V V V 1.5 3.0 4.5 μA － － 0.1 μA － － 5.5 μA 150 300 500 kΩ 10 30 50 kΩ 1.2 － － V RVMD Resistance Between VM Pin and VDD Pin RVMS Resistance Between VM Pin and VSS Pin V0CHA 0V Battery Charge Starting Charge Voltage V0INH 0V Battery Charge Inhibition Battery Voltage 0V battery charging “unavailable” － － 0.45 V VOVCHG Overvoltage Charge Detection Voltage VDD=3.5V 6.0 8.0 10.0 V VOVCHGR Overvoltage Charge Release Voltage VDD=3.5V 5.3 7.3 9.3 V tCU Overcharge Detection Delay Time － tCU * 0.8 tCU tCU * 1.2 ms tCUR Overcharge Release Delay Time － tCUR * 0.8 tCUR tCUR * 1.2 ms tDL Overdischarge Detection Delay Time － tDL * 0.8 tDL tDL * 1.2 ms tDLR Overdischarge Release Delay Time － tDLR * 0.8 tDLR tDLR * 1.2 ms tDOC Discharge Overcurrent Detection Delay Time － tDOC * 0.8 tDOC tDOC * 1.2 ms tDOCR Discharge Overcurrent Release Delay Time － tDOCR * 0.8 tDOCR tDOCR * 1.2 ms tSHORT Load Short Detection Delay Time － tSHORT * 0.8 tSHORT tSHORT * 1.2 μs tCOC Charge Overcurrent Detection Delay Time － tCOC * 0.8 tCOC tCOC * 1.2 ms tCOCR Charge Overcurrent Release Delay Time － tCOCR * 0.8 tCOCR tCOCR * 1.2 ms AP9211 Document number: DS37596 Rev. 2 - 2 0V battery charging “available” 5 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Electrical Characteristics (continued) (TA = -40°C to +85°C, VDD = 3.5V, VSS = 0V, R1 = 220Ω, R2 = 1.0kΩ, C1 = 100nF, unless otherwise specified) Symbol Parameter VCU Overcharge Detection Voltage VCL Overcharge Release Voltage Conditions － VCL ≠ VCU VCL = VCU VDL Overdischarge Detection Voltage VDU Overdischarge Release Voltage － VDU ≠ VDL VDU = VDL Discharge Overcurrent Detection Voltage － VSHORT Load Short-Circuiting Detection Voltage － VCOC Charge Overcurrent Detection Voltage － ICC Current Consumption During Operation VDD=3.5V VM=0V ISTB Current Consumption at Power Down VDOC RVMD RVMS V0CHA V0INH VDD =1.8V Power Down Mode VM Pin Without Power Down Floating Mode (Auto Wake up) VDD=1.8V Resistance between VM Pin and VDD Pin VM=0V VDD=3.5V Resistance between VM Pin and VSS Pin VM=1.0V 0V battery charging 0V Battery Charge Starting Charge Voltage “available” 0V battery charging 0V Battery Charge Inhibition Battery Voltage “unavailable” Min VCU - 0.060 VCL - 0.080 VCL - 0.060 VDL - 0.080 VDU - 0.150 VDU - 0.080 VDOC -0.021 VSHORT -0.34 VCOC -0.040 Typ VCU VCL VCL VDL VDU VDU VDOC VSHORT VCOC Max VCU + 0.040 VCL + 0.065 VCL + 0.040 VDL + 0.080 VDU + 0.190 VDU + 0.080 VDOC +0.024 VSHORT +0.34 VCOC +0.040 Units V V V V V V V V V 1.0 3.0 7.0 μA － － 1.0 μA － － 8 μA 100 300 650 kΩ 5 30 65 kΩ 1.2 － － V － － 0.3 V VOVCHG Overvoltage Charge Detection Voltage VDD=3.5V 5.5 8.0 10.5 V VOVCHGR Overvoltage Charge Release Voltage VDD=3.5V 5.0 7.3 9.5 V tCU Overcharge Detection Delay Time － tCU * 0.6 tCU tCU * 1.4 ms tCUR Overcharge Release Delay Time － tCUR * 0.6 tCUR tCUR * 1.4 ms tDL Overdischarge Detection Delay Time － tDL * 0.6 tDL tDL * 1.4 ms tDLR Overdischarge Release Delay Time － tDLR * 0.6 tDLR tDLR * 1.4 ms tDOC Discharge Overcurrent Detection Delay Time － tDOC * 0.6 tDOC tDOC * 1.4 ms tDOCR Discharge Overcurrent Release Delay Time － tDOCR * 0.6 tDOCR tDOCR * 1.4 ms tSHORT Load Short Detection Delay Time － tSHORT * 0.6 tSHORT tSHORT * 1.4 μs tCOC Charge Overcurrent Detection Delay Time － tCOC * 0.6 tCOC tCOC * 1.4 ms tCOCR Charge Overcurrent Release Delay Time － tCOCR * 0.6 tCOCR tCOCR * 1.4 ms AP9211 Document number: DS37596 Rev. 2 - 2 6 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Electrical Characteristics (continued) (Notes 7 & 8) (TA = +25°C, VDD = 3.5V, VSS = 0V, R1 = 220Ω, R2 = 1.0kΩ, C1 = 100nF, unless otherwise specified) Symbol Parameter Conditions Min Typ Max Units Zero Gate Voltage Drain Current VDS = 20V, VGS=0 – – 1.0 μA RSS(ON)1 Static Source-Source On-Resistance 1 VDD = 4.0V ID = 1.0A 20 27 30 mΩ RSS(ON)2 Static Source-Source On-Resistance 2 VDD = 3.9V ID = 1.0A 21 27 31 mΩ RSS(ON)3 Static Source-Source On-Resistance 3 VDD = 3.0V ID = 1.0A 21 28 33 mΩ Diode Forward Voltage VGS = 0V (Note 6) IS = 1A – 0.75 1.0 V IDSS VSD Notes: 7. In case of Gate-Source voltage of charging MOSFET is 0V. In case of Gate-Source voltage of discharging MOSFET is 0V. 8. These specifications are guaranteed by design - will not be tested in production. AP9211 Document number: DS37596 Rev. 2 - 2 7 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Application Information Operation Mode 1. Normal Status The AP9211 monitors the battery voltage between the V DD pin and VSS pin as well as the voltage difference between the V M pin and VSS pin to control battery charging and discharging. When the battery voltage is between overdischarge detection voltage (V DL) and overcharge detection voltage (VCU) as well as the VM pin voltage is between the charge overcurrent detection voltage (VCOC) and discharge overcurrent detection voltage (VDOC), the AP9211 will turn on discharging and charging MOSFET. In these conditions, the battery can charge and discharge freely. Also, RVMD does not connect to VDD pin and RVMS does not connect to VSS pin in this status. 2. Overcharge Status If the battery voltage is more than VCU during charging status for the overcharge detection delay time (tCU) or longer, the AP9211 turns off the charging MOSFET to stop charging. RVMD and RVMS are not connected in overcharge status. When VM pin voltage is lower than VDOC and battery voltage falls below VCL, the AP9211 will release from overcharge status. When VM pin voltage is equal or more than VDOC and battery voltage falls below VCU, the AP9211 will release from overcharge status. 3. Overdischarge Status If the battery voltage is less than VDL during discharging status for the overdischarge detection delay time (tDL) or longer, the AP9211 turns off the discharging MOSFET to stop discharging. In overdischarge status, RVMD is connected to VDD and VM pin voltage is pulled up to VDD by RVMD, but RVMS is not connected. For power-down mode version, the AP9211 recovers normal status from overdischarge status only by charging the battery through the charger. When VM pin voltage to VSS pin voltage is less than typical -0.7V and the battery voltage rises over VDL, the AP9211 will release from overdischarge status. If VM pin voltage to VSS pin voltage is higher than typical -0.7V, the AP9211 will release from overdischarge status until the battery voltage rises over VDU. For auto-wake-up version AP9211SA, the device recovers to normal status from overdischarge status if either of these two conditions are satisfied: If charger is connected: the AP9211SA overdischarge status is released in the same way as described above in AP9211S Overdischarge Status section. If no charger is connected: 1) The battery voltage reaches the overdischarge release voltage (VDU) or higher; 2) Maintains continuous time more than overdischarge release delay time tDLR. 4. Discharge Overcurrent and Short Current Status When battery is in discharge overcurrent status, if the voltage of the VM pin to VSS pin is equal or more than VDOC to VSHORT and detection lasts for the discharge overcurrent detection delay time (tDOC) or longer, the AP9211 turns off the discharging MOSFET to stop discharging. When the battery is in short current status, if the voltage of the VM pin to VSS pin is equal to or more than VSHORT, and the detection lasts for the short current detection delay time or longer, the AP9211 turns off the discharge MOSFET to stop discharging. In discharge overcurrent or short current status, RVMS is connected to VSS but RVMD is not connected. The voltage of VM pin is almost equal to VDD as long as the load is connected. When the load is disconnected, the voltage of V M pin will become almost equal to VSS (due to RVMS being connected) and then the AP9211 will release from discharge overcurrent or short current status. 5. Charge Overcurrent Status When the battery is in charge current status, if the voltage of the VM pin to VSS pin is equal to or less than VCOC and the detection continues for the charge overcurrent detection delay time (tCOC) or longer, the AP9211 turns off the charging MOSFET to stop charging. 6. 0V Battery Charging Function (Option) This function is available as an option and can be factory set internally. AP9211 has this function built in. 0V charging function permits charger to recharge the battery whose voltage is 0V due to self-discharge. If 0V charging function is not present, the device will prevent charger to recharge the battery whose voltage is 0V due to self-discharge. (If a device without 0V charging function is needed, please contact Diodes sales team) AP9211 Document number: DS37596 Rev. 2 - 2 8 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Operation Description (Continued) 7. Overvoltage Charger Detection Circuit This function is used to monitor the charger voltage between the VDD pin and VM pin, and when this voltage exceeds overvoltage charger detection voltage (8.0V Typ.), the AP9211 will turn off charging MOSFET, when this voltage drops below overvoltage charger release voltage (7.3V Typ.), it then turns on charging MOSFET. There are no delay times set for detection and release. 8. Power-Down Mode or Auto-Wake-Up Function Option In device with power-down function, during power-down mode, device enters the overdischarge status. The IC enters sleep mode and the current consumption becomes very low, typically 0.1µA. To release from power-down status to the normal status, charger connection is required. In device with auto-wakeup mode, the IC remains active in the overdischarge state. The IC is released into the normal state by the operation that increases the battery voltage more than overdischarge release voltage. AP9211 Document number: DS37596 Rev. 2 - 2 9 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Application Information (Timing Chart) 1. Overcharge and Overdischarge Detection VCU VCL VDD VDU VDL VSS VDD DO VSS VDD Red line is for no shutdown mode version CO VVM VDD VM VDOC VSS VCOC VP2 S1 1 3 S2 2 4 S1 P1 1: tDL 2: tCU 3: tCUR 4: tDLR AP9211 Document number: DS37596 Rev. 2 - 2 3 1 3 S2 P1 S1: Charger connection S2: Load connection P1: RVMD pull-up connection 10 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Application Information (Timing Chart) (continued) 2. Discharge Overcurrent Detection VCU VCL VDD VDU VDL VSS ON Discharge FET OFF ON Charge FET OFF VDD VSHORT VM VDOC VSS 1 1 3 S1 AP9211 Document number: DS37596 Rev. 2 - 2 3 S2 P1 1: tDOC 2: tSHORT 3: tDOCR 2 P1 S1: Connect over current load S2: Connect short current load P1: RVMS pull-down connection 11 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Application Information (Timing Chart) (cont.) 3. Charge Overcurrent Detection VCU VCL VDD VDU VDL VSS VDD Discharge FET VSS VDD Charge FET VVM VDD VM VSS VCOC VP1 2 S1 1: tCOC 2: tCOCR AP9211 Document number: DS37596 Rev. 2 - 2 S1: Connect over current charger 12 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Ordering Information (Note 9) AP9211X X - XX - XXX - X RSS(ON) Power Down Mode Product Code Package Packing S: Standard Blank: Yes A: No (Auto-wake-up) Voltage & Delay Time Combination Code HAC: U-DFN2030-6 7: Tape & Reel Part Number Package Code Packaging 7” Tape and Reel Quantity AP9211XX-XX-HAC-7 HAC U-DFN2030-6 3,000/Tape & Reel Voltage Combination Part Number Overcharge Detection Voltage Overcharge Release Voltage VCU VCL Overdischarge Detection Voltage Overdischarge Release Voltage Discharge Overcurrent Detection Voltage VDL VDU VDOC Charge Load Short Overurrent Detection Detection Voltage Voltage VSHORT VCOC Over Over Voltage Charger Detection Voltage Voltage Charger Release Voltage VOVCHG VOVCHGR Power-down Function Overcharge Protection Mode Delay Time 0V Battery Charge Function AP9211XX-AA-HAC-7 4.375V 4.175V 2.500V 2.900V 0.150V 0.700V -0.150V 8.0V 7.3V Selectable Auto Release Option 1 Permission AP9211XX-AB-HAC-7 4.425V 4.225V 2.500V 2.900V 0.150V 0.700V -0.150V 8.0V 7.3V Selectable Auto Release Option 1 Permission AP9211XX-AC-HAC-7 4.375V 4.175V 2.500V 2.900V 0.095V 0.700V -0.095V 8.0V 7.3V Auto Release Option 1 Permission AP9211XX-AD-HAC-7 4.375V 4.175V 2.500V 2.900V 0.120V 0.700V -0.120V 8.0V 7.3V Auto Release Option 1 Permission AP9211XX-AE-HAC-7 4.200V 4.100V 2.500V 3.000V 0.300V 0.550V -0.100V 8.0V 7.3V Auto Release Option 1 Permission AP9211XX-AF-HAC-7 4.375V 4.175V 2.500V 2.900V 0.180V 0.700V -0.180V 8.0V 7.3V Auto Release Option 1 Permission AP9211XX-AG-HAC-7 4.375V 4.175V 2.500V 2.900V 0.075V 0.700V -0.075V 8.0V 7.3V Auto Release Option 1 Permission AP9211XX-AH-HAC-7 4.425V 4.225V 2.500V 2.900V 0.075V 0.700V -0.075V 8.0V 7.3V Auto Release Option 1 Permission AP9211XX-AI-HAC-7 4.500V 4.300V 2.400V 2.800V 0.150V 0.700V -0.075V 8.0V 7.3V Auto Release Option 1 Permission AP9211XX-AJ-HAC-7 4.375V 4.175 V 2.400V 2.800V 0.125V 0.700V - 0.125V 8.0V 7.3V Auto Release Option 1 Permission AP9211XX-AK-HAC-7 4.250V 4.050 V 2.400V 3.000V 0.150V 0.700V - 0.150V 8.0V 7.3V Auto Release Option 1 Permission AP9211XX-AL-HAC-7 4.275V 4.175V 2.300V 2.400V 0.180V 0.700V -0.180V 8.0V 7.3V Auto Release Option 1 Permission AP9211XX-AM-HAC-7 4.375V 4.175V 2.300V 2.400V 0.180V 0.700V -0.180V 8.0V 7.3V Auto Release Option 1 Permission AP9211XX-AN-HAC-7 4.225V 4.025V 3.200V 3.400V 0.060V 0.450V -0.060V 8.0V 7.3V Auto Release Option 1 Permission Note: Selectable Selectable Selectable Selectable Selectable Selectable Selectable Selectable Selectable Selectable Selectable Selectable 9. Current voltage versions are built by delay time option 1. If any other voltage versions or delay time option products are needed, please contact with the local sale’s office. AP9211 Document number: DS37596 Rev. 2 - 2 13 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Ordering Information (Note 7, continued) AP9211 Delay Time Combination Part Number AP9211XX-XX-HAC-7 Overcharge Overcharge Overdischarge Detection Release Detection Delay Time Delay Time Delay Time Overdischarge Release Delay Time tCU tCUR tDL tDLR 1.0s 2.0ms 115ms 2.0ms Discharge Overcurrent Detection Delay Time Discharge Overcurrent Release Delay Time Charge Overcurrent Detection Delay Time Charge Overcurrent Release Delay Time tDOC tDOCR tCOC tCOCR 10.0ms 2.0ms 10.0ms 2.0ms Load Short Detection Delay Time tSHORT 360µs Other Delay Time Combination Table (Optional) Overcharge Overdischarge Discharge Over Charge Over Load Short Circuiting Detection Delay Detection Delay Current Detection Current Detection Detection Delay Time Time (tCU) Time (tDL) Delay Time (tDOC) Delay Time (tCOC) (tSHORT) 1 1s 115ms 10ms 10ms 360µs 2 125ms 32ms 8ms 8ms 180µs 3 1s 20ms 12ms 10ms 360µs 4 1s 42ms 10ms 10ms 360µs 5 1s 115ms 10ms 10ms 180µs Delay Time Option AP9211 Document number: DS37596 Rev. 2 - 2 14 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Marking Information (Top View) XX YWX XX : Identification Code Y : Year : 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : A~Z : Internal Code Part Number Package Identification Code AP9211S-AA-HAC-7 AP9211S-AB-HAC-7 U-DFN2030-6 U-DFN2030-6 P5 P6 AP9211S-AC-HAC-7 AP9211S-AD-HAC-7 U-DFN2030-6 U-DFN2030-6 6B 6C AP9211S-AE-HAC-7 AP9211S-AF-HAC-7 U-DFN2030-6 U-DFN2030-6 6D 6E AP9211S-AG-HAC-7 AP9211S-AH-HAC-7 U-DFN2030-6 U-DFN2030-6 6F 6G AP9211S-AI-HAC-7 AP9211S-AJ-HAC-7 U-DFN2030-6 U-DFN2030-6 6H 6Y AP9211S-AK-HAC-7 AP9211S-AL-HAC-7 U-DFN2030-6 U-DFN2030-6 6Z 5T AP9211S-AM-HAC-7 AP9211S-AN-HAC-7 U-DFN2030-6 U-DFN2030-6 5U 5V AP9211SA-AA-HAC-7 AP9211SA-AB-HAC-7 U-DFN2030-6 U-DFN2030-6 M3 M4 AP9211SA-AC-HAC-7 AP9211SA-AD-HAC-7 U-DFN2030-6 U-DFN2030-6 M6 M7 AP9211SA-AE-HAC-7 AP9211SA-AF-HAC-7 U-DFN2030-6 U-DFN2030-6 M8 N3 AP9211SA-AG-HAC-7 AP9211SA-AH-HAC-7 U-DFN2030-6 U-DFN2030-6 N4 N6 AP9211SA-AI-HAC-7 AP9211SA-AJ-HAC-7 U-DFN2030-6 U-DFN2030-6 N7 N8 AP9211SA-AK-HAC-7 AP9211SA-AL-HAC-7 U-DFN2030-6 U-DFN2030-6 NE 7X AP9211SA-AM-HAC-7 AP9211SA-AN-HAC-7 U-DFN2030-6 U-DFN2030-6 P7 P8 AP9211 Document number: DS37596 Rev. 2 - 2 15 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Package Outline Dimensions Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. A1 A3 A Seating Plane D e1 L e 1 R0.1 50 Pin1 ID E2 E D2 z b2 U-DFN2030-6 (Type C) Dim Min Max Typ A 0.50 0.60 -A1 0.00 0.05 0.02 A3 --0.127 b 0.25 0.35 0.30 b2 0.60 0.70 0.65 D 1.90 2.10 2.00 D2 1.60 1.80 1.70 E 2.90 3.10 3.00 E2 1.60 1.80 1.70 e --0.60 e1 --0.775 L 0.25 0.35 0.30 z 0.0500 Ref All Dimensions in mm b Suggested Pad Layout Please see AP02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version. G1 X1 X Y Dimensions C C1 G G1 X X1 X2 Y Y1 G Y1 X2 C1 AP9211 Document number: DS37596 Rev. 2 - 2 Value (in mm) 0.600 0.775 0.200 0.200 0.400 0.750 1.800 0.500 1.800 C 16 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2015, Diodes Incorporated www.diodes.com AP9211 Document number: DS37596 Rev. 2 - 2 17 of 17 www.diodes.com December 2015 © Diodes Incorporated