AZETTLER AZ576-1C-110DE 20a miniature power relay Datasheet

AZ
AZ576
20A MINIATURE
POWER RELAY
FEATURES
• Class F standard
• Dielectric strength 5000Vrms
• Low cost
• Epoxy sealed versions available
• 20 Amp switching
• UL E44211
• TUV 50333135
CONTACTS
Arrangement
SPST (1 Form A)
SPDT (1 Form C)
Ratings
Resistive load:
Max. switched power: 510W or 5540VA
Max. switched current: 20A
Max. switched voltage: 30VDC or 277VAC
*Note: If switching voltage is greater than 30 VDC, special
GENERAL DATA
Life Expectancy
Mechanical
Electrical
Minimumoperations
1 x 107 ops Min. (no load)
1 x 105 ops Min. (rated load)
Operate Time (Max)
15ms at nominal coil voltage (<8ms typ)
Release Time (Max)
8ms at nominal coil voltage (<4ms typ)
(with no coil suppression)
precautions must be taken. Please contact the factory.
Rated Load
UL, CUR
20A at 277VAC Resistive, 30k cycles, 85°C
5A at 120/277VAC Pilot Duty, 30k cycles, 85°C
1HP at 120/240/480VAC, 100k cycles, 40°C
10FLA / 60LRA at 250VAC, 100k cycles, 40°C
(N.O.) 20A at 120VAC Resistive, 100k cycles, 65°C
17A at 277VAC/30VDC Resistive, 100k cycles, 105°C
16A at 277VAC Resistive, 100k cycles, 105°C
16A at 120/277VAC General Use, 85°C
8A at 120VAC Tungsten, 30k cycles, 85°C
5A at 120VAC Ballast, 25k cycles, 85°C
1.5HP at 120VAC Motor, 100k cycles, 85°C
TV-5 120VAC, 25k (N.O. only), 85°C
TV-8 120VAC, 25k (N.O. only), 40°C.
Steady state current 8A, min. inrush (peak) current 117A
(N.C.) 17A at 277VAC/30VDC Resistive, 100k cycles, 105°C
16A at 120/277VAC General Use, 30k cycles, 85°C
TÜV
17A at 277VAC / 30VDC Resistive, 100k cycles, 105°C
Dielectric Strength
5000Vrms coil to contact
(at sea level for 1 min.) 1000Vrms between open contacts
Surge Voltage
coil-contacts
10kV (1.2/50µs)
Insulation
Resistance
1000 megohms min. at 20°C
500 VDC 50% RH
Dropout
Greater than 10% of nominal coil voltage (DC)
Ambient Temperature
Operating
Storage
At nominal coil voltage
-40°C (-40°F) to 105°C (221°F)
-40°C (-40°F) to 130°C (266°F)
Vibration
1.5mm DA at 10–55 Hz
Shock
10 g
Material
Silver Tin-Oxide
Enclosure
P.B.T. polyester
Resistance
Initial 100 milliohms max. at 6VDC, 1A
Terminals
Tinned copper alloy, P. C.
Max. Solder Temp.
270°C (518°F)
Max. Solder Time
5 seconds
Max. Solvent Temp.
80°C (176°F)
Max. Immersion Time
30 seconds
Weight
12 grams
COIL
Power
At Pickup Voltage
(typical)
225mW, (DC, standard)
Max. Continuous
Dissipation
1.7W at 20°C (68°F) ambient
26°C (47°F) at nominal coil voltage
17°C (31°F) at nominal coil voltage, sensitive coil
Temperature Rise
Max. Temperature
130°C (266°F)
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Specifications subject to change without notice.
5/16/16
AZ576
RELAY ORDERING DATA
ORDER NUMBER*
COIL SPECIFICATIONS – DC COIL
Nominal Coil
VDC
3
5
Must Operate
VDC
2.25
3.75
4.5
Max. Continuous
VDC
4.5
7.5
Coil Resistance
Ohms ± 10%
22.5
62.5
Sealed
AZ576–1C–3D
AZ576–1C–5D
AZ576–1C–5DE
AZ576–1C–3DE
90
AZ576–1C–6D
AZ576–1C–6DE
6.75
9
13.5
18
202.5
360
AZ576–1C–9D
AZ576–1C–12D
AZ576–1C–9DE
AZ576–1C–12DE
15
22
11.25
16.5
22.5
33
560
1,210
AZ576–1C–15D
AZ576–1C–22D
AZ576–1C–15DE
AZ576–1C–22DE
24
36
18
27
36
1,440
AZ576–1C–24D
AZ576–1C–24DE
54
3,240
AZ576–1C–36D
AZ576–1C–36DE
48
36
72
5,760
AZ576–1C–48D
AZ576–1C–48DE
60
45
90
9,000
AZ576–1C–60D
AZ576–1C–60DE
110
77
165
30,250
AZ576–1C–110D
AZ576–1C–110DE
6
9
12
9
Unsealed
Substitute "1A" in place of "1C" to indicate Form A configuration. When suffix “E” is specified for Epoxy Seal, refer to AZ “Relay Technical Notes” on
AZ website - Product Resources. Consult factory for other PCB process conditions that may apply.
MECHANICAL DATA
.500 Max.
(12.7)
1.157 Max.
(29.4)
PC BOARD LAYOUT
VIEWED TOWARDS TERMINALS
.197
(5.0)
.598 Max.
(15.2)
.597
(15.16)
.197
(5.0)
.295
(7.5)
.295
(7.51)
.161
(4.11)
6X .020
(0.50)
.101
(2.57)
.101
(2.57)
2X ø.024
(ø0.6)
2X ø.032
(ø0.8)
6X ø.050
(ø1.3)
.295
(7.5)
6X .033
(0.84)
.197
(5.0)
.597
(15.16)
.197
(5.0)
ST484-U1
HARDWARE
.500
(12.7)
.101
(2.57 ± 0.5)
1.28
(32.5)
1.22
(30.9)
WIRING DIAGRAMS
VIEWED TOWARDS TERMINALS
5
4
3
.414
(10.5)
7
6*
.125 DIA
(0.5)
.366
(9.3)
2
RETAINING CLIP
*
8
.354
(9.0)
.177
(4.5)
MAX
.295
(7.5)
.197
(5.0)
1.385 (35.19)
1
.197
(5.0)
.895 (22.73)
.661 (16.79)
.590 (15)
.059 DIA
(1.5)
* Terminals 3 & 6 not used on form A
.118
(3.0)
ST482-3
Viewed toward terminals
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
5/16/16
Similar pages