PHILIPS FBL22031 9-bit btl 3.3v latched/registered/pass-thru futurebus transceiver with 30w termination Datasheet

INTEGRATED CIRCUITS
FBL22031
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω
termination
Product specification
Supersedes data of 1998 Sep 04
2000 Apr 18
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
• Tight output skew
• Supports live insertion
• Pins for the optional JTAG boundary scan function are provided
• High density packaging in plastic Quad Flatpack
• 5V compatible I/O on A-port
• Same pinout and function as the FBL2033 except for 30Ω series
FEATURES
• Latched, registered or straight through in either A to B or B to A
path
• Drives heavily loaded backplanes with equivalent load
impedances down to 10Ω.
• High drive 100mA BTL open collector drivers on B-port
• Allows incident wave switching in heavily loaded backplane buses
• Reduced BTL voltage swing produces less noise and reduces
termination
• The A output includes a a series resistor of 30Ω making external
power consumption
• Built-in precision band-gap reference provides accurate receiver
terminating resistors unnecessary
thresholds and improved noise immunity
• Compatible with IEEE Futurebus+ or proprietary BTL backplanes
• Each BTL driver has a dedicated Bus GND for a signal return
• Controlled output ramp and multiple GND pins minimize ground
DESCRIPTION
The FBL22031 is a 9-bit latched/registered transceiver featuring a
latched, registered or pass-thru mode in either the A-to-B or B-to-A
direction.
bounce
The FBL22031 is designed with a 30Ω series resistor in both the
HIGH and LOW states of the output.
• Glitch-free power up/power down operation
• Low ICC current
The FBL22031 is intended to provide the electrical interface to a
high performance wired-OR bus.
QUICK REFERENCE DATA
SYMBOL
TYPICAL
UNIT
tPLH
tPHL
Propagation delay
An to Bn
2.7
ns
tPLH
tPHL
Propagation delay
Bn to An
4.4
4.2
ns
CO
Output capacitance (B0 – Bn only)
IOL
Output current (B0 – Bn only)
ICC
PARAMETER
Supply current
6
pF
100
mA
AIn to Bn (outputs Low or High)
11
Bn to AOn (outputs Low)
22
Bn to AOn (outputs High)
18
mA
ORDERING INFORMATION
PACKAGE
VCC = 3.3V±10%; Tamb = –40°C to +85°C
DWG No.
52-pin Plastic Quad Flat Pack (PQFP)
FBL22031BB
SOT379-1
2000 Apr 18
2
853-2119 23499
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
BUS GND
B0
VCC
TMS (option)
TCK (option)
OEB0
OEB1
OEA
BIAS V
VCC
LOGIC GND
A0
A1
PIN CONFIGURATION
52 51 50 49 48 47 46 45 44 43 42 41 40
LOGIC GND
1
39
BUS GND
A2
2
38
B1
LOGIC GND
3
37
BUS GND
A3
4
36
B2
LOGIC GND
5
9-Bit latched/registered transceiver
35
BUS GND
A4
6
FBL22031
34
B3
LOGIC GND
7
33
BUS GND
A5
8
32
B4
52-lead PQFP
LOGIC GND
9
31
BUS GND
A6
10
30
B5
LOGIC GND
11
29
BUS GND
A7
12
28
B6
LOGIC GND
13
27
BUS GND
B7
B8
BUS GND
VCC
TDI (option)
TDO (option)
SEL0
LCAB
BG GND
BG VCC
16 17 18 19 20 21 22 23 24 25 26
LCBA
A8
SEL1
14 15
SG00091
PIN DESCRIPTION
SYMBOL
PIN NUMBER
TYPE
NAME AND FUNCTION
A0 – A8
50, 52, 2, 4, 6, 8, 10, 12, 14
I/O
BiCMOS data inputs/3-State outputs (TTL)
B0 – B8
40, 38, 36, 34, 32,
30, 28, 26, 24
I/O
Data inputs/Open Collector outputs, High current drive (BTL)
OEB0
46
Input
Enables the B outputs when High
OEB1
45
Input
Enables the B outputs when Low
OEA
47
Input
Enables the A outputs when High
BUS GND
25, 27, 29, 31, 33,
35, 37, 39, 41
GND
Bus ground (0V)
LOGIC GND
51, 1, 3, 5, 7, 9, 11, 13
GND
Logic ground (0V)
VCC
23, 43, 49
Power
Positive supply voltage
BIAS V
48
Power
Live insertion pre-bias pin
BG VCC
17
Power
Band Gap threshold voltage reference
BG GND
19
GND
Band Gap threshold voltage reference ground
SEL0
20
Input
Mode select
SEL1
15
Input
Mode select
LCAB
18
Input
A to B clock/latch enable (transparent latch when Low)
LCBA
16
Input
B to A clock/latch enable (transparent latch when Low)
TMS
42
Input
Test Mode Select (optional, if not implemented then no connect)
TCK
44
Input
Test Clock (optional, if not implemented then no connect)
TDI
22
Input
Test Data In (optional, if not implemented then no connect)
TDO
21
Output
2000 Apr 18
Test Data Out (optional, if not implemented then shorted to TDI)
3
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
drivers. BTL also provides incident wave switching, a necessity for
high performance backplanes.
DESCRIPTION
The TTL-level side (A port) has a common I/O. The common I/O,
open collector B port operates at BTL signal levels. The logic
element for data flow in each direction is controlled by two mode
select inputs (SEL0 and SEL1). A “00” configures latches in both
directions. A “10” configures thru mode in both directions. A “01”
configures register mode in both directions. A “11” configures
register mode in the A-to-B direction and latch mode in the B-to-A
direction.
Output clamps are provided on the BTL outputs to further reduce
switching noise. The “VOH” clamp reduces inductive ringing effects
during a Low-to-High transition. The “VOH” clamp is always active.
The other clamp, the “trapped reflection” clamp, clamps out ringing
below the BTL 0.5V VOL level. This clamp remains active for
approximately 100ns after a High-to-Low transition.
The 3-State A port is enabled by asserting a High level on OEA. The
B port has two output enables, OEB0 and OEB1. Only when OEB0
is High and OEB1 is Low is the output enabled.
To support live insertion, OEB0 is held Low during power on/off
cycles to insure glitch- free B port drivers. Proper bias for B port
drivers during live insertion is provided by the BIAS V pin when at a
3.3V level while VCC is Low. The BIAS V pin is a low current input
which will reverse-bias the BTL driver series Schottky diode, and
also bias the B port output pins to a voltage between 1.62V and
2.1V. This bias function is in accordance with IEEE BTL Standard
1194.1. If live insertion is not a requirement, the BIAS V pin should
be tied to a VCC pin.
When either OEB0 is Low or OEB1 is High, the B port is inactive
and is pulled to the level of the pull-up voltage. New data can be
entered in the register and latched modes or can be retained while
the associated outputs are in 3-State (A port) or inactive (B port).
The LOGIC GND and BUS GND pins are isolated inside the
package to minimize noise coupling between the BTL and TTL
sides. These pins should be tied to a common ground external to the
package.
The B-port drivers are Low-capacitance open collectors with
controlled ramp and are designed to sink 100mA. Precision band
gap references on the B-port insure very good noise margins by
limiting the switching threshold to a narrow region centered at 1.55V.
Each BTL driver has an associated BUS GND pin that acts as a
signal return path and these BUS GND pins are internally isolated
from each other. In the event of a ground return fault, a “hard” signal
failure occurs instead of a pattern dependent error that may be
infrequent and impossible to troubleshoot.
When configured in the buffer mode, the inverse of the input data
appears at the output port. In the register mode, data is stored on
the rising edge of the appropriate clock input (LCAB or LCBA). In the
latch mode, clock pins serve as transparent-Low latch enables.
Regardless of the mode, data is inverted from input to output.
The B-port interfaces to “Backplane Transceiver Logic” (see the
IEEE 1194.1 BTL standard). BTL features low power consumption
by reducing voltage swing (1V p-p, between 1V and 2V) and
reduced capacitive loading by placing an internal series diode on the
As with any high power device, thermal considerations are critical. It
is recommended that airflow (300Ifpm) and/or thermal mounting be
used to ensure proper junction temperature.
PACKAGE THERMAL CHARACTERISTICS
PARAMETER
2000 Apr 18
CONDITION
52-PIN PLASTIC QFP
θja
Still air
80°C/W
θja
300 Linear feet per minute air flow
58°C/W
θjc
Thermally mounted on one side to heat sink
20°C/W
4
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
FUNCTION TABLE
MODE
An to Bn thru mode
An to Bn transparent latch
An to Bn latch and read
Bn outputs latched and read
(preconditioned latch)
An to Bn register
Bn to An thru mode
Bn to An transparent latch
Bn to An latch and read
An outputs latched and read
(preconditioned latch)
Bn to An register
Disable Bn outputs
Disable An outputs
INPUTS
OUTPUTS
An
Bn*
OEB0
OEB1
OEA
LCAB
LCBA
SEL0
SEL1
An
Bn
L
—
H
L
L
X
X
H
L
input
H**
H
—
H
L
L
X
X
H
L
input
L
L
—
H
L
L
L
X
L
L
input
H**
H
—
H
L
L
L
X
L
L
input
L
l
—
H
L
L
↑
X
L
L
input
H**
h
—
H
L
L
↑
X
L
L
input
L
X
—
H
L
X
H
X
L
L
X
latched
data
l
—
H
L
L
↑
X
X
H
input
H**
H
L
h
—
L
↑
X
X
H
input
L
—
L
Disable
H
X
X
H
L
H
input
—
H
Disable
H
X
X
H
L
L
input
—
L
Disable
H
X
L
L
L
H
input
—
H
Disable
H
X
L
L
L
L
input
—
L
Disable
H
X
L
H
H
H
input
—
H
Disable
H
X
L
H
H
L
input
—
l
Disable
H
X
↑
L
L
H
input
—
h
Disable
H
X
↑
L
L
L
input
—
l
Disable
H
X
↑
H
H
H
input
—
h
Disable
H
X
↑
H
H
L
input
—
X
X
X
H
X
H
L
L
latched
data
X
—
X
X
X
H
X
H
H
H
latched
data
X
—
l
Disable
H
X
↑
L
H
H
input
—
h
Disable
H
X
↑
L
H
L
input
X
X
L
X
X
X
X
X
X
X
H**
X
X
X
H
X
X
X
X
X
X
H**
X
X
X
X
L
X
X
X
X
Z
X
FUNCTION SELECT TABLE
MODE SELECTED
SEL0
SEL1
Thru mode
H
L
Register mode (An to Bn)
X
H
Latch mode (An to Bn)
L
L
Register mode (Bn to An)
L
H
Latch mode (Bn to An)
NOTES:
H = High voltage level
L
= Low voltage level
l
= Low voltage level one set-up time prior to the Low-to-High
LCXX transition
h
= High voltage level one set-up time prior to the Low-to-High
LCXX transition
X = Don’t care
2000 Apr 18
Z
—
↑
H**
Bn*
L
H
High-impedance (OFF) state
Input not externally driven
Low-to-High transition
Goes to level of pull-up voltage
Precaution should be taken to ensure B inputs do not float.
If they do, they are equal to Low state.
Disable =
OEB0 is Low or OEB1 is High.
5
=
=
=
=
=
L
H
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
LOGIC DIAGRAM
OEB0
OEB1
OEA
46
45
47
D
Q
E
D
A8 14
Q
MUX
24
MUX
Q
Q
A ⇐ B
D
DD
E
Q
Q
D
Clk
E
D
A7 12
Q
26
MUX
A ⇒ B
Clk
30
MUX
Q
A ⇐ B
8
Q
D
2
D
E
6
4
Q
32
D
Clk
36
D
Q
38 B1
MUX
A ⇒ B
52
MUX
Q
A ⇐ B
D
D
E
Q
Q
D
Clk
E
D
Q
40
MUX
Clk
A0
B0
A ⇒ B
50
MUX
Q
D
Q
D
A ⇐ B
2000 Apr 18
BTL
34
E
Clk
A1
B7
28
10
TTL
B8
A ⇒ B
Clk
LCAB
18
SEL0
20
Decode
SEL1
15
In
LCBA
16
TMS
TCK
TDI
TDO
42
44
22
21
E
Clk
Out
LOGIC GND
BUS GND
BIAS V
VCC
BG VCC
BG GND
(JTAG Boundary Scan pins)
6
=
=
=
=
=
=
1, 3, 5, 7, 9, 11, 13, 51
25, 27, 29, 31, 33, 35, 37, 39, 41
48
23, 43, 49
17
19
SG00061
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
ABSOLUTE MAXIMUM RATINGS
Operation beyond the limits set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free-air temperature range.
SYMBOL
VCC
PARAMETER
Supply voltage
VIN
Input voltage
IIN
Input current
VOUT
–0.5 to +4.6
V
–0.5 to +7.0
V
B0 – B8
–0.5 to +3.5
V
–50
V
VIN t 0
Current applied to output in
Low output state/High output state
TSTG
Storage temperature
UNIT
AI0 – AI6, OEB0, OEBn, OEAn
Voltage applied to output in High output state
IOUT
O
RATING
AO0 – AO8
B0 – B8
–0.5 to +7.0
V
24, –24
mA
200
mA
–65 to +150
°C
COMMERCIAL LIMITS
VCC = 3.3V±10%;
Tamb = –40 to +85°C
UNIT
RECOMMENDED OPERATING CONDITIONS
SYMBOL
VCC
VIH
PARAMETER
Supply voltage
High level input voltage
High-level
VIL
Low level input voltage
Low-level
IIK
Input clamp current
IOH
High-level output current
IOL
O
Low level output current
Low-level
COB
Output capacitance on B port
Tamb
Operating free-air temperature range
MIN
TYP
MAX
3.0
3.3
3.6
Except B0–B8
2.0
B0 – B8
1.62
V
V
1.55
V
Except B0–B8
0.8
V
B0 – B8
1.47
V
–18
mA
AO0 – AO8
–12
mA
AO0 – AO8
+12
mA
B0 – B8
100
mA
7
pF
+70
°C
6
0
LIVE INSERTION SPECIFICATIONS
SYMBOL
LIMITS
PARAMETER
Voltage difference between the Bias voltage
and VCC after the PCB is plugged in.
UNIT
MIN
TYP
MAX
–
–
0.5
V
VBIASV
Bias pin voltage
IBIASV
S
Bias pin ((IBIASV) input DC
current
VCC = 0 V, Bias V = 3.6V
1.2
mA
VCC = 3.3V, Bias V = 3.6V
10
µA
VBn
Bus voltage during prebias
B0 – B8 = 0V, Bias V = 3.3V
2.1
V
ILM
Fall current during prebias
B0 – B8 = 2V, Bias V = 1.3 to 2.5V
1
µA
IHM
Rise current during prebias
B0 – B8 = 1V, Bias V = 3 to 3.6V
IBnPEAK
Peak bus current during
insertion
VCC = 0 to 3.3V, B0 – B8 = 0 to 2.0V,
Bias V = 2.7 to 3.6V, OEB0 = 0.8V, tr = 2ns
10
IOL
O OFF
Power up current
VCC = 0 to 3.3V, OEB0 = 0.8V
100
VCC = 0 to 1.2V, OEB0 = 0 to 5V
100
tGR
2000 Apr 18
Input glitch rejection
VCC = 3.3V
1.62
1.0
7
µA
-1
1.35
mA
µA
ns
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
DC ELECTRICAL CHARACTERISTICS
Over recommended operating free-air temperature range unless otherwise noted.
SYMBOL
IOH
TEST CONDITIONS1
PARAMETER
High level output current
B0 – B8
IOFF
O
Power off output current
Power-off
B0 – B8
VOH
High-level
Hi
hl
l output
t t
voltage
AO0 – AO83
VOL
O
Low level output voltage
Low-level
B0 – B8
VIK
II
Input clamp voltage
Input leakage current
UNIT
100
µA
100
µA
VCC = 0V, VIL = MAX, VOH = 1.9V @ 85°C
300
µA
VCC–0.2
V
VCC = MIN; IOH = –4mA
2.4
V
VCC = MIN; IOH = –12mA
2.0
V
VCC = MIN; IOL = 4mA
0.4
V
VCC = MIN; IOL = 12mA
0.8
V
VCC = MIN, IOL = 4mA
VCC = MIN, IOL = 100mA
0.5
0.75
VCC = MIN, II = IIK = –18mA
V
1.0
1.20
V
–0.85
–1.2
V
Control pins
VCC = 3.6V; VI = VCC or 100mV
±1.0
µA
Control/AI0 – AI8
VCC = 0V or 3.6V; VI = 5.5V
10
µA
AI0 – AI8
VCC = 3.6V; VI = VCC
1
µA
Note 4
VCC = 3.6V; VI = 100mV
–5
µA
VCC = MAX, VI = 1.9V
100
VCC = MAX, VI = 3.5V, note 5
100
VCC = MAX, VI = 3.75V, note 5 @ –40°C
100
High-level input current
B0 – B8
IIL
Low level input current
Low-level
B0 – B8
MAX VI = 0.75V
0 75V
VCC = MAX,
IOZH
Off-state output current
AO0 – AO8
IOZL
Off-state output current
AO0 – AO8
ICCH B to A
VCC = MAX, outputs High
ICCL B to A
VCC = MAX, outputs Low
ICCH A to B
VCC = MAX, outputs High
ICCL A to B
ICCZ
Supply current (total)
MAX
VCC = 0V, VIL = MAX, VOH = 1.9V
IIH
ICC
TYP2
VCC = MAX, VIL = MAX, VOH = 1.9V
VCC = MIN to MAX, IOH = –100µA
AO0 – AO83
LIMITS
MIN
µA
mA
mA
100
–100
µA
VCC = MAX, VO =3V
5
µA
VCC = MAX, VO = 0.5V
–5
µA
18
32
mA
22
37
mA
11
16
mA
VCC = MAX, outputs Low
11
16
mA
VCC = MAX
18
32
mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operation conditions for the applicable type.
2. All typical values are at VCC = 3.3V, TA = 25°C.
3. Due to test equipment limitations, actual test conditions are VIH = 1.8V and VIL = 1.3V for the B side.
4. Unused pins are at VCC or GND.
5. For B port input voltage between 3 and 5 volt; IIH will be greater than 100mA but the part will continue to function normally (clamping circuit
is active).
2000 Apr 18
8
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
AC ELECTRICAL CHARACTERISTICS
B TO A SPECIFICATIONS
SYMBOL
PARAMETER
Tamb = +25°C,
VCC = 3.3V,
TEST
CONDITION
MIN
TYP
Tamb = –40 to +85°C,
VCC = 3.3V±10%,
MAX
MIN
MAX
UNIT
fMAX
Maximum clock frequency
Waveform 4
120
150
tPLH
tPHL
Propagation delay (thru mode)
Bn to An
Waveform 1, 2
2.3
2.6
5.4
5.6
8.9
9.1
1.7
2.1
10.1
10.3
MHz
ns
tPLH
tPHL
Propagation delay (transparent latch)
Bn to An
Waveform 1, 2
3.2
3.5
6.5
6.3
10.1
9.3
2.4
2.9
11.6
10.3
ns
tPLH
tPHL
Propagation delay
LCBA to An (latch)
Waveform 1, 2
6.8
5.5
10.4
9.8
14.4
14.7
5.1
4.3
16.9
16.8
ns
tPLH
tPHL
Propagation delay
LCBA to An (register)
Waveform 1, 2
2.1
2.3
4.9
5.2
8.4
8.3
1.2
1.8
9.7
9.4
ns
tPLH
tPHL
Propagation delay
SEL0 or SEL1 to An (inverting)
Waveform 1, 2
2.7
2.5
6.5
6.3
10.7
10.5
1.8
2.0
12.8
11.8
ns
tPLH
tPHL
Propagation delay
SEL0 or SEL1 to An (non-inverting)
Waveform 1, 2
2.4
2.6
6.6
6.2
11.3
10.2
1.8
2.1
13.0
11.6
ns
tPZH
tPHZ
Output enable time from High or Low
OEA to An
Waveform 5, 6
2.6
3.4
5.8
5.4
9.3
7.5
1.9
2.9
10.7
9.0
ns
tPZL
tPLZ
Output disable time to High or Low
OEA to An
Waveform 5, 6
2.1
1.2
5.4
3.1
9.1
5.4
1.6
1.0
10.1
6.0
ns
tTLH
tTHL
Output transition time, An Port
10% to 90%, 90% to 10%
Test Circuit and
Waveforms
0.7
0.5
3.0
2.0
ns
tSK(o)
Output to output skew for multiple
channels1
Waveform 3
0.5
1.0
1.5
ns
tSK(p)
Pulse skew2
 tPHL – tPLH  MAX
Waveform 2
0.5
1.0
1.5
ns
NOTES:
1.  tPNactual – tPMactual for any data input to output path compared to any other data input to output path where N and M are either LH or HL.
Skew times are valid only under same test conditions (temperature, VCC, loading, etc.). tSK (0) compares tPLH on a given path to tPLH on any
other path or compares tPHL on a given path to tPHL on any other path.
2. tSK(p) is used to quantify duty cycle characteristics. In essence it compares the input signal duty cycle to the corresponding output signal
duty cycle (50MHz input frequency and 50% duty cycle, tested on data paths only).
2000 Apr 18
9
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
AC ELECTRICAL CHARACTERISTICS
A TO B
SYMBOL
PARAMETER
9 Ω LOAD SPECIFICATIONS
Tamb = +25°C,
VCC = 3.3V,
TEST
CONDITION
Tamb = –40 to +85°C,
VCC = 3.3V±10%,
MIN
TYP
MAX
MIN
MAX
UNIT
tPLH
tPHL
Propagation delay (thru latch)
An to Bn
Waveform 1, 2
1.2
1.2
3.5
3.1
8.1
6.5
1.0
1.0
9.1
6.9
ns
tPLH
tPHL
Propagation delay (transparent latch)
An to Bn
Waveform 1, 2
1.2
1.3
3.8
4.0
8.6
7.7
1.0
1.0
9.5
8.4
ns
tPLH
tPHL
Propagation delay
LCAB to Bn (latch)
Waveform 1, 2
7.2
7.2
12.0
11.1
17.4
15.5
5.3
5.6
20.5
17.8
ns
tPLH
tPHL
Propagation delay
LCAB to Bn (register)
Waveform 1, 2
1.2
1.4
4.4
4.3
8.8
7.5
1.0
1.0
10.2
8.4
ns
tPLH
tPHL
Propagation delay
SEL0 or SEL1 to Bn (inverting)
Waveform 1, 2
1.2
1.6
5.1
4.6
9.8
8.1
1.0
1.1
11.4
9.9
ns
tPLH
tPHL
Propagation delay
SEL0 or SEL1 to Bn (non-inverting)
Waveform 1, 2
1.9
1.9
5.6
4.7
9.9
7.9
1.0
1.3
11.2
9.0
ns
tPLH
tPHL
OEBn to Bn
Waveform 1, 2
1.2
1.2
4.0
3.7
8.4
6.7
1.0
1.0
9.8
8.0
ns
tTLH
tTHL
Output transition time, Bn Port
(1.3V to 1.8V)
Test Circuit and
Waveforms
1.2
0.4
3.0
1.5
ns
tSK(o)
Output to output skew for multiple
channels1
Waveform 3
0.4
1.0
2.0
ns
tSK(p)
Pulse skew2
 tPHL – tPLH  MAX
Waveform 2
0.3
1.0
1.5
ns
NOTES:
1.  tPNactual – tPMactual for any data input to output path compared to any other data input to output path where N and M are either LH or
HL. Skew times are valid only under same test conditions (temperature, VCC, loading, etc.). tSK (0) compares tPLH on a given path to tPLH
on any other path or compares tPHL on a given path to tPHL on any other path.
2. tSK(p) is used to quantify duty cycle characteristics. In essence it compares the input signal duty cycle to the corresponding output signal
duty cycle (50MHz input frequency and 50% duty cycle, tested on data paths only).
2000 Apr 18
10
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
AC ELECTRICAL CHARACTERISTICS
A TO B
SYMBOL
PARAMETER
16.5 Ω LOAD SPECIFICATIONS
Tamb = +25°C,
VCC = 3.3V,
TEST
CONDITION
Tamb = –40 to +85°C,
VCC = 3.3V±10%,
MIN
TYP
MAX
MIN
MAX
UNIT
tPLH
tPHL
Propagation delay (thru latch)
An to Bn
Waveform 1, 2
1.2
1.3
4.1
3.5
7.4
5.9
1.0
1.1
8.7
6.4
ns
tPLH
tPHL
Propagation delay (transparent latch)
An to Bn
Waveform 1, 2
1.2
1.6
4.3
4.3
8.0
7.3
1.0
1.2
9.3
8.1
ns
tPLH
tPHL
Propagation delay
LCAB to Bn (latch)
Waveform 1, 2
6.6
6.7
11.8
10.9
17.6
15.7
4.8
5.2
20.6
18.1
ns
tPLH
tPHL
Propagation delay
LCAB to Bn (register)
Waveform 1, 2
1.2
1.2
4.3
4.1
8.8
7.6
1.0
1.0
10.1
8.5
ns
tPLH
tPHL
Propagation delay
SEL0 or SEL1 to Bn (inverting)
Waveform 1, 2
1.3
1.7
5.3
4.9
9.7
8.6
1.0
1.3
11.2
9.6
ns
tPLH
tPHL
Propagation delay
SEL0 or SEL1 to Bn (non-inverting)
Waveform 1, 2
1.8
1.8
5.6
4.7
9.8
7.9
1.0
1.1
11.3
9.0
ns
tPLH
tPHL
OEBn to Bn
Waveform 1, 2
1.3
1.7
4.4
4.0
8.1
6.7
1.0
1.0
9.4
7.8
ns
tTLH
tTHL
Output transition time, Bn Port
(1.3V to 1.8V)
Test Circuit and
Waveforms
1.2
0.4
3.0
1.5
ns
tSK(o)
Output to output skew for multiple
channels1
Waveform 3
0.4
1.0
2.0
ns
tSK(p)
Pulse skew2
 tPHL – tPLH  MAX
Waveform 2
0.3
1.0
1.5
ns
NOTES:
1.  tPNactual – tPMactual for any data input to output path compared to any other data input to output path where N and M are either LH or
HL. Skew times are valid only under same test conditions (temperature, VCC, loading, etc.). tSK (0) compares tPLH on a given path to tPLH
on any other path or compares tPHL on a given path to tPHL on any other path.
2. tSK(p) is used to quantify duty cycle characteristics. In essence it compares the input signal duty cycle to the corresponding output signal
duty cycle (50MHz input frequency and 50% duty cycle, tested on data paths only).
2000 Apr 18
11
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
AC SETUP REQUIREMENTS (Commercial)
LIMITS
SYMBOL
TEST
CONDITION
PARAMETER
Setup time
An to LCAB
th(H)
th(L)
UNIT
CL = 50pF (A side) / CD = 30pF (B side)
RL = 500Ω (A side) / RU = 16.5Ω (B side)
MIN
ts(H)
ts(L)
Tamb = –40 to +85°C,
VCC = 3.3V±10%,
Tamb = +25°C, VCC = 3.3V,
TYP
MIN
Waveform 4
1.3
1.3
1.5
1.5
ns
Hold time
An to LCAB
Waveform 4
1.0
1.0
1.0
1.0
ns
ts(H)
ts(L)
Setup time
Bn to LCBA
Waveform 4
5.0
4.0
6.0
4.5
ns
th(H)
th(L)
Hold time
Bn to LCBA
Waveform 4
0.0
0.0
0.0
0.0
ns
tw(H)
tw(L)
Pulse width, High or Low
LCAB or LCBA
Waveform 4
3.0
3.0
3.0
3.0
ns
AC WAVEFORMS
VM
Input
Output
tPLH
tw (output)
VM
VM
Waveform 2. Propagation Delay for Data
or Output Enable to Output
ÍÍÍÍÍÍ ÍÍ
ÍÍÍÍÍÍ ÍÍ
An, Bn
VM
VM
ts
tSK(o)
An, Bn
VM
tw (input)
tPHL
VM
Waveform 1. Propagation Delay for Data
or Output Enable to Output
An, Bn
VM
tPHL
VM
Output
Input
VM
tPLH
LCAB, LCBA
VM
th
VM
ts
tw(L)
tw(H)
th
VM
1/fMAX
Waveform 3. Output to Output Skew
OEA
VM
VM
tPZH
An
Waveform 4. Setup and Hold Times,
Pulse Widths and Maximum Frequency
OEA
tPHZ
VM
VOH -0.3V
tPZL
OV
An
Waveform 5. 3-State Output Enable Time to High Level
and Output Disable Time from High Level
tPLZ
VM
VOL +0.3V
Waveform 6. 3-State Output Enable Time to Low Level
and Output Disable Time from Low Level
NOTE: VM = 1.55V for Bn, VM = 1.5V for all others.
The shaded areas indicate when the input is permitted to change for predictable output performance.
2000 Apr 18
VM
VM
12
SG00062
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
TEST CIRCUIT AND WAVEFORMS
VCC
VIN
RL
VOUT
PULSE
GENERATOR
tW
90%
7.0V
NEGATIVE
PULSE
VM
VM
10%
D.U.T.
RT
CL
AMP (V)
90%
RL
10%
tTHL
(tf)
tTLH
(tr)
LOW V
tTLH
(tr)
tTHL
(tf)
AMP (V)
90%
90%
POSITIVE
PULSE
Test Circuit for 3-State Outputs on A Port
LOW V
VM = 1.55V for Bn, VM = 1.5V for all others.
Input Pulse Definitions
SWITCH
tPLZ, tPZL
All other
closed
open
VCC
BIAS
V
VIN
2.0V (for RU = 9 Ω)
2.1V (for RU = 16.5 Ω)
VOUT
PULSE
GENERATOR
RU
D.U.T.
RT
Test Circuit for Outputs on B Port
2000 Apr 18
10%
tW
SWITCH POSITION
TEST
VM
VM
10%
CD
INPUT PULSE REQUIREMENTS
Family
FB+
Amplitude
Low V
Rep. Rate
A Port
3.0V
0.0V
1MHz
500ns 2.5ns
2.5ns
B Port
2.0V
1.0V
1MHz
500ns 2.0ns
2.0ns
tW
tTLH
tTHL
DEFINITIONS:
RL = Load Resistor; see AC CHARACTERISTICS for value.
CL = Load capacitance includes jig and probe capacitance; see AC
CHARACTERISTICS for value.
RT = Termination resistance should be equal to ZOUT of pulse generators.
CD = Load capacitance includes jig and probe capacitance; see AC
CHARACTERISTICS for value.
RU = Pull up resistor; see AC CHARACTERISTICS for value.
SG00063
13
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
QFP52: plastic quad flat package; 52 leads (lead length 1.6 mm); body 10 x 10 x 2.0 mm
2000 Apr 18
14
FBL22031
SOT379-1
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
NOTES
2000 Apr 18
15
FBL22031
Philips Semiconductors
Product specification
9-bit BTL 3.3V latched/registered/pass-thru
Futurebus+ transceiver with 30Ω termination
FBL22031
Data sheet status
Data sheet
status
Product
status
Definition [1]
Objective
specification
Development
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
Preliminary
specification
Qualification
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make changes at any time without notice in order to
improve design and supply the best possible product.
Product
specification
Production
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
 Copyright Philips Electronics North America Corporation 2000
All rights reserved. Printed in U.S.A.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
Date of release: 04-00
Document order number:
2000 Apr 18
16
9397 750 07091
Similar pages