TDK MLK0603L1N5ST Inductors for high frequency Datasheet

I
N
D
U
C
T
O
R
S
July 2013
Inductors for High Frequency
Multilayer Ceramic
MLK series
MLK0603
MLK1005
0603 [0201 inch]*
1005 [0402 inch]
* Dimensions Code JIS[EIA]
(1/14)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(2/14)
I
N
D
U
C
T
O
R
S
Inductors for High Frequency Circuits
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
Multilayer Ceramic
Overview of the MLK Series
FEATURES
With the adoption of a giga-spiral laminated structure, a self-resonant frequency higher than that of the MLG structure can be obtained,
while the decrease of Q in the GHz band is limited.
Monolithic structure is formed using a multilayering and sintering process with ceramic and conductive materials for high-frequency.
There is no directivity.
APPLICATION
Smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners, automotive equipment
(MLK1005) and other high frequency circuits for the mobile communication industry
PART NUMBER CONSTRUCTION
MLK
Series name
0603
L×W×H Dimensions
(mm)
0603
0.6×0.3×0.3
1005
1.0×0.5×0.5
L
Characteristics
L
S
1N1
J
Inductance
(μH)
1N1
1.1
11N
11
R10
100
Inductance
tolerance
S
±0.3nH
J
±5%
T
□□□
Packaging style
Internal code
T
Taping
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Operating
Storage
Type
temperature
temperature
(pieces/reel)
（°C）
（°C）
MLK0603
–55 to +125
–55 to +125
15000
MLK1005
–55 to +125
–55 to +125
10000
The Storage temperature range is for after the circuit board is mounted.
Individual weight
（mg）
0.2
1
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(3/14)
I
N
D
U
C
T
O
R
S
Overview of the MLK Series
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1
t1
t2
t: Time
Preheating
Temp.
T1
T2
150°C
180°C
Time
t1
60 to 120s
Soldering
Temp.
Time
T3
t2
230°C
30 to 60s
Peak
Temp.
T4
250 to 260°C
Time
t3
10s max.
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(4/14)
I
N
D
U
C
T
O
R
S
MLK series
MLK0603 Type
0.30±0.03
SHAPE & DIMENSIONS
0.15±0.05
0.15±0.05
0.30±0.03
0.6±0.03
Dimensions in mm
0.3
RECOMMENDED LAND PATTERN
0.25
0.3
0.25
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(5/14)
I
N
D
U
C
T
O
R
S
MLK series MLK0603 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
L
(nH)
1.0
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.2
2.4
2.7
3.0
3.3
3.6
3.9
4.3
4.7
5.1
5.6
6.2
6.8
7.5
8.2
9.1
10
12
15
18
22
27
33
Tolerance
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
Self-resonant
L measuring
Q measuring
frequency
Q
frequency
frequency
(GHz)
min.
(MHz)
(MHz)
min.
typ.
100
6
300
12.0
17.1
100
6
300
11.0
17.1
100
6
300
11.0
16.1
100
6
300
10.0
15.8
100
6
300
10.0
14.9
100
6
300
10.0
14.3
100
6
300
10.0
13.8
100
6
300
9.0
12.6
100
6
300
9.0
12.5
100
6
300
8.5
11.4
100
6
300
8.5
10.9
100
6
300
8.0
10.6
100
6
300
8.0
10.5
100
6
300
8.0
9.9
100
6
300
8.0
9.8
100
6
300
7.5
9.5
100
6
300
7.5
9.5
100
6
300
6.5
8.8
100
6
300
6.5
8.5
100
6
300
6.0
8.3
100
6
300
6.0
8.1
100
6
300
6.0
7.7
100
6
300
6.0
7.9
100
6
300
5.5
7.4
100
6
300
5.5
7.5
100
6
300
5.0
6.9
100
6
300
4.5
6.6
100
6
300
4.0
5.8
100
6
300
3.5
5.3
100
6
300
3.0
4.6
100
6
300
2.8
4.4
DC resistance
(: )
max.
0.20
0.22
0.22
0.24
0.24
0.27
0.27
0.30
0.30
0.35
0.35
0.40
0.40
0.45
0.45
0.50
0.50
0.60
0.60
0.65
0.65
0.70
0.70
0.80
0.80
1.00
1.10
1.30
1.60
1.70
1.80
typ.
0.09
0.10
0.11
0.12
0.12
0.13
0.14
0.15
0.17
0.17
0.18
0.20
0.22
0.22
0.25
0.28
0.28
0.28
0.30
0.34
0.34
0.36
0.41
0.42
0.48
0.54
0.66
0.85
1.02
1.09
1.21
Rated current
(mA)
max.
Part No.*
300
300
300
300
300
300
300
300
300
300
300
200
200
200
200
200
200
200
200
200
200
200
200
200
200
150
150
100
100
100
100
MLK0603L1N0ST□□□
MLK0603L1N1ST□□□
MLK0603L1N2ST□□□
MLK0603L1N3ST□□□
MLK0603L1N5ST□□□
MLK0603L1N6ST□□□
MLK0603L1N8ST□□□
MLK0603L2N0ST□□□
MLK0603L2N2ST□□□
MLK0603L2N4ST□□□
MLK0603L2N7ST□□□
MLK0603L3N0ST□□□
MLK0603L3N3ST□□□
MLK0603L3N6ST□□□
MLK0603L3N9ST□□□
MLK0603L4N3ST□□□
MLK0603L4N7ST□□□
MLK0603L5N1ST□□□
MLK0603L5N6ST□□□
MLK0603L6N2ST□□□
MLK0603L6N8JT□□□
MLK0603L7N5JT□□□
MLK0603L8N2JT□□□
MLK0603L9N1JT□□□
MLK0603L10NJT□□□
MLK0603L12NJT□□□
MLK0603L15NJT□□□
MLK0603L18NJT□□□
MLK0603L22NJT□□□
MLK0603L27NJT□□□
MLK0603L33NJT□□□
The " □□□ " of the Part Number contains the internal code.
○ Measurement equipment
Measurement item
Product No.
L, Q
4291B+16197A
Self-resonant frequency
8720C
DC resistance
Type-7561
＊ Equivalent measurement equipment may be used.
Manufacturer
Agilent Technologies
Agilent Technologies
Yokogawa
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(6/14)
I
N
D
U
C
T
O
R
S
MLK series MLK0603 Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
L(nH)typ.
500MHz
0.9
1.0
1.1
1.2
1.3
1.4
1.6
1.8
2.0
2.1
2.4
2.7
3.0
3.2
3.5
3.8
4.2
4.6
5.0
5.5
6.2
6.7
7.4
8.2
9.0
10.8
13.5
16.2
19.8
24.4
29.7
800MHz
0.9
1.0
1.0
1.1
1.3
1.4
1.6
1.7
1.9
2.1
2.4
2.6
2.9
3.1
3.4
3.8
4.2
4.5
5.0
5.5
6.1
6.6
7.3
8.1
8.9
10.6
13.4
16.1
19.7
24.4
29.7
1.8GHz
0.9
0.9
1.0
1.1
1.3
1.4
1.6
1.7
1.9
2.1
2.4
2.6
2.9
3.1
3.5
3.8
4.2
4.5
5.0
5.5
6.2
6.7
7.5
8.3
9.2
11.0
13.9
17.0
20.9
27.2
33.4
2.0GHz
0.9
0.9
1.0
1.1
1.3
1.4
1.6
1.7
1.9
2.1
2.4
2.6
3.0
3.1
3.5
3.8
4.2
4.6
5.0
5.6
6.2
6.8
7.6
8.4
9.3
11.2
14.2
17.4
21.5
28.6
35.1
2.4GHz
0.9
0.9
1.0
1.1
1.3
1.4
1.6
1.7
2.0
2.1
2.4
2.7
3.0
3.2
3.5
3.9
4.3
4.7
5.1
5.7
6.4
7.0
7.8
8.6
9.6
11.6
14.8
18.4
22.8
31.7
39.3
Q typ.
500MHz
10
9
9
9
9
9
9
9
10
9
10
9
10
9
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
9
800MHz
12
11
12
12
12
12
11
12
12
12
13
12
13
11
13
12
13
12
12
12
13
12
13
12
13
12
12
12
12
12
11
1.8GHz
19
17
18
18
18
18
17
17
19
18
19
18
19
17
19
18
19
18
18
18
19
18
19
18
18
18
17
16
16
15
14
2.0GHz
20
18
19
19
19
19
18
18
20
19
20
19
20
18
20
19
20
19
19
19
20
19
20
18
19
18
18
17
16
15
14
2.4GHz
22
20
21
21
21
21
20
20
22
20
22
21
22
19
22
20
22
21
21
20
22
20
21
20
20
20
19
18
17
14
13
Part No.*
MLK0603L1N0ST□□□
MLK0603L1N1ST□□□
MLK0603L1N2ST□□□
MLK0603L1N3ST□□□
MLK0603L1N5ST□□□
MLK0603L1N6ST□□□
MLK0603L1N8ST□□□
MLK0603L2N0ST□□□
MLK0603L2N2ST□□□
MLK0603L2N4ST□□□
MLK0603L2N7ST□□□
MLK0603L3N0ST□□□
MLK0603L3N3ST□□□
MLK0603L3N6ST□□□
MLK0603L3N9ST□□□
MLK0603L4N3ST□□□
MLK0603L4N7ST□□□
MLK0603L5N1ST□□□
MLK0603L5N6ST□□□
MLK0603L6N2ST□□□
MLK0603L6N8JT□□□
MLK0603L7N5JT□□□
MLK0603L8N2JT□□□
MLK0603L9N1JT□□□
MLK0603L10NJT□□□
MLK0603L12NJT□□□
MLK0603L15NJT□□□
MLK0603L18NJT□□□
MLK0603L22NJT□□□
MLK0603L27NJT□□□
MLK0603L33NJT□□□
The " □□□ " of the Part Number contains the internal code.
○ Measurement equipment
Product No.
Manufacturer
4291B+16197A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(7/14)
I
N
D
U
C
T
O
R
S
MLK series MLK0603 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
1000
100
33N
27N
22N
Inductance(nH)
18N
15N
12N
10
10N
8N2
6N8
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1
1N0
0
10
100
1000
10000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16197A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(8/14)
I
N
D
U
C
T
O
R
S
MLK series MLK0603 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
30
3N3
6N8
2N7
3N9
4N7
1N0
1N2
8N2
1N5
2N2
10N
5N6
1N8
12N
20
15N
18N
Q
22N
27N
33N
10
0
10
100
1000
10000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16197A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(9/14)
I
N
D
U
C
T
O
R
S
MLK series
MLK1005 Type
0.50±0.10
SHAPE & DIMENSIONS
0.1min.
0.1min.
0.50±0.10
1.00±0.10
Dimensions in mm
0.5
RECOMMENDED LAND PATTERN
0.5
0.4
0.5
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(10/14)
I
N
D
U
C
T
O
R
S
MLK series MLK1005 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
L
Q
min.
(nH)
1.0
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.2
2.4
2.7
3.0
3.3
3.6
3.9
4.3
4.7
5.1
5.6
6.2
6.8
7.5
8.2
9.1
10
12
15
18
22
27
33
39
47
56
68
82
100
110
120
130
150
160
180
200
220
240
270
300
330
Tolerance
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±0.3nH
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
5
5
5
5
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
Q measuring
frequency
(MHz)
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
Self-resonant
frequency
(GHz)
min.
typ.
12.0
16.9
11.5
14.8
11.0
14.4
10.0
12.6
9.5
12.2
9.0
11.9
8.5
10.9
8.3
10.0
8.0
9.6
7.8
9.5
7.5
9.1
7.2
8.5
7.0
8.3
6.8
8.1
6.5
7.8
6.3
7.4
6.0
6.9
5.8
7.0
5.7
6.7
5.6
6.5
5.5
6.3
5.0
6.0
5.0
6.0
4.8
5.9
4.7
5.2
4.3
5.3
4.0
4.8
4.0
4.7
3.5
4.4
3.0
3.9
2.5
3.5
2.0
3.1
1.8
3.0
1.5
2.6
1.4
2.4
1.3
2.2
1.1
1.9
1.1
2.0
1.1
1.9
1.1
1.8
1.1
1.7
1.1
1.7
1.1
1.6
1.1
1.5
1.0
1.4
1.0
1.3
0.9
1.2
0.9
1.2
0.85
1.1
DC resistance
(: )
max.
0.10
0.12
0.12
0.15
0.15
0.17
0.17
0.18
0.18
0.20
0.20
0.22
0.22
0.25
0.25
0.28
0.28
0.30
0.30
0.35
0.35
0.38
0.38
0.42
0.42
0.47
0.50
0.60
0.70
0.80
0.90
1.00
1.20
1.30
1.50
1.80
2.20
2.70
3.00
3.30
5.00
5.20
6.00
6.20
6.20
6.50
6.50
7.50
8.00
typ.
0.05
0.05
0.05
0.06
0.06
0.06
0.07
0.08
0.08
0.09
0.10
0.10
0.11
0.11
0.12
0.13
0.13
0.15
0.15
0.18
0.18
0.20
0.21
0.23
0.23
0.27
0.33
0.38
0.46
0.53
0.59
0.65
0.74
0.84
1.01
1.39
1.60
1.89
2.08
2.28
3.58
3.79
4.28
4.56
4.54
4.84
4.78
5.37
5.82
Rated current
(mA)
max.
Part No.
500
500
500
500
500
500
500
500
500
500
500
400
400
400
400
400
400
400
400
400
400
350
350
350
350
350
300
250
200
200
200
200
200
200
150
150
100
100
100
100
80
80
80
70
70
70
70
70
70
MLK1005S1N0△T□□□
MLK1005S1N1△T□□□
MLK1005S1N2△T□□□
MLK1005S1N3△T□□□
MLK1005S1N5△T□□□
MLK1005S1N6△T□□□
MLK1005S1N8△T□□□
MLK1005S2N0△T□□□
MLK1005S2N2△T□□□
MLK1005S2N4△T□□□
MLK1005S2N7△T□□□
MLK1005S3N0△T□□□
MLK1005S3N3△T□□□
MLK1005S3N6△T□□□
MLK1005S3N9△T□□□
MLK1005S4N3△T□□□
MLK1005S4N7△T□□□
MLK1005S5N1△T□□□
MLK1005S5N6△T□□□
MLK1005S6N2△T□□□
MLK1005S6N8△T□□□
MLK1005S7N5△T□□□
MLK1005S8N2△T□□□
MLK1005S9N1△T□□□
MLK1005S10N△T□□□
MLK1005S12N△T□□□
MLK1005S15N△T□□□
MLK1005S18N△T□□□
MLK1005S22N△T□□□
MLK1005S27N△T□□□
MLK1005S33N△T□□□
MLK1005S39N△T□□□
MLK1005S47N△T□□□
MLK1005S56N△T□□□
MLK1005S68N△T□□□
MLK1005S82N△T□□□
MLK1005SR10△T□□□
MLK1005SR11△T□□□
MLK1005SR12△T□□□
MLK1005SR13△T□□□
MLK1005SR15△T□□□
MLK1005SR16△T□□□
MLK1005SR18△T□□□
MLK1005SR20△T□□□
MLK1005SR22△T□□□
MLK1005SR24△T□□□
MLK1005SR27△T□□□
MLK1005SR30△T□□□
MLK1005SR33△T□□□
The " △ " of the Part Number contains the inductance tolerance code, S(±0.3nH) or J(±5%).
The " □□□ " of the Part Number contains the internal code.
○ Measurement equipment
Measurement item
Product No.
L, Q
4291B+16193A
Self-resonant frequency
8720C
DC resistance
Type-7561
＊ Equivalent measurement equipment may be used.
Manufacturer
Agilent Technologies
Agilent Technologies
Yokogawa
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(11/14)
I
N
D
U
C
T
O
R
S
MLK series MLK1005 Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
L(nH)typ.
500MHz
0.9
1.0
1.1
1.2
1.4
1.5
1.7
1.9
2.0
2.2
2.5
2.8
3.1
3.4
3.7
4.0
4.4
4.8
5.3
5.8
6.4
7.1
7.7
8.6
9.4
11.3
14.2
17.0
20.8
25.6
31.4
37.2
45.0
53.7
65.5
79.3
97.1
107.8
118.0
127.5
149.4
160.5
181.1
202.8
225.7
248.3
290.0
323.1
358.9
800MHz
0.9
1.0
1.1
1.2
1.4
1.5
1.7
1.8
2.0
2.2
2.5
2.8
3.1
3.3
3.6
4.0
4.4
4.8
5.2
5.8
6.4
7.0
7.7
8.6
9.4
11.3
14.2
17.1
20.9
25.9
31.9
38.1
46.2
55.4
68.4
83.6
103.2
115.9
127.8
139.5
166.0
179.4
204.1
231.9
266.8
299.6
386.0
432.6
493.1
1.8GHz
0.9
1.0
1.1
1.2
1.4
1.5
1.7
1.9
2.0
2.2
2.5
2.8
3.1
3.4
3.7
4.1
4.5
4.9
5.4
6.0
6.6
7.4
8.1
9.1
10.0
12.1
15.3
18.6
23.0
29.8
37.6
48.9
60.6
76.7
105.6
142.7
199.4
2.0GHz
0.9
1.0
1.1
1.2
1.4
1.5
1.7
1.9
2.0
2.3
2.6
2.9
3.1
3.5
3.7
4.2
4.6
5.0
5.5
6.2
6.7
7.6
8.3
9.3
10.2
12.4
15.8
19.2
23.9
31.5
40.2
2.4GHz
0.9
1.0
1.1
1.2
1.4
1.5
1.7
1.9
2.1
2.3
2.6
2.9
3.2
3.5
3.8
4.3
4.7
5.1
5.7
6.4
7.0
7.9
8.6
9.7
10.7
13.0
16.8
20.6
25.8
35.7
Q typ.
500MHz
16
16
15
17
15
17
16
16
15
16
17
18
16
17
17
17
17
17
17
18
17
18
19
18
19
19
18
18
18
18
18
17
18
17
17
16
15
16
16
14
16
16
16
15
15
14
14
14
13
800MHz
20
20
18
20
19
21
21
20
19
20
22
22
20
22
21
22
22
22
22
23
22
23
23
23
23
23
23
23
23
23
23
21
21
21
20
19
18
18
18
16
17
18
17
17
15
15
12
12
12
1.8GHz
30
32
28
33
29
34
32
32
29
32
33
35
31
33
32
34
33
33
33
34
32
34
34
34
34
34
33
32
32
30
29
24
24
22
18
15
13
2.0GHz
32
35
30
35
31
36
33
34
31
34
35
36
32
35
33
35
35
35
34
35
33
36
36
36
35
35
34
33
33
30
29
2.4GHz
36
39
33
39
34
40
37
38
34
38
39
41
36
39
37
39
38
38
38
39
36
38
38
38
38
37
35
34
34
28
Part No.*
MLK1005S1N0△T□□□
MLK1005S1N1△T□□□
MLK1005S1N2△T□□□
MLK1005S1N3△T□□□
MLK1005S1N5△T□□□
MLK1005S1N6△T□□□
MLK1005S1N8△T□□□
MLK1005S2N0△T□□□
MLK1005S2N2△T□□□
MLK1005S2N4△T□□□
MLK1005S2N7△T□□□
MLK1005S3N0△T□□□
MLK1005S3N3△T□□□
MLK1005S3N6△T□□□
MLK1005S3N9△T□□□
MLK1005S4N3△T□□□
MLK1005S4N7△T□□□
MLK1005S5N1△T□□□
MLK1005S5N6△T□□□
MLK1005S6N2△T□□□
MLK1005S6N8△T□□□
MLK1005S7N5△T□□□
MLK1005S8N2△T□□□
MLK1005S9N1△T□□□
MLK1005S10N△T□□□
MLK1005S12N△T□□□
MLK1005S15N△T□□□
MLK1005S18N△T□□□
MLK1005S22N△T□□□
MLK1005S27N△T□□□
MLK1005S33N△T□□□
MLK1005S39N△T□□□
MLK1005S47N△T□□□
MLK1005S56N△T□□□
MLK1005S68N△T□□□
MLK1005S82N△T□□□
MLK1005SR10△T□□□
MLK1005SR11△T□□□
MLK1005SR12△T□□□
MLK1005SR13△T□□□
MLK1005SR15△T□□□
MLK1005SR16△T□□□
MLK1005SR18△T□□□
MLK1005SR20△T□□□
MLK1005SR22△T□□□
MLK1005SR24△T□□□
MLK1005SR27△T□□□
MLK1005SR30△T□□□
MLK1005SR33△T□□□
The " △ " of the Part Number contains the inductance tolerance code, S(±0.3nH) or J(±5%).
The " □□□ " of the Part Number contains the internal code.
○ Measurement equipment
Product No.
Manufacturer
4291B+16193A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(12/14)
I
N
D
U
C
T
O
R
S
MLK series MLK1005 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
1000
R33
R27
R22
R12
R10
82N
56N
R18
68N
R15
47N
39N
100
33N
27N
22N
18N
Inductance(nH)
15N
12N
10N
10
8N2
6N8
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1
0
10
1N0
100
1000
10000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16193A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(13/14)
I
N
D
U
C
T
O
R
S
MLK series MLK1005 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
50
2N7
1N8
1N0
4N7
3N9
40
5N6
1N5
3N3
6N8
12N
10N
15N
8N2
1N2
2N2
18N
22N
Q
30
27N
20
33N
R15
R22
R18
R27
R33
10
39N
47N
68N
82N
R10
56N
R12
0
10
100
1000
10000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16193A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm
(14/14)
I
N
D
U
C
T
O
R
S
MLK series
Packaging Style
REEL DIMENSIONS
ø60min.
1.0
2.0±0.5
8.4 +2.0
–0.0
ø13±0.2
14.4max.
ø21±0.8
ø180±2.0
Dimensions in mm
3.5±0.05
Cavity
Type
MLK0603
MLK1005
A
0.5 max.
0.8 max.
B
0.38±0.05
0.67±0.1
C
0.68±0.05
1.15±0.1
C
8.0±0.3
Sprocket hole
1.5 +0.1
–0.0
1.75±0.1
TAPE DIMENSIONS
A
B
4.0±0.1
2.0±0.05
160min.
Taping
2.0±0.05
200min.
Drawing direction
300min.
• All specifications are subject to change without notice.
001-01 / 20130707 / inductor_high-frequency_mlk_en.fm